Abstract: Microscopic simulation tool kits allow for
consideration of the two processes of railway operations and the
previous timetable production. Block occupation conflicts on both
process levels are often solved by using defined train priorities. These
conflict resolutions (dispatching decisions) generate reactionary
delays to the involved trains. The sum of reactionary delays is
commonly used to evaluate the quality of railway operations, which
describes the timetable robustness. It is either compared to an
acceptable train performance or the delays are appraised
economically by linear monetary functions. It is impossible to
adequately evaluate dispatching decisions without a well-founded
objective function. This paper presents a new approach for the
evaluation of dispatching decisions. The approach uses mode choice
models and considers the behaviour of the end-customers. These
models evaluate the reactionary delays in more detail and consider
other competing modes of transport. The new approach pursues the
coupling of a microscopic model of railway operations with the
macroscopic choice mode model. At first, it will be implemented for
railway operations process but it can also be used for timetable
production. The evaluation considers the possibility for the customer
to interchange to other transport modes. The new approach starts to
look at rail and road, but it can also be extended to air travel. The
result of mode choice models is the modal split. The reactions by the
end-customers have an impact on the revenue of the train operating
companies. Different purposes of travel have different payment
reserves and tolerances towards late running. Aside from changes to
revenues, longer journey times can also generate additional costs.
The costs are either time- or track-specific and arise from required
changes to rolling stock or train crew cycles. Only the variable values
are summarised in the contribution margin, which is the base for the
monetary evaluation of delays. The contribution margin is calculated
for different possible solutions to the same conflict. The conflict
resolution is optimised until the monetary loss becomes minimal. The
iterative process therefore determines an optimum conflict resolution
by monitoring the change to the contribution margin. Furthermore, a
monetary value of each dispatching decision can also be derived.
Abstract: In order to produce lead free piezoceramics with
optimum piezoelectric and dielectric properties, KNN modified with
Li+ (as an A site dopant) and Sb5+ (as a B site dopant)
(K0.49Na0.49Li0.02) (Nb0.96Sb0.04) O3 (referred as KNLNS in this paper)
have been synthesized using solid state reaction method and
conventional sintering technique. The ceramics were sintered in the
narrow range of 1050°C-1090°C for 2-3 h to get precise information
about sintering parameters. Detailed study of dependence of
microstructural, dielectric and piezoelectric properties on sintering
conditions was then carried out. The study suggests that the volatility
of the highly hygroscopic KNN ceramics is not only sensitive to
sintering temperatures but also to sintering durations. By merely
reducing the sintering duration for a given sintering temperature we
saw an increase in the density of the samples which was supported by
the increase in dielectric constants of the ceramics. And since density
directly or indirectly affects almost all the associated properties, other
dielectric and piezoelectric properties were also enhanced as we
approached towards the most suitable sintering temperature and
duration combination. The detailed results are reported in this paper.
Abstract: We evaluate the performance of a numerical method
for global optimization of expensive functions. The method is using a
response surface to guide the search for the global optimum. This
metamodel could be based on radial basis functions, kriging, or a
combination of different models. We discuss how to set the cyclic
parameters of the optimization method to get a balance between local
and global search. We also discuss the eventual problem with Runge
oscillations in the response surface.
Abstract: The present study was carried out to investigate the
effect of alloying elements and thermo-mechanical treatment (TMT)
i.e. hot rolling and forging with different reduction ratios on the
hardness (HV) and impact toughness (J) of heat-treated low alloy
steels. An understanding of the combined effect of TMT and alloying
elements and by measuring hardness, impact toughness, resulting
from different heat treatment following TMT of the low alloy steels,
it is possible to determine which conditions yielded optimum
mechanical properties and high strength to weight ratio.
Experimental Correlations between hot work reduction ratio,
hardness and impact toughness for thermo-mechanically heat treated
low alloy steels are analyzed quantitatively, and both regression and
mathematical hardness and impact toughness models are developed.
Abstract: This paper is part of a study to develop robots for
farming. As such power requirement to operate equipment attach to
such robots become an important factor. Soil-tool interaction plays
major role in power consumption, thus predicting accurately the
forces which act on the blade during the farming is very important for
optimal designing of farm equipment. In this paper, a finite element
investigation for tillage tools and soil interaction is described by
using an inelastic constitutive material law for agriculture
application. A 3-dimensional (3D) nonlinear finite element analysis
(FEA) is developed to examine behavior of a blade with different
rake angles moving in a block of soil, and to estimate the blade force.
The soil model considered is an elastic-plastic with non-associated
Drucker-Prager material model. Special use of contact elements are
employed to consider connection between soil-blade and soil-soil
surfaces. The FEA results are compared with experimental ones,
which show good agreement in accurately predicting draft forces
developed on the blade when it moves through the soil. Also a very
good correlation was obtained between FEA results and analytical
results from classical soil mechanics theories for straight blades.
These comparisons verified the FEA model developed. For analyzing
complicated soil-tool interactions and for optimum design of blades,
this method will be useful.
Abstract: A large amount of blast furnace slag is generated in
China. Most ground granulated blast furnace slag (GGBS) however
ends up in low-grade applications. Blast furnace slag, ground to an
appropriate fineness, can be used as a partial replacement of
cementitious material in concrete. The potential for using GGBS in
structural concrete, e.g. concrete beams and columns is investigated
at Xi’an Jiaotong-Liverpool University (XJTLU). With 50% of CEM
I cement replaced with GGBS, peak hydration temperatures
determined in a suspended concrete slab reduced by 20%. This
beneficiary effect has not been further improved with 70% of CEM I
replaced with GGBS. Partial replacement of CEM I with GGBS has a
retardation effect on the early-age strength of concrete. More GGBS
concrete mixes will be conducted to identify an ‘optimum’
replacement level which will lead to a reduced thermal loading,
without significantly compromising the early-age strength of
concrete.
Abstract: The article deals with the tool in Matlab GUI form
that is designed to analyse a mechatronic system sensitivity and
tolerance. In the analysed mechatronic system, a torque is transferred
from the drive to the load through a coupling containing flexible
elements. Different methods of control system design are used. The
classic form of the feedback control is proposed using Naslin method,
modulus optimum criterion and inverse dynamics method. The
cascade form of the control is proposed based on combination of
modulus optimum criterion and symmetric optimum criterion. The
sensitivity is analysed on the basis of absolute and relative sensitivity
of system function to the change of chosen parameter value of the
mechatronic system, as well as the control subsystem. The tolerance
is analysed in the form of determining the range of allowed relative
changes of selected system parameters in the field of system stability.
The tool allows to analyse an influence of torsion stiffness, torsion
damping, inertia moments of the motor and the load and controller(s)
parameters. The sensitivity and tolerance are monitored in terms of
the impact of parameter change on the response in the form of system
step response and system frequency-response logarithmic
characteristics. The Symbolic Math Toolbox for expression of the
final shape of analysed system functions was used. The sensitivity
and tolerance are graphically represented as 2D graph of sensitivity
or tolerance of the system function and 3D/2D static/interactive graph
of step/frequency response.
Abstract: Rice straw is lignocellulosic biomass which can be utilized as substrate for the biogas production. However, due to the property and composition of rice straw, it is difficult to be degraded by hydrolysis enzymes. One of the pretreatment methods that modify such properties of lignocellulosic biomass is the application of lignocellulose-degrading microbial consortia. The aim of this study is to investigate the effect of microbial consortia to enhance biogas production. To select the high efficient consortium, cellulase enzymes were extracted and their activities were analyzed. The results suggested that microbial consortium culture obtained from cattle manure is the best candidate compared to decomposed wood and horse manure. A microbial consortium isolated from cattle manure was then mixed with anaerobic sludge and used as inoculum for biogas production. The optimal conditions for biogas production were investigated using response surface methodology (RSM). The tested parameters were the ratio of amount of microbial consortium isolated and amount of anaerobic sludge (MI:AS), substrate to inoculum ratio (S:I) and temperature. Here, the value of the regression coefficient R2 = 0.7661 could be explained by the model which is high to advocate the significance of the model. The highest cumulative biogas yield was 104.6 ml/g-rice straw at optimum ratio of MI:AS, ratio of S:I, and temperature of 2.5:1, 15:1 and 44°C respectively.
Abstract: Nanofibers are effective materials which have
frequently been investigated to produce high quality air filters. As an
environmental approach our aim is to achieve nanofibers by melting.
In spun-bond systems extruder, spin-pump, nozzle package and
attenuator are used. Molten polymer which flows from extruder is
made steady by spin-pump. Regular melt passes through nozzle holes
and forms fibers under high pressure. The fibers pulled from nozzle
are shrunk to micron size by an attenuator; after solidification, they
are collected on a conveyor. In this research different designs of
attenuator system have been studied; and also CFD analysis has been
done on these different designs. Afterwards, one of these designs
tested and finally some optimizations have been done to reduce
pressure loss and increase air velocity.
Abstract: This paper presents system level CMOS solid-state
nanopore techniques enhancement for speedup next generation
molecular recording and high throughput channels. This discussion
also considers optimum number of base-pair (bp) measurements
through channel as an important role to enhance potential read
accuracy. Effective power consumption estimation offered suitable
range of multi-channel configuration. Nanopore bp extraction model
in statistical method could contribute higher read accuracy with
longer read-length (200 < read-length). Nanopore ionic current
switching with Time Multiplexing (TM) based multichannel readout
system contributed hardware savings.
Abstract: In Jordan having deficit atmospheric precipitation, an
increase in water demand occurs during summer months. Jordan can
be regarded with a relatively high potential for wastewater recycling
and reuse. The main purpose of this paper was to investigate the
removal of total suspended solids (TSS) and chemical oxygen
demand (COD) for olive mill wastewater (OMW) by
electrocoagulation (EC) process. In the combination of
electrocoagulation by using coupled iron–aluminum electrodes, the
optimum working pH was found to be around 6. Results indicated
that the electrocoagulation process allowed removal of TSS and COD
of about 82.5% and 47.5%, respectively at 45 mA/cm2 after 70
minutes by using coupled iron–aluminum electrodes. It was
demonstrated that the maximum TSS and COD removals were
obtained at some optimum experimental parameters for current
density, pH, and reaction time.
Abstract: To determine the potential of a low cost Irish
engineered timber product to replace high cost solid timber for use in
bending active structures such as gridshells a single Irish engineered
timber product in the form of orientated strand board (OSB) was
selected. A comparative study of OSB and solid timber was carried
out to determine the optimum properties that make a material suitable
for use in gridshells. Three parameters were identified to be relevant
in the selection of a material for gridshells. These three parameters
are the strength to stiffness ratio, the flexural stiffness of
commercially available sections, and the variability of material and
section properties. It is shown that when comparing OSB against
solid timber, OSB is a more suitable material for use in gridshells that
are at the smaller end of the scale and that have tight radii of
curvature. Typically, for solid timber materials, stiffness is used as an
indicator for strength and engineered timber is no different. Thus, low
flexural stiffness would mean low flexural strength. However, when
it comes to bending active gridshells, OSB offers a significant
advantage. By the addition of multiple layers, an increased section
size is created, thus endowing the structure with higher stiffness and
higher strength from initial low stiffness and low strength materials
while still maintaining tight radii of curvature. This allows OSB to
compete with solid timber on large scale gridshells. Additionally, a
preliminary sustainability study using a set of sustainability indicators
was carried out to determine the relative sustainability of building a
large-scale gridshell in Ireland with a primary focus on economic
viability but a mention is also given to social and environmental
aspects. For this, the Savill garden gridshell in the UK was used as
the functional unit with the sustainability of the structural roof
skeleton constructed from UK larch solid timber being compared
with the same structure using Irish OSB. Albeit that the advantages of
using commercially available OSB in a bending active gridshell are
marginal and limited to specific gridshell applications, further study
into an optimised engineered timber product is merited.
Abstract: Nitrogen fertilizer is the most used and often the most
mismanaged nutrient input. Nitrogen management has tremendous
implications on crop productivity, quality and environmental
stewardship. Sufficient nitrogen is needed to optimum yield and
quality. Soil and in-season plant tissue testing for nitrogen status are
a time consuming and expensive process. Real time sensing of plant
nitrogen status can be a useful tool in managing nitrogen inputs. The
objectives of this project were to assess the reliability of remotely
sensed non-destructive plant nitrogen measurements compared to wet
chemistry data from sampled plant tissue, develop in-season nitrogen
recommendations based on remotely sensed data for improved
nitrogen use efficiency and assess the potential for determining yield
and quality from remotely sensed data. Very good correlations were
observed between early-season remotely sensed crop nitrogen status
and plant nitrogen concentrations and subsequent in-season fertilizer
recommendations. The transmittance/absorbance type meters gave
the most accurate readings. Early in-season fertilizer recommendation
would be to apply 40 kg nitrogen per hectare plus 15 kg nitrogen per
hectare for each unit difference measured with the SPAD meter
between the crop and reference area or 25 kg plus 13 kg per hectare
for each unit difference measured with the CCM 200. Once the crop
was sufficiently fertilized meter readings became inconclusive and
were of no benefit for determining nitrogen status, silage yield and
quality and grain yield and protein.
Abstract: Power Regeneration in Refrigeration Plant concept
has been analyzed and has been shown to be capable of saving about
25% power in Cryogenic Plants with the Power Regeneration System
(PRS) running under nominal conditions. The innovative component
Compressor Expander Group (CEG) based on turbomachinery has
been designed and built modifying CETT compressor and expander,
both selected for optimum plant performance. Experiments have
shown the good response of the turbomachines to run with R404a as
working fluid. Power saving up to 12% under PRS derated conditions
(50% loading) has been demonstrated. Such experiments allowed
predicting a power saving up to 25% under CEG full load.
Abstract: This paper discusses the design and analysis of a
hybrid PV-Fuel cell energy system destined to power a DC load. The
system is composed of a photovoltaic array, a fuel cell, an
electrolyzer and a hydrogen tank. HOMER software is used in this
study to calculate the optimum capacities of the power system
components that their combination allows an efficient use of solar
resource to cover the hourly load needs. The optimal system sizing
allows establishing the right balance between the daily electrical
energy produced by the power system and the daily electrical energy
consumed by the DC load using a 28 KW PV array, a 7.5 KW fuel
cell, a 40KW electrolyzer and a 270 Kg hydrogen tank. The variation
of powers involved into the DC bus of the hybrid PV-fuel cell system
has been computed and analyzed for each hour over one year: the
output powers of the PV array and the fuel cell, the input power of
the elctrolyzer system and the DC primary load. Equally, the annual
variation of stored hydrogen produced by the electrolyzer has been
assessed. The PV array contributes in the power system with 82%
whereas the fuel cell produces 18%. 38% of the total energy
consumption belongs to the DC primary load while the rest goes to
the electrolyzer.
Abstract: In this research paper were investigated the main
regularities of a radical bromination reaction of decalin. There had
been studied the temperature effect, durations of reaction, frequency
rate of process, a ratio of initial components, type and number of the
initiator on decalin bromination degree.
There were specified optimum conditions of synthesis of a
perbromodecalin by the method of a decalin bromination. There are
developed the technological flowchart of receiving a
perbromodecalin and the mass balance of process on the first and the
subsequent loadings of components.
The results of research of antibacterial and antifungal activity of
synthesized bromoderivatives have been represented.
Abstract: The turbocharger and turbocharging have been the
inherent component of diesel engines, so that critical parameters of
such engines, as BSFC (Brake Specific Fuel Consumption) or
thermal efficiency, fuel consumption, BMEP (Brake Mean Effective
Pressure), the power density output and emission level have been
improved extensively. In general, the turbocharger can be considered
as the most complex component of diesel engines, because it has
closely interrelated turbomachinery concepts of the turbines and the
compressors to thermodynamic fundamentals of internal combustion
engines and stress analysis of all components.
In this paper, a waste gate for a conventional single stage radial
turbine is investigated by consideration of turbochargers operation
constrains and engine operation conditions, without any detail
designs in the turbine and the compressor. Amount of opening waste
gate which extended between the ranges of full opened and closed
valve, is demonstrated by limiting compressor boost pressure ratio.
Obtaining of an optimum point by regard above mentioned items is
surveyed by three linked meanline modeling programs together
which consist of Turbomatch®, Compal®, Rital® madules in concepts
NREC® respectively.
Abstract: Ti6Al4V alloy is highly used in the automotive and
aerospace industry due to its good machining characteristics. Micro
EDM drilling is commonly used to drill micro hole on extremely hard
material with very high depth to diameter ratio. In this study, the
parameters of micro-electrical discharge machining (EDM) in drilling
of Ti6Al4V alloy is optimized for higher machining accuracy with
less hole-dilation and hole taper ratio. The micro-EDM machining
parameters includes, peak current and pulse on time. Fuzzy analysis
was developed to evaluate the machining accuracy. The analysis
shows that hole-dilation and hole-taper ratio are increased with the
increasing of peak current and pulse on time. However, the surface
quality deteriorates as the peak current and pulse on time increase.
The combination that gives the optimum result for hole dilation is
medium peak current and short pulse on time. Meanwhile, the
optimum result for hole taper ratio is low peak current and short pulse
on time.
Abstract: Maize constitutes a major agrarian production for use
by the vast population but despite its economic importance; it has not
been produced to meet the economic needs of the country. Achieving
optimum yield in maize can meaningfully be supported by land
suitability analysis in order to guarantee self-sufficiency for future
production optimization. This study examines land suitability for
maize production through the analysis of the physicochemical
variations in soil properties and other land attributes over space using
a Geographic Information System (GIS) framework.
Physicochemical parameters of importance selected include slope,
landuse, physical and chemical properties of the soil, and climatic
variables. Landsat imagery was used to categorize the landuse,
Shuttle Radar Topographic Mapping (SRTM) generated the slope and
soil samples were analyzed for its physical and chemical components.
Suitability was categorized into highly, moderately and marginally
suitable based on Food and Agricultural Organisation (FAO)
classification, using the Analytical Hierarchy Process (AHP)
technique of GIS. This result can be used by small scale farmers for
efficient decision making in the allocation of land for maize
production.
Abstract: The wide use of the Internet-based applications bring many challenges to the researchers to guarantee the continuity of the connections needed by the mobile hosts and provide reliable Internet access for them. One of proposed solutions by Internet Engineering Task Force (IETF) is to connect the local, multi-hop, and infrastructure-less Mobile Ad hoc Network (MANET) with Internet structure. This connection is done through multi-interface devices known as Internet Gateways. Many issues are related to this connection like gateway discovery, handoff, address auto-configuration and selecting the optimum gateway when multiple gateways exist. Many studies were done proposing gateway selection schemes with a single selection criterion or weighted multiple criteria. In this research, a review of some of these schemes is done showing the differences, the features, the challenges and the drawbacks of each of them.