Abstract: This paper considers the problem of finding low cost
chip set for a minimum cost partitioning of a large logic circuits. Chip
sets are selected from a given library. Each chip in the library has a
different price, area, and I/O pin. We propose a low cost chip set
selection algorithm. Inputs to the algorithm are a netlist and a chip
information in the library. Output is a list of chip sets satisfied with
area and maximum partitioning number and it is sorted by cost. The
algorithm finds the sorted list of chip sets from minimum cost to
maximum cost. We used MCNC benchmark circuits for experiments.
The experimental results show that all of chip sets found satisfy the
multiple partitioning constraints.
Abstract: Experiments have been carried out at sub-critical
Reynolds number to investigate free-to-roll motions induced by
forebody and/or wings complex flow on a 30° swept back nonslender
wings-slender body-model for static and dynamic (pitch-up)
cases. For the dynamic (pitch-up) case it has been observed that roll
amplitude decreases and lag increases with increase in pitching
speed. Decrease in roll amplitude with increase in pitch rate is
attributed to low disturbing rolling moment due to weaker interaction
between forebody and wing flow components. Asymmetric forebody
vortices dominate and control the roll motion of the model in
dynamic case when non-dimensional pitch rate ≥ 1x10-2.
Effectiveness of the active control scheme utilizing rotating nose with
artificial tip perturbation is observed to be low in the angle of attack
region where the complex flow over the wings has contributions from
both forebody and wings.
Abstract: This paper proposes a new solution to string matching problem. This solution constructs an inverted list representing a string pattern to be searched for. It then uses a new algorithm to process an input string in a single pass. The preprocessing phase takes 1) time complexity O(m) 2) space complexity O(1) where m is the length of pattern. The searching phase time complexity takes 1) O(m+α ) in average case 2) O(n/m) in the best case and 3) O(n) in the worst case, where α is the number of comparing leading to mismatch and n is the length of input text.
Abstract: In this paper, an accurate theoretical analysis for the achievable average channel capacity (in the Shannon sense) per user of a hybrid cellular direct-sequence/fast frequency hopping code-division multiple-access (DS/FFH-CDMA) system operating in a Rayleigh fading environment is presented. The analysis covers the downlink operation and leads to the derivation of an exact mathematical expression between the normalized average channel capacity available to each system-s user, under simultaneous optimal power and rate adaptation and the system-s parameters, as the number of hops per bit, the processing gain applied, the number of users per cell and the received signal-tonoise power ratio over the signal bandwidth. Finally, numerical results are presented to illustrate the proposed mathematical analysis.
Abstract: A learning management system (commonly
abbreviated as LMS) is a software application for the administration,
documentation, tracking, and reporting of training programs,
classroom and online events, e-learning programs, and training
content (Ellis 2009). (Hall 2003) defines an LMS as \"software that
automates the administration of training events. All Learning
Management Systems manage the log-in of registered users, manage
course catalogs, record data from learners, and provide reports to
management\". Evidence of the worldwide spread of e-learning in
recent years is easy to obtain. In April 2003, no fewer than 66,000
fully online courses and 1,200 complete online programs were listed
on the TeleCampus portal from TeleEducation (Paulsen 2003). In the
report \" The US market in the Self-paced eLearning Products and
Services:2010-2015 Forecast and Analysis\" The number of student
taken classes exclusively online will be nearly equal (1% less) to the
number taken classes exclusively in physical campuses. Number of
student taken online course will increase from 1.37 million in 2010 to
3.86 million in 2015 in USA. In another report by The Sloan
Consortium three-quarters of institutions report that the economic
downturn has increased demand for online courses and programs.
Abstract: The broadcast problem including the plan design is
considered. The data are inserted and numbered at predefined order
into customized size relations. The server ability to create a full,
regular Broadcast Plan (RBP) with single and multiple channels after
some data transformations is examined. The Regular Geometric
Algorithm (RGA) prepares a RBP and enables the users to catch their
items avoiding energy waste of their devices. Moreover, the
Grouping Dimensioning Algorithm (GDA) based on integrated
relations can guarantee the discrimination of services with a
minimum number of channels. This last property among the selfmonitoring,
self-organizing, can be offered by servers today
providing also channel availability and less energy consumption by
using smaller number of channels. Simulation results are provided.
Abstract: In this paper, the statistical properties of filtered or convolved signals are considered by deriving the resulting density functions as well as the exact mean and variance expressions given a prior knowledge about the statistics of the individual signals in the filtering or convolution process. It is shown that the density function after linear convolution is a mixture density, where the number of density components is equal to the number of observations of the shortest signal. For circular convolution, the observed samples are characterized by a single density function, which is a sum of products.
Abstract: The main focus of the work was concerned with hydrodynamic and thermal analysis of the plate heat exchanger channel with corrugation patterns suggested to be triangular, sinusoidal, and square corrugation. This study was to numerically model and validate the triangular corrugated channel with dimensions/parameters taken from open literature, and then model/analyze both sinusoidal, and square corrugated channel referred to the triangular model. Initially, 2D modeling with local extensive analysis for triangular corrugated channel was carried out. By that, all local pressure drop, wall shear stress, friction factor, static temperature, heat flux, Nusselt number, and surface heat coefficient, were analyzed to interpret the hydrodynamic and thermal phenomena occurred in the flow. Furthermore, in order to facilitate confidence in this model, a comparison between the values predicted, and experimental results taken from literature for almost the same case, was done. Moreover, a holistic numerical study for sinusoidal and square channels together with global comparisons with triangular corrugation under the same condition, were handled. Later, a comparison between electric, and fluid cooling through varying the boundary condition was achieved. The constant wall temperature and constant wall heat flux boundary conditions were employed, and the different resulted Nusselt numbers as a consequence were justified. The results obtained can be used to come up with an optimal design, a 'compromise' between heat transfer and pressure drop.
Abstract: Two-dimensional Direct Numerical Simulation (DNS)
of high Schmidt number mass transfer in a convective flow environment
(Rayleigh-B'enard) is carried out and results are compared to
experimental data. A fourth-order accurate WENO-scheme has been
used for scalar transport in order to aim for a high accuracy in areas
of high concentration gradients. It was found that the typical spatial
distance between downward plumes of cold high concentration water
and the eddy size are in good agreement with experiments using a
combined PIV-LIF technique for simultaneous and spatially synoptic
measurements of 2D velocity and concentration fields.
Abstract: The objective of this study was to improve our
understanding of vulnerability and environmental change; it's causes
basically show the intensity, its distribution and human-environment
effect on the ecosystem in the Apodi Valley Region, This paper is
identify, assess and classify vulnerability and environmental change
in the Apodi valley region using a combined approach of landscape
pattern and ecosystem sensitivity. Models were developed using the
following five thematic layers: Geology, geomorphology, soil,
vegetation and land use/cover, by means of a Geographical
Information Systems (GIS)-based on hydro-geophysical parameters.
In spite of the data problems and shortcomings, using ESRI-s ArcGIS
9.3 program, the vulnerability score, to classify, weight and combine
a number of 15 separate land cover classes to create a single indicator
provides a reliable measure of differences (6 classes) among regions
and communities that are exposed to similar ranges of hazards.
Indeed, the ongoing and active development of vulnerability
concepts and methods have already produced some tools to help
overcome common issues, such as acting in a context of high
uncertainties, taking into account the dynamics and spatial scale of
asocial-ecological system, or gathering viewpoints from different
sciences to combine human and impact-based approaches. Based on
this assessment, this paper proposes concrete perspectives and
possibilities to benefit from existing commonalities in the
construction and application of assessment tools.
Abstract: Indoor air distribution has great impact on people-s thermal sensation. Therefore, how to remove the indoor excess heat becomes an important issue to create a thermally comfortable indoor environment. To expel the extra indoor heat effectively, this paper used a dynamic CFD approach to study the effect of an air-supply guide vane swinging periodically on the indoor air distribution within a model room. The numerical results revealed that the indoor heat transfer performance caused by the swing guide vane had close relation with the number of vortices developing under the inlet cold jet. At larger swing amplitude, two smaller vortices continued to shed outward under the cold jet and remove the indoor heat load more effectively. As a result, it can be found that the average Nusselt number on the floor increased with the increase of the swing amplitude of the guide vane.
Abstract: In this work we adopt a combination of Laplace
transform and the decomposition method to find numerical solutions
of a system of multi-pantograph equations. The procedure leads to a
rapid convergence of the series to the exact solution after computing a
few terms. The effectiveness of the method is demonstrated in some
examples by obtaining the exact solution and in others by computing
the absolute error which decreases as the number of terms of the series
increases.
Abstract: Cyber physical system (CPS) for target tracking, military surveillance, human health monitoring, and vehicle detection all require maximizing the utility and saving the energy. Sensor selection is one of the most important parts of CPS. Sensor selection problem (SSP) is concentrating to balance the tradeoff between the number of sensors which we used and the utility which we will get. In this paper, we propose a performance constrained slide windows (PCSW) based algorithm for SSP in CPS. we present results of extensive simulations that we have carried out to test and validate the PCSW algorithms when we track a target, Experiment shows that the PCSW based algorithm improved the performance including selecting time and communication times for selecting.
Abstract: The study was carried out to evaluated effect of S-gridling on fruit growth and quality of wax apple. The study was laid in Random completed block design with four replicated. Four treatment were applied as follows: S-girdling, fruit thinning plus bagging with 2,4-D sprayed, fruit thinning plus bagging and the control treatment. 2,4D was sprayed at the small bud and petal fall stage. Girdling was applied three week before flowering. The effect of all treatments on fruit growth was measured weekly. Number of flower, fruit set, fruit drop, fruit crack, and fruit quality were recorded. The result indicated that S-girdling, 2,4D application produced the lowest bud drop, fruit drop compared to untreated control. S-girdling improved faster fruit growth producing the best final fruit length and diameter compared to untreated control. S-girdling also markedly enhanced fruit set, fruit weight, and total soluble solid, reduced fruit crack, titratable acidity. On the other hand, it was noticed that with 2,4-D application also increased the fruit growth rate, improved physiological and biochemical characters of fruit than control treatment. It was concluded that S-girdling was recommended as the industry norm to increase fruit set, fruit quality in wax apple. 2,4D application had a distinctive and significant effect on most of the fruit quality characteristics assessed.
Abstract: Road crashes not only claim lives and inflict injuries but also create economic burden to the society due to loss of productivity. The problem of deaths and injuries as a result of road traffic crashes is now acknowledged to be a global phenomenon with authorities in virtually all countries of the world concerned about the growth in the number of people killed and seriously injured on their roads. However, the road crash scenario of a developing country like Bangladesh is much worse comparing with this of developed countries. For developing proper countermeasures it is necessary to identify the factors affecting crash occurrences. The objectives of the study is to examine the effect of district wise road infrastructure, socioeconomic and demographic features on crash occurrence .The unit of analysis will be taken as individual district which has not been explored much in the past. Reported crash data obtained from Bangladesh Road Transport Authority (BRTA) from the year 2004 to 2010 are utilized to develop negative binomial model. The model result will reveal the effect of road length (both paved and unpaved), road infrastructure and several socio economic characteristics on district level crash frequency in Bangladesh.
Abstract: This paper tries to represent a new method for
computing the reliability of a system which is arranged in series or
parallel model. In this method we estimate life distribution function
of whole structure using the asymptotic Extreme Value (EV)
distribution of Type I, or Gumbel theory. We use EV distribution in
minimal mode, for estimate the life distribution function of series
structure and maximal mode for parallel system. All parameters also
are estimated by Moments method. Reliability function and failure
(hazard) rate and p-th percentile point of each function are
determined. Other important indexes such as Mean Time to Failure
(MTTF), Mean Time to repair (MTTR), for non-repairable and
renewal systems in both of series and parallel structure will be
computed.
Abstract: A new design of a planar passive T-micromixer with fin-shaped baffles in the mixing channel is presented. The mixing efficiency and the level of pressure loss in the channel have been investigated by numerical simulations in the range of Reynolds number (Re) 1 to 50. A Mixing index (Mi) has been defined to quantify the mixing efficiency, which results over 85% at both ends of the Re range, what demonstrates the micromixer can enhance mixing using the mechanisms of diffusion (lower Re) and convection (higher Re). Three geometric dimensions: radius of baffle, baffles pitch and height of the channel define the design parameters, and the mixing index and pressure loss are the performance parameters used to optimize the micromixer geometry with a multi-criteria optimization method. The Pareto front of designs with the optimum trade-offs, maximum mixing index with minimum pressure loss, is obtained. Experiments for qualitative and quantitative validation have been implemented.
Abstract: Disordered function of maniphalanx and difficulty with
ambulation will occur insofar as a human has a failure in the spinal
marrow. Cervical spondylotic myelopathy as one of the myelopathy
emanates from not only external factors but also increased age. In
addition, the diacrisis is difficult since cervical spondylotic
myelopathy is evaluated by a doctor-s neurological remark and
imaging findings. As a quantitative method for measuring the degree
of disability, hand-operated triangle step test (for short, TST) has
formulated. In this research, a full automatic triangle step counter
apparatus is designed and developed to measure the degree of
disability in an accurate fashion according to the principle of TST. The
step counter apparatus whose shape is a low triangle pole displays the
number of stepping upon each corner. Furthermore, the apparatus has
two modes of operation. Namely, one is for measuring the degree of
disability and the other for rehabilitation exercise. In terms of
usefulness, clinical practice should be executed before too long.
Abstract: Certifications such as the Passive House Standard aim to reduce the final space heating energy demand of residential buildings. Space conditioning, notably heating, is responsible for nearly 70% of final residential energy consumption in Europe. There is therefore significant scope for the reduction of energy consumption through improvements to the energy efficiency of residential buildings. However, these certifications totally overlook the energy embodied in the building materials used to achieve this greater operational energy efficiency. The large amount of insulation and the triple-glazed high efficiency windows require a significant amount of energy to manufacture. While some previous studies have assessed the life cycle energy demand of passive houses, including their embodied energy, these rely on incomplete assessment techniques which greatly underestimate embodied energy and can lead to misleading conclusions. This paper analyses the embodied and operational energy demands of a case study passive house using a comprehensive hybrid analysis technique to quantify embodied energy. Results show that the embodied energy is much more significant than previously thought. Also, compared to a standard house with the same geometry, structure, finishes and number of people, a passive house can use more energy over 80 years, mainly due to the additional materials required. Current building energy efficiency certifications should widen their system boundaries to include embodied energy in order to reduce the life cycle energy demand of residential buildings.
Abstract: This paper proposes the application of a hierarchical fuzzy system (HFS) based on multi-input power system stabilizer (MPSS) and also Static Var Compensator (SVC) in multi-machine environment.The number of rules grows exponentially with the number of variables in a conventional fuzzy logic system. The proposed HFS method is developed to solve this problem. To reduce the number of rules the HFS consists of a number of low-dimensional fuzzy systems in a hierarchical structure. In fact, by using HFS the total number of involved rules increases only linearly with the number of input variables. In the MPSS, to have better efficiency an auxiliary signal of reactive power deviation (ΔQ) is added with ΔP+ Δω input type Power system stabilizer (PSS). Phasor model of SVC is described and used in this paper. The performances of MPSS, Conventional power system stabilizer (CPSS), hierarchical Fuzzy Multi-input Power System Stabilizer (HFMPSS) and the proposed method in damping inter-area mode of oscillation are examined in response to disturbances. By using digital simulations the comparative study is illustrated. It can be seen that the proposed PSS is performing satisfactorily within the whole range of disturbances.