Abstract: A designing of a structure requires its realization on rough or sloping ground. Besides the problem of the stability of the landslide, the behavior of the foundations that are bearing the structure is influenced by the destabilizing effect of the ground’s slope. This article focuses on the analysis of the slope stability exposed to loading by introducing the different factors influencing the slope’s behavior on the one hand, and on the influence of this slope on the foundation’s behavior on the other hand. This study is about the elastoplastic modelization using FLAC 2D. This software is based on the finite difference method, which is one of the older methods of numeric resolution of differential equations system with initial and boundary conditions. It was developed for the geotechnical simulation calculation. The aim of this simulation is to demonstrate the notable effect of shear modulus « G », cohesion « C », inclination angle (edge) « β », and distance between the foundation and the head of the slope on the stability of the slope as well as the stability of the foundation. In our simulation, the slope is constituted by homogenous ground. The foundation is considered as rigid/hard; therefore, the loading is made by the application of the vertical strengths on the nodes which represent the contact between the foundation and the ground.
Abstract: This study focuses on the effect of pin taper tool ratio on friction stir welding of magnesium alloy AZ31. Two pieces of AZ31 alloy with thickness of 6 mm were friction stir welded by using the conventional milling machine. The shoulder diameter used in this experiment is fixed at 18 mm. The taper pin ratio used are varied at 6:6, 6:5, 6:4, 6:3, 6:2 and 6:1. The rotational speeds that were used in this study were 500 rpm, 1000 rpm and 1500 rpm, respectively. The welding speeds used are 150 mm/min, 200 mm/min and 250 mm/min. Microstructure observation of welded area was studied by using optical microscope. Equiaxed grains were observed at the TMAZ and stir zone indicating fully plastic deformation. Tool pin diameter ratio 6/1 causes low heat input to the material because of small contact surface between tool surface and stirred materials compared to other tool pin diameter ratio. The grain size of stir zone increased with increasing of ratio of rotational speed to transverse speed due to higher heat input. It is observed that worm hole is produced when excessive heat input is applied. To evaluate the mechanical properties of this specimen, tensile test was used in this study. Welded specimens using taper pin ratio 6:1 shows higher tensile strength compared to other taper pin ratio up to 204 MPa. Moreover, specimens using taper pin ratio 6:1 showed better tensile strength with 500 rpm of rotational speed and 150mm/min welding speed.
Abstract: Headache is one of the most ubiquitous and frequent
neurological disorders interfering with everyday life in all countries.
India appears to be no exception. Objectives are to assess the
prevalence of headache among adult population in urban area of
Varanasi and to find out factors influencing the occurrence of
headache. A community based cross sectional study was conducted
among adult population in urban area of Varanasi district, Uttar
Pradesh, India. Total 151 eligible respondents were interviewed by
simple random sampling technique. Proportion percentage and Chisquare
test were applied for data analysis. Out of 151 respondents,
majority (58.3%) were females. In this study, 92.8% respondents
belonged to age group 18-60 years while 7.2% was either 60 year of
age or above. The overall prevalence of headache was found to be
51.1%. Highest and lowest prevalence of headache was recorded in
age groups 18-29 year & 40-49 year respectively. Headache was
62.1% in illiterate and was 40.0% among graduate & above.
Unskilled workers had more headache 73.1% than other type of
occupation. Headache was more prevalent among unemployed
(35.9%) than employed (6.4%). Females had higher family history of
headache (48.9%) as compared to males (41.3%). Study subjects
having peaceful relation with family members, relatives and
neighbors had more headache than those having no peaceful relation.
Abstract: This research provides a systematic way to study and
better understand double nano-tubular structure of alunina (Al2O3) and
titania (TiO2). The TiO2 NT was prepared by immersing Al2O3
template in 0.02 M titanium fluoride (TiF4) solution (pH=3) at 25 °C
for 120 min, followed by annealing at 450 °C for 1 h to obtain anatase
TiO2 NT in the Al2O3 template. Large-scale development of film for
nanotube-based CO2 capture and conversion can potentially result in
more efficient energy harvesting. In addition, the production process
will be relatively environmentally friendly. The knowledge generated
by this research will significantly advance research in the area of
Al2O3, TiO2, CaO, and Ca2O3 nano-structure film fabrication and
applications for CO2 capture and conversion. This green energy source
will potentially reduce reliance on carbon-based energy resources and
increase interest in science and engineering careers.
Abstract: This paper presents the trajectory tracking control of a
spatial redundant hybrid manipulator. This manipulator consists of
two parallel manipulators which are a variable geometry truss (VGT)
module. In fact, each VGT module with 3-degress of freedom (DOF)
is a planar parallel manipulator and their operational planes of these
VGT modules are arranged to be orthogonal to each other. Also, the
manipulator contains a twist motion part attached to the top of the
second VGT module to supply the missing orientation of the endeffector.
These three modules constitute totally 7-DOF hybrid
(parallel-parallel) redundant spatial manipulator. The forward
kinematics equations of this manipulator are obtained, then,
according to these equations, the inverse kinematics is solved based
on an optimization with the joint limit avoidance. The dynamic
equations are formed by using virtual work method. In order to test
the performance of the redundant manipulator and the controllers
presented, two different desired trajectories are followed by using the
computed force control method and a switching control method. The
switching control method is combined with the computed force
control method and genetic algorithm. In the switching control
method, the genetic algorithm is only used for fine tuning in the
compensation of the trajectory tracking errors.
Abstract: In this study, natural bentonite was used as natural
clay material and samples were taken from the Kalecik district in
Ankara. In this research, bentonite is the subject of an analysis from
standpoint of assessing the basic properties of engineered barriers
with respect to the buffer material. Bentonite and sand mixtures were
prepared for tests. Some of clay minerals give relatively higher
hydraulic conductivity and lower swelling pressure. Generally,
hydraulic conductivity of these type clays is lower than
Abstract: The technological paradigm of the disaster
management field, especially in the case of governmental
intervention strategies, is generally based on rapid and flexible
accommodation solutions. From various technical solution patterns
used to address the immediate housing needs of disaster victims, the
adaptive re-use of existing buildings can be considered to be both
low-cost and practical. However, there is a scarcity of analytical
methods to screen, select and adapt buildings to help decision makers
in cases of emergency. Following an extensive literature review, this
paper aims to highlight key points and problem areas associated with
the adaptive re-use of buildings within the disaster management
context. In other disciplines such as real estate management, the
adaptive re-use potential (ARP) of existing buildings is typically
based on the prioritization of a set of technical and non-technical
criteria which are then weighted to arrive at an economically viable
investment decision. After a disaster, however, the assessment of the
ARP of buildings requires consideration of different/additional layers
of analysis which stem from general disaster management principles
and the peculiarities of different types of disasters, as well as of their
victims. In this paper, a discussion of the development of an adaptive
re-use potential (ARP) assessment model is presented. It is thought
that governmental and non-governmental decision makers who are
required to take quick decisions to accommodate displaced masses
following disasters are likely to benefit from the implementation of
such a model.
Abstract: Imazu Bay plays an important role for endangered
species such as horseshoe crabs and black-faced spoonbills that stay in
the bay for spawning or the passing of winter. However, this bay is
semi-enclosed with slow water exchange, which could lead to
eutrophication under the condition of excess nutrient inflow to the bay.
Therefore, quantification of nutrient inflow is of great importance.
Generally, analysis of nutrient inflow to the bays takes into
consideration nutrient inflow from only the river, but that from
groundwater should not be ignored for more accurate results. The main
objective of this study is to estimate the amounts of nutrient inflow
from river and groundwater to Imazu Bay by analyzing water budget
in Zuibaiji River Basin and loads of T-N, T-P, NO3-N and NH4-N. The
water budget computation in the basin is performed using groundwater
recharge model and quasi three-dimensional two-phase groundwater
flow model, and the multiplication of the measured amount of nutrient
inflow with the computed discharge gives the total amount of nutrient
inflow to the bay. In addition, in order to evaluate nutrient inflow to the
bay, the result is compared with nutrient inflow from geologically
similar river basins. The result shows that the discharge is 3.50×107
m3/year from the river and 1.04×107 m3/year from groundwater. The
submarine groundwater discharge accounts for approximately 23 % of
the total discharge, which is large compared to the other river basins. It
is also revealed that the total nutrient inflow is not particularly large.
The sum of NO3-N and NH4-N loadings from groundwater is less than
10 % of that from the river because of denitrification in groundwater.
The Shin Seibu Sewage Treatment Plant located below the observation
points discharges treated water of 15,400 m3/day and plans to increase
it. However, the loads of T-N and T-P from the treatment plant are 3.9
mg/L and 0.19 mg/L, so that it does not contribute a lot to
eutrophication.
Abstract: Waste polyethylene (PE) is classified as waste low
density polyethylene (LDPE) and waste high density polyethylene
(HDPE) according to their densities. Pyrolysis of plastic waste may
have an important role in dealing with the enormous amounts of
plastic waste produced all over the world, by decreasing their
negative impact on the environment. This waste may be converted
into economically valuable hydrocarbons, which can be used both as
fuels and as feed stock in the petrochemical industry. End product
yields and properties depend on the plastic waste composition.
Pyrolytic biochar is one of the most important products of waste
plastics pyrolysis. In this study, HDPE and LDPE plastic wastes were
co-pyrolyzed together with waste olive pomace. Pyrolysis runs were
performed at temperature 700°C with heating rates of 5°C/min.
Higher pyrolysis oil and gas yields were observed by the using waste
olive pomace. The biochar yields of HDPE- olive pomace and LDPEolive
pomace were 6.37% and 7.26% respectively for 50% olive
pomace doses. The calorific value of HDPE-olive pomace and
LDPE-olive pomace of pyrolysis oil were 8350 and 8495 kCal.
Abstract: The development of numerical analysis and its
application to geomechanics problems have provided geotechnical
engineers with extremely powerful tools. One of the most important
problems in geotechnical engineering is the slope stability
assessment. It is a very difficult task due to several aspects such the
nature of the problem, experimental consideration, monitoring,
controlling, and assessment. The main objective of this paper is to
perform a comparative numerical study between the following
methods: The Limit Equilibrium (LEM), Finite Element (FEM),
Limit Analysis (LAM) and Distinct Element (DEM). The comparison
is conducted in terms of the safety factors and the critical slip
surfaces. Through the results, we see the feasibility to analyse slope
stability by many methods.
Abstract: The aim of this work is to present a low cost adsorbent
for removing toxic heavy metals from aqueous solutions. Therefore,
we are interested to investigate the efficiency of natural clay minerals
collected from south Tunisia and their modified form using sulfuric
acid in the removal of toxic metal ions: Zn(II) and Pb(II) from
synthetic waste water solutions. The obtained results indicate that
metal uptake is pH-dependent and maximum removal was detected to
occur at pH 6. Adsorption equilibrium is very rapid and it was
achieved after 90 min for both metal ions studied. The kinetics results
show that the pseudo-second-order model describes the adsorption
and the intraparticle diffusion models are the limiting step. The
treatment of natural clay with sulfuric acid creates more active sites
and increases the surface area, so it showed an increase of the
adsorbed quantities of lead and zinc in single and binary systems. The
competitive adsorption study showed that the uptake of lead was
inhibited in the presence of 10 mg/L of zinc. An antagonistic binary
adsorption mechanism was observed. These results revealed that clay
is an effective natural material for removing lead and zinc in single
and binary systems from aqueous solution.
Abstract: The idea of cropping-system is a method used by
farmers. It is an environmentally-friendly method, protecting the
natural resources (soil, water, air, nutritive substances) and increase
the production at the same time, taking into account some crop
particularities. The combination of this powerful method with the
concepts of genetic algorithms results into a possibility of generating
sequences of crops in order to form a rotation. The usage of this type
of algorithms has been efficient in solving problems related to
optimization and their polynomial complexity allows them to be used
at solving more difficult and various problems. In our case, the
optimization consists in finding the most profitable rotation of
cultures. One of the expected results is to optimize the usage of the
resources, in order to minimize the costs and maximize the profit. In
order to achieve these goals, a genetic algorithm was designed. This
algorithm ensures the finding of several optimized solutions of
cropping-systems possibilities which have the highest profit and,
thus, which minimize the costs. The algorithm uses genetic-based
methods (mutation, crossover) and structures (genes, chromosomes).
A cropping-system possibility will be considered a chromosome and
a crop within the rotation is a gene within a chromosome. Results
about the efficiency of this method will be presented in a special
section. The implementation of this method would bring benefits into
the activity of the farmers by giving them hints and helping them to
use the resources efficiently.
Abstract: The aim of the paper is to investigate the effect of
corporate social responsibility (CSR) CSR on the National
Commercial Bank (NCB) in Saudi Arabia. In order to achieve this, a
case study was made of the CSR activities of this bank from the
perspective of its branch managers. The NCB was chosen as it was
one of the first Saudi banks to engage in CSR and currently has a
wide range of CSR initiatives. A qualitative research method was
used. Open-ended questionnaires were administered to eighty branch
managers of the NCB, with fifty-five usable questionnaires returned
and twenty managers were interviewed as part of the primary
research. Data from both questionnaires and interviews were
analysed using qualitative content analysis. Six themes emerged from
the questionnaire findings were used to develop the interview
questions. These themes are the following: Awareness of employees
about CSR in the NCB; CSR activities as a type of investment;
Government and media support; Increased employee loyalty in the
NCB; Prestige and profit to the NCB; and View of CSR in Islam.
This paper makes a theoretical contribution in that it investigates and
increases understanding of the effect of CSR on the NCB in Saudi
Arabia. In addition, it makes a practical contribution by making
recommendations which can support the development of CSR in the
NCB. A limitation of the paper is that it is a case study of only one
bank. It is therefore recommended that future research could be
conducted with other banks in Saudi Arabia, or indeed, with a range
of other types of firm within the financial services area in Saudi
Arabia. In this way, the same issues could be explored but with a
greater potential generalisability of findings of CSR within the Saudi
Arabian financial services industry. In addition, this paper takes a
qualitative approach and it is suggested that future research be carried
out using mixed methods, which could provide a greater depth of
analysis.
Abstract: In an economic crisis such as the one that shook (and still shake) Europe, one does not question the importance of the measures that encourage the hiring and integration of young people into the labour market. In the mentioned context, enterprises tend to reduce the cost of labour and to seek flexible contracting instruments. The professional internships allow innovation and creativity at low cost, because, as they are not labour contracts, the enterprises do not have to respect the minimum standards related to wages, working time duration and so on. In Portugal, we observe a widespread existence of training contracts in which the trainee worked several hours without salary or was paid below the legally prescribed for the function and the work period. For this reason, under the tripartite agreement for a new system of regulation of labour relations, employment policies and social protection, between the Government and the social partners, in June 2008, foresaw a prohibition of professional internships unpaid and the legal regulation of the mandatory internships for access to an activity. The first Act about private internship contracts, i.e., internships without public funding was embodied in the Decree-Law N. 66/2011, of 1st June. This work is dedicated to the study of the legal regime of the internship contract in Portugal, by analysing the problems brought by the new set of rules and especially those which remains unresolved. In fact, we can conclude that the number of situations covered by the Act is much lower than what was expected, because of the exclusion of the mandatory internship for access to a profession when the activity is developed autonomously. Since the majority of the activities can be developed both autonomously or subordinated, it is quite easy to out of the Act requirements and, so, out of the protection that it confers to the intern. In order to complete this study, we considered not only the mentioned legal Act, but also the few doctrine and jurisprudence about the theme.
Abstract: Solid particle erosion has been identified as a critical wear phenomenon which takes place during operation of aeroengines in dusty environment. The present work discusses the erosion behavior of Ti-44.5Al-6.25Nb-0.8Mo-0.1B alloy (TNB-V4) which finds its application in low pressure gas turbines and can be used for high pressure compressors too. Prior to the erosion tests, the alloy was heat treated to improve the mechanical properties. Afterwards, specimens were eroded at impact angles of 30° and 90° at room and high temperatures (100 °C-400 °C). Volume loss and erosion behavior are studied through gravimetric analysis, whereas erosion mechanisms are characterized through scanning electron microscopy. The results indicate a clear difference in the erosion mechanism for different impact angles. The influence of the test temperature on the erosion behavior of the alloy is also discussed in the present contribution.
Abstract: An approach to compute optimum seismic design parameters is presented. It is based on the optimization of the expected present value of the total cost, which includes the initial cost of structures as well as the cost due to earthquakes. Different types of seismicity models are considered, including one for characteristic earthquakes. Uncertainties are included in some variables to observe the influence on optimum values. Optimum seismic design coefficients are computed for three different structural types representing high, medium and low rise buildings, located near and far from the seismic sources. Ordinary and important structures are considered in the analysis. The results of optimum values show an important influence of seismicity models as well as of uncertainties on the variables.
Abstract: Particle reinforced Metal Matrix Composite (MMC) succeeds in synergizing the metallic matrix with ceramic particle reinforcements to result in improved strength, particularly at elevated temperatures, but adversely it affects the ductility of the matrix because of agglomeration and porosity. The present study investigates the outcome of tensile properties in a cast and hot forged composite reinforced simultaneously with coarse and fine particles. Nano-sized alumina particles have been generated by milling mixture of aluminum and manganese dioxide powders. Milled particles after drying are added to molten metal and the resulting slurry is cast. The microstructure of the composites shows good distribution of both the size categories of particles without significant clustering. The presence of nanoparticles along with coarser particles in a composite improves both strength and ductility considerably. Delay in debonding of coarser particles to higher stress is due to reduced mismatch in extension caused by increased strain hardening in presence of the nanoparticles. However, higher addition of powder mix beyond a limit results in deterioration of mechanical properties, possibly due to clustering of nanoparticles. The porosity in cast composite generally increases with the increasing addition of powder mix as observed during process and on forging it has got reduced. The base alloy and nanocomposites show improvement in flow stress which could be attributed to lowering of porosity and grain refinement as a consequence of forging.
Abstract: In connected vehicle systems where wireless communication is available among the involved vehicles and intersection controllers, it is possible to design an intersection coordination strategy that leads the connected and automated vehicles (CAVs) travel through the road intersections without the conventional traffic light control. In this paper, we present a distributed coordination strategy for the CAVs at multiple interconnected intersections that aims at improving system fuel efficiency and system mobility. We present a distributed control solution where in the higher level, the intersection controllers calculate the road desired average velocity and optimally assign reference velocities of each vehicle. In the lower level, every vehicle is considered to use model predictive control (MPC) to track their reference velocity obtained from the higher level controller. The proposed method has been implemented on a simulation-based case with two-interconnected intersection network. Additionally, the effects of mixed vehicle types on the coordination strategy has been explored. Simulation results indicate the improvement on vehicle fuel efficiency and traffic mobility of the proposed method.
Abstract: Lightweight construction became more and more important over the last decades in several applications, e.g. in the automotive or aircraft sector. This is the result of economic and ecological constraints on the one hand and increasing safety and comfort requirements on the other hand. In the field of lightweight design, different approaches are used due to specific requirements towards the technical systems. The use of endless carbon fiber reinforced plastics (CFRP) offers the largest weight saving potential of sometimes more than 50% compared to conventional metal-constructions. However, there are very limited industrial applications because of the cost-intensive manufacturing of the fibers and production technologies. Other disadvantages of pure CFRP-structures affect the quality control or the damage resistance. One approach to meet these challenges is hybrid materials. This means CFRP and sheet metal are combined on a material level. Therefore, new opportunities for innovative process routes are realizable. Hybrid lightweight design results in lower costs due to an optimized material utilization and the possibility to integrate the structures in already existing production processes of automobile manufacturers. In recent and current research, the advantages of two-layered hybrid materials have been pointed out, i.e. the possibility to realize structures with tailored mechanical properties or to divide the curing cycle of the epoxy resin into two steps. Current research work at the Chair for Automotive Lightweight Design (LiA) at the Paderborn University focusses on production processes for fiber-metal-laminates. The aim of this work is the development and qualification of a large-scale production process for high-performance fiber-metal-laminates (FML) for industrial applications in the automotive or aircraft sector. Therefore, the prepreg-press-technology is used, in which pre-impregnated carbon fibers and sheet metals are formed and cured in a closed, heated mold. The investigations focus e.g. on the realization of short process chains and cycle times, on the reduction of time-consuming manual process steps, and the reduction of material costs. This paper gives an overview over the considerable steps of the production process in the beginning. Afterwards experimental results are discussed. This part concentrates on the influence of different process parameters on the mechanical properties, the laminate quality and the identification of process limits. Concluding the advantages of this technology compared to conventional FML-production-processes and other lightweight design approaches are carried out.
Abstract: Wireless Sensor Network (WSN) clustering architecture enables features like network scalability, communication overhead reduction, and fault tolerance. After clustering, aggregated data is transferred to data sink and reducing unnecessary, redundant data transfer. It reduces nodes transmitting, and so saves energy consumption. Also, it allows scalability for many nodes, reduces communication overhead, and allows efficient use of WSN resources. Clustering based routing methods manage network energy consumption efficiently. Building spanning trees for data collection rooted at a sink node is a fundamental data aggregation method in sensor networks. The problem of determining Cluster Head (CH) optimal number is an NP-Hard problem. In this paper, we combine cluster based routing features for cluster formation and CH selection and use Minimum Spanning Tree (MST) for intra-cluster communication. The proposed method is based on optimizing MST using Simulated Annealing (SA). In this work, normalized values of mobility, delay, and remaining energy are considered for finding optimal MST. Simulation results demonstrate the effectiveness of the proposed method in improving the packet delivery ratio and reducing the end to end delay.