Abstract: Fluids are used for heat transfer in many engineering
equipments. Water, ethylene glycol and propylene glycol are some
of the common heat transfer fluids. Over the years, in an attempt to
reduce the size of the equipment and/or efficiency of the process,
various techniques have been employed to improve the heat transfer
rate of these fluids. Surface modification, use of inserts and
increased fluid velocity are some examples of heat transfer
enhancement techniques. Addition of milli or micro sized particles
to the heat transfer fluid is another way of improving heat transfer
rate. Though this looks simple, this method has practical problems
such as high pressure loss, clogging and erosion of the material of
construction. These problems can be overcome by using nanofluids,
which is a dispersion of nanosized particles in a base fluid.
Nanoparticles increase the thermal conductivity of the base fluid
manifold which in turn increases the heat transfer rate. In this work,
the heat transfer enhancement using aluminium oxide nanofluid has
been studied by computational fluid dynamic modeling of the
nanofluid flow adopting the single phase approach.
Abstract: In the urban traffic network, the intersections are the
“bottleneck point" of road network capacity. And the arterials are the
main body in road network and the key factor which guarantees the
normal operation of the city-s social and economic activities. The
rapid increase in vehicles leads to seriously traffic jam and cause the
increment of vehicles- delay. Most cities of our country are
traditional single control system, which cannot meet the need for the
city traffic any longer. In this paper, Synchro6.0 as a platform to
minimize the intersection delay, optimizesingle signal cycle and split
for Zhonghua Street in Handan City. Meanwhile, linear control
system uses to optimize the phase for the t arterial road in this
system. Comparing before and after use the control, capacities and
service levels of this road and the adjacent road have improved
significantly.
Abstract: The mineral having chemical compositional formula MgAl2O4 is called “spinel". The ferrites crystallize in spinel structure are known as spinel-ferrites or ferro-spinels. The spinel structure has a fcc cage of oxygen ions and the metallic cations are distributed among tetrahedral (A) and octahedral (B) interstitial voids (sites). The X-ray diffraction (XRD) intensity of each Bragg plane is sensitive to the distribution of cations in the interstitial voids of the spinel lattice. This leads to the method of determination of distribution of cations in the spinel oxides through XRD intensity analysis. The computer program for XRD intensity analysis has been developed in C language and also tested for the real experimental situation by synthesizing the spinel ferrite materials Mg0.6Zn0.4AlxFe2- xO4 and characterized them by X-ray diffractometry. The compositions of Mg0.6Zn0.4AlxFe2-xO4(x = 0.0 to 0.6) ferrites have been prepared by ceramic method and powder X-ray diffraction patterns were recorded. Thus, the authenticity of the program is checked by comparing the theoretically calculated data using computer simulation with the experimental ones. Further, the deduced cation distributions were used to fit the magnetization data using Localized canting of spins approach to explain the “recovery" of collinear spin structure due to Al3+ - substitution in Mg-Zn ferrites which is the case if A-site magnetic dilution and non-collinear spin structure. Since the distribution of cations in the spinel ferrites plays a very important role with regard to their electrical and magnetic properties, it is essential to determine the cation distribution in spinel lattice.
Abstract: This paper proposes a prototype of a lower-limb
rehabilitation system for recovering and strengthening patients-
injured lower limbs. The system is composed of traction motors for
each leg position, a treadmill as a walking base, tension sensors,
microcontrollers controlling motor functions and a main system with
graphic user interface. For derivation of reference or normal velocity
profiles of the body segment point, kinematic method is applied based
on the humanoid robot model using the reference joint angle data of
normal walking.
Abstract: In this paper, the discrete-time fuzzy BAM neural network with delays and impulses is studied. Sufficient conditions are obtained for the existence and global stability of a unique equilibrium of this class of fuzzy BAM neural networks with Lipschitzian activation functions without assuming their boundedness, monotonicity or differentiability and subjected to impulsive state displacements at fixed instants of time. Some numerical examples are given to demonstrate the effectiveness of the obtained results.
Abstract: Perth will run out of available sustainable natural
water resources by 2015 if nothing is done to slow usage rates,
according to a Western Australian study [1]. Alternative water
technology options need to be considered for the long-term
guaranteed supply of water for agricultural, commercial, domestic
and industrial purposes. Seawater is an alternative source of water for
human consumption, because seawater can be desalinated and
supplied in large quantities to a very high quality.
While seawater desalination is a promising option, the technology
requires a large amount of energy which is typically generated from
fossil fuels. The combustion of fossil fuels emits greenhouse gases
(GHG) and, is implicated in climate change. In addition to
environmental emissions from electricity generation for desalination,
greenhouse gases are emitted in the production of chemicals and
membranes for water treatment. Since Australia is a signatory to the
Kyoto Protocol, it is important to quantify greenhouse gas emissions
from desalinated water production.
A life cycle assessment (LCA) has been carried out to determine
the greenhouse gas emissions from the production of 1 gigalitre (GL)
of water from the new plant. In this LCA analysis, a new desalination
plant that will be installed in Bunbury, Western Australia, and known
as Southern Seawater Desalinization Plant (SSDP), was taken as a
case study. The system boundary of the LCA mainly consists of three
stages: seawater extraction, treatment and delivery. The analysis
found that the equivalent of 3,890 tonnes of CO2 could be emitted
from the production of 1 GL of desalinated water. This LCA analysis
has also identified that the reverse osmosis process would cause the
most significant greenhouse emissions as a result of the electricity
used if this is generated from fossil fuels
Abstract: Wastages such as grated coconut meat, spent tea and used sugarcane had contributed negative impacts to the environment. Vermicomposting method is fully utilized to manage the wastes towards a more sustainable approach. The worms that are used in the vermicomposting are Eisenia foetida and Eudrillus euginae. This research shows that the vermicompost of wastages has voltage of electrical energy and is able to light up the Light-Emitting Diode (LED) device. Based on the experiment, the use of replicated and double compartments of the component will produce double of voltage. Hence, for conclusion, this harmless and low cost technology of vermicompost can act as a dry cell in order to reduce the usage of hazardous chemicals that can contaminate the environment.
Abstract: Network management techniques have long been of
interest to the networking research community. The queue size plays
a critical role for the network performance. The adequate size of the
queue maintains Quality of Service (QoS) requirements within
limited network capacity for as many users as possible. The
appropriate estimation of the queuing model parameters is crucial for
both initial size estimation and during the process of resource
allocation. The accurate resource allocation model for the
management system increases the network utilization. The present
paper demonstrates the results of empirical observation of memory
allocation for packet-based services.
Abstract: In this paper the main objective is to analyze the
quality of service of the bus companies operating in the city of
Campos, located in the state of Rio de Janeiro, Brazil. This analysis,
based on the opinion of the bus customers, will help to determine
their degree of satisfaction with the service provided by the bus
companies. The result of this assessment shows that the bus
customers are displeased with the quality of service supplied by the
bus companies. Therefore, it is necessary to identify alternative
solutions to minimize the consequences of the main problems related
to customers- dissatisfaction identified in our evaluation and to help
the bus companies operating in Campos better fulfill their riders-
needs.
Abstract: A spectrophotometric method was developed for simultaneous quantification of pseudoephedrine hydrochloride (PSE) triprolidine hydrochloride (TRI) using second derivative method (zero-crossing technique). The second derivative amplitudes of PSE and TRI were measured at 271 and 321 nm, respectively. The calibration curves were linear in the range of 200 to 1,000 g/ml for PSE and 10 to 50 g/ml for TRI. The method was validated for specificity, accuracy, precision, limit of detection and limit of quantitation. The proposed method was applied to the assaying and dissolution of PSE and TRI in commercial tablets without any chemical separation. The results were compared with those obtained by the official USP31 method and statistical tests showed that there is no significant between the methods at 95% confidence level. The proposed method is simple, rapid and suitable for the routine quality control application. KeywordsTriprolidine, Pseudoephedrine, Derivative spectrophotometry, Dissolution testing.
Abstract: The continuity in the electric supply of the electric installations is becoming one of the main requirements of the electric supply network (generation, transmission, and distribution of the electric energy). The achievement of this requirement depends from one side on the structure of the electric network and on the other side on the avaibility of the reserve source provided to maintain the supply in case of failure of the principal one. The avaibility of supply does not only depends on the reliability parameters of the both sources (principal and reserve) but it also depends on the reliability of the circuit breaker which plays the role of interlocking the reserve source in case of failure of the principal one. In addition, the principal source being under operation, its control can be ideal and sure, however, for the reserve source being in stop, a preventive maintenances which proceed on time intervals (periodicity) and for well defined lengths of time are envisaged, so that this source will always available in case of the principal source failure. The choice of the periodicity of preventive maintenance of the source of reserve influences directly the reliability of the electric feeder system In this work and on the basis of the semi- markovian's processes, the influence of the time of interlocking the reserve source upon the reliability of an industrial electric network is studied and is given the optimal time of interlocking the reserve source in case of failure the principal one, also the influence of the periodicity of the preventive maintenance of the source of reserve is studied and is given the optimal periodicity.
Abstract: Batch adsorption of recalcitrant melanoidin using the abundantly available coal fly ash was carried out. It had low specific surface area (SBET) of 1.7287 m2/g and pore volume of 0.002245 cm3/g while qualitative evaluation of the predominant phases in it was done by XRD analysis. Colour removal efficiency was found to be dependent on various factors studied. Maximum colour removal was achieved around pH 6, whereas increasing sorbent mass from 10g/L to 200 g/L enhanced colour reduction from 25% to 86% at 298 K. Spontaneity of the process was suggested by negative Gibbs free energy while positive values for enthalpy change showed endothermic nature of the process. Non-linear optimization of error functions resulted in Freundlich and Redlich-Peterson isotherms describing sorption equilibrium data best. The coal fly ash had maximum sorption capacity of 53 mg/g and could thus be used as a low cost adsorbent in melanoidin removal.
Abstract: This paper presents Genetic Algorithm (GA) based
approach for the allocation of FACTS (Flexible AC Transmission
System) devices for the improvement of Power transfer capacity in an
interconnected Power System. The GA based approach is applied on
IEEE 30 BUS System. The system is reactively loaded starting from
base to 200% of base load. FACTS devices are installed in the
different locations of the power system and system performance is
noticed with and without FACTS devices. First, the locations, where
the FACTS devices to be placed is determined by calculating active
and reactive power flows in the lines. Genetic Algorithm is then
applied to find the amount of magnitudes of the FACTS devices. This
approach of GA based placement of FACTS devices is tremendous
beneficial both in terms of performance and economy is clearly
observed from the result obtained.
Abstract: The Aggregate Production Plan (APP) is a schedule of
the organization-s overall operations over a planning horizon to
satisfy demand while minimizing costs. It is the baseline for any
further planning and formulating the master production scheduling,
resources, capacity and raw material planning. This paper presents a
methodology to model the Aggregate Production Planning problem,
which is combinatorial in nature, when optimized with Genetic
Algorithms. This is done considering a multitude of constraints of
contradictory nature and the optimization criterion – overall cost,
made up of costs with production, work force, inventory, and
subcontracting. A case study of substantial size, used to develop the
model, is presented, along with the genetic operators.
Abstract: This research aims to study the lead pollution in the air of Babylon governorate that resulted generally from vehicles exhausts in addition to industrial and human activities.Vehicles number in Babylon governorate increased significantly after year 2003 that resulted with increase in lead emissions into the air.Measurement of lead emissions was done in seven stations distributed randomly in Babylon governorate. These stations where located in Industrial (Al-Sena'ay) Quarter, 60 street (near to Babylon sewer directorate), 40 Street (near to the first intersection), Al-Hashmia city, Al-Mahaweel city, , Al- Musayab city in addition to another station in Sayd Idris village belong to Abugharaq district (Agricultural station for comparison). The measured concentrations in these stations were compared with the standard limits of Environmental Protection Agency EPA (2 μg /m3). The results of this study showed that the average of lead concentrations ,in Babylon governorate during year 2010, was (3.13 μg/m3) which was greater than standard limits (2 μg/m3). The maximum concentration of lead was (6.41 μg / m3) recorded in the Industrial (Al-Sena'ay) Quarter during April month, while the minimum concentrations was (0.36 μg / m3) recorded in the agricultural station (Abugharaq) during December month.
Abstract: The paper investigates the potential of support vector
machines and Gaussian process based regression approaches to
model the oxygen–transfer capacity from experimental data of
multiple plunging jets oxygenation systems. The results suggest the
utility of both the modeling techniques in the prediction of the
overall volumetric oxygen transfer coefficient (KLa) from operational
parameters of multiple plunging jets oxygenation system. The
correlation coefficient root mean square error and coefficient of
determination values of 0.971, 0.002 and 0.945 respectively were
achieved by support vector machine in comparison to values of
0.960, 0.002 and 0.920 respectively achieved by Gaussian process
regression. Further, the performances of both these regression
approaches in predicting the overall volumetric oxygen transfer
coefficient was compared with the empirical relationship for multiple
plunging jets. A comparison of results suggests that support vector
machines approach works well in comparison to both empirical
relationship and Gaussian process approaches, and could successfully
be employed in modeling oxygen-transfer.
Abstract: Fischer-Tropsch synthesis is one of the most
important catalytic reactions that convert the synthetic gas to light
and heavy hydrocarbons. One of the main issues is selecting the type
of reactor. The slurry bubble reactor is suitable choice for Fischer-
Tropsch synthesis because of its good qualification to transfer heat
and mass, high durability of catalyst, low cost maintenance and
repair. The more common catalysts for Fischer-Tropsch synthesis are
Iron-based and Cobalt-based catalysts, the advantage of these
catalysts on each other depends on which type of hydrocarbons we
desire to produce. In this study, Fischer-Tropsch synthesis is modeled
with Iron and Cobalt catalysts in a slurry bubble reactor considering
mass and momentum balance and the hydrodynamic relations effect
on the reactor behavior. Profiles of reactant conversion and reactant
concentration in gas and liquid phases were determined as the
functions of residence time in the reactor. The effects of temperature,
pressure, liquid velocity, reactor diameter, catalyst diameter, gasliquid
and liquid-solid mass transfer coefficients and kinetic
coefficients on the reactant conversion have been studied. With 5%
increase of liquid velocity (with Iron catalyst), H2 conversions
increase about 6% and CO conversion increase about 4%, With 8%
increase of liquid velocity (with Cobalt catalyst), H2 conversions
increase about 26% and CO conversion increase about 4%. With
20% increase of gas-liquid mass transfer coefficient (with Iron
catalyst), H2 conversions increase about 12% and CO conversion
increase about 10% and with Cobalt catalyst H2 conversions increase
about 10% and CO conversion increase about 6%. Results show that
the process is sensitive to gas-liquid mass transfer coefficient and
optimum condition operation occurs in maximum possible liquid
velocity. This velocity must be more than minimum fluidization
velocity and less than terminal velocity in such a way that avoid
catalysts particles from leaving the fluidized bed.
Abstract: In this paper, an accurate theoretical analysis for the achievable average channel capacity (in the Shannon sense) per user of a hybrid cellular direct-sequence/fast frequency hopping code-division multiple-access (DS/FFH-CDMA) system operating in a Rayleigh fading environment is presented. The analysis covers the downlink operation and leads to the derivation of an exact mathematical expression between the normalized average channel capacity available to each system-s user, under simultaneous optimal power and rate adaptation and the system-s parameters, as the number of hops per bit, the processing gain applied, the number of users per cell and the received signal-tonoise power ratio over the signal bandwidth. Finally, numerical results are presented to illustrate the proposed mathematical analysis.
Abstract: In this paper, we present an experimental testing for
a new algorithm that determines an optimal controller-s coefficients
for output variance reduction related to Linear Time Invariant (LTI)
Systems. The algorithm features simplicity in calculation, generalization
to minimal and non-minimal phase systems, and could be
configured to achieve reference tracking as well as variance reduction
after compromising with the output variance. An experiment of DCmotor
velocity control demonstrates the application of this new
algorithm in designing the controller. The results show that the
controller achieves minimum variance and reference tracking for a
preset velocity reference relying on an identified model of the motor.
Abstract: A hybrid Photovoltaic/Thermal (PV/T) solar system integrates photovoltaic and solar thermal technologies into one single solar energy device, with dual generation of electricity and heat energy. The aim of the present study is to evaluate the potential for introduction of the PV/T technology into Northern China. For this purpose, outdoor experiments were conducted on a prototype of a PV/T water-heating system. The annual thermal and electrical performances were investigated under the climatic conditions of Beijing. An economic analysis of the system was then carried out, followed by a sensitivity study. The analysis revealed that the hybrid system is not economically attractive with the current market and energy prices. However, considering the continuous commitment of the Chinese government towards policy development in the renewable energy sector, and technological improvements like the increasing cost-effectiveness of PV cells, PV/Thermal technology may become economically viable in the near future.