Abstract: This paper describes the use of by-products as
adsorbents for removing heavy metals from aqueous effluent
solutions. Products of almond skin, walnut shell, saw dust, rice bran
and egg shell were evaluated as metal ion adsorbents in aqueous
solutions. A comparative study was done with commercial adsorbents
like ion exchange resins and activated carbon too. Batch experiments
were investigated to determine the affinity of all of biomasses for,
Cd(ΙΙ), Cr(ΙΙΙ), Ni(ΙΙ), and Pb(ΙΙ) metal ions at pH 5. The rate of
metal ion removal in the synthetic wastewater by the biomass was
evaluated by measuring final concentration of synthetic wastewater.
At a concentration of metal ion (50 mg/L), egg shell adsorbed high
levels (98.6 – 99.7%) of Pb(ΙΙ) and Cr(ΙΙΙ) and walnut shell adsorbed
high levels (35.3 – 65.4%) of Ni(ΙΙ) and Cd(ΙΙ). In this study, it has
been shown that by-products were excellent adsorbents for removal
of toxic ions from wastewater with efficiency comparable to
commercially available adsorbents, but at a reduced cost. Also
statistical studies using Independent Sample t Test and ANOVA Oneway
for statistical comparison between various elements adsorption
showed that there isn’t a significant difference in some elements
adsorption percentage by by-products and commercial adsorbents.
Abstract: Proper selection of welding parameters for getting
excellent weld is a challenge. HAZ simulation helps in identifying
suitable welding parameters like heating rate, cooling rate, peak
temperature, and energy input. In this study, the influence of weld
thermal cycle of heat affected zone (HAZ) is simulated for
Submerged Arc Welding (SAW) using Gleeble ® 3800 thermomechanical
simulator. A (Micro-alloyed) MA steel plate of thickness
18 mm having yield strength 450MPa is used for making test
specimens. Determination of the mechanical properties of weld
simulated specimens including Charpy V-notch toughness and
hardness is performed. Peak temperatures of 1300°C, 1150°C,
1000°C, 900°C, 800°C, heat energy input of 22KJ/cm and preheat
temperatures of 30°C have been used with Rykalin-3D simulation
model. It is found that the impact toughness (75J) is the best for the
simulated HAZ specimen at the peak temperature 900ºC. For parent
steel, impact toughness value is 26.8J at -50°C in transverse
direction.
Abstract: Fuzzy regression models are useful for investigating
the relationship between explanatory variables and responses in fuzzy
environments. To overcome the deficiencies of previous models and
increase the explanatory power of fuzzy data, the graded mean
integration (GMI) representation is applied to determine
representative crisp regression coefficients. A fuzzy regression model
is constructed based on the modified dissemblance index (MDI),
which can precisely measure the actual total error. Compared with
previous studies based on the proposed MDI and distance criterion, the
results from commonly used test examples show that the proposed
fuzzy linear regression model has higher explanatory power and
forecasting accuracy.
Abstract: Forecasting electricity load plays a crucial role regards
decision making and planning for economical purposes. Besides, in
the light of the recent privatization and deregulation of the power
industry, the forecasting of future electricity load turned out to be a
very challenging problem. Empirical data about electricity load
highlights a clear seasonal behavior (higher load during the winter
season), which is partly due to climatic effects. We also emphasize
the presence of load periodicity at a weekly basis (electricity load is
usually lower on weekends or holidays) and at daily basis (electricity
load is clearly influenced by the hour). Finally, a long-term trend may
depend on the general economic situation (for example, industrial
production affects electricity load). All these features must be
captured by the model.
The purpose of this paper is then to build an hourly electricity load
model. The deterministic component of the model requires non-linear
regression and Fourier series while we will investigate the stochastic
component through econometrical tools.
The calibration of the parameters’ model will be performed by
using data coming from the Italian market in a 6 year period (2007-
2012). Then, we will perform a Monte Carlo simulation in order to
compare the simulated data respect to the real data (both in-sample
and out-of-sample inspection). The reliability of the model will be
deduced thanks to standard tests which highlight a good fitting of the
simulated values.
Abstract: Topology optimization technique utilizes constant
element densities as design parameters. Finally, optimal distribution
contours of the material densities between voids (0) and solids (1) in
design domain represent the determination of topology. It means that
regions with element density values become occupied by solids in
design domain, while there are only void phases in regions where no
density values exist. Therefore the void regions of topology
optimization results provide design information to decide appropriate
depositions of web-opening in structure. Contrary to the basic
objective of the topology optimization technique which is to obtain
optimal topology of structures, this present study proposes a new idea
that topology optimization results can be also utilized for decision of
proper web-opening’s position. Numerical examples of linear
elastostatic structures demonstrate efficiency of methodological
design processes using topology optimization in order to determinate
the proper deposition of web-openings.
Abstract: The purposes of this study are 1) to study the frequent
English writing errors of students registering the course: Reading and
Writing English for Academic Purposes II, and 2) to find out the
results of writing error correction by using coded indirect corrective
feedback and writing error treatments. Samples include 28 2nd year
English Major students, Faculty of Education, Suan Sunandha
Rajabhat University. Tool for experimental study includes the lesson
plan of the course; Reading and Writing English for Academic
Purposes II, and tool for data collection includes 4 writing tests of
short texts. The research findings disclose that frequent English
writing errors found in this course comprise 7 types of grammatical
errors, namely Fragment sentence, Subject-verb agreement, Wrong
form of verb tense, Singular or plural noun endings, Run-ons
sentence, Wrong form of verb pattern and Lack of parallel structure.
Moreover, it is found that the results of writing error correction by
using coded indirect corrective feedback and error treatment reveal
the overall reduction of the frequent English writing errors and the
increase of students’ achievement in the writing of short texts with
the significance at .05.
Abstract: Particle swarm optimization (PSO) is becoming one of
the most important swarm intelligent paradigms for solving global
optimization problems. Although some progress has been made to
improve PSO algorithms over the last two decades, additional work
is still needed to balance parameters to achieve better numerical
properties of accuracy, efficiency, and stability. In the optimal
PSO algorithm, the optimal weightings of (√ 5 − 1)/2 and (3 − √5)/2 are used for the cognitive factor and the social factor,
respectively. By the same token, the same optimal weightings have
been applied for intensification searches and diversification searches,
respectively. Perturbation and constriction effects are optimally
balanced. Simulations of the de Jong, the Rosenbrock, and the
Griewank functions show that the optimal PSO algorithm indeed
achieves better numerical properties and outperforms the canonical
PSO algorithm.
Abstract: Cancer affects people globally with breast cancer being a leading killer. Breast cancer is due to the uncontrollable multiplication of cells resulting in a tumour or neoplasm. Tumours are called ‘benign’ when cancerous cells do not ravage other body tissues and ‘malignant’ if they do so. As mammography is an effective breast cancer detection tool at an early stage which is the most treatable stage it is the primary imaging modality for screening and diagnosis of this cancer type. This paper presents an automatic mammogram classification technique using wavelet and Gabor filter. Correlation feature selection is used to reduce the feature set and selected features are classified using different decision trees.
Abstract: The microstructure, mechanical properties and metalgraphic characteristics of Ni plated AlN-Astaloy Cr-M powders were investigated using specimens produced by tube furnace sintering at 1000-1400 °C temperature. A uniform nickel layer on AlN powders was deposited prior to sintering using electroless plating technique. A composite consisting of ternary additions, metallic phase, Ni and ceramic phase AlN within a matrix of Astaloy Cr-M had been prepared under Ar shroud and then tube furnace sintered. The experimental results carried out by using XRD (X-Ray Diffraction) and SEM (Scanning Electron Microscope) for composition (10% AlN-Astaloy Cr-M) 10% Ni at 1400 °C suggest that the best properties as 132.45HB and permittivity were obtained at 1400 °C.
Abstract: There has been discussion if the use of mobile phones causes accidents. We studied workers’ accidents and near accidents related to the use of phones. This study is part of a large cross-sectional study that was carried out on 15,000 working-age Finns. We noticed that there were 4–5 times more close call situations than accidents connected to mobile phones and also work related accidents were fewer than leisure related. There are confusing parameters like the use of mobile phones at work, differences in work content between women and men.
Abstract: This paper describes the design of a pulse generator based on the Programmable System-on-Chip (PSoC) module. In this module, using programmable logic is possible to implement different pulses which are required for ultrasonic applications, either in a single channel or multiple channels. This module can operate with programmable frequencies from 3-74 MHz; its programming may be versatile covering a wide range of ultrasonic applications. It is ideal for low-power ultrasonic applications where PZT or PVDF transducers are used.
Abstract: Due to the higher power loss levels in electronic components, the thermal design of PCBs (Printed Circuit Boards) of an assembled device becomes one of the most important quality factors in electronics. Nonetheless, some of leading causes of the microelectronic component failures are due to higher temperatures, the leakages or thermal-mechanical stress, which is a concern, is the reliability of microelectronic packages. This article presents an experimental approach to measure the junction temperature of exposed pad packages. The implemented solution is in a prototype phase, using a temperature-sensitive parameter (TSP) to measure temperature directly on the die, validating the numeric results provided by the Mechanical APDL (Ansys Parametric Design Language) under same conditions. The physical device-under-test is composed by a Thermal Test Chip (TTC-1002) and assembly in a QFN cavity, soldered to a test-board according to JEDEC Standards. Monitoring the voltage drop across a forward-biased diode, is an indirectly method but accurate to obtain the junction temperature of QFN component with an applied power range between 0,3W to 1.5W. The temperature distributions on the PCB test-board and QFN cavity surface were monitored by an infra-red thermal camera (Goby-384) controlled and images processed by the Xeneth software. The article provides a set-up to monitorize in real-time the junction temperature of ICs, namely devices with the exposed pad package (i.e. QFN). Presenting the PCB layout parameters that the designer should use to improve thermal performance, and evaluate the impact of voids in solder interface in the device junction temperature.
Abstract: In this paper, we propose an improved face recognition algorithm using histogram-based features in spatial and frequency domains. For adding spatial information of the face to improve recognition performance, a region-division (RD) method is utilized. The facial area is firstly divided into several regions, then feature vectors of each facial part are generated by Binary Vector Quantization (BVQ) histogram using DCT coefficients in low frequency domains, as well as Local Binary Pattern (LBP) histogram in spatial domain. Recognition results with different regions are first obtained separately and then fused by weighted averaging. Publicly available ORL database is used for the evaluation of our proposed algorithm, which is consisted of 40 subjects with 10 images per subject containing variations in lighting, posing, and expressions. It is demonstrated that face recognition using RD method can achieve much higher recognition rate.
Abstract: The nonlinear static and dynamic analysis procedures
presented in EN 1998-1 for the structural response of a RC wall-frame
building are assessed. The structure is designed according to the guidelines for
high ductility (DCH) in 1998-1. The finite element packages SeismoStruct and
OpenSees are utilized and evaluated. The structural response remains nearly
in the elastic range even though the building was designed for high ductility.
The overstrength is a result of oversized and heavily reinforced members,
with emphasis on the lower storey walls. Nonlinear response history analysis
in the software packages give virtually identical results for displacements.
Abstract: Evolutionary Fuzzy PID Speed Controller for Permanent Magnet Synchronous Motor (PMSM) is developed to achieve the Speed control of PMSM in Closed Loop operation and to deal with the existence of transients. Consider a Fuzzy PID control design problem, based on common control Engineering Knowledge. If the transient error is big, that Good transient performance can be obtained by increasing the P and I gains and decreasing the D gains. To autotune the control parameters of the Fuzzy PID controller, the Evolutionary Algorithms (EA) are developed. EA based Fuzzy PID controller provides better speed control and guarantees the closed loop stability. The Evolutionary Fuzzy PID controller can be implemented in real time Applications without any concern about instabilities that leads to system failure or damage.
Abstract: Colorectal cancer (CRC) is one of the most prevalent cancers and intestinal microbial community plays an important role in colorectal tumorigenesis. Probiotics have recently been assessed as effective anti-proliferative agents and thus this study was performed to examine whether CRC undergo apoptosis by treating with isolated Iranian native dairy yeast, Kluyveromyces marxianus YAS, secretion metabolites. The cytotoxicity assessments on cells (HT-29, Caco-2) were accomplished through 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assay as well as qualitative DAPI (4',6-diamidino-2-phenylindole staining) and quantitative (flow cytometry assessments) evaluations of apoptosis. To evaluate the main mechanism of apoptosis, Real time PCR method was applied. Kluyveromyces marxianus YAS secretions (IC50) showed significant cytotoxicity against HT-29 and Caco-2 cancer cell lines (66.57 % and 66.34 % apoptosis) similar to 5-Fluorouracil (5-FU) while apoptosis only was developed in 27.57 % of KDR normal cells. The prophylactic effects of Kluyveromyces marxianus (PTCC 5195), as a reference yeast, was not similar to Kluyveromyces marxianus YAS indicating strain dependency of bioactivities on CRC disease prevention. Based on real time PCR results, the main cytotoxicity is related to apoptosis phenomenon and the core related mechanism is depended on the overexpression of BAX, CASP 9, CASP 8 and CASP 3 inducing apoptosis genes. However, several investigations should be conducted to precisely determine the effective compounds to be used as anticancer therapeutics in the future.
Abstract: Online Social Networks (OSNs) are nowadays being used widely and intensively for crime investigation and prevention activities. As they provide a lot of information they are used by the law enforcement and intelligence. An extensive review on existing solutions and models for collecting intelligence from this source of information and making use of it for solving crimes has been presented in this article. The main focus is on smart solutions and models where ontologies have been used as the main approach for representing criminal domain knowledge. A framework for a prototype ontology named SC-Ont will be described. This defines terms of the criminal domain ontology and the relations between them. The terms and the relations are extracted during both this review and the discussions carried out with domain experts. The development of SC-Ont is still ongoing work, where in this paper, we report mainly on the motivation for using smart ontology models and the possible benefits of using them for solving crimes.
Abstract: In this study, the dynamic analysis of viscoelastic plates with variable thickness is examined. The solutions of dynamic response of viscoelastic thin plates with variable thickness have been obtained by using the functional analysis method in the conjunction with the Gâteaux differential. The four-node serendipity element with four degrees of freedom such as deflection, bending, and twisting moments at each node is used. Additionally, boundary condition terms are included in the functional by using a systematic way. In viscoelastic modeling, Three-parameter Kelvin solid model is employed. The solutions obtained in the Laplace-Carson domain are transformed to the real time domain by using MDOP, Dubner & Abate, and Durbin inverse transform techniques. To test the performance of the proposed mixed finite element formulation, numerical examples are treated.
Abstract: Gas lift optimization is becoming more important now a day in petroleum industry. A proper lift optimization can reduce the operating cost, increase the net present value (NPV) and maximize the recovery from the asset. A widely accepted definition of gas lift optimization is to obtain the maximum output under specified operating conditions. In addition, gas lift, a costly and indispensable means to recover oil from high depth reservoir entails solving the gas lift optimization problems. Gas lift optimization is a continuous process; there are two levels of production optimization. The total field optimization involves optimizing the surface facilities and the injection rate that can be achieved by standard tools softwares. Well level optimization can be achieved by optimizing the well parameters such as point of injection, injection rate, and injection pressure. All these aspects have been investigated and presented in this study by using experimental data and PROSPER simulation program. The results show that the well head pressure has a large influence on the gas lift performance and also proved that smart gas lift valve can be used to improve gas lift performance by controlling gas injection from down hole. Obtaining the optimum gas injection rate is important because excessive gas injection reduces production rate and consequently increases the operation cost.
Abstract: We propose two affine projection algorithms (APA)
with variable regularization parameter. The proposed algorithms
dynamically update the regularization parameter that is fixed in the
conventional regularized APA (R-APA) using a gradient descent
based approach. By introducing the normalized gradient, the proposed
algorithms give birth to an efficient and a robust update scheme for
the regularization parameter. Through experiments we demonstrate
that the proposed algorithms outperform conventional R-APA in
terms of the convergence rate and the misadjustment error.