Abstract: Experimental and analytical studies were carried out to investigate the structural behavior of precast foamed concrete sandwich panels (PFCSP) of total number (6) as one-way action slab tested under lateral load. The details of the test setup and procedures were illustrated. The results obtained from the experimental tests were discussed which include the observation of cracking patterns and influence of aspect ratio (L/b). Analytical study of finite element analysis was implemented and degree of composite action of the test panels was also examined in both experimental and analytical studies. Result shows that crack patterns appeared in only one-direction, similar to reports on solid slabs, particularly when both concrete wythes act in a composite manner. Foamed concrete was briefly reviewed and experimental results were compared with the finite element analyses data which gives a reasonable degree of accuracy. Therefore, based on the results obtained, PFCSP slab can be used as an alternative to conventional flooring system.
Abstract: Anthropogenic sources of zinc (Zn), including industrial emissions and effluents, Zn–rich fertilizer materials and pesticides containing Zn, can contribute to increasing the concentration of soluble Zn at levels toxic to plants in acid sandy soils. The application of municipal sewage sludge or biosolids (MBS) which contain metal immobilizing agents on coarse-textured soils could improve the metal sorption capacity of the low-CEC soils. The purpose of this experiment was to evaluate the sorption of Zn in surface samples (0-15 cm) of six Quebec (Canada) soils amended with MBS (pH 6.9) from Val d’Or (Quebec, Canada). Soil samples amended with increasing amounts (0 to 20%) of MBS were equilibrated with various amounts of Zn as ZnCl2 in 0.01 M CaCl2 for 48 hours at room temperature. Sorbed Zn was calculated from the difference between the initial and final Zn concentration in solution. Zn sorption data conformed to the linear form of Freundlich equation. The amount of sorbed Zn increased considerably with increasing MBS rate. Analysis of variance revealed a highly significant effect (p ≤ 0.001) of soil texture and MBS rate on the amount of sorbed Zn. The average values of the Zn-sorption capacity of MBS-amended coarse-textured soils were lower than those of MBS-amended fine textured soils. The two sandy soils (86-99% sand) amended with MBS retained 2- to 5-fold Zn than those without MBS (control). Significant Pearson correlation coefficients between the Zn sorption isotherm parameter, i.e. the Freundlich sorption isotherm (KF), and commonly measured physical and chemical entities were obtained. Among all the soil properties measured, soil pH gave the best significant correlation coefficients (p ≤ 0.001) for soils receiving 0, 5 and 10% MBS. Furthermore, KF values were positively correlated with soil clay content, exchangeable basic cations (Ca, Mg or K), CEC and clay content to CEC ratio. From these results, it can be concluded that (i) municipal biosolids provide sorption sites that have a strong affinity for Zn, (ii) both soil texture, especially clay content, and soil pH are the main factors controlling anthropogenic Zn sorption in the municipal biosolids-amended soils, and (iii) the effect of municipal biosolids on Zn sorption will be more pronounced for a sandy soil than for a clay soil.
Abstract: In this paper, shear behavior of reconstituted clay reinforced with varying diameter of sand compaction piles with area replacement-ratio (as) of 6.25, 10.24, 16, 20.25 and 64% in 100mm diameter and 200mm long clay specimens is modeled using consolidated drained and undrained triaxial tests under different confining pressures ranging from 50kPa to 575kPa. The test results show that the stress-strain behavior of the clay was highly influenced by the presence of SCP. The insertion of SCPs into soft clay has shown to have a positive effect on the load carrying capacity of the clay, resulting in a composite soil mass that has greater shear strength and improved stiffness compared to the unreinforced clay due to increased reinforcement area ratio. In addition, SCP also acts as vertical drain in the clay thus accelerating the dissipation of excess pore water pressures that are generated during loading by shortening the drainage path and activating radial drainage, thereby reducing post-construction settlement. Thus, sand compaction piles currently stand as one of the most viable and practical techniques for improving the mechanical properties of soft clays.
Abstract: In the process of recovering oil in weak sandstone formations, the strength of sandstones around the wellbore is weakened due to the increase of effective stress/load from the completion activities around the cavity. The weakened and de-bonded sandstone may be eroded away by the produced fluid, which is termed sand production. It is one of the major trending subjects in the petroleum industry because of its significant negative impacts, as well as some observed positive impacts. For efficient sand management therefore, there has been need for a reliable study tool to understand the mechanism of sanding. One method of studying sand production is the use of the widely recognized Discrete Element Method (DEM), Particle Flow Code (PFC3D) which represents sands as granular individual elements bonded together at contact points. However, there is limited knowledge of the particle-scale behavior of the weak sandstone, and the parameters that affect sanding. This paper aims to investigate the reliability of using PFC3D and a simple Darcy flow in understanding the sand production behavior of a weak sandstone. An isotropic tri-axial test on a weak oil sandstone sample was first simulated at a confining stress of 1MPa to calibrate and validate the parallel bond models of PFC3D using a 10m height and 10m diameter solid cylindrical model. The effect of the confining stress on the number of bonds failure was studied using this cylindrical model. With the calibrated data and sample material properties obtained from the tri-axial test, simulations without and with fluid flow were carried out to check on the effect of Darcy flow on bonds failure using the same model geometry. The fluid flow network comprised of every four particles connected with tetrahedral flow pipes with a central pore or flow domain. Parametric studies included the effects of confining stress, and fluid pressure; as well as validating flow rate – permeability relationship to verify Darcy’s fluid flow law. The effect of model size scaling on sanding was also investigated using 4m height, 2m diameter model. The parallel bond model successfully calibrated the sample’s strength of 4.4MPa, showing a sharp peak strength before strain-softening, similar to the behavior of real cemented sandstones. There seems to be an exponential increasing relationship for the bigger model, but a curvilinear shape for the smaller model. The presence of the Darcy flow induced tensile forces and increased the number of broken bonds. For the parametric studies, flow rate has a linear relationship with permeability at constant pressure head. The higher the fluid flow pressure, the higher the number of broken bonds/sanding. The DEM PFC3D is a promising tool to studying the micromechanical behavior of cemented sandstones.
Abstract: This paper details the progress made in the development of the different state-of-the-art aerodynamic tools for the analysis of vertical axis wind turbines including the flow simulation around the blade, viscous flow, stochastic wind, and dynamic stall effects. The paper highlights the capabilities of the developed wind turbine aerodynamic codes over the last thirty years which are currently being used in North America and Europe by Sandia Laboratories, FloWind, IMST Marseilles, and Hydro-Quebec among others. The aerodynamic codes developed at Ecole Polytechnique de Montreal, Canada, represent valuable tools for simulating the flow around wind turbines including secondary effects. Comparison of theoretical results with experimental data have shown good agreement. The strength of the aerodynamic codes based on Double-Multiple Stream tube model (DMS) lies in its simplicity, accuracy, and ability to analyze secondary effects that interfere with wind turbine aerodynamic calculations.
Abstract: The Metropolitan Region of Sao Paulo (MRSP) has suffered from serious water scarcity. Consequently, the most convenient solution has been building wells to extract groundwater from local aquifers. However, it requires constant vigilance to prevent over extraction and future events that can pose serious threat to the population, such as subsidence. Radar imaging techniques (InSAR) have allowed continuous investigation of such phenomena. The analysis of data in the present study consists of 23 SAR images dated from October 2007 to March 2011, obtained by the ALOS-1 spacecraft. Data processing was made with the software GMTSAR, by using the InSAR technique to create pairs of interferograms with ground displacement during different time spans. First results show a correlation between the location of 102 wells registered in 2009 and signals of ground displacement equal or lower than -90 millimeters (mm) in the region. The longest time span interferogram obtained dates from October 2007 to March 2010. As a result, from that interferogram, it was possible to detect the average velocity of displacement in millimeters per year (mm/y), and which areas strong signals have persisted in the MRSP. Four specific areas with signals of subsidence of 28 mm/y to 40 mm/y were chosen to investigate the phenomenon: Guarulhos (Sao Paulo International Airport), the Greater Sao Paulo, Itaquera and Sao Caetano do Sul. The coverage area of the signals was between 0.6 km and 1.65 km of length. All areas are located above a sedimentary type of aquifer. Itaquera and Sao Caetano do Sul showed signals varying from 28 mm/y to 32 mm/y. On the other hand, the places most likely to be suffering from stronger subsidence are the ones in the Greater Sao Paulo and Guarulhos, right beside the International Airport of Sao Paulo. The rate of displacement observed in both regions goes from 35 mm/y to 40 mm/y. Previous investigations of the water use at the International Airport highlight the risks of excessive water extraction that was being done through 9 deep wells. Therefore, it is affirmed that subsidence events are likely to occur and to cause serious damage in the area. This study could show a situation that has not been explored with proper importance in the city, given its social and economic consequences. Since the data were only available until 2011, the question that remains is if the situation still persists. It could be reaffirmed, however, a scenario of risk at the International Airport of Sao Paulo that needs further investigation.
Abstract: Not all proteins have the same nutritional value, since
protein quality strongly depends on its amino acid composition and
digestibility. The meat of game animals could be a high protein
source because of its well-balanced essential amino acids
composition. Investigations about biochemical composition of game
meat such as wild boar (Sus scrofa scrofa), roe deer (Capreolus
capreolus) and beaver (Castor fiber) are not very much. Therefore,
the aim of the investigation was evaluate protein composition of
game meat hunted in Latvia. The biochemical analysis, evaluation of
connective tissue and essential amino acids in meat samples were
done, the amino acids score were calculate. Results of analysis
showed that protein content 20.88-22.05% of all types of meat
samples is not different statistically. The content of connective tissue
from 1.3% in roe deer till 1.5% in beaver meat allowed classified
game animal as high quality meat. The sum of essential amino acids
in game meat samples were determined 7.05–8.26g100g-1. Roe deer
meat has highest protein content and lowest content of connective
tissues among game meat hunted in Latvia. Concluded that amino
acid score for limiting amino acids phenylalanine and tyrosine is high
and shows high biological value of game meat.
Abstract: Experiments were performed to investigate the effects of roughness on the reattachment and redevelopment regions over a 12 mm forward facing step (FFS) in an open channel flow. The experiments were performed over an upstream smooth wall and a smooth FFS, an upstream wall coated with sandpaper 36 grit and a smooth FFS and an upstream rough wall produced from sandpaper 36 grit and a FFS coated with sandpaper 36 grit. To investigate only the wall roughness effects, Reynolds number, Froude number, aspect ratio and blockage ratio were kept constant. Upstream profiles showed reduced streamwise mean velocities close to the rough wall compared to the smooth wall, but the turbulence level was increased by upstream wall roughness. The reattachment length for the smooth-smooth wall experiment was 1.78h; however, when it is replaced with rough-smooth wall the reattachment length decreased to 1.53h. It was observed that the upstream roughness increased the physical size of contours of maximum turbulence level; however, the downstream roughness decreased both the size and magnitude of contours in the vicinity of the leading edge of the step. Quadrant analysis was performed to investigate the dominant Reynolds shear stress contribution in the recirculation region. The Reynolds shear stress and turbulent kinetic energy profiles after the reattachment showed slower recovery compared to the streamwise mean velocity, however all the profiles fairly collapse on their corresponding upstream profiles at x/h = 60. It was concluded that to obtain a complete collapse several more streamwise distances would be required.
Abstract: The effect of upstream surface roughness over a
smooth forward facing step in an open channel was investigated
using a particle image velocimetry technique. Three different
upstream surface topographies consisting of hydraulically smooth
wall, sandpaper 36 grit and sand grains were examined. Besides the
wall roughness conditions, all other upstream flow characteristics
were kept constant. It was also observed that upstream roughness
decreased the approach velocity by 2% and 10% but increased the
turbulence intensity by 14% and 35% at the wall-normal distance
corresponding to the top plane of the step compared to smooth
upstream. The results showed that roughness decreased the
reattachment lengths by 14% and 30% compared to smooth upstream.
Although the magnitudes of maximum positive and negative
Reynolds shear stress in separated and reattached region were 0.02Ue
for all the cases, the physical size of both the maximum and
minimum contour levels were decreased by increasing upstream
roughness.
Abstract: Centrifugal-casting machine is used in manufacturing
special machine components like multi-layer journal bearing used in
all internal combustion engine, steam, gas turbine and air craft turboengine
where isotropic properties and high precisions are desired.
Moreover, this machine can be used in manufacturing thin wall hightech
machine components like cylinder liners and piston rings of IC
engine and other machine parts like sleeves, and bushes. Heavy-duty
machine component like railway wheel can also be prepared by
centrifugal casting. A lot of technological developments are required
in casting process for production of good casted machine body and
machine parts. Usually defects like blowholes, surface roughness,
chilled surface etc. are found in sand casted machine parts. But these
can be removed by centrifugal casting machine using rotating
metallic die. Moreover, die rotation, its temperature control, and good
pouring practice can contribute to the quality of casting because of
the fact that the soundness of a casting in large part depends upon
how the metal enters into the mold or dies and solidifies. Poor
pouring practice leads to variety of casting defects such as
temperature loss, low quality casting, excessive turbulence, over
pouring etc. Besides these, handling of molten metal is very
unsecured and dangerous for the workers. In order to get rid of all
these problems, the need of an automatic pouring device arises. In
this research work, a robot assisted pouring device and a centrifugal
casting machine are designed, developed constructed and tested
experimentally which are found to work satisfactorily. The robot
assisted pouring device is further modified and developed for using it
in actual metal casting process. Lot of settings and tests are required
to control the system and ultimately it can be used in automation of
centrifugal casting machine to produce high-tech machine parts with
desired precision.
Abstract: This paper explored the challenges faced by the
management of a Ghanaian state enterprise in managing conflicts and
disturbances associated with its attempt to implement new work
practices to enhance its capability to operate as a commercial entity.
The purpose was to understand the extent to which organizational
involvement, consistency and adaptability influence employees’
consumption of new work practices in transforming the
organization’s organizational activity system. Using selfadministered
questionnaires, data were collected from one hundred
and eighty (180) employees and analyzed using both descriptive and
inferential statistics. The results showed that constraints in
organizational involvement and adaptability prevented the positive
consumption of new work practices by employees in the
organization. It is also found that the organization’s employees failed
to consume the new practices being implemented, because they
perceived the process as non-involving, and as such, did not
encourage the development of employee capability, empowerment,
and teamwork. The study concluded that the failure of the
organization’s management to create opportunities for organizational
learning constrained its ability to get employees consume the new
work practices, which situation could have facilitated the
organization’s capabilities of operating as a commercial entity.
Abstract: In this paper, we introduce a flexible box erecting
machine (BEM) that swiftly and automatically transforms cardboard
into a three dimensional box. Recently, the parcel service and
home-shopping industries have grown rapidly, and there is an
increasing need for various box types to ship various products.
However, workers cannot fold thousands of boxes manually in a day.
As such, automatic BEMs are garnering greater attention. This study
takes equipment operation into consideration as well as mechanical
improvements in order to design a BEM that is able to outperform its
conventional counterparts. We analyzed six dispatching rules – First In
First Out (FIFO), Shortest Processing Time (SPT), Earliest Due Date
(EDD), Setup Avoidance, EDD + SPT, and EDD + Setup Avoidance –
to determine which one was most suitable for BEM operation.
Consequently, SPT and Setup Avoidance were found to be the most
critical rules, followed by EDD + Setup Avoidance, EDD + SPT,
EDD, and FIFO. This hierarchy was valid for both our conventional
BEM and our new flexible BEM from the viewpoint of processing
time. We believe that this research can contribute to flexible BEM
management, which has the potential to increase productivity and
convenience.
Abstract: This paper presents numerical analysis in terms of
buckling resistance of GFRP sandwich infill panels system under the
influence of increased temperature on the foam core. Failure mode
under in-plane compression is studied by means of numerical analysis
with ABAQUS platform. Parameters considered in this study are
contact length and both the type of foam for core and the variation of
its module elastic under the thermal influence. Increment of
temperature is considered in static cases and only applied to core.
Indeed, it is proven that the effect of temperature alters the mechanical
properties of the entire panel system. Moreover, the rises of
temperature result in a decrease in strength of the panel. This is due to
the polymeric nature of this material. Additionally, the contact length
also displays the effect on performance of infill panel. Their
significance factors are based on type of polymer for core. Therefore,
by comparing difference type of core material, the variation can be
reducing.
Abstract: Inspired by the Formula-1 competition, IMechE
(Institute of Mechanical Engineers) and Formula SAE (Society of
Mechanical Engineers) organize annual competitions for University
and College students worldwide to compete with a single-seat racecar
they have designed and built. Design of the chassis or the frame is a
key component of the competition because the weight and stiffness
properties are directly related with the performance of the car and the
safety of the driver. In addition, a reduced weight of the chassis has
direct influence on the design of other components in the car. Among
others, it improves the power to weight ratio and the aerodynamic
performance. As the power output of the engine or the battery
installed in the car is limited to 80 kW, increasing the power to
weight ratio demands reduction of the weight of the chassis, which
represents the major part of the weight of the car. In order to reduce
the weight of the car, ION Racing team from University of
Stavanger, Norway, opted for a monocoque design. To ensure
fulfilment of the competition requirements of the chassis, the
monocoque design should provide sufficient torsional stiffness and
absorb the impact energy in case of possible collision. The study reported in this article is based on the requirements for
Formula Student competition. As part of this study, diverse
mechanical tests were conducted to determine the mechanical
properties and performances of the monocoque design. Upon a
comprehensive theoretical study of the mechanical properties of
sandwich composite materials and the requirements of monocoque
design in the competition rules, diverse tests were conducted
including 3-point bending test, perimeter shear test and test for
absorbed energy. The test panels were homemade and prepared with
equivalent size of the side impact zone of the monocoque, i.e. 275
mm x 500 mm, so that the obtained results from the tests can be
representative. Different layups of the test panels with identical core
material and the same number of layers of carbon fibre were tested
and compared. Influence of the core material thickness was also
studied. Furthermore, analytical calculations and numerical analysis
were conducted to check compliance to the stated rules for Structural
Equivalency with steel grade SAE/AISI 1010. The test results were
also compared with calculated results with respect to bending and
torsional stiffness, energy absorption, buckling, etc. The obtained results demonstrate that the material composition
and strength of the composite material selected for the monocoque
design has equivalent structural properties as a welded frame and thus
comply with the competition requirements. The developed analytical
calculation algorithms and relations will be useful for future
monocoque designs with different lay-ups and compositions.
Abstract: The main purpose of this study is to assess the
sediment quality and potential ecological risk in marine sediments in
Gymea Bay located in south Sydney, Australia. A total of 32 surface
sediment samples were collected from the bay. Current track
trajectories and velocities have also been measured in the bay. The
resultant trace elements were compared with the adverse biological
effect values Effect Range Low (ERL) and Effect Range Median
(ERM) classifications. The results indicate that the average values of
chromium, arsenic, copper, zinc, and lead in surface sediments all
reveal low pollution levels and are below ERL and ERM values. The
highest concentrations of trace elements were found close to
discharge points and in the inner bay, and were linked with high
percentages of clay minerals, pyrite and organic matter, which can
play a significant role in trapping and accumulating these elements.
The lowest concentrations of trace elements were found to be on the
shoreline of the bay, which contained high percentages of sand
fractions. It is postulated that the fine particles and trace elements are
disturbed by currents and tides, then transported and deposited in
deeper areas. The current track velocities recorded in Gymea Bay had
the capability to transport fine particles and trace element pollution
within the bay. As a result, hydrodynamic measurements were able to
provide useful information and to help explain the distribution of
sedimentary particles and geochemical properties. This may lead to
knowledge transfer to other bay systems, including those in remote
areas. These activities can be conducted at a low cost, and are
therefore also transferrable to developing countries. The advent of
portable instruments to measure trace elements in the field has also
contributed to the development of these lower cost and easily applied
methodologies available for use in remote locations and low-cost
economies.
Abstract: We regard forecasting of energy consumption by
private production areas of a large industrial facility as well as by the
facility itself. As for production areas, the forecast is made based on
empirical dependencies of the specific energy consumption and the
production output. As for the facility itself, implementation of the
task to minimize the energy consumption forecasting error is based
on adjustment of the facility’s actual energy consumption values
evaluated with the metering device and the total design energy
consumption of separate production areas of the facility. The
suggested procedure of optimal energy consumption was tested based
on the actual data of core product output and energy consumption by
a group of workshops and power plants of the large iron and steel
facility. Test results show that implementation of this procedure gives
the mean accuracy of energy consumption forecasting for winter
2014 of 0.11% for the group of workshops and 0.137% for the power
plants.
Abstract: The photovoltaic and the semiconductor industries are
in growth and it is necessary to supply a large amount of silicon to
maintain this growth. Since silicon is still the best material for the
manufacturing of solar cells and semiconductor components so the
pure silicon like solar grade and semiconductor grade materials are
demanded. There are two main routes for silicon production:
metallurgical and chemical. In this article, we reviewed the
electrotecnological installations and systems for semiconductor
manufacturing. The main task is to design the installation which can
produce SOG Silicon from river sand by one work unit.
Abstract: The post-rain puddles problem that occurs in the first
yard of Prambanan Temple are often disturbing visitor activity. A
poodle layer and a drainage system had ever built to avoid such a
problem, but puddles still did not stop appearing after rain.
Permeability parameter needs to be determined by using a simpler
procedure to find exact method of solution. The instrument modelling
was proposed according to the development of field permeability
testing instrument. This experiment used a proposed Constant
Discharge method. Constant Discharge method used a tube poured
with constant water flow from unsaturated until saturated soil
condition. Volumetric water content (θ) were monitored by soil
moisture measurement device. The results were correlations between
k and θ which were drawn by numerical approach from Van
Genutchen model. Parameters θr optimum value obtained from the
test was at very dry soil. Coefficient of permeability with a density of
19.8 kN/m3 for unsaturated conditions was in range of 3 x 10-6
cm/sec (Sr=68%) until 9.98 x 10-4 cm/sec (Sr=82%). The equipment
and testing procedure developed in this research was quite effective,
simple and easy to be implemented on determining field soil
permeability coefficient value of sandy soil. Using constant discharge
method in proposed permeability test, value of permeability
coefficient under unsaturated condition can be obtained without
establish soil water characteristic curve.
Abstract: This paper describes the development of a DNA-based
nanobiosensor to detect the dengue virus in mosquito using
electrically active magnetic (EAM) nanoparticles as concentrator and
electrochemical transducer. The biosensor detection encompasses
two sets of oligonucleotide probes that are specific to the dengue
virus: the detector probe labeled with the EAM nanoparticles and the
biotinylated capture probe. The DNA targets are double hybridized to
the detector and the capture probes and concentrated from
nonspecific DNA fragments by applying a magnetic field.
Subsequently, the DNA sandwiched targets (EAM-detector probe–
DNA target–capture probe-biotin) are captured on streptavidin
modified screen printed carbon electrodes through the biotinylated
capture probes. Detection is achieved electrochemically by measuring
the oxidation–reduction signal of the EAM nanoparticles. Results
indicate that the biosensor is able to detect the redox signal of the
EAM nanoparticles at dengue DNA concentrations as low as 10
ng/μl.
Abstract: The increase of technogenic and natural accidents,
accompanied by air pollution, for example, by combustion products,
leads to the necessity of respiratory protection. This work is devoted to the development of a calorimetric method
and a device which allows investigating quickly the kinetics of
carbon dioxide sorption by chemisorbents on the base of potassium
superoxide in order to assess the protective properties of respiratory
protective closed circuit apparatus. The features of the traditional approach for determining the
sorption properties in a thin layer of chemisorbent are described, as
well as methods and devices, which can be used for the sorption
kinetics study. The authors developed an approach (as opposed to the traditional
approach) based on the power measurement of internal heat sources
in the chemisorbent layer. The emergence of the heat sources is a
result of exothermic reaction of carbon dioxide sorption. This
approach eliminates the necessity of chemical analysis of samples
and can significantly reduce the time and material expenses during
chemisorbents testing. Error of determining the volume fraction of adsorbed carbon
dioxide by the developed method does not exceed 12%. Taking into
account the efficiency of the method, we consider that it is a good
alternative to traditional methods of chemical analysis under the
assessment of the protection sorbents quality.