Abstract: In this study, we have defined slant helix according to
Bishop frame in Euclidean 3-Space. Furthermore, we have given
some necassary and sufficient conditons for the slant helix.
Abstract: The objective of this work is to study the influence of the properties of the substrate on the retrofit (thin repair) of damaged concrete elements, with the SCC. Fluidity, principal characteristic of the SCC, would enable it to cover and adhere to the concrete to be repaired. Two aspects of repair are considered, the bond (Adhesion) and the tensile strength and the cracking. The investigation is experimental; It was conducted over test specimens made up of ordinary concrete prepared and hardened in advance (the material to be repaired) over which a self compacting concrete layer is cast. Three alternatives of SC concrete and one ordinary concrete (comparison) were tested. It appears that the self-compacting concrete constitutes a good material for repairing. It follows perfectly the surfaces- forms to be repaired and allows a perfect bond. Fracture tests made on specimens of self-compacting concrete show a brittle behaviour. However when a small percentage of fibres is added, the resistance to cracking is very much improve.
Abstract: Deprivation indices are widely used in public health
study. These indices are also referred as the index of inequalities or
disadvantage. Even though, there are many indices that have been
built before, it is believed to be less appropriate to use the existing
indices to be applied in other countries or areas which had different
socio-economic conditions and different geographical characteristics.
The objective of this study is to construct the index based on the
geographical and socio-economic factors in Peninsular Malaysia
which is defined as the weighted household-based deprivation index.
This study has employed the variables based on household items,
household facilities, school attendance and education level obtained
from Malaysia 2000 census report. The factor analysis is used to
extract the latent variables from indicators, or reducing the
observable variable into smaller amount of components or factor.
Based on the factor analysis, two extracted factors were selected,
known as Basic Household Amenities and Middle-Class Household
Item factor. It is observed that the district with a lower index values
are located in the less developed states like Kelantan, Terengganu
and Kedah. Meanwhile, the areas with high index values are located
in developed states such as Pulau Pinang, W.P. Kuala Lumpur and
Selangor.
Abstract: Deep cold rolling (DCR) and low plasticity burnishing (LPB) process are cold working processes, which easily produce a smooth and work-hardened surface by plastic deformation of surface irregularities. The present study focuses on the surface roughness and surface hardness aspects of AISI 4140 work material, using fractional factorial design of experiments. The assessment of the surface integrity aspects on work material was done, in order to identify the predominant factors amongst the selected parameters. They were then categorized in order of significance followed by setting the levels of the factors for minimizing surface roughness and/or maximizing surface hardness. In the present work, the influence of main process parameters (force, feed rate, number of tool passes/overruns, initial roughness of the work piece, ball material, ball diameter and lubricant used) on the surface roughness and the hardness of AISI 4140 steel were studied for both LPB and DCR process and the results are compared. It was observed that by using LPB process surface hardness has been improved by 167% and in DCR process surface hardness has been improved by 442%. It was also found that the force, ball diameter, number of tool passes and initial roughness of the workpiece are the most pronounced parameters, which has a significant effect on the work piece-s surface during deep cold rolling and low plasticity burnishing process.
Abstract: Compensating physiological motion in the context
of minimally invasive cardiac surgery has become an attractive
issue since it outperforms traditional cardiac procedures offering
remarkable benefits. Owing to space restrictions, computer vision
techniques have proven to be the most practical and suitable solution.
However, the lack of robustness and efficiency of existing methods
make physiological motion compensation an open and challenging
problem. This work focusses on increasing robustness and efficiency
via exploration of the classes of 1−and 2−regularized optimization,
emphasizing the use of explicit regularization. Both approaches are
based on natural features of the heart using intensity information.
Results pointed out the 1−regularized optimization class as the best
since it offered the shortest computational cost, the smallest average
error and it proved to work even under complex deformations.
Abstract: e-Government is already in its second decade. Prerequisite for further development and adaptation to new realities is the optimal management of administrative information and knowledge production by those involved, i.e. the public sector, citizens and businesses. Nowadays, the amount of information displayed or distributed on the Internet has reached enormous dimensions, resulting in serious difficulties when extracting and managing knowledge. The semantic web is expected to play an important role in solving this problem and the technologies that support it. In this article, we address some relevant issues.
Abstract: Some methodologies were compared in providing
erosion maps of surface, rill and gully and erosion features, in
research which took place in the Varamin sub-basin, north-east
Tehran, Iran. A photomorphic unit map was produced from
processed satellite images, and four other maps were prepared by the
integration of different data layers, including slope, plant cover,
geology, land use, rocks erodibility and land units. Comparison of
ground truth maps of erosion types and working unit maps indicated
that the integration of land use, land units and rocks erodibility layers
with satellite image photomorphic units maps provide the best
methods in producing erosion types maps.
Abstract: The objective of this study is to evaluate the
occurrence of fungi in aerobic and anoxic activated sludge from
membrane bioreactors (MBRs). Thirty-six samples of both aerobic
and anoxic activated sludge were taken from 2 MBR treating
domestic wastewater. Over a period of eight months 2 samples from
each plant were taken per month. The samples were prepared for
count and definition of fungi. The obtained data show that, sixty
species belonging to 27 genera were collected from activated sludge
samples under aerobic and anoxic conditions. Regarding to the fungi
definition, under aerobic condition the Geotrichum was found at
(8.8%) followed by Penicillium (75.0%), Yeasts (65.7%) and
Trichoderma (55.5%), while Yeasts (77.1%) Geotrichum
candidumand Penicillium (61.1%) species were the most prevalent in
anoxic activated sludge. The results indicate that activated sludge is
habitat for growth and sporulation of different groups of fungi, both
saprophytic and pathogenic.
Abstract: This paper is based on a study conducted in 2006 to assess the impact of computer usage on health of National Institute for Medical Research (NIMR) staff. NIMR being a research Institute, most of its staff spend substantial part of their working time on computers. There was notion among NIMR staff on possible prolonged computer usage health hazards. Hence, a study was conducted to establish facts and possible mitigation measures. A total of 144 NIMR staff were involved in the study of whom 63.2% were males and 36.8% females aged between 20 and 59 years. All staff cadres were included in the sample. The functions performed by Institute staff using computers includes; data management, proposal development and report writing, research activities, secretarial duties, accounting and administrative duties, on-line information retrieval and online communication through e-mail services. The interviewed staff had been using computers for 1-8 hours a day and for a period ranging from 1 to 20 years. The study has indicated ergonomic hazards for a significant proportion of interviewees (63%) of various kinds ranging from backache to eyesight related problems. The authors highlighted major issues which are substantially applicable in preventing occurrences of computer related problems and they urged NIMR Management and/or the government of Tanzania opts to adapt their practicability.
Abstract: Gasoline Octane Number is the standard measure of
the anti-knock properties of a motor in platforming processes, that is
one of the important unit operations for oil refineries and can be
determined with online measurement or use CFR (Cooperative Fuel
Research) engines. Online measurements of the Octane number can
be done using direct octane number analyzers, that it is too
expensive, so we have to find feasible analyzer, like ANFIS
estimators.
ANFIS is the systems that neural network incorporated in fuzzy
systems, using data automatically by learning algorithms of NNs.
ANFIS constructs an input-output mapping based both on human
knowledge and on generated input-output data pairs.
In this research, 31 industrial data sets are used (21 data for training
and the rest of the data used for generalization). Results show that,
according to this simulation, hybrid method training algorithm in
ANFIS has good agreements between industrial data and simulated
results.
Abstract: Sedimentation in reservoirs and the corresponding
loss of storage capacity is one of the most serious problems in dam
engineering. Pressurized flushing, a way to remove sediments from the reservoir, is flushing under a pressurized flow condition and
nearly constant water level. Pressurized flushing has only local
effects around the outlet. Sediment in the vicinity of the outlet openings is scoured and a funnel shaped crater is created. In this study, the temporal development of flushing cone under various
hydraulic conditions was studied experimentally. Time variations of
parameters such as maximum length and width of flushing and also
depth of scouring cone was measured. Results indicated that an
increase in flow velocity (and consequently in Froude number)
established new hydraulically conditions for flushing mechanism and
so a sudden growth was observed in the amount of sediment released
and also scouring dimenssions. In addition, a set of nondimensional
relationships were identified for temporal variations of flushing scour
dimenssions, which can eventuallt be used to estimate the development of flushing cone.
Abstract: One-way functions are functions that are easy to
compute but hard to invert. Their existence is an open conjecture; it
would imply the existence of intractable problems (i.e. NP-problems
which are not in the P complexity class).
If true, the existence of one-way functions would have an impact
on the theoretical framework of physics, in particularly, quantum
mechanics. Such aspect of one-way functions has never been shown
before.
In the present work, we put forward the following.
We can calculate the microscopic state (say, the particle spin in the
z direction) of a macroscopic system (a measuring apparatus
registering the particle z-spin) by the system macroscopic state (the
apparatus output); let us call this association the function F. The
question is: can we compute the function F in the inverse direction?
In other words, can we compute the macroscopic state of the system
through its microscopic state (the preimage F -1)?
In the paper, we assume that the function F is a one-way function.
The assumption implies that at the macroscopic level the Schrödinger
equation becomes unfeasible to compute. This unfeasibility plays a
role of limit of the validity of the linear Schrödinger equation.
Abstract: In recent years, environment regulation forcing
manufactures to consider recovery activity of end-of- life products
and/or return products for refurbishing, recycling,
remanufacturing/repair and disposal in supply chain management. In
this paper, a mathematical model is formulated for single product
production-inventory system considering remanufacturing/reuse of
return products and rate of return products follows a demand like
function, dependent on purchasing price and acceptance quality level.
It is useful in decision making to determine whether to go for
remanufacturing or disposal of returned products along with newly
produced products to satisfy a stationary demand. In addition, a
modified genetic algorithm approach is proposed, inspired by particle
swarm optimization method. Numerical analysis of the case study is
carried out to validate the model.
Abstract: The continued interest in the use of distributed generation in recent years is leading to the growth in number of distributed generators connected to distribution networks. Steady state voltage rise resulting from the connection of these generators can be a major obstacle to their connection at lower voltage levels. The present electric distribution network is designed to keep the customer voltage within tolerance limit. This may require a reduction in connectable generation capacity, under utilization of appropriate generation sites. Thus distribution network operators need a proper voltage regulation method to allow the significant integration of distributed generation systems to existing network. In this work a voltage rise problem in a typical distribution system has been studied. A method for voltage regulation of distribution system with multiple DG system by coordinated operation distributed generator, capacitor and OLTC has been developed. A sensitivity based analysis has been carried out to determine the priority for individual generators in multiple DG environment. The effectiveness of the developed method has been evaluated under various cases through simulation results.
Abstract: The study describes chitosan membrane platform
modified with nanostructure pattern which using nanotechnology to
fabricate. The cell-substrate interaction between neuro-2a neuroblasts
cell lines and chitosan membrane (flat, nanostructure and
nanostructure pattern types) was investigated. The adhered
morphology of neuro-2a cells depends on the topography of chitosan
surface. We have found that neuro-2a showed different morphogenesis
when cells adhered on flat and nanostructure chitosan membrane. The
cell projected area of neuro-2a on flat chitosan membrane is larger
than on nanostructure chitosan membrane. In addition, neuro-2a cells
preferred to adhere on flat chitosan surface region than on
nanostructure chitosan membrane to immobilize and differentiation.
The experiment suggests surface topography can be used as a critical
mechanism to isolate group of neuro-2a to a particular rectangle area
on chitosan membrane. Our finding will provide a platform to take
patch clamp to record electrophysiological behavior about neurons in
vitro in the future.
Abstract: Rapid Application Development (RAD) enables ever
expanding needs for speedy development of computer application
programs that are sophisticated, reliable, and full-featured. Visual
Basic was the first RAD tool for the Windows operating system, and
too many people say still it is the best. To provide very good
attraction in visual basic 6 applications, this paper directing to use
VRML scenes over the visual basic environment.
Abstract: Standard packaging and interconnection technologies
of power devices have difficulties meeting the increasing thermal
demands of new application fields of power electronics devices.
Main restrictions are the decreasing reliability of bond-wires and
solder layers with increasing junction temperature. In the last few
years intensive efforts have been invested in developing new
packaging and interconnection solutions which may open a path to
future application of power devices. In this paper, the main failure
mechanisms of power devices are described and principle of new
packaging and interconnection concepts and their power cycling
reliability are presented.
Abstract: In this paper we present two novel 1-bit full adder
cells in dynamic logic style. NP-CMOS (Zipper) and Multi-Output
structures are used to design the adder blocks. Characteristic of
dynamic logic leads to higher speeds than the other standard static
full adder cells. Using HSpice and 0.18┬Ám CMOS technology
exhibits a significant decrease in the cell delay which can result in a
considerable reduction in the power-delay product (PDP). The PDP
of Multi-Output design at 1.8v power supply is around 0.15 femto
joule that is 5% lower than conventional dynamic full adder cell and
at least 21% lower than other static full adders.
Abstract: Fermented beverages have high expression in the
market for beverages in general, is increasingly valued in situations
where the characteristic aroma and flavor of the material that gave
rise to them are kept after processing. This study aimed to develop a
distilled beverage from passion fruit, and assess, by sensory tests and
chromatographic profile, the influence of different treatments (FM1-
spirit with pulp addiction and FM2 – spirit with bigger ratio of pulp
in must) in the setting of volatiles in the fruit drink, and performing
chemical characterization taking into account the main parameters of
quality established by the legislation. The chromatograms and the
first sensorial tests had indicated that sample FM1 possess better
characteristics of aroma, as much of how much quantitative the
qualitative point of view. However, it analyzes it sensorial end
(preference test) disclosed the biggest preference of the cloth provers
for sample FM2-2 (note 7.93), being the attributes of decisive color
and flavor in this reply, confirmed for the observed values lowest of
fixed and total acidity in the samples of treatment FM2.
Abstract: Two freshwater fishes, Rasbora sumatrana
(Cyprinidae) and Poecilia reticulata (guppy) (Poeciliidae) were
exposed for a four-day period in the laboratory condition to a range
of copper (Cu) and cadmium (Cd) concentrations. Mortality was
assessed and median lethal concentrations (LC50) were calculated.
LC50 increased with decrease in mean exposure times for both metals.
For R. sumatrana, LC50s for 24, 48, 72 and 96 hours for Cu were
54.2, 30.3, 18.9 and 5.6 μg/L and for Cd 1440.2, 459.3, 392.3 and
101.6 μg/L respectively. For P. reticulata, LC50s for 24, 48, 72 and
96 hours for Cu were 348.9, 145.4, 61.3 and 37.9 μg/L and for Cd
8205.6, 2827.1, 405.8 and 168.1 μg/L, respectively. Results indicated
that the Cu was more toxic than Cd to both fishes (Cu>Cd) and R.
sumatrana was more sensitive than P. reticulata to the metals.