Abstract: In this study, the Compressive strength of concretes
made with Ground Granulated Blast furnace Slag (GGBS),
Pulverised Fuel Ash (PFA), Rice Husk Ash (RHA) and Waste Glass
Powder (WGP) after they were exposed 7800C (exposure duration of
around 60 minutes) and then allowed to cool down gradually in the
furnace for about 280 minutes at water binder ratio of 0.50 was
investigated. GGBS, PFA, RHA and WGP were used to replace up to
20% Portland cement in the control concrete. Test for the
determination of workability, compressive strength and tensile
splitting strength of the concretes were carried out and the results
were compared with control concrete. The test results showed that the
compressive strength decreased by an average of around 30% after
the concretes were exposed to the heating and cooling scenario.
Abstract: Catalytic combustion of methane is imperative due to
stability of methane at low temperature. Methane (CH4), therefore,
remains unconverted in vehicle exhausts thereby causing greenhouse
gas GHG emission problem. In this study, heterogeneous catalysts of
palladium with bio-char (2 wt% Pd/Bc) and Al2O3 (2wt% Pd/ Al2O3)
supports were prepared by incipient wetness impregnation and then
subsequently tested for catalytic combustion of CH4. Support-porous
heterogeneous catalytic combustion (HCC) material were selected
based on factors such as surface area, porosity, thermal stability,
thermal conductivity, reactivity with reactants or products, chemical
stability, catalytic activity, and catalyst life. Sustainable and
renewable support-material of bio-mass char derived from palm shell
waste material was compared with those from the conventional
support-porous materials. Kinetic rate of reaction was determined for
combustion of methane on Palladium (Pd) based catalyst with Al2O3
support and bio-char (Bc). Material characterization was done using
TGA, SEM, and BET surface area. The performance test was
accomplished using tubular quartz reactor with gas mixture ratio of
3% methane and 97% air. The methane porous-HCC conversion was
carried out using online gas analyzer connected to the reactor that
performed porous-HCC. BET surface area for prepared 2 wt% Pd/Bc
is smaller than prepared 2wt% Pd/ Al2O3 due to its low porosity
between particles. The order of catalyst activity based on kinetic rate
on reaction of catalysts in low temperature was 2wt%
Pd/Bc>calcined 2wt% Pd/ Al2O3> 2wt% Pd/ Al2O3>calcined 2wt%
Pd/Bc. Hence agro waste material can successfully be utilized as an
inexpensive catalyst support material for enhanced CH4 catalytic
combustion.
Abstract: This study aimed to examine the management and
development of forest tourism Kamchanoad. Ban Dung, Udon Thani
sustainability. Data were collected by means of qualitative research
including in-depth interviews, semi- structured, and then the data
were summarized and discussed in accordance with the objectives.
And make a presentation in the form of lectures. The target
population for the study consisted of 16 people, including
representatives from government agencies, community leaders and
the community. The results showed that Guidelines for the
Management and Development of Forest Tourism Kamchanoad
include management of buildings and infrastructure such as roads,
water, electricity, toilets. Other developments are the establishment
of a service center that provides information and resources to
facilitate tourists.; nature trails and informative signage to educate
visitors on the path to the jungle Kamchanoad; forest activities for
tourists who are interested only in occasional educational activities
such as vegetation, etc.; disseminating information on various aspects
of tourism through various channels in both Thailand and English, as
well as a web site to encourage community involvement in the
planning and management of tourism together with the care and
preservation of natural resources and preserving the local cultural
tourist area of Kamchanoad.
Abstract: To determine the potential of a low cost Irish
engineered timber product to replace high cost solid timber for use in
bending active structures such as gridshells a single Irish engineered
timber product in the form of orientated strand board (OSB) was
selected. A comparative study of OSB and solid timber was carried
out to determine the optimum properties that make a material suitable
for use in gridshells. Three parameters were identified to be relevant
in the selection of a material for gridshells. These three parameters
are the strength to stiffness ratio, the flexural stiffness of
commercially available sections, and the variability of material and
section properties. It is shown that when comparing OSB against
solid timber, OSB is a more suitable material for use in gridshells that
are at the smaller end of the scale and that have tight radii of
curvature. Typically, for solid timber materials, stiffness is used as an
indicator for strength and engineered timber is no different. Thus, low
flexural stiffness would mean low flexural strength. However, when
it comes to bending active gridshells, OSB offers a significant
advantage. By the addition of multiple layers, an increased section
size is created, thus endowing the structure with higher stiffness and
higher strength from initial low stiffness and low strength materials
while still maintaining tight radii of curvature. This allows OSB to
compete with solid timber on large scale gridshells. Additionally, a
preliminary sustainability study using a set of sustainability indicators
was carried out to determine the relative sustainability of building a
large-scale gridshell in Ireland with a primary focus on economic
viability but a mention is also given to social and environmental
aspects. For this, the Savill garden gridshell in the UK was used as
the functional unit with the sustainability of the structural roof
skeleton constructed from UK larch solid timber being compared
with the same structure using Irish OSB. Albeit that the advantages of
using commercially available OSB in a bending active gridshell are
marginal and limited to specific gridshell applications, further study
into an optimised engineered timber product is merited.
Abstract: This paper proposes five level diode clamped Z source
Inverter. The existing PWM techniques used for ZSI are restricted for
two level. The two level Z Source Inverter have high harmonic
distortions which effects the performance of the grid connected PV
system. To improve the performance of the system the number of
voltage levels in the output waveform need to be increased. This
paper presents comparative analysis of a five level diode clamped Z
source Inverter with different carrier based Modified Pulse Width
Modulation techniques. The parameters considered for comparison
are output voltage, voltage gain, voltage stress across switch and total
harmonic distortion when powered by same DC supply. Analytical
results are verified using MATLAB.
Abstract: Most people today are aware that global climate
change is not just a scientific theory but also a fact with worldwide
consequences. Global climate change is due to rapid urbanization,
industrialization, high population growth and current vulnerability of
the climatic condition. Water is becoming scarce as a result of global
climate change. To mitigate the problem arising due to global climate
change and its drought effect, harvesting rainwater from green roofs,
an environmentally-friendly and versatile technology, is becoming
one of the best assessment criteria and gaining attention in Malaysia.
This paper addresses the sustainability of green roofs and examines
the quality of water harvested from green roofs in comparison to
rainwater. The factors that affect the quality of such water, taking
into account, for example, roofing materials, climatic conditions, the
frequency of rainfall frequency and the first flush. A green roof was
installed on the Humid Tropic Centre (HTC) is a place of the study
on monitoring program for urban Stormwater Management Manual
for Malaysia (MSMA), Eco-Hydrological Project in Kuala Lumpur,
and the rainwater was harvested and evaluated on the basis of four
parameters i.e., conductivity, dissolved oxygen (DO), pH and
temperature. These parameters were found to fall between Class I and
Class III of the Interim National Water Quality Standards (INWQS)
and the Water Quality Index (WQI). Some preliminary treatment
such as disinfection and filtration could likely to improve the value of
these parameters to class I. This review paper clearly indicates that
there is a need for more research to address other microbiological and
chemical quality parameters to ensure that the harvested water is
suitable for use potable water for domestic purposes. The change in
all physical, chemical and microbiological parameters with respect to
storage time will be a major focus of future studies in this field.
Abstract: Array-based gene expression analysis is a powerful
tool to profile expression of genes and to generate information on
therapeutic effects of new anti-cancer compounds. Anti-apoptotic
effect of thymoquinone was studied in MCF7 breast cancer cell line
using gene expression profiling with cDNA microarray. The purity
and yield of RNA samples were determined using RNeasyPlus Mini
kit. The Agilent RNA 6000 NanoLabChip kit evaluated the quantity
of the RNA samples. AffinityScript RT oligo-dT promoter primer
was used to generate cDNA strands. T7 RNA polymerase was used to
convert cDNA to cRNA. The cRNA samples and human universal
reference RNA were labelled with Cy-3-CTP and Cy-5-CTP,
respectively. Feature Extraction and GeneSpring softwares analysed
the data. The single experiment analysis revealed involvement of 64
pathways with up-regulated genes and 78 pathways with downregulated
genes. The MAPK and p38-MAPK pathways were
inhibited due to the up-regulation of PTPRR gene. The inhibition of
p38-MAPK suggested up-regulation of TGF-ß pathway. Inhibition of
p38-MAPK caused up-regulation of TP53 and down-regulation of
Bcl2 genes indicating involvement of intrinsic apoptotic pathway.
Down-regulation of CARD16 gene as an adaptor molecule regulated
CASP1 and suggested necrosis-like programmed cell death and
involvement of caspase in apoptosis. Furthermore, down-regulation
of GPCR, EGF-EGFR signalling pathways suggested reduction of
ER. Involvement of AhR pathway which control cytochrome P450
and glucuronidation pathways showed metabolism of Thymoquinone.
The findings showed differential expression of several genes in
apoptosis pathways with thymoquinone treatment in estrogen
receptor-positive breast cancer cells.
Abstract: We assessed the ecology of the organic and mineral soil
layers of laurel-leaved (BB-1) and Cryptomeria japonica (BB-2 and Pw)
forests in the Kasugayama Hill Primeval Forest (Nara, Japan). The soil
respiration rate was higher in the deeper horizons (F and H) of organic
layers than in those of mineral soil layers, suggesting organic layers
may be where active microbial metabolism occurs. Respiration rates in
the soil of BB-1, BB-2 and Pw forests were closely similar at 5 and 10°C.
However, the soil respiration rate increased in proportion to
temperatures of 15°C or above. We therefore consider the activity of
soil microorganisms to markedly decrease at temperatures below 10°C.
At a temperature of 15°C or above, the soil respiration rate in the BB-1
organic layers was higher than in those of the BB-2 and Pw organic
layers, due to differences in forest vegetation that appeared to
influence several salient soil properties, particularly pH and the carbon
(C) and nitrogen (N) content of the F and H horizons.
Abstract: Object-oriented modeling is spreading in current
simulation of physiological systems through the use of the individual
components of the model and its interconnections to define the
underlying dynamic equations. In this paper we describe the use of
both the SIMSCAPE and MODELICA simulation environments in
the object-oriented modeling of the closed loop cardiovascular
system. The performance of the controlled system was analyzed by
simulation in light of the existing hypothesis and validation tests
previously performed with physiological data. The described
approach represents a valuable tool in the teaching of physiology for
graduate medical students.
Abstract: Chemical vapor deposition (CVD) diamond coated
cutting tool has excellent cutting performance, it is the most ideal tool
for the processing of nonferrous metals and alloys, composites,
nonmetallic materials and other difficult-to-machine materials
efficiently and accurately. Depositing CVD diamond coating on the
cemented carbide with high cobalt content can improve its toughness
and strength, therefore, it is very important to research on the
preparation technology and cutting properties of CVD diamond coated
cemented carbide cutting tool with high cobalt content. The
preparation technology of boron-doped diamond (BDD) coating has
been studied and the coated drills were prepared. BDD coating were
deposited on the drills by using the optimized parameters and the SEM
results show that there are no cracks or collapses in the coating.
Cutting tests with the prepared drills against the silumin and aluminum
base printed circuit board (PCB) have been studied. The results show
that the wear amount of the coated drill is small and the machined
surface has a better precision. The coating does not come off during
the test, which shows good adhesion and cutting performance of the
drill.
Abstract: Solid waste management in steel industry is broadly
classified in “4 Rs” i.e. reduce, reuse, recycle and restore the
materials. Reuse and recycling the entire solid waste generated in the
process of steel making is a viable solution in targeting a clean, green
and zero waste technology leading to sustainable development of the
steel industry. Solid waste management has gained importance in
steel industry in view of its uncertainty, volatility and speculation due
to world competitive standards, rising input costs, scarcity of raw
materials and solid waste generated like in other sectors. The
challenges that the steel Industry faces today are the requirement of a
sustainable development by meeting the needs of our present
generation without compromising the ability of future generations.
Technologies are developed not only for gainful utilization of solid
wastes in manufacture of conventional products but also for
conversion of same in to completely new products.
Abstract: The purpose of the present work was to develop an
innovative food product with nutritional properties as well as
appealing organoleptic qualities. The product, a jam, was prepared
with the beans’ cooking water combined with fresh apple or carrot,
without the addition of any conservatives. Three different jams were
produced: bean and carrot, bean and apple and bean, apple and
cinnamon. The developed products underwent a sensorial analysis
that revealed that the bean, apple and cinnamon jam was globally
better accepted. However, with this study, the consumers determined
that the bean and carrot jam had the most attractive color and the
bean and apple jam the better consistency. Additionally, it was
possible to analyze the jams for their chemical components, namely
fat, fiber, protein, sugars and antioxidant activity. The obtained
results showed that the bean and carrot jam had the highest lipid
content, while the bean, apple and cinnamon jam had the highest
fiber content, when compared to the other two jams. Regarding the
sugar content, both jams with apple revealed similar sugar values,
which were higher than the sugar content of the bean and carrot jam.
The antioxidant activity was on average 10 mg TE/g.
Abstract: The paper describes the OAS role in dispute
resolution. The authors make an attempt to identify a general pattern
of the OAS activities within the peaceful settlement of interstate
conflicts, in the beginning of 21st century, as well as to analyze some
features of Honduras–Belize, Nicaragua–Honduras, Honduras–El
Salvador, Costa-Rica–Nicaragua, Colombia–Ecuador cases.
Abstract: Advances in the use of health care technology have
resulted in increased adverse events (AEs) related to the use of
medical devices. The study focused on the existing reporting systems.
This study was conducted in a tertiary care public sector hospital.
Devices included Syringe infusion pumps, Cardiac monitors, Pulse
oximeters, Ventilators and Defibrillators. A total of 211 respondents
were recruited. Interviews were held with 30 key informants. Medical
records were scrutinized. Relevant statistical tests were used.
Resident doctors reported maximum frequency of AEs, followed
by nurses; and least by consultants. A significant association was
found between the cadre of health care personnel and awareness that
the patients and bystanders have a risk of sustaining AE. Awareness
regarding reporting of AEs was low, and it was generally done
verbally. Other critical findings are discussed in the light of the
barriers to reporting, reasons for non-compliance, recording system,
and so on.
Abstract: The Markov decision process (MDP) based
methodology is implemented in order to establish the optimal
schedule which minimizes the cost. Formulation of MDP problem
is presented using the information about the current state of pipe,
improvement cost, failure cost and pipe deterioration model. The
objective function and detailed algorithm of dynamic programming
(DP) are modified due to the difficulty of implementing the
conventional DP approaches. The optimal schedule derived from
suggested model is compared to several policies via Monte
Carlo simulation. Validity of the solution and improvement in
computational time are proved.
Abstract: This study aimed to identify the alignment of
understanding and assessment practices among secondary school
teachers. The study was carried out using quantitative descriptive
study. The sample consisted of 164 teachers who taught Form 1 and 2
from 11 secondary schools in the district of North Kinta, Perak,
Malaysia. Data were obtained from 164 respondents who answered
Expectation Alignment Understanding and Practices of School
Assessment (PEKDAPS) questionnaire. The data were analysed
using SPSS 17.0+. The Cronbach’s alpha value obtained through
PEKDAPS questionnaire pilot study was 0.86. The results showed
that teachers' performance in PEKDAPS based on the mean value
was less than 3, which means that perfect alignment does not occur
between the understanding and practices of school assessment. Two
major PEKDAPS sub-constructs of articulation across grade and age
and usability of the system were higher than the moderate alignment
of the understanding and practices of school assessment (Min=2.0).
The content focused of PEKDAPs sub-constructs which showed
lower than the moderate alignment of the understanding and practices
of school assessment (Min=2.0). Another two PEKDAPS subconstructs
of transparency and fairness and the pedagogical
implications showed moderate alignment (2.0). The implications of
the study is that teachers need to fully understand the importance of
alignment among components of assessment, learning and teaching
and learning objectives as strategies to achieve quality assessment
process.
Abstract: Over the years, it has been extensively established that
the practice of assuming a structure being fixed at base, leads to gross
errors in evaluation of its overall response due to dynamic loadings
and overestimations in design. The extent of these errors depends on
a number of variables; soil type being one of the major factor. This
paper studies the effect of Soil Structure Interaction (SSI) on multistorey
buildings with varying under-laying soil types after proper
validation of the effect of SSI. Analysis for soft, stiff and very stiff
base soils has been carried out, using a powerful Finite Element
Method (FEM) software package ANSYS v14.5. Results lead to
some very important conclusions regarding time period, deflection
and acceleration responses.
Abstract: Background: The objectives of this study were to
assess patient’s knowledge of appropriate sublingual glyceryl
trinitrate (GTN) use as well as to investigate how patients commonly
store and carry their sublingual GTN tablets. Methodology: This was
a cross-sectional survey, using a validated researcher-administered
questionnaire. The study involved cardiac patients receiving
sublingual GTN attending the outpatient and inpatient departments of
Taiping Hospital, a non-academic public care hospital. The minimum
calculated sample size was 92, but 100 patients were conveniently
sampled. Respondents were interviewed on 3 areas, including
demographic data, knowledge and use of sublingual GTN. Eight
items were used to calculate each subject’s knowledge score and six
items were used to calculate use score. Results: Of the 96 patients
who consented to participate, majority (96.9%) were well aware of
the indication of sublingual GTN. With regards to the mechanism of
action of sublingual GTN, 73 (76%) patients did not know how the
medication works. Majority of the patients (66.7%) knew about the
proper storage of the tablet. In relation to the maximum number of
sublingual GTN tablets that can be taken during each angina episode,
36.5% did not know that up to 3 tablets of sublingual GTN can be
taken during each episode of angina. Fifty four (56.2%) patients were
not aware that they need to replace sublingual GTN every 8 weeks
after receiving the tablets. Majority (69.8%) of the patients
demonstrated lack of knowledge with regards to the use of sublingual
GTN as prevention of chest pain. Conclusion: Overall, patients’
knowledge regarding the self-administration of sublingual GTN is
still inadequate. The findings support the need for more frequent
reinforcement of patient education, especially in the areas of
preventive use, storage and drug stability.
Abstract: Cemented carbide balls are usually implemented in
industry under the environment of high speed, high temperature,
corrosiveness and strong collisions. However, its application is limited
due to high fabrication cost, processing efficiency and quality. A novel
eccentric lapping method with two rotatable lapping plates was
proposed in this paper. A mathematical model was constructed to
analyze the influence of each design parameter on this lapping method.
To validate this new lapping method, an orthogonal experiment was
conducted with cemented carbide balls (YG6). The simulation model
was verified and the optimal lapping parameters were derived. The
results show that the surface roundness of the balls reaches to 0.65um
from 2um in 1 hour using this lapping method. So, using this novel
lapping method, it can effectively improve the machining precision
and efficiency of cemented carbide balls.
Abstract: Knowledge is considered as an important asset which
can help organizations to create competitive advantage. The necessity
of taking care of these assets is more important in these days – in
days of turbulent changes in business environment. Knowledge could
facilitate adaption to constant changes. The aim of this paper is to
describe how the knowledge sharing can be supported in the
manufacturing companies. The methods of case studies and grounded
theory were used to present information gained by carrying out semistructured
interviews. Results show that knowledge sharing is
supported in very similar ways in respondent companies.