Abstract: Fischer-Tropsch synthesis is one of the most
important catalytic reactions that convert the synthetic gas to light
and heavy hydrocarbons. One of the main issues is selecting the type
of reactor. The slurry bubble reactor is suitable choice for Fischer-
Tropsch synthesis because of its good qualification to transfer heat
and mass, high durability of catalyst, low cost maintenance and
repair. The more common catalysts for Fischer-Tropsch synthesis are
Iron-based and Cobalt-based catalysts, the advantage of these
catalysts on each other depends on which type of hydrocarbons we
desire to produce. In this study, Fischer-Tropsch synthesis is modeled
with Iron and Cobalt catalysts in a slurry bubble reactor considering
mass and momentum balance and the hydrodynamic relations effect
on the reactor behavior. Profiles of reactant conversion and reactant
concentration in gas and liquid phases were determined as the
functions of residence time in the reactor. The effects of temperature,
pressure, liquid velocity, reactor diameter, catalyst diameter, gasliquid
and liquid-solid mass transfer coefficients and kinetic
coefficients on the reactant conversion have been studied. With 5%
increase of liquid velocity (with Iron catalyst), H2 conversions
increase about 6% and CO conversion increase about 4%, With 8%
increase of liquid velocity (with Cobalt catalyst), H2 conversions
increase about 26% and CO conversion increase about 4%. With
20% increase of gas-liquid mass transfer coefficient (with Iron
catalyst), H2 conversions increase about 12% and CO conversion
increase about 10% and with Cobalt catalyst H2 conversions increase
about 10% and CO conversion increase about 6%. Results show that
the process is sensitive to gas-liquid mass transfer coefficient and
optimum condition operation occurs in maximum possible liquid
velocity. This velocity must be more than minimum fluidization
velocity and less than terminal velocity in such a way that avoid
catalysts particles from leaving the fluidized bed.
Abstract: Sparse representation which can represent high dimensional
data effectively has been successfully used in computer vision
and pattern recognition problems. However, it doesn-t consider the
label information of data samples. To overcome this limitation,
we develop a novel dimensionality reduction algorithm namely
dscriminatively regularized sparse subspace learning(DR-SSL) in this
paper. The proposed DR-SSL algorithm can not only make use of
the sparse representation to model the data, but also can effective
employ the label information to guide the procedure of dimensionality
reduction. In addition,the presented algorithm can effectively deal
with the out-of-sample problem.The experiments on gene-expression
data sets show that the proposed algorithm is an effective tool for
dimensionality reduction and gene-expression data classification.
Abstract: In this paper, an accurate theoretical analysis for the achievable average channel capacity (in the Shannon sense) per user of a hybrid cellular direct-sequence/fast frequency hopping code-division multiple-access (DS/FFH-CDMA) system operating in a Rayleigh fading environment is presented. The analysis covers the downlink operation and leads to the derivation of an exact mathematical expression between the normalized average channel capacity available to each system-s user, under simultaneous optimal power and rate adaptation and the system-s parameters, as the number of hops per bit, the processing gain applied, the number of users per cell and the received signal-tonoise power ratio over the signal bandwidth. Finally, numerical results are presented to illustrate the proposed mathematical analysis.
Abstract: The present work encounters the solution of the defect identification problem with the use of an evolutionary algorithm combined with a simplex method. In more details, a Matlab implementation of Genetic Algorithms is combined with a Simplex method in order to lead to the successful identification of the defect. The influence of the location and the orientation of the depressed ellipsoidal flaw was investigated as well as the use of different amount of static data in the cost function. The results were evaluated according to the ability of the simplex method to locate the global optimum in each test case. In this way, a clear impression regarding the performance of the novel combination of the optimization algorithms, and the influence of the geometrical parameters of the flaw in defect identification problems was obtained.
Abstract: In the present work steady inviscid hypersonic flows
are calculated by approximate Method. Maslens' inverse method is the chosen approximate method. For the inverse problem, parabolic
shock shape is chosen for the two-dimensional flow, and the body shape and flow field are calculated using Maslen's method. For the axisymmetric inverse problem paraboloidal shock is chosen and the
surface distribution of pressure is obtained.
Abstract: In this paper, the statistical properties of filtered or convolved signals are considered by deriving the resulting density functions as well as the exact mean and variance expressions given a prior knowledge about the statistics of the individual signals in the filtering or convolution process. It is shown that the density function after linear convolution is a mixture density, where the number of density components is equal to the number of observations of the shortest signal. For circular convolution, the observed samples are characterized by a single density function, which is a sum of products.
Abstract: This paper proposes an improvement method of classification
efficiency in a classification model. The model is used
in a risk search system and extracts specific labels from articles
posted at bulletin board sites. The system can analyze the important
discussions composed of the articles. The improvement method
introduces ensemble learning methods that use multiple classification
models. Also, it introduces expressions related to the specific labels
into generation of word vectors. The paper applies the improvement
method to articles collected from three bulletin board sites selected
by users and verifies the effectiveness of the improvement method.
Abstract: Artifact free photoplethysmographic (PPG) signals are
necessary for non-invasive estimation of oxygen saturation (SpO2) in
arterial blood. Movement of a patient corrupts the PPGs with motion
artifacts, resulting in large errors in the computation of Sp02. This
paper presents a study on using Kalman Filter in an innovative way
by modeling both the Artillery Blood Pressure (ABP) and the
unwanted signal, additive motion artifact, to reduce motion artifacts
from corrupted PPG signals. Simulation results show acceptable
performance regarding LMS and variable step LMS, thus
establishing the efficacy of the proposed method.
Abstract: Quality Function Deployment (QFD) is an expounded, multi-step planning method for delivering commodity, services, and processes to customers, both external and internal to an organization. It is a way to convert between the diverse customer languages expressing demands (Voice of the Customer), and the organization-s languages expressing results that sate those demands. The policy is to establish one or more matrices that inter-relate producer and consumer reciprocal expectations. Due to its visual presence is called the “House of Quality" (HOQ). In this paper, we assumed HOQ in multi attribute decision making (MADM) pattern and through a proposed MADM method, rank technical specifications. Thereafter compute satisfaction degree of customer requirements and for it, we apply vagueness and uncertainty conditions in decision making by fuzzy set theory. This approach would propound supervised neural network (perceptron) for MADM problem solving.
Abstract: Gene, principal unit of inheritance, is an ordered
sequence of nucleotides. The genes of eukaryotic organisms include
alternating segments of exons and introns. The region of
Deoxyribonucleic acid (DNA) within a gene containing instructions
for coding a protein is called exon. On the other hand, non-coding
regions called introns are another part of DNA that regulates gene
expression by removing from the messenger Ribonucleic acid (RNA)
in a splicing process. This paper proposes to determine splice
junctions that are exon-intron boundaries by analyzing DNA
sequences. A splice junction can be either exon-intron (EI) or intron
exon (IE). Because of the popularity and compatibility of the
artificial neural network (ANN) in genetic fields; various ANN
models are applied in this research. Multi-layer Perceptron (MLP),
Radial Basis Function (RBF) and Generalized Regression Neural
Networks (GRNN) are used to analyze and detect the splice junctions
of gene sequences. 10-fold cross validation is used to demonstrate
the accuracy of networks. The real performances of these networks
are found by applying Receiver Operating Characteristic (ROC)
analysis.
Abstract: The three-time-scale plant model of a wind power
generator, including a wind turbine, a flexible vertical shaft, a Variable
Inertia Flywheel (VIF) module, an Active Magnetic Bearing (AMB)
unit and the applied wind sequence, is constructed. In order to make
the wind power generator be still able to operate as the spindle speed
exceeds its rated speed, the VIF is equipped so that the spindle speed
can be appropriately slowed down once any stronger wind field is
exerted. To prevent any potential damage due to collision by shaft
against conventional bearings, the AMB unit is proposed to regulate
the shaft position deviation. By singular perturbation order-reduction
technique, a lower-order plant model can be established for the
synthesis of feedback controller. Two major system parameter
uncertainties, an additive uncertainty and a multiplicative uncertainty,
are constituted by the wind turbine and the VIF respectively.
Frequency Shaping Sliding Mode Control (FSSMC) loop is proposed
to account for these uncertainties and suppress the unmodeled
higher-order plant dynamics. At last, the efficacy of the FSSMC is
verified by intensive computer and experimental simulations for
regulation on position deviation of the shaft and counter-balance of
unpredictable wind disturbance.
Abstract: The main focus of the work was concerned with hydrodynamic and thermal analysis of the plate heat exchanger channel with corrugation patterns suggested to be triangular, sinusoidal, and square corrugation. This study was to numerically model and validate the triangular corrugated channel with dimensions/parameters taken from open literature, and then model/analyze both sinusoidal, and square corrugated channel referred to the triangular model. Initially, 2D modeling with local extensive analysis for triangular corrugated channel was carried out. By that, all local pressure drop, wall shear stress, friction factor, static temperature, heat flux, Nusselt number, and surface heat coefficient, were analyzed to interpret the hydrodynamic and thermal phenomena occurred in the flow. Furthermore, in order to facilitate confidence in this model, a comparison between the values predicted, and experimental results taken from literature for almost the same case, was done. Moreover, a holistic numerical study for sinusoidal and square channels together with global comparisons with triangular corrugation under the same condition, were handled. Later, a comparison between electric, and fluid cooling through varying the boundary condition was achieved. The constant wall temperature and constant wall heat flux boundary conditions were employed, and the different resulted Nusselt numbers as a consequence were justified. The results obtained can be used to come up with an optimal design, a 'compromise' between heat transfer and pressure drop.
Abstract: The study of the transport coefficients in electronic
devices is currently carried out by analytical and empirical models.
This study requires several simplifying assumptions, generally
necessary to lead to analytical expressions in order to study the
different characteristics of the electronic silicon-based devices.
Further progress in the development, design and optimization of
Silicon-based devices necessarily requires new theory and modeling
tools. In our study, we use the PSO (Particle Swarm Optimization)
technique as a computational tool to develop analytical approaches in
order to study the transport phenomenon of the electron in crystalline
silicon as function of temperature and doping concentration. Good
agreement between our results and measured data has been found.
The optimized analytical models can also be incorporated into the
circuits simulators to study Si-based devices without impact on the
computational time and data storage.
Abstract: The algorithm represents the DCT coefficients to concentrate signal energy and proposes combination and dictator to eliminate the correlation in the same level subband for encoding the DCT-based images. This work adopts DCT and modifies the SPIHT algorithm to encode DCT coefficients. The proposed algorithm also provides the enhancement function in low bit rate in order to improve the perceptual quality. Experimental results indicate that the proposed technique improves the quality of the reconstructed image in terms of both PSNR and the perceptual results close to JPEG2000 at the same bit rate.
Abstract: The influence of axial magnetic field (B=0.48 T) on
the variation of ionization efficiency coefficient h and secondary
electron emission coefficient g with respect to reduced electric field
E/P is studied at a new range of plane-parallel electrode spacing (0<
d< 20 cm) and different nitrogen working pressure between 0.5-20
Pa. The axial magnetic field is produced from an inductive copper
coil of radius 5.6 cm. The experimental data of breakdown voltage is
adopted to estimate the mean Paschen curves at different working
features. The secondary electron emission coefficient is calculated
from the mean Paschen curve and used to determine the minimum
breakdown voltage. A reduction of discharge voltage of about 25% is
investigated by the applied of axial magnetic field. At high interelectrode
spacing, the effect of axial magnetic field becomes more
significant for the obtained values of h but it was less for the values
of g.
Abstract: In designing of condensers, the prediction of pressure
drop is as important as the prediction of heat transfer coefficient.
Modeling of two phase flow, particularly liquid – vapor flow under
diabatic conditions inside a horizontal tube using CFD analysis is
difficult with the available two phase models in FLUENT due to
continuously changing flow patterns. In the present analysis, CFD
analysis of two phase flow of refrigerants inside a horizontal tube of
inner diameter, 0.0085 m and 1.2 m length is carried out using
homogeneous model under adiabatic conditions. The refrigerants
considered are R22, R134a and R407C. The analysis is performed at
different saturation temperatures and at different flow rates to
evaluate the local frictional pressure drop. Using Homogeneous
model, average properties are obtained for each of the refrigerants
that is considered as single phase pseudo fluid. The so obtained
pressure drop data is compared with the separated flow models
available in literature.
Abstract: This paper presents the experimental results of a
single cylinder Enfield engine using an electronically controlled fuel
injection system which was developed to carry out exhaustive tests
using neat CNG, and mixtures of hydrogen in compressed natural gas
(HCNG) as 0, 5, 10, 15 and 20% by energy. Experiments were
performed at 2000 and 2400 rpm with wide open throttle and varying
the equivalence ratio. Hydrogen which has fast burning rate, when
added to compressed natural gas, enhances its flame propagation rate.
The emissions of HC, CO, decreased with increasing percentage of
hydrogen but NOx was found to increase. The results indicated a
marked improvement in the brake thermal efficiency with the
increase in percentage of hydrogen added. The improved thermal
efficiency was clearly observed to be more in lean region as
compared to rich region. This study is expected to reduce vehicular
emissions along with increase in thermal efficiency and thus help in
reduction of further environmental degradation.
Abstract: carbonylation of methanol in homogenous phase is
one of the major routesfor production of acetic acid. Amongst group
VIII metal catalysts used in this process iridium has displayed the
best capabilities. To investigate effect of operating parameters like:
temperature, pressure, methyl iodide, methyl acetate, iridium,
ruthenium, and water concentrations on the reaction rate,
experimental design for this system based upon central composite
design (CCD) was utilized. Statistical rate equation developed by this
method contained individual, interactions and curvature effects of
parameters on the reaction rate. The model with p-value less than
0.0001 and R2 values greater than 0.9; confirmeda satisfactory fitness
of the experimental and theoretical studies. In other words, the
developed model and experimental data obtained passed all
diagnostic tests establishing this model as a statistically significant.
Abstract: Multimedia information availability has increased
dramatically with the advent of video broadcasting on handheld
devices. But with this availability comes problems of maintaining the
security of information that is displayed in public. ISMA Encryption
and Authentication (ISMACryp) is one of the chosen technologies for
service protection in DVB-H (Digital Video Broadcasting-
Handheld), the TV system for portable handheld devices. The
ISMACryp is encoded with H.264/AVC (advanced video coding),
while leaving all structural data as it is. Two modes of ISMACryp are
available; the CTR mode (Counter type) and CBC mode (Cipher
Block Chaining) mode. Both modes of ISMACryp are based on 128-
bit AES algorithm. AES algorithms are more complex and require
larger time for execution which is not suitable for real time
application like live TV. The proposed system aims to gain a deep
understanding of video data security on multimedia technologies and
to provide security for real time video applications using selective
encryption for H.264/AVC. Five level of security proposed in this
paper based on the content of NAL unit in Baseline Constrain profile
of H.264/AVC. The selective encryption in different levels provides
encryption of intra-prediction mode, residue data, inter-prediction
mode or motion vectors only. Experimental results shown in this
paper described that fifth level which is ISMACryp provide higher
level of security with more encryption time and the one level provide
lower level of security by encrypting only motion vectors with lower
execution time without compromise on compression and quality of
visual content. This encryption scheme with compression process
with low cost, and keeps the file format unchanged with some direct
operations supported. Simulation was being carried out in Matlab.
Abstract: Experimental data from an atmospheric air/water terrain slugging case has been made available by the Shell Amsterdam research center, and has been subject to numerical simulation and comparison with a one-dimensional two-phase slug tracking simulator under development at the Norwegian University of Science and Technology. The code is based on tracking of liquid slugs in pipelines by use of a Lagrangian grid formulation implemented in Cµ by use of object oriented techniques. An existing hybrid spatial discretization scheme is tested, in which the stratified regions are modelled by the two-fluid model. The slug regions are treated incompressible, thus requiring a single momentum balance over the whole slug. Upon comparison with the experimental data, the period of the simulated severe slugging cycle is observed to be sensitive to slug generation in the horizontal parts of the system. Two different slug initiation methods have been tested with the slug tracking code, and grid dependency has been investigated.