Abstract: The recovery of metal values and safe disposal of
spent catalyst is gaining interest due to both its hazardous nature and
increased regulation associated with disposal methods. Prior to the
recovery of the valuable metals, removal of entrained deposits limit
the diffusion of lixiviate resulting in low recovery of metals must be
taken into consideration. Therefore, petroleum refinery spent catalyst
was subjected to acetone washing and roasting at 500oC. The treated
samples were investigated for metals bioleaching using
Acidithiobacillus ferrooxidans in batch reactors and the leaching
efficiencies were compared. It was found out that acetone washed
spent catalysts results in better metal recovery compare to roasted
spent. About 83% Ni, 20% Al, 50% Mo and 73% V were leached
using the acetone washed spent catalyst. In both the cases, Ni, V and
Mo was high compared to Al.
Abstract: There are several means to measure the oxidation of edible oils, such as the acid value, the peroxide value, and the anisidine value. However, these means require large quantities of reagents and are time-consuming tasks. Therefore, a more convenient and time-saving way to measure the oxidation of edible oils is required. In this report, an edible oil condition sensor was fabricated by using single-walled nanotubes (SWNT). In order to test the sensor, oxidized edible oils, each one at a different acid value, were prepared. The SWNT sensors were immersed into these oxidized oils and the resistance changes in the sensors were measured. It was found that the conductivity of the sensors decreased as the oxidation level of oil increased. This result suggests that a change of the oil components induced by the oxidation process in edible oils is related to the conductivity change in the SWNT sensor.
Abstract: Optimizing equipment selection in heavy earthwork
operations is a critical key in the success of any construction project.
The objective of this research incentive was geared towards
developing a computer model to assist contractors and construction
managers in estimating the cost of heavy earthwork operations.
Economical operation analysis was conducted for an equipment fleet
taking into consideration the owning and operating costs involved in
earthwork operations. The model is being developed in a Microsoft
environment and is capable of being integrated with other estimating
and optimization models. In this study, Caterpillar® Performance
Handbook [5] was the main resource used to obtain specifications of
selected equipment. The implementation of the model shall give
optimum selection of equipment fleet not only based on cost
effectiveness but also in terms of versatility. To validate the model, a
case study of an actual dam construction project was selected to
quantify its degree of accuracy.
Abstract: The presence of a vertical fatigue crack in the web of
a plate girder subjected to pure bending influences the bending
moment capacity of the girder. The growth of the crack may lead to
premature elastic failure due to flange local yielding, flange local
buckling, or web local buckling. Approximate expressions for the
bending moment capacities corresponding to these failure modes
were formulated. Finite element analyses were then used to validate
the expressions. The expressions were employed to assess the effects
of crack length on the capacity. Neglecting brittle fracture, tension
buckling, and ductile failure modes, it was found that typical girders
are governed by the capacity associated with flange local yielding as
influenced by the crack. Concluding, a possible use of the capacity
expressions in girder design was demonstrated.
Abstract: In this paper, we consider a multi user multiple input
multiple output (MU-MIMO) based cooperative reporting system for
cognitive radio network. In the reporting network, the secondary
users forward the primary user data to the common fusion center
(FC). The FC is equipped with linear equalizers and an energy
detector to make the decision about the spectrum. The primary user
data are considered to be a digital video broadcasting - terrestrial
(DVB-T) signal. The sensing channel and the reporting channel are
assumed to be an additive white Gaussian noise and an independent
identically distributed Raleigh fading respectively. We analyzed the
detection probability of MU-MIMO system with linear equalizers and
arrived at the closed form expression for average detection
probability. Also the system performance is investigated under
various MIMO scenarios through Monte Carlo simulations.
Abstract: Speckle noise affects all coherent imaging systems
including medical ultrasound. In medical images, noise suppression
is a particularly delicate and difficult task. A tradeoff between noise
reduction and the preservation of actual image features has to be made
in a way that enhances the diagnostically relevant image content.
Even though wavelets have been extensively used for denoising
speckle images, we have found that denoising using contourlets gives
much better performance in terms of SNR, PSNR, MSE, variance and
correlation coefficient. The objective of the paper is to determine the
number of levels of Laplacian pyramidal decomposition, the number
of directional decompositions to perform on each pyramidal level and
thresholding schemes which yields optimal despeckling of medical
ultrasound images, in particular. The proposed method consists of the
log transformed original ultrasound image being subjected to contourlet
transform, to obtain contourlet coefficients. The transformed
image is denoised by applying thresholding techniques on individual
band pass sub bands using a Bayes shrinkage rule. We quantify the
achieved performance improvement.
Abstract: This paper proposes an active soft-switching circuit for
bridge converters aiming to improve the power conversion efficiency.
The proposed circuit achieves loss-less switching for both main and
auxiliary switches without increasing the main switch current/voltage
rating. A winding coupled to the primary of power transformer
ensures ZCS for the auxiliary switches during their turn-off. A 350 W,
100 kHz phase shifted full bridge (PSFB) converter is built to validate
the analysis and design. Theoretical loss calculations for proposed
circuit is presented. The proposed circuit is compared with passive
soft switched PSFB in terms of efficiency and loss in duty cycle.
Abstract: In theoretical computer science, the Turing machine has played a number of important roles in understanding and exploiting basic concepts and mechanisms in computing and information processing [20]. It is a simple mathematical model of computers [9]. After that, M.Blum and C.Hewitt first proposed two-dimensional automata as a computational model of two-dimensional pattern processing, and investigated their pattern recognition abilities in 1967 [7]. Since then, a lot of researchers in this field have been investigating many properties about automata on a two- or three-dimensional tape. On the other hand, the question of whether processing fourdimensional digital patterns is much more difficult than two- or threedimensional ones is of great interest from the theoretical and practical standpoints. Thus, the study of four-dimensional automata as a computasional model of four-dimensional pattern processing has been meaningful [8]-[19],[21]. This paper introduces a cooperating system of four-dimensional finite automata as one model of four-dimensional automata. A cooperating system of four-dimensional finite automata consists of a finite number of four-dimensional finite automata and a four-dimensional input tape where these finite automata work independently (in parallel). Those finite automata whose input heads scan the same cell of the input tape can communicate with each other, that is, every finite automaton is allowed to know the internal states of other finite automata on the same cell it is scanning at the moment. In this paper, we mainly investigate some accepting powers of a cooperating system of eight- or seven-way four-dimensional finite automata. The seven-way four-dimensional finite automaton is an eight-way four-dimensional finite automaton whose input head can move east, west, south, north, up, down, or in the fu-ture, but not in the past on a four-dimensional input tape.
Abstract: The IDR(s) method based on an extended IDR theorem was proposed by Sonneveld and van Gijzen. The original IDR(s) method has excellent property compared with the conventional iterative methods in terms of efficiency and small amount of memory. IDR(s) method, however, has unexpected property that relative residual 2-norm stagnates at the level of less than 10-12. In this paper, an effective strategy for stagnation detection, stagnation avoidance using adaptively information of parameter s and improvement of convergence rate itself of IDR(s) method are proposed in order to gain high accuracy of the approximated solution of IDR(s) method. Through numerical experiments, effectiveness of adaptive tuning IDR(s) method is verified and demonstrated.
Abstract: Cryptography, Image watermarking and E-banking are
filled with apparent oxymora and paradoxes. Random sequences are
used as keys to encrypt information to be used as watermark during
embedding the watermark and also to extract the watermark during
detection. Also, the keys are very much utilized for 24x7x365
banking operations. Therefore a deterministic random sequence is
very much useful for online applications. In order to obtain the same
random sequence, we need to supply the same seed to the generator.
Many researchers have used Deterministic Random Number
Generators (DRNGs) for cryptographic applications and Pseudo
Noise Random sequences (PNs) for watermarking. Even though,
there are some weaknesses in PN due to attacks, the research
community used it mostly in digital watermarking. On the other hand,
DRNGs have not been widely used in online watermarking due to its
computational complexity and non-robustness. Therefore, we have
invented a new design of generating DRNG using Pi-series to make it
useful for online Cryptographic, Digital watermarking and Banking
applications.
Abstract: Passive systems were born with the purpose of the
greatest exploitation of solar energy in cold climates and high
altitudes. They spread themselves until the 80-s all over the world
without any attention to the specific climate and the summer
behavior; this caused the deactivation of the systems due to a series
of problems connected to the summer overheating, the complex
management and the rising of the dust.
Until today the European regulation limits only the winter
consumptions without any attention to the summer behavior but, the
recent European EN 15251 underlines the relevance of the indoor
comfort, and the necessity of the analytic studies validation by
monitoring case studies.
In the porpose paper we demonstrate that the solar wall is an
efficient system both from thermal comfort and energy saving point
of view and it is the most suitable for our temperate climates because
it can be used as a passive cooling sistem too. In particular the paper
present an experimental and numerical analisys carried out on a case
study with nine different solar passive systems in Ancona, Italy.
We carried out a detailed study of the lodging provided by the
solar wall by the monitoring and the evaluation of the indoor
conditions.
Analyzing the monitored data, on the base of recognized models
of comfort (ISO, ASHRAE, Givoni-s BBCC), is emerged that the
solar wall has an optimal behavior in the middle seasons. In winter
phase this passive system gives more advantages in terms of energy
consumptions than the other systems, because it gives greater heat
gain and therefore smaller consumptions. In summer, when outside
air temperature return in the mean seasonal value, the indoor comfort
is optimal thanks to an efficient transversal ventilation activated from
the same wall.
Abstract: A steady two-phase flow model has been developed to simulate the drying process of porous particle in a pneumatic conveying dryer. The model takes into account the momentum, heat and mass transfer between the continuous phase and the dispersed phase. A single particle model was employed to calculate the evaporation rate. In this model the pore structure is simplified to allow the dominant evaporation mechanism to be readily identified at all points within the duct. The predominant mechanism at any time depends upon the pressure, temperature and the diameter of pore from which evaporating is occurring. The model was validated against experimental studies of pneumatic transport at low and high speeds as well as pneumatic drying. The effects of operating conditions on the dryer parameters are studied numerically. The present results show that the drying rate is enhanced as the inlet gas temperature and the gas flow rate increase and as the solid mass flow rate deceases. The present results also demonstrate the necessity of measuring the inlet gas velocity or the solid concentration in any experimental analysis.
Abstract: This research is to design and implement a new kind
of agitators called differential agitator. The Differential Agitator is an
electro- mechanic set consists of two shafts. The first shaft is the
bearing axis while the second shaft is the axis of the quartet upper
bearing impellers group and the triple lower group which are called
as agitating group. The agitating group is located inside a cylindrical
container equipped especially to contain square directors for the
liquid entrance and square directors called fixing group for the liquid
exit. The fixing group is installed containing the agitating group
inside any tank whether from upper or lower position. The agitating
process occurs through the agitating group bearing causing a lower
pressure over the upper group leading to withdrawing the liquid from
the square directors of the liquid entering and consequently the liquid
moves to the denser place under the quartet upper group. Then, the
liquid moves to the so high pressure area under the agitating group
causing the liquid to exit from the square directors in the bottom of
the container. For improving efficiency, parametric study and shape
optimization has been carried out. A numerical analysis,
manufacturing and laboratory experiments were conducted to design
and implement the differential agitator. Knowing the material
prosperities and the loading conditions, the FEM using ANSYS11
was used to get the optimum design of the geometrical parameters of
the differential agitator elements while the experimental test was
performed to validate the advantages of the differential agitators to
give a high agitation performance of lime in the water as an example.
In addition, the experimental work has been done to express the
internal container shape in the agitation efficiency. The study ended
up with conclusions to maximize agitator performance and optimize
the geometrical parameters to be used for manufacturing the
differential agitator
Abstract: Children and adolescents developing in the worlds of today are facing a getting array of new and old challenges. School counselling is improving rapidly in contemporary education systems around the world. It can be said that counselling system in Turkey was newly borning. In this study, “Family of the Blood" activity is improved with respect to compherensive guidance school program. The sample included 22 adolescents who were high school students. The activity was carried out in 4 sessions, each of which lasted 45 minutes. In the first session, students- personal-social needs were determined. In the second session, in order to warm up, the students were asked three questions consisting of the constructional aspect. In the third session, the counselor and the teacher shared the results of students- responses obtained in the previous session. In the fourth session, the tables formed by students were presented in the classroom. In order to evaluate the activity, three questions were asked of the teacher and counselor. According to the results, the lesson aims of curriculum and counselling aims of curriculum were attained. In the light of literature, the results were discussed and some suggestions were made. It is taken into consideration that the activitiy was beneficial in many respects, similar studies should be carried out in the near future.
Abstract: Total liquid ventilation can support gas exchange in animal models of lung injury. Clinical application awaits further technical improvements and performance verification. Our aim was to develop a liquid ventilator, able to deliver accurate tidal volumes, and a computerized system for measuring lung mechanics. The computer-assisted, piston-driven respirator controlled ventilatory parameters that were displayed and modified on a real-time basis. Pressure and temperature transducers along with a lineal displacement controller provided the necessary signals to calculate lung mechanics. Ten newborn lambs (
Abstract: Silver nanoparticles were prepared by chemical reduction method. Silver nitrate was taken as the metal precursor and hydrazine hydrate as a reducing agent. The formation of the silver nanoparticles was monitored using UV-Vis absorption spectroscopy. The UV-Vis spectroscopy revealed the formation of silver nanopart├¡cles by exhibing the typical surface plasmon absorption maxima at 418-420 nm from the UV–Vis spectrum. Comparison of theoretical (Mie light scattering theory) and experimental results showed that diameter of silver nanoparticles in colloidal solution is about 60 nm. We have used energy-dispersive spectroscopy (EDX), X-ray diffraction (XRD), transmission electron microscopy (TEM) and, UV–Vis spectroscopy to characterize the nanoparticles obtained. The energy-dispersive spectroscopy (EDX) of the nanoparticles dispersion confirmed the presence of elemental silver signal no peaks of other impurity were detected. The average size and morphology of silver nanoparticles were determined by transmission electron microscopy (TEM). TEM photographs indicate that the nanopowders consist of well dispersed agglomerates of grains with a narrow size distribution (40 and 60 nm), whereas the radius of the individual particles are between 10 and 20 nm. The synthesized nanoparticles have been structurally characterized by X-ray diffraction and transmission high-energy electron diffraction (HEED). The peaks in the XRD pattern are in good agreement with the standard values of the face-centered-cubic form of metallic silver (ICCD-JCPDS card no. 4-0787) and no peaks of other impurity crystalline phases were detected. Additionally, the antibacterial activity of the nanopart├¡culas dispersion was measured by Kirby-Bauer method. The nanoparticles of silver showed high antimicrobial and bactericidal activity against gram positive bacteria such as Escherichia Coli, Pseudimonas aureginosa and staphylococcus aureus which is a highly methicillin resistant strain.
Abstract: There has been a growing emphasis in
communication management from simple coordination of
promotional tools to a complex strategic process. This study will
examine the current marketing communications and engagement
strategies used in addressing the key stakeholders. In the case of
fertilizer industry in Malaysia, there has been little empirical
research on stakeholder communication when major challenges
facing the modern corporation is the need to communicate its
identity, its values and products in order to distinguish itself from
competitors. The study will employ both quantitative and qualitative
methods and the use of Structural Equation Modeling (SEM) to
establish a causal relationship amongst the key factors of stakeholder
communication strategies and increment in consumers-
choice/acceptance and impact on financial performance. One of the
major contributions is a conceptual framework for communication
strategies and engagement in increasing consumers- acceptance level
and the firm-s financial performance.
Abstract: This study aims to examine the factors affecting
knowledge sharing behavior in knowledge-based electronic communities (e-communities) because quantity and quality of
knowledge shared among the members play a critical role in the community-s sustainability. Past research has suggested three
perspectives that may affect the quantity and quality of knowledge
shared: economics, social psychology, and social ecology. In this
study, we strongly believe that an economic perspective may be suitable to validate factors influencing newly registered members-
knowledge contribution at the beginning of relationship development.
Accordingly, this study proposes a model to validate the factors influencing members- knowledge sharing based on Transaction Cost
Theory. By doing so, we may empirically test our hypotheses in various types of e-communities to determine the generalizability of our research models.
Abstract: The objective of the present study was to examine the
dose-response relationships between antioxidant parameters and liver
contaminant levels of Kazakhstan light crude oil (KLCO) in albino
rats. The animals were repeatedly exposed, by intraperitoneal
injection, to low dosages (0.5–1.5 ml/kg) of KLCO. Rats exposed to
these doses levels did not show any apparent symptoms of
intoxication. Serum aminotransferases increased significantly
(p
Abstract: In recent years, there has been an increasing interest in using daylight to save energy in buildings. In tropical regions, daylighting is always an energy saver. On the other hand, daylight provides visual comfort. According to standards, it shows that many criteria should be taken into consideration in order to have daylight utilization and visual comfort. The current standard in Malaysia, MS 1525 does not provide sufficient guideline. Hence, more research is needed on daylight performance. If architects do not consider daylight design, it not only causes inconvenience in working spaces but also causes more energy consumption as well as environmental pollution. This research had surveyed daylight performance in 5 selected office buildings from different area of Malaysian through experimental method. Several parameters of daylight quality such as daylight factor, surface luminance and surface luminance ratio were measured in different rooms in each building. The result of this research demonstrated that most of the buildings were not designed for daylight utilization. Therefore, it is very important that architects follow the daylight design recommendation to reduce consumption of electric power for artificial lighting while the sufficient quality of daylight is available.