Abstract: This experimental study consists of a characterization
of epoxy grout where an amount of 2% of graphene nanoplatelets
particles were added to commercial epoxy resin to evaluate their
behavior regarding neat epoxy resin. Compressive tests, tensile tests
and flexural tests were conducted to study the effect of graphene
nanoplatelets on neat epoxy resin. By comparing graphene-based and
neat epoxy grout, there is no significant increase of strength due to
weak interface in the graphene nanoplatelets/epoxy composites.
From this experiment, the tension and flexural strength of graphenebased
epoxy grouts is slightly lower than ones of neat epoxy grout.
Nevertheless, the addition of graphene has produced more consistent
results according to a smaller standard deviation of strength.
Furthermore, the graphene has also improved the ductility of the
grout, hence reducing its brittle behaviour. This shows that the
performance of graphene-based grout is reliably predictable and able
to minimise sudden rupture. This is important since repair design of
damaged pipeline is of deterministic nature.
Abstract: The need to protect our cultural heritage was stressed
on revitalization of historical city centers in communities. The main
aim of this research is to attract finance and activities to the historical
city centers through the citizens and municipalities participation
while cities expanded their boundaries toward suburban areas. Today
the main problems which facing to the most historical city centers, is
loss of their centrality through effect of urbanization on any point of
the cities which is the most important issue on neglect and
abandonment of the historical central area by decentralizing living,
commerce and public areas. This article evaluate the ways in which
city center revitalization can be effect on vitality and viability of the
central area in case of Naghshe Jahan square which situated at the
center of Isfahan city, Iran. Constructed between 1598 and 1629, it is
now an important historical site, and one of UNESCO's World
Heritage Sites.
Abstract: Fluctuations of Schottky diode parameters in a
structure of the mixer are investigated. These fluctuations are
manifested in two ways. At the first, they lead to fluctuations in the
transfer factor that is lead to the amplitude fluctuations in the signal
of intermediate frequency. On the basis of the measurement data of
1/f noise of the diode at forward current, the estimation of a spectrum
of relative fluctuations in transfer factor of the mixer is executed.
Current dependence of the spectrum of relative fluctuations in
transfer factor of the mixer and dependence of the spectrum of
relative fluctuations in transfer factor of the mixer on the amplitude
of the heterodyne signal are investigated. At the second, fluctuations
in parameters of the diode lead to occurrence of 1/f noise in the
output signal of the mixer. This noise limits the sensitivity of the
mixer to the value of received signal.
Abstract: Sewage sludge is a biomass resource that can create a
solid fuel and electricity. Utilizing sewage sludge as a renewable
energy can contribute to the reduction of greenhouse gases. In Japan,
the "National Plan for the Promotion of Biomass Utilization" and the
“Priority Plan for Social Infrastructure Development" were approved
at cabinet meetings in December 2010 and August 2012, respectively,
to promote the energy utilization of sewage sludge. This study
investigated costs and greenhouse gas emission in different sewage
sludge treatments with technologies for energy from sewage sludge.
Expenses were estimated based on capital costs and O&M costs
including energy consumption of solid fuel plants and biogas power
generation plants for sewage sludge. Results showed that the cost of
sludge digestion treatment with solid fuel technologies was 8% lower
than landfill disposal. The greenhouse gas emission of sludge
digestion treatment with solid fuel technologies was also 6,390t as
CO2 smaller than landfill disposal. Biogas power generation reduced
the electricity of a wastewater treatment plant by 30% and the cost by
5%.
Abstract: In the present research, whole meal barley flour
(WBF) was supplemented with gelatinized corn flour (GCF) in 0 and
30%. Whole meal wheat flour (WWF) was mixed with defatted rice
bran (DRB) to produce 0, 20, 25, and 30% replacement levels.
Rheological properties of dough were studied. Thermal properties
and starch crystallinity of flours were evaluated. Flat bread, balady
bread and pie were prepared from the different flour blends. The
different bakeries were sensory evaluated. Color of raw materials and
crust of bakery products were determined. Nutrients contents of raw
flours and food products were assessed. Results showed that addition
of GCF to WBF increased the viscosity and falling number of the
produced dough. Water absorption, dough development time and
dough stability increased with increasing the level of DRB in dough
while, weakening and mixing tolerance index decreased.
Extensibility and energy decreased, while, resistance to extension
increased as DRB level increased. Gelatinized temperature of WWF,
WBF, GCF, and DRB were 13.26, 35.09, 28.33, and 39.63,
respectively. Starch crystallinity was affected when DRB was added
to WWF. The highest protein content was present in balady bread
made from 70% WWF and 30% DRB. The highest calcium,
phosphorus, and potassium levels were present in products made
from 100% WBF. Sensory attributes of the products were slightly
affected by adding DRB and GCF. Conclusion: Addition of DRB or
GCF to WWF or WBF, respectively affect the physical, chemical,
rheological and sensory properties of balady bread, flat bread, and pie
while improved their nutritive values.
Abstract: By using a fixed point theorem of a sum operator, the
existence and uniqueness of positive solution for a class of
boundary value problem of nonlinear fractional differential equation
is studied. An iterative scheme is constructed to approximate it.
Finally, an example is given to illustrate the main result.
Abstract: A Friction stir welding tool is a critical component to
the success of the process. The tool typically consists of a rotating
round shoulder and a threaded cylindrical pin that heats the work
piece, mostly by friction, and moves the softened alloy around it to
form the joint. In this research work, an attempt has been made to
investigate the relationship between FSW variables mainly tool
profile, rotating speed, welding speed and the mechanical properties
(tensile strength, yield strength, percentage elongation, and micro
hardness) of friction stir welded aluminum alloy 5083 joints. From
the experimental details, it can be assessed that the joint produced by
using Triflute profile tool has contribute superior mechanical and
structural properties as compared to Tapered unthreaded & Threaded
tool for 1000rpm.
Abstract: In this paper, a prototype PEM fuel cell vehicle
integrated with a 1 kW air-blowing proton exchange membrane fuel
cell (PEMFC) stack as a main power sources has been developed for
a lightweight cruising vehicle. The test vehicle is equipped with a
PEM fuel cell system that provides electric power to a brushed DC
motor. This vehicle was designed to compete with industrial
lightweight vehicle with the target of consuming least amount of
energy and high performance. Individual variations in driving style
have a significant impact on vehicle energy efficiency and it is well
established from the literature. The primary aim of this study was to
assesses the power and fuel consumption of a hydrogen fuel cell
vehicle operating at three difference driving technique (i.e. 25 km/h
constant speed, 22-28 km/h speed range, 20-30 km/h speed range).
The goal is to develop the best driving strategy to maximize
performance and minimize fuel consumption for the vehicle system.
The relationship between power demand and hydrogen consumption
has also been discussed. All the techniques can be evaluated and
compared on broadly similar terms. Automatic intelligent controller
for driving prototype fuel cell vehicle on different obstacle while
maintaining all systems at maximum efficiency was used. The result
showed that 25 km/h constant speed was identified for optimal
driving with less fuel consumption.
Abstract: Online measurement of the product quality is a
challenging task in cement production, especially in the production of
Celitement, a novel environmentally friendly hydraulic binder. The
mineralogy and chemical composition of clinker in ordinary Portland
cement production is measured by X-ray diffraction (XRD) and
X-ray fluorescence (XRF), where only crystalline constituents can be
detected. But only a small part of the Celitement components can be
measured via XRD, because most constituents have an amorphous
structure. This paper describes the development of algorithms
suitable for an on-line monitoring of the final processing step of
Celitement based on NIR-data. For calibration intermediate products
were dried at different temperatures and ground for variable
durations. The products were analyzed using XRD and
thermogravimetric analyses together with NIR-spectroscopy to
investigate the dependency between the drying and the milling
processes on one and the NIR-signal on the other side. As a result,
different characteristic parameters have been defined. A short
overview of the Celitement process and the challenging tasks of the
online measurement and evaluation of the product quality will be
presented. Subsequently, methods for systematic development of
near-infrared calibration models and the determination of the final
calibration model will be introduced. The application of the model on
experimental data illustrates that NIR-spectroscopy allows for a quick
and sufficiently exact determination of crucial process parameters.
Abstract: This study evaluated to facilitate separation of ABS
plastics from other waste plastics by froth flotation after surface
hydrophilization of ABS with heat treatment. The mild heat treatment
at 100oC for 60s could selectively increase the hydrophilicity of the
ABS plastics surface (i.e., ABS contact angle decreased from 79o to
65.8o) among other plastics mixture. The SEM and XPS results of
plastic samples sufficiently supported the increase in hydrophilic
functional groups and decrease contact angle on ABS surface, after
heat treatment. As a result of the froth flotation (at mixing speed 150
rpm and airflow rate 0.3 L/min) after heat treatment, about 85% of
ABS was selectively separated from other heavy plastics with 100%
of purity. The effect of optimum treatment condition and detailed
mechanism onto separation efficiency in the froth floatation was also
investigated. This research is successful in giving a simple, effective,
and inexpensive method for ABS separation from waste plastics.
Abstract: The strain intensity and redundant strains, dependent
in multistage TRIP wire drawing processes from values used single
partial reductions, should influence on the intensity of transformation
the retained austenite into martensite and thereby on mechanical
properties of drawn wires. The numerical analysis of drawing
processes with use of Drawing 2D programme, for steel wires made
from TRIP steel with 0,29% has been shown in the work. The change
of strain intensity εc and the values of redundant strain εxy, has been
determined for particular draws in dependence of used single partial
reductions.
Abstract: The increase in electric power demand in face of
environmental issues has intensified the participation of renewable
energy sources such as photovoltaics, in the energy matrix of various
countries. Due to their operational characteristics, they can generate
time-varying harmonic and inter-harmonic distortions. For this
reason, the application of methods of measurement based on
traditional Fourier analysis, as proposed by IEC 61000-4-7, can
provide inaccurate results. Considering the aspects mentioned herein,
came the idea of the development of this work which aims to present
the results of a comparative evaluation between a methodology
arising from the combination of the Prony method with the Kalman
filter and another method based on the IEC 61000-4-30 and IEC
61000-4-7 standards. Employed in this study were synthetic signals
and data acquired through measurements in a 50kWp photovoltaic
installation.
Abstract: Value addition to agricultural produce is of possible
potential in reducing poverty, improving food security and
malnutrition, therefore the need to develop small and microenterprises
of sweet potato production. A study was carried out in Nigeria to determine the acceptability
of blends sweet potato (Ipomea batatas) and commodities yellow
maize (Zea mays), millet (Pennisetum glaucum), soybean (Glycine
max), bambara groundnut (Vigna subterranean), guinea corn
(Sorghum vulgare), wheat (Triticum aestivum), and roselle (Hibiscus
sabdariffa) through sensory evaluation. Sweet potato (Ipomea batatas) roots were processed using two
methods: oven and sun drying. The blends were also assessed in
terms of functional, chemical and color properties. Most acceptable blends include BAW (80:20 of sweet
potato/wheat), BBC (80:20 of sweet potato/guinea corn), AAB (60:40
of sweet potato/guinea corn), YTE (100% soybean), TYG (100%
sweet potato), KTN (100% wheat flour), XGP (80:20 of sweet
potato/soybean), XAX (60:40 of sweet potato/wheat), LSS (100%
Roselle), CHK (100% Guinea corn), and ABC (60:40% of sweet
potato/ yellow maize). In addition, carried out chemical analysis
revealed that sweet potato has high percentage of vitamins A and C,
potassium (K), manganese (Mn), calcium (Ca), magnesium (Mg) and
iron (Fe) and fibre content. There is also an increase of vitamin A and
Iron in the blended products.
Abstract: A broadband wire monopole antenna loaded by inhomogeneous stack of annular dielectric ring resonators (DRRs) is proposed. The proposed antenna exhibits a broad impedance bandwidth from 3 to 30 GHz. This is achieved by adding an external step matching network at the antenna feed point. The matching network is comprised of three annular DRRs possessing different permittivity values and sharing the same axial over a finite ground plane. The antenna performance is characterized using full-wave EM simulation. Compared to previous-reported wire antennas with improved bandwidth achieved by DRRs, the proposed topology provides relatively compact realization and superior broadband performance.
Abstract: This paper presents the effect of the orbit inclination
on the pointing error of the satellite antenna and consequently on its
footprint on earth for a typical Ku- band payload system. The performance assessment is examined using both analytical
simulations and practical measurements, taking into account all the
additional sources of the pointing errors, such as East-West station
keeping, orbit eccentricity, and actual attitude control performance. An implementation and computation of the sinusoidal biases in
satellite roll and pitch used to compensate the pointing error of the
satellite antenna coverage is studied and evaluated before and after
the pointing corrections performed. A method for evaluation of the performance of the implemented
biases has been introduced through measuring satellite received level
from a mono-pulse tracking 11.1m transmitting antenna before and
after the implementation of the pointing corrections.
Abstract: The change in orbit evolution between collocated
satellites (X, Y) inside +/-0.09° E/W and +/- 0.07° N/S cluster, after
one of these satellites is placed in an inclined orbit (satellite X) and
the effect of this change in the collocation safety inside the cluster
window has been studied and evaluated. Several collocation scenarios had been studied in order to adjust
the location of both satellites inside their cluster to maximize the
separation between them and safe the mission.
Abstract: Bezier curves have useful properties for path
generation problem, for instance, it can generate the reference
trajectory for vehicles to satisfy the path constraints. Both algorithms
join cubic Bezier curve segment smoothly to generate the path. Some
of the useful properties of Bezier are curvature. In mathematics,
curvature is the amount by which a geometric object deviates from
being flat, or straight in the case of a line. Another extrinsic example
of curvature is a circle, where the curvature is equal to the reciprocal
of its radius at any point on the circle. The smaller the radius, the
higher the curvature thus the vehicle needs to bend sharply. In this
study, we use Bezier curve to fit highway-like curve. We use
different approach to find the best approximation for the curve so that
it will resembles highway-like curve. We compute curvature value by
analytical differentiation of the Bezier Curve. We will then compute
the maximum speed for driving using the curvature information
obtained. Our research works on some assumptions; first, the Bezier
curve estimates the real shape of the curve which can be verified
visually. Even though, fitting process of Bezier curve does not
interpolate exactly on the curve of interest, we believe that the
estimation of speed are acceptable. We verified our result with the
manual calculation of the curvature from the map.
Abstract: In the present study, feasibility of the selective surface
hydrophilization of polyvinyl chloride (PVC) by microwave treatment
was evaluated to facilitate the separation from automotive shredder
residue (ASR), by the froth flotation. The combination of 60 sec
microwave treatment with PAC, a sharp and significant decrease about
16.5° contact angle of PVC was observed in ASR plastic compared
with other plastics. The microwave treatment with the addition of PAC
resulted in a synergetic effect for the froth flotation, which may be a
result of the 90% selective separation of PVC from ASR plastics, with
82% purity. While, simple mixing with a nanometallic Ca/CaO/PO4
dispersion mixture immobilized 95-100% of heavy metals in ASR
soil/residues. The quantity of heavy metals leached from thermal
residues after treatment by nanometallic Ca/CaO/PO4 was lower than
the Korean standard regulatory limit for hazardous waste landfills.
Microwave treatment can be a simple and effective method for PVC
separation from ASR plastics.
Abstract: Customer’ needs, quality, and value creation while
reducing costs through supply chain management provides challenges
and opportunities for companies and researchers. In the light of these
challenges, modern ideas must contribute to counter these challenges
and exploit opportunities. Therefore, this paper discusses the impact
of the quality cost on revenue sharing as a most important incentive
to configure business networks. This paper develops the quality cost approach to align with the
modern era. It develops a model to measure quality costs which
might enable firms to manage revenue sharing in a supply chain. The
developed model includes five categories; besides the well-known
four categories (namely prevention costs, appraisal costs, internal
failure costs, and external failure costs), a new category has been
developed in this research as a new vision of the relationship between
quality costs and innovations in industry. This new category is
Recycle Cost. This paper also examines whether such quality costs in
supply chains influence the revenue sharing between partners. Using the author's quality cost model, the relationship between
quality costs and revenue sharing among partners is examined using a
case study in an Egyptian manufacturing company which is a part of
a supply chain. This paper argues that the revenue-sharing proportion
allocated to supplier increases as the recycle cost of supplier
increases, and the revenue-sharing proportion allocated to
manufacturer increases as the prevention and appraisal costs increase,
as well as the failure costs, the recycle costs of manufacturer, and the
recycle costs of suppliers decrease. However, the results present
surprising findings. The purposes of this study are developing quality cost approach
and understanding the relationships between quality costs and
revenue sharing in supply chains. Therefore, the present study
contributes to theory and practice by explaining how the cost of
recycling can be combined in quality cost model to better
understanding the revenue sharing among partners in supply chains.
Abstract: Prior literature in the field of adaptive and
personalized learning sequence in e-learning have proposed and
implemented various mechanisms to improve the learning process
such as individualization and personalization, but complex to
implement due to expensive algorithmic programming and need of
extensive and prior data. The main objective of personalizing
learning sequence is to maximize learning by dynamically selecting
the closest teaching operation in order to achieve the learning
competency of learner. In this paper, a revolutionary technique has
been proposed and tested to perform individualization and
personalization using modified reversed roulette wheel selection
algorithm that runs at O(n). The technique is simpler to implement
and is algorithmically less expensive compared to other revolutionary
algorithms since it collects the dynamic real time performance matrix
such as examinations, reviews, and study to form the RWSA single
numerical fitness value. Results show that the implemented system is
capable of recommending new learning sequences that lessens time
of study based on student's prior knowledge and real performance
matrix.