Abstract: Noise level has critical effects on the diagnostic
performance of signal-averaged electrocardiogram (SAECG), because
the true starting and end points of QRS complex would be masked by
the residual noise and sensitive to the noise level. Several studies and
commercial machines have used a fixed number of heart beats
(typically between 200 to 600 beats) or set a predefined noise level
(typically between 0.3 to 1.0 μV) in each X, Y and Z lead to perform
SAECG analysis. However different criteria or methods used to
perform SAECG would cause the discrepancies of the noise levels
among study subjects. According to the recommendations of 1991
ESC, AHA and ACC Task Force Consensus Document for the use of
SAECG, the determinations of onset and offset are related closely to
the mean and standard deviation of noise sample. Hence this study
would try to perform SAECG using consistent root-mean-square
(RMS) noise levels among study subjects and analyze the noise level
effects on SAECG. This study would also evaluate the differences
between normal subjects and chronic renal failure (CRF) patients in
the time-domain SAECG parameters.
The study subjects were composed of 50 normal Taiwanese and 20
CRF patients. During the signal-averaged processing, different RMS
noise levels were adjusted to evaluate their effects on three time
domain parameters (1) filtered total QRS duration (fQRSD), (2) RMS
voltage of the last QRS 40 ms (RMS40), and (3) duration of the low
amplitude signals below 40 μV (LAS40). The study results
demonstrated that the reduction of RMS noise level can increase
fQRSD and LAS40 and decrease the RMS40, and can further increase
the differences of fQRSD and RMS40 between normal subjects and
CRF patients. The SAECG may also become abnormal due to the
reduction of RMS noise level. In conclusion, it is essential to establish
diagnostic criteria of SAECG using consistent RMS noise levels for
the reduction of the noise level effects.
Abstract: Induction machine models used for steady-state and
transient analysis require machine parameters that are usually
considered design parameters or data. The knowledge of induction
machine parameters is very important for Indirect Field Oriented
Control (IFOC). A mismatched set of parameters will degrade the
response of speed and torque control. This paper presents an
improvement approach on rotor time constant adaptation in IFOC for
Induction Machines (IM). Our approach tends to improve the
estimation accuracy of the fundamental model for flux estimation.
Based on the reduced order of the IM model, the rotor fluxes and
rotor time constant are estimated using only the stator currents and
voltages. This reduced order model offers many advantages for real
time identification parameters of the IM.
Abstract: The influence of extrusion parameters on surface
quality and properties of AA6061+x% vol. SiC (x = 0; 2,5; 5; 7,5;10)
composites was discussed in this paper. The averages size of
AA6061 and SiC particles were 10.6 μm and 0.42 μm, respectively.
Two series of composites (I - compacts were preheated at extrusion
temperature through 0.5 h and cooled by water directly after process;
II - compacts were preheated through 3 hours and were not cooled)
were consolidated via powder metallurgy processing and extruded by
KoBo method. High values of density for both series of composites
were achieved. Better surface quality was observed for II series of
composites. Moreover, for these composites lower (compared to I
series) but more uniform strength properties over the cross-section of
the bar were noticed. Microstructure and Young-s modulus
investigations were made.
Abstract: Reverse engineering of full-genomic interaction networks based on compendia of expression data has been successfully applied for a number of model organisms. This study adapts these approaches for an important non-model organism: The major human fungal pathogen Candida albicans. During the infection process, the pathogen can adapt to a wide range of environmental niches and reversibly changes its growth form. Given the importance of these processes, it is important to know how they are regulated. This study presents a reverse engineering strategy able to infer fullgenomic interaction networks for C. albicans based on a linear regression, utilizing the sparseness criterion (LASSO). To overcome the limited amount of expression data and small number of known interactions, we utilize different prior-knowledge sources guiding the network inference to a knowledge driven solution. Since, no database of known interactions for C. albicans exists, we use a textmining system which utilizes full-text research papers to identify known regulatory interactions. By comparing with these known regulatory interactions, we find an optimal value for global modelling parameters weighting the influence of the sparseness criterion and the prior-knowledge. Furthermore, we show that soft integration of prior-knowledge additionally improves the performance. Finally, we compare the performance of our approach to state of the art network inference approaches.
Abstract: Polyurethane foams (PUF) were formed by a chemical
reaction of polyol and isocyanate. The polyol was manufactured by
ring-opening hydrolysis of epoxidized soybean oil in the presence of
phosphoric acid under varying experimental conditions. Other
factors in the foam formulation such as water content and surfactant
were kept constant. The effect of the amount of solvents, phosphoric
acid, and their derivates in the foam formulation on the properties of
polyurethane foams were studied. The properties of the material were
measured via a number of parameters, which are water content of
prepared polyol, polymer density and cellular structures.
Abstract: While financial institutions have faced difficulties
over the years for a multitude of reasons, the major cause of serious
banking problems continues to be directly related to lax credit
standards for borrowers and counterparties, poor portfolio risk
management, or a lack of attention to changes in economic or other
circumstances that can lead to a deterioration in the credit standing of
a bank's counterparties. Credit risk is most simply defined as the
potential that a bank borrower or counterparty will fail to meet its
obligations in accordance with agreed terms. The goal of credit risk
management is to maximize a bank's risk-adjusted rate of return by
maintaining credit risk exposure within acceptable parameters. Banks
need to manage the credit risk inherent in the entire portfolio as well
as the risk in individual credits or transactions. Banks should also
consider the relationships between credit risk and other risks. The
effective management of credit risk is a critical component of a
comprehensive approach to risk management and essential to the
long-term success of any banking organization. In this research we
also study the relationship between credit risk indices and borrower-s
timely payback in Karafarin bank.
Abstract: Female breast cancer is the second in frequency after cervical cancer. Surgery is the most common treatment for breast cancer, followed by chemotherapy as a treatment of choice. Although effective, it causes serious side effects. Controlled-release drug delivery is an alternative method to improve the efficacy and safety of the treatment. It can release the dosage of drug between the minimum effect concentration (MEC) and minimum toxic concentration (MTC) within tumor tissue and reduce the damage of normal tissue and the side effect. Because an in vivo experiment of this system can be time-consuming and labor-intensive, a mathematical model is desired to study the effects of important parameters before the experiments are performed. Here, we describe a 3D mathematical model to predict the release of doxorubicin from pluronic gel to treat human breast cancer. This model can, ultimately, be used to effectively design the in vivo experiments.
Abstract: We derive simple sets of equations to describe the microwave response of a thin film of magnetized hydrogen plasma in the presence of carbon nanotubes, which were grown by ironcatalyzed high-pressure disproportionation (HiPco). By considering the interference effects due to multiple reflections between thin plasma film interfaces, we present the effects of the continuously changing external magnetic field and plasma parameters on the reflected power, absorbed power, and transmitted power in the system. The simulation results show that the interference effects play an important role in the reflectance, transmittance and absorptance of microwave radiation at the magnetized plasma slab. As a consequence, the interference effects lead to a sinusoidal variation of the reflected intensity and can greatly reduce the amount of reflection power, but the absorption power increases.
Abstract: In a liberalized electricity market, it is not surprising
that different customers require different power quality (PQ) levels at
different price. Power quality related to several power disturbances is
described by many parameters, so how to define a comprehensive
hierarchy evaluation system of power quality (PQCHES) has become
a concerned issue. In this paper, based on four electromagnetic
compatibility (EMC) levels, the numerical range of each power
disturbance is divided into five grades (Grade I –Grade V), and the
“barrel principle" of power quality is used for the assessment of
overall PQ performance with only one grade indicator. A case study
based on actual monitored data of PQ shows that the site PQ grade
indicates the electromagnetic environment level and also expresses the
characteristics of loads served by the site.
The shortest plank principle of PQ barrel is an incentive
mechanism, which can combine with the rewards/penalty mechanism
(RPM) of consumed energy “on quality demand", to stimulate utilities
to improve the overall PQ level and also stimulate end-user more
“smart" under the infrastructure of future SmartGrid..
Abstract: Anaerobic treatment has many advantages over other
biological method particularly when used to treat complex
wastewater such as petroleum refinery wastewater. In this study two
Up-flow Anaerobic Sludge Blanket (UASB) reactors were operated
in parallel to treat six volumetric organic loads (0.58, 1.21, 0.89,
2.34, 1.47 and 4.14 kg COD/m3·d) to evaluate the chemical oxygen
demand (COD) removal efficiency. The reactors were continuously
adapting to the changing of operation condition with increase in the
removal efficiency or slight decrease until the last load which was
more than two times the load, at which the reactor stressed and the
removal efficiency decreased to 75% with effluent concentration of
1746 mg COD/L. Other parameters were also monitored such as pH,
alkalinity, volatile fatty acid and gas production rate. The UASB
reactor was suitable to treat petroleum refinery wastewater and the
highest COD removal rate was 83% at 1215 kg/m3·d with COD
concentration about 356 mg/L in the effluent.
Abstract: Three dimensional analysis of thermal model in laser
full penetration welding, Nd:YAG, by transparent mode DP600 alloy
steel 1.25mm of thickness and gap of 0.1mm. Three models studied
the influence of thermal dependent temperature properties, thermal
independent temperature and the effect of peak value of specific heat
at phase transformation temperature, AC1, on the transient
temperature. Another seven models studied the influence of
discretization, meshes on the temperature distribution in weld plate.
It is shown that for the effects of thermal properties, the errors less
4% of maximum temperature in FZ and HAZ have identified. The
minimum value of discretization are at least one third increment per
radius for temporal discretization and the spatial discretization
requires two elements per radius and four elements through thickness
of the assembled plate, which therefore represent the minimum
requirements of modeling for the laser welding in order to get
minimum errors less than 5% compared to the fine mesh.
Abstract: The technique of inducing micro ecosystem
restoration is one of aquatic ecology engineering methods used to
retrieve the polluted water. Batch scale study, pilot plant study, and
field study were carried out to observe the eutrophication using the
Inducing Ecology Restorative Symbiosis Agent (IERSA) consisting
mainly degraded products by using lactobacillus, saccharomycete,
and phycomycete. The results obtained from the experiments of the
batch scale and pilot plant study allowed us to development the
parameters for the field study. A pond, 5 m to the outlet of a lake,
with an area of 500 m2 and depth of 0.6-1.2 m containing about 500
tons of water was selected as a model. After the treatment with 10
mg IERSA/L water twice a week for 70 days, the micro restoration
mechanisms consisted of three stages (i.e., restoration, impact
maintenance, and ecology recovery experiment after impact). The
COD, TN, TKN, and chlorophyll a were reduced significantly in the
first week. Although the unexpected heavy rain and contaminate
from sewage system might slow the ecology restoration. However,
the self-cleaning function continued and the chlorophyll a reduced
for 50% in one month. In the 4th week, amoeba, paramecium, rotifer,
and red wriggle worm reappeared, and the number of fish flies
appeared up to1000 fish fries/m3. Those results proved that inducing
restorative mechanism can be applied to improve the eutrophication
and to control the growth of algae in the lakes by gaining the selfcleaning
through inducing and competition of microbes. The
situation for growth of fishes also can reach an excellent result due to
the improvement of water quality.
Abstract: In this paper a novel scheme for watermarking digital
audio during its compression to MPEG-1 Layer III format is
proposed. For this purpose we slightly modify some of the selected
MDCT coefficients, which are used during MPEG audio
compression procedure. Due to the possibility of modifying different
MDCT coefficients, there will be different choices for embedding the
watermark into audio data, considering robustness and transparency
factors. Our proposed method uses a genetic algorithm to select the
best coefficients to embed the watermark. This genetic selection is
done according to the parameters that are extracted from the
perceptual content of the audio to optimize the robustness and
transparency of the watermark. On the other hand the watermark
security is increased due to the random nature of the genetic
selection. The information of the selected MDCT coefficients that
carry the watermark bits, are saves in a database for future extraction
of the watermark. The proposed method is suitable for online MP3
stores to pursue illegal copies of musical artworks. Experimental
results show that the detection ratio of the watermarks at the bitrate
of 128kbps remains above 90% while the inaudibility of the
watermark is preserved.
Abstract: Speckle phenomena results from when coherent
radiation is reflected from a rough surface. Characterizing the speckle
strongly depends on the measurement condition and experimental
setup. In this paper we report the experimental results produced with
different parameters in the setup. We investigated the factors which
affects the speckle contrast, such as, F-number, gamma value and
exposure time of the camera, rather than geometric factors like the
distance between the projector lens to the screen, the viewing distance,
etc. The measurement results show that the speckle contrast decreases
by decreasing F-number, by increasing gamma value, and slightly
affects by exposure time of the camera and the gain value of the
camera.
Abstract: CONWIP (constant work-in-process) as a pull
production system have been widely studied by researchers to date.
The CONWIP pull production system is an alternative to pure push
and pure pull production systems. It lowers and controls inventory
levels which make the throughput better, reduces production lead
time, delivery reliability and utilization of work. In this article a
CONWIP pull production system was simulated. It was simulated
push and pull planning system. To compare these systems via a
production planning system (PPS) game were adjusted parameters of
each production planning system. The main target was to reduce the
total WIP and achieve throughput and delivery reliability to
minimum values. Data was recorded and evaluated. A future state
was made for real production of plastic components and the setup of
the two indicators with CONWIP pull production system which can
greatly help the company to be more competitive on the market.
Abstract: One of the main concerns about parallel mechanisms
is the presence of singular points within their workspaces. In singular
positions the mechanism gains or loses one or several degrees of
freedom. It is impossible to control the mechanism in singular
positions. Therefore, these positions have to be avoided. This is a
vital need especially in computer controlled machine tools designed
and manufactured on the basis of parallel mechanisms. This need has
to be taken into consideration when selecting design parameters. A
prerequisite to this is a thorough knowledge about the effect of
design parameters and constraints on singularity. In this paper,
quality condition index was introduced as a criterion for evaluating
singularities of different configurations of a hexapod mechanism
obtainable by different design parameters. It was illustrated that this
method can effectively be employed to obtain the optimum
configuration of hexapod mechanism with the aim of avoiding
singularity within the workspace. This method was then employed to
design the hexapod table of a CNC milling machine.
Abstract: The intent of this essay is to evaluate the effectiveness
of surge suppressor aimed at power supply used for automation
devices in power distribution system which is consist of MOV and
T type low-pass filter. Books, journal articles and e-sources related
to surge protection of power supply used for automation devices in
power distribution system were consulted, and the useful information
was organized, analyzed and developed into five parts: characteristics
of surge wave, protection against surge wave, impedance characteristics
of target, using Matlab to simulate circuit response after
5kV,1.2/50s surge wave and suggestions for surge protection. The
results indicate that various types of load situation have great impact
on the effectiveness of surge protective device. Therefore, type and
parameters of surge protective device need to be carefully selected,
and load matching is also vital to be concerned.
Abstract: In this paper we consider a nonlinear feedback control
called augmented automatic choosing control (AACC) using the
gradient optimization automatic choosing functions for nonlinear
systems. Constant terms which arise from sectionwise linearization
of a given nonlinear system are treated as coefficients of a stable
zero dynamics. Parameters included in the control are suboptimally
selected by expanding a stable region in the sense of Lyapunov
with the aid of the genetic algorithm. This approach is applied to
a field excitation control problem of power system to demonstrate
the splendidness of the AACC. Simulation results show that the new
controller can improve performance remarkably well.
Abstract: This study proposes a multi-response surface
optimization problem (MRSOP) for determining the proper choices
of a process parameter design (PPD) decision problem in a noisy
environment of a grease position process in an electronic industry.
The proposed models attempts to maximize dual process responses
on the mean of parts between failure on left and right processes. The
conventional modified simplex method and its hybridization of the
stochastic operator from the hunting search algorithm are applied to
determine the proper levels of controllable design parameters
affecting the quality performances. A numerical example
demonstrates the feasibility of applying the proposed model to the
PPD problem via two iterative methods. Its advantages are also
discussed. Numerical results demonstrate that the hybridization is
superior to the use of the conventional method. In this study, the
mean of parts between failure on left and right lines improve by
39.51%, approximately. All experimental data presented in this
research have been normalized to disguise actual performance
measures as raw data are considered to be confidential.
Abstract: Drilling is the most common machining operation and it forms the highest machining cost in many manufacturing activities including automotive engine production. The outcome of this operation depends upon many factors including utilization of proper cutting tool geometry, cutting tool material and the type of coating used to improve hardness and resistance to wear, and also cutting parameters. With the availability of a large array of tool geometries, materials and coatings, is has become a challenging task to select the best tool and cutting parameters that would result in the lowest machining cost or highest profit rate. This paper describes an algorithm developed to help achieve good performances in drilling operations by automatically determination of proper cutting tools and cutting parameters. It also helps determine machining sequences resulting in minimum tool changes that would eventually reduce machining time and cost where multiple tools are used.