Abstract: The fundamental aim of extended expansion concept is
to achieve higher work done which in turn leads to higher thermal
efficiency. This concept is compatible with the application of
turbocharger and LHR engine. The Low Heat Rejection engine was
developed by coating the piston crown, cylinder head inside with
valves and cylinder liner with partially stabilized zirconia coating of
0.5 mm thickness. Extended expansion in diesel engines is termed as
Miller cycle in which the expansion ratio is increased by reducing the
compression ratio by modifying the inlet cam for late inlet valve
closing. The specific fuel consumption reduces to an appreciable level
and the thermal efficiency of the extended expansion turbocharged
LHR engine is improved.
In this work, a thermodynamic model was formulated and
developed to simulate the LHR based extended expansion
turbocharged direct injection diesel engine. It includes a gas flow
model, a heat transfer model, and a two zone combustion model. Gas
exchange model is modified by incorporating the Miller cycle, by
delaying inlet valve closing timing which had resulted in considerable
improvement in thermal efficiency of turbocharged LHR engines. The
heat transfer model, calculates the convective and radiative heat
transfer between the gas and wall by taking into account of the
combustion chamber surface temperature swings. Using the two-zone
combustion model, the combustion parameters and the chemical
equilibrium compositions were determined. The chemical equilibrium
compositions were used to calculate the Nitric oxide formation rate by
assuming a modified Zeldovich mechanism. The accuracy of this
model is scrutinized against actual test results from the engine. The
factors which affect thermal efficiency and exhaust emissions were
deduced and their influences were discussed. In the final analysis it is
seen that there is an excellent agreement in all of these evaluations.
Abstract: High voltage generators are being subject to higher
voltage rating and are being designed to operate in harsh conditions.
Stator windings are the main component of generators in which
Electrical, magnetical and thermal stresses remain major failures for
insulation degradation accelerated aging. A large number of
generators failed due to stator winding problems, mainly insulation
deterioration. Insulation degradation assessment plays vital role in the
asset life management. Mostly the stator failure is catastrophic
causing significant damage to the plant. Other than generation loss,
stator failure involves heavy repair or replacement cost. Electro
thermal analysis is the main characteristic for improvement design of
stator slot-s insulation. Dielectric parameters such as insulation
thickness, spacing, material types, geometry of winding and slot are
major design consideration. A very powerful method available to
analyze electro thermal performance is Finite Element Method
(FEM) which is used in this paper. The analysis of various stator coil
and slot configurations are used to design the better dielectric system
to reduce electrical and thermal stresses in order to increase the
power of generator in the same volume of core. This paper describes
the process used to perform classical design and improvement
analysis of stator slot-s insulation.
Abstract: Numerical studies have been carried out using a two
dimensional code to examine the influence of pressure / thrust
transient of solid propellant rockets at liftoff. This code solves
unsteady Reynolds-averaged thin-layer Navier–Stokes equations by
an implicit LU-factorization time-integration method. The results
from the parametric study indicate that when the port is narrow there
is a possibility of increase in pressure / thrust-rise rate due to
relatively high flame spread rate. Parametric studies further reveal
that flame spread rate can be altered by altering the propellant
properties, igniter jet characteristics and nozzle closure burst pressure
without altering the grain configuration and/or the mission
demanding thrust transient. We observed that when the igniter
turbulent intensity is relatively low the vehicle could liftoff early due
to the early flow choking of the rocket nozzle. We concluded that the
high pressurization-rate has structural implications at liftoff in
addition to transient burning effect. Therefore prudent selection of the
port geometry and the igniter, for meeting the mission requirements,
within the given envelop are meaningful objectives for any designer
for the smooth liftoff of solid propellant rockets.
Abstract: Now a days, a significant part of commercial and governmental organisations like museums, cultural organizations, libraries, commercial enterprises, etc. invest intensively in new technologies for image digitization, digital libraries, image archiving and retrieval. Hence image authorization, authentication and security has become prime need. In this paper, we present a semi-fragile watermarking scheme for color images. The method converts the host image into YIQ color space followed by application of orthogonal dual domains of DCT and DWT transforms. The DCT helps to separate relevant from irrelevant image content to generate silent image features. DWT has excellent spatial localisation to help aid in spatial tamper characterisation. Thus image adaptive watermark is generated based of image features which allows the sharp detection of microscopic changes to locate modifications in the image. Further, the scheme utilises the multipurpose watermark consisting of soft authenticator watermark and chrominance watermark. Which has been proved fragile to some predefined processing like intentinal fabrication of the image or forgery and robust to other incidental attacks caused in the communication channel.
Abstract: Noble metal participation in nanostructured
semiconductor catalysts has drawn much interest because of their
improved properties. Recently, it has been discussed by many
researchers that Ag participation in TiO2, CuO, ZnO semiconductors
showed improved photocatalytic and optical properties. In this
research, Ag/ZnO nanocomposite particles were prepared by
Ultrasonic Spray Pyrolysis(USP) Method. 0.1M silver and zinc
nitrate aqueous solutions were used as precursor solutions. The
Ag:Zn atomic ratio of the solution was selected 1:1. Experiments
were taken place under constant air flow of 400 mL/min at 800°C
furnace temperature. Particles were characterized by X-Ray
Diffraction (XRD), Scanning Electron Microscope (SEM) and
Energy Dispersive Spectroscopy (EDS). The crystallite sizes of Ag
and ZnO in composite particles are 24.6 nm, 19.7 nm respectively.
Although, spherical nanocomposite particles are in a range of 300-
800 nm, these particles are formed by the aggregation of primary
particles which are in a range of 20-60 nm.
Abstract: Bangla Vowel characterization determines the spectral properties of Bangla vowels for efficient synthesis as well as recognition of Bangla vowels. In this paper, Bangla vowels in isolated word have been analyzed based on speech production model within the framework of Analysis-by-Synthesis. This has led to the extraction of spectral parameters for the production model in order to produce different Bangla vowel sounds. The real and synthetic spectra are compared and a weighted square error has been computed along with the error in the formant bandwidths for efficient representation of Bangla vowels. The extracted features produced good representation of targeted Bangla vowel. Such a representation also plays essential role in low bit rate speech coding and vocoders.
Abstract: This study investigated the effect of germination on chemical compositions, physio-chemical properties of malted (germinated) red sorghum flours and evaluated characteristics of gluten free breads from sorghum flour. Results showed that germinated sorghum flour had higher amylase activity, swelling power and solubility at 95°C, but lower in the peak, break down, final and set back viscosities than ungerminated sample (p≤0.05). Five gluten free breads made from sorghum flour blends, with different ratios of ungerminated and germinated sorghum flour, were compared for the physical properties with those made from wheat flour. Crumb hardness, cohesiveness, gumminess and chewiness of sorghum breads were found significantly higher than those of wheat bread. With increasing of ungerminated flour proportion, the bread hardness increased while the cohesiveness declined. Sorghum breads appeared red to human eyes with a*values of 10.41-15.77.Their crust and crumb colors differed significantly from those of wheat bread.
Abstract: In this paper, a multi-branch power line is modeled using ABCD matrix to show its worth as a communication channel. The model is simulated using MATLAB in an effort to investigate the effects of multiple loading, multipath, and those as a result of load mismatching. The channel transfer function is obtained and investigated using different cable lengths, and different number of bridge taps under given loading conditions.
Abstract: Let S be an ordered semigroup. In this paper we first introduce the concepts of (∈,∈ ∨q)-fuzzy ideals, (∈,∈ ∨q)-fuzzy bi-ideals and (∈,∈ ∨q)-fuzzy generalized bi-ideals of an ordered semigroup S, and investigate their related properties. Furthermore, we also define the upper and lower parts of fuzzy subsets of an ordered semigroup S, and investigate the properties of (∈,∈ ∨q)-fuzzy ideals of S. Finally, characterizations of regular ordered semigroups and intra-regular ordered semigroups by means of the lower part of (∈ ,∈ ∨q)-fuzzy left ideals, (∈,∈ ∨q)-fuzzy right ideals and (∈,∈ ∨q)- fuzzy (generalized) bi-ideals are given.
Abstract: In this study, we sought to investigate the mercury
removal efficiency of manganese oxides from natural gas. The
fundamental studies on mercury removal with manganese oxides
sorbents were carried out in a laboratory scale fixed bed reactor at 30
°C with a mixture of methane (20%) and nitrogen gas laden with 4.8
ppb of elemental mercury. Manganese oxides with varying surface
area and crystalline phase were prepared by conventional precipitation
method in this study. The effects of surface area, crystallinity and
other metal oxides on mercury removal efficiency were investigated.
Effect of Ag impregnation on mercury removal efficiency was also
investigated. Ag supported on metal oxide such titania and zirconia as
reference materials were also used in this study for comparison. The
characteristics of mercury removal reaction with manganese oxide
was investigated using a temperature programmed desorption (TPD)
technique.
Manganese oxides showed very high Hg removal activity (about
73-93% Hg removal) for first time use. Surface area of the manganese
oxide samples decreased after heat-treatment and resulted in complete
loss of Hg removal ability for repeated use after Hg desorption in the
case of amorphous MnO2, and 75% loss of the initial Hg removal
activity for the crystalline MnO2. Mercury desorption efficiency of
crystalline MnO2 was very low (37%) for first time use and high (98%)
after second time use. Residual potassium content in MnO2 may have
some effect on the thermal stability of the adsorbed Hg species.
Desorption of Hg from manganese oxides occurs at much higher
temperatures (with a peak at 400 °C) than Ag/TiO2 or Ag/ZrO2.
Mercury may be captured on manganese oxides in the form of mercury
manganese oxide.
Abstract: A mathematical model based on a mass and energy
balance for the combustion in a cement rotary kiln was developed.
The model was used to investigate the impact of replacing about
45 % of the primary coal energy by different alternative fuels.
Refuse derived fuel, waste wood, solid hazardous waste and liquid
hazardous waste were used in the modeling. The results showed that
in order to keep the kiln temperature unchanged, and thereby
maintain the required clinker quality, the production capacity had to
be reduced by 1-15 %, depending on the fuel type. The reason for the
reduction is increased exhaust gas flow rates caused by the fuel
characteristics. The model, which has been successfully validated in a
full-scale experiment, was also used to show that the negative impact
on the production capacity can be avoided if a relatively small part of
the combustion air is replaced by pure oxygen.
Abstract: Electro Discharge Sawing is a hybrid process
combining the features of SEDM and ECM. Its major characteristic is
extremely fast erosion rate compare to either of the above processes.
This paper brings out its relative feature of SEDM and EDS about
their erosion rates, surface roughness, and morphology of machined
surfaces.
Abstract: Earthquakes are natural phenomena that occur with influence of a lot of parameters such as seismic activity, changing in the ground waters' motion, changing in the water-s temperature, etc. On the other hand, the radon gas concentrations in soil vary as nonlinear generally with earthquakes. Continuous measurement of the soil radon gas is very important for determination of characteristic of the seismic activity. The radon gas changes as continuous with strain occurring within the Earth-s surface during an earthquake and effects from the physical and the chemical processes such as soil structure, soil permeability, soil temperature, the barometric pressure, etc. Therefore, at the modeling researches are notsufficient to knowthe concentration ofradon gas. In this research, we determined relationships between radon emissions based on the environmental parameters and earthquakes occurring along the East Anatolian Fault Zone (EAFZ), Turkiye and predicted magnitudes of some earthquakes with the artificial neural network (ANN) model.
Abstract: Thermoplastic starch, polylactic acid glycerol and
maleic anhydride (MA) were compounded with natural
montmorillonite (MMT) through a twin screw extruder to investigate
the effects of different loading of MMT on structure, thermal and
absorption behavior of the nanocomposites. X-ray diffraction analysis
(XRD) showed that sample with MMT loading 4phr exhibited
exfoliated structure while sample that contained MMT 8 phr
exhibited intercalated structure. FESEM images showed big lump
when MMT loading was at 8 phr. The thermal properties were
characterized by using differential scanning calorimeter (DSC). The
results showed that MMT increased melting temperature and
crystallization temperature of matrix but reduction in glass transition
temperature was observed Meanwhile the addition of MMT has
improved the water barrier property. The nanosize MMT particle is
also able to block a tortuous pathway for water to enter the starch
chain, thus reducing the water uptake and improved the physical
barrier of nanocomposite.
Abstract: This paper presents a silicon controller rectifier (SCR)
based ESD protection circuit for IC. The proposed ESD protection
circuit has low trigger voltage and high holding voltage compared with
conventional SCR ESD protection circuit. Electrical characteristics of
the proposed ESD protection circuit are simulated and analyzed using
TCAD simulator. The proposed ESD protection circuit verified
effective low voltage ESD characteristics with low trigger voltage and
high holding voltage.
Abstract: In this paper we present the first Arabic sentence
dataset for on-line handwriting recognition written on tablet pc. The
dataset is natural, simple and clear. Texts are sampled from daily
newspapers. To collect naturally written handwriting, forms are
dictated to writers. The current version of our dataset includes 154
paragraphs written by 48 writers. It contains more than 3800 words
and more than 19,400 characters. Handwritten texts are mainly
written by researchers from different research centers. In order to use
this dataset in a recognition system word extraction is needed. In this
paper a new word extraction technique based on the Arabic
handwriting cursive nature is also presented. The technique is applied
to this dataset and good results are obtained. The results can be
considered as a bench mark for future research to be compared with.
Abstract: Rough set theory is a very effective tool to deal with granularity and vagueness in information systems. Covering-based rough set theory is an extension of classical rough set theory. In this paper, firstly we present the characteristics of the reducible element and the minimal description covering-based rough sets through downsets. Then we establish lattices and topological spaces in coveringbased rough sets through down-sets and up-sets. In this way, one can investigate covering-based rough sets from algebraic and topological points of view.
Abstract: The performance of Advection Upstream Splitting
Method AUSM schemes are evaluated against experimental flow
fields at different Mach numbers and results are compared with
experimental data of subsonic, supersonic and hypersonic flow fields.
The turbulent model used here is SST model by Menter. The
numerical predictions include lift coefficient, drag coefficient and
pitching moment coefficient at different mach numbers and angle of
attacks. This work describes a computational study undertaken to
compute the Aerodynamic characteristics of different air vehicles
configurations using a structured Navier-Stokes computational
technique. The CFD code bases on the idea of upwind scheme for the
convective (convective-moving) fluxes. CFD results for GLC305
airfoil and cone cylinder tail fined missile calculated on above
mentioned turbulence model are compared with the available data.
Wide ranges of Mach number from subsonic to hypersonic speeds are
simulated and results are compared. When the computation is done
by using viscous turbulence model the above mentioned coefficients
have a very good agreement with the experimental values. AUSM
scheme is very efficient in the regions of very high pressure gradients
like shock waves and discontinuities. The AUSM versions simulate
the all types of flows from lower subsonic to hypersonic flow without
oscillations.
Abstract: In the last decade, carbohydrates have attracted great
attention as renewable resources for the chemical industry.
Carbohydrates are abundantly found in nature in the form of
monomers, oligomers and polymers, or as components of
biopolymers and other naturally occurring substances. As natural
products, they play important roles in conferring certain physical,
chemical, and biological properties to their carrier molecules.The
synthesis of this particular carbohydrate glycomonomer is part of our
work to obtain biodegradable polymers. Our current paper describes
the synthesis and characterization of a novel carbohydrate
glycomonomer starting from D-glucose, in several synthesis steps,
that involve the protection/deprotection of the D-glucose ring via
acetylation, tritylation, then selective deprotection of the aromaticaliphatic
protective group, in order to obtain 1,2,3,4-tetra-O-acetyl-
6-O-allyl-β-D-glucopyranose. The glycomonomer was then obtained
by the allylation in drastic conditions of 1,2,3,4-tetra-O-acetyl-6-Oallyl-
β-D-glucopyranose with allylic alcohol in the presence of
stannic chloride, in methylene chloride, at room temperature. The
proposed structure of the glycomonomer, 2,3,4-tri-O-acetyl-1,6-di-
O-allyl-β-D-glucopyranose, was confirmed by FTIR, NMR and
HPLC-MS spectrometry. This glycomonomer will be further
submitted to copolymerization with certain acrylic or methacrylic
monomers in order to obtain competitive plastic materials for
applications in the biomedical field.
Abstract: A multilayer self organizing neural neural network
(MLSONN) architecture for binary object extraction, guided by a beta
activation function and characterized by backpropagation of errors
estimated from the linear indices of fuzziness of the network output
states, is discussed. Since the MLSONN architecture is designed to
operate in a single point fixed/uniform thresholding scenario, it does
not take into cognizance the heterogeneity of image information in
the extraction process. The performance of the MLSONN architecture
with representative values of the threshold parameters of the beta
activation function employed is also studied. A three layer bidirectional
self organizing neural network (BDSONN) architecture
comprising fully connected neurons, for the extraction of objects from
a noisy background and capable of incorporating the underlying image
context heterogeneity through variable and adaptive thresholding,
is proposed in this article. The input layer of the network architecture
represents the fuzzy membership information of the image scene to
be extracted. The second layer (the intermediate layer) and the final
layer (the output layer) of the network architecture deal with the self
supervised object extraction task by bi-directional propagation of the
network states. Each layer except the output layer is connected to the
next layer following a neighborhood based topology. The output layer
neurons are in turn, connected to the intermediate layer following
similar topology, thus forming a counter-propagating architecture
with the intermediate layer. The novelty of the proposed architecture
is that the assignment/updating of the inter-layer connection weights
are done using the relative fuzzy membership values at the constituent
neurons in the different network layers. Another interesting feature
of the network lies in the fact that the processing capabilities of
the intermediate and the output layer neurons are guided by a beta
activation function, which uses image context sensitive adaptive
thresholding arising out of the fuzzy cardinality estimates of the
different network neighborhood fuzzy subsets, rather than resorting to
fixed and single point thresholding. An application of the proposed
architecture for object extraction is demonstrated using a synthetic
and a real life image. The extraction efficiency of the proposed
network architecture is evaluated by a proposed system transfer index
characteristic of the network.