Abstract: This study has been presented which is a detailed
work of seismic microzonation of the city center. For seismic
microzonation area of 225 km2 has been selected as the study area.
MASW (Multichannel analysis of surface wave) and seismic
refraction methods have been used to generate one-dimensional shear
wave velocity profile at 250 locations and two-dimensional profile at
60 locations. These shear wave velocities are used to estimate
equivalent shear wave velocity in the study area at every 2 and 5 m
intervals up to a depth of 60 m. Levels of equivalent shear wave
velocity of soil are used the classified of the study area. After the
results of the study, it must be considered as components of urban
planning and building design of Denizli and the application and use
of these results should be required and enforced by municipal
authorities.
Abstract: A wireless sensor network (WSN) is a collection of
sensor nodes organized into a cooperative network. These nodes
communicate through a wireless antenna. Reduction in physical size
and multiband operation is an important requirement of WSN
antenna. Fractal antenna is used for miniaturization and multiband
operation. The self-similar or self-affine and space filling property of
fractal geometry increases the effective electrical length of the
antenna, reduces the size and make them frequency independent. This
paper elaborates on Dual band fractal antenna with Coplanar
Waveguide (CPW) feed for WSN. The proposed antenna is designed
on a FR4 substrate with the dimension of 27mm x 28.5mm x 1.6mm,
resonates at 2.4GHz and 5.2GHz with a return loss less than -10dB.
The design and simulation process is carried out using IE3D
simulation software. The simulated and measured results are found in
good agreement.
Abstract: This article presents a new vibration diagnostic
method designed to (PM) machines with permanent magnets. Those
devices are commonly used in small wind and water systems or
vehicles drives. The author’s method is very innovative and unique.
Specific structural properties of PM machines are used in this method
- electromotive force (EMF) generated due to vibrations. There was
analysed number of publications which describe vibration diagnostic
methods and tests of electrical PM machines and there was no
method found to determine the technical condition of such machine
basing on their own signals. In this article will be discussed: the
method genesis, the similarity of machines with permanent magnet to
vibration sensor and simulation and laboratory tests results. The
method of determination the technical condition of electrical machine
with permanent magnets basing on its own signals is the subject of
patent application and it is the main thesis of author’s doctoral
dissertation.
Abstract: This research focuses on the optimization of glazed
surfaces and the assessment of possible solar gains in industrial
buildings. Existing window rating methods for single windows were
evaluated and a new method for a simple analysis of energy gains and
losses by single windows was introduced. Furthermore extensive
transient building simulations were carried out to appraise the
performance of low cost polycarbonate multi-cell sheets in
interaction with typical buildings for industrial applications. Mainly
energy saving potential was determined by optimizing the orientation
and area of such glazing systems in dependency on their thermal
qualities. Moreover the impact on critical aspects such as summer
overheating and daylight illumination was considered to ensure the
user comfort and avoid additional energy demand for lighting or
cooling. Hereby the simulated heating demand could be reduced by
up to 1/3 compared to traditional architecture of industrial halls using
mainly skylights.
Abstract: Theoretical optimization of a copper-water negative
inclination heat pipe with internal composite wick structure had been
performed, regarding a new introduced parameter: the ratio between
the coarse mesh wraps and the fine mesh wraps of the composite
wick. Since in many cases, the design of a heat pipe matches specific
thermal requirements and physical limitations, this work
demonstrates the optimization of a 1m length, 8mm internal diameter
heat pipe without an adiabatic section, at a negative inclination angle
of -10º. The optimization is based on a new introduced parameter, LR:
the ratio between the coarse mesh wraps and the fine mesh wraps.
Abstract: Information and Communication Technologies (ICTs)
are pervasive nowadays, including in education where they are
expected to improve the performance of learners. However, the hope
placed in ICTs to find viable solutions to the problem of poor
academic performance in schools in the developing world has not yet
yielded the expected benefits. This problem serves as a motivation to
this study whose aim is to examine the perceptions of educators on
the advantages and disadvantages of e-learning. This aim will be
subdivided into two types of research objectives. Objectives on the
identification and design of theories and models will be achieved
using content analysis and literature review. However, the objective
on the empirical testing of such theories and models will be achieved
through the survey of educators from different schools in the
Pinetown District of the South African Kwazulu-Natal province.
SPSS is used to quantitatively analyse the data collected by the
questionnaire of this survey using descriptive statistics and Pearson
correlations after assessing the validity and the reliability of the data.
The main hypothesis driving this study is that there is a relationship
between the demographics of educators’ and their adherence to
learning theories on one side, and their perceptions on the advantages
and disadvantages of e-learning on the other side, as argued by
existing research; but this research views these learning theories
under three perspectives: educators’ adherence to self-regulated
learning, to constructivism, and to progressivism. This hypothesis
was fully confirmed by the empirical study except for the
demographic factor where teachers’ level of education was found to
be the only demographic factor affecting the perceptions of educators
on the advantages and disadvantages of e-learning.
Abstract: This paper presents a new method to design nonlinear
feedback linearization controller for PEMFCs (Polymer Electrolyte
Membrane Fuel Cells). A nonlinear controller is designed based on
nonlinear model to prolong the stack life of PEMFCs. Since it is
known that large deviations between hydrogen and oxygen partial
pressures can cause severe membrane damage in the fuel cell,
feedback linearization is applied to the PEMFC system so that the
deviation can be kept as small as possible during disturbances or load
variations. To obtain an accurate feedback linearization controller,
tuning the linear parameters are always important. So in proposed
study NSGA (Non-Dominated Sorting Genetic Algorithm)-II method
was used to tune the designed controller in aim to decrease the
controller tracking error. The simulation result showed that the
proposed method tuned the controller efficiently.
Abstract: Well-designed composite steel and concrete structures
highlight the good material properties and lower the deficiencies of
steel and concrete, in particular they make use of high tensile strength
of steel and high stiffness of concrete. The most common composite
steel and concrete structure is a simply supported beam, which
concrete slab transferring the slab load to a beam is connected to the
steel cross-section. The aim of this paper is to find the most adequate
numerical model of a simply supported composite beam with the
cross-sectional and material parameters based on the results of a
processed parametric study and numerical analysis. The paper also
evaluates the suitability of using compact concrete with the
lightweight aggregates for composite steel and concrete beams. The
most adequate numerical model will be used in the resent future to
compare the results of laboratory tests.
Abstract: Diabetes is a growing health problem in worldwide.
Especially, the patients with Type 1 diabetes need strict glycemic
control because they have deficiency of insulin production. This
paper attempts to control blood glucose based on body mathematical
body model. The Bergman minimal mathematical model is used to
develop the nonlinear controller. A novel back-stepping based sliding
mode control (B-SMC) strategy is proposed as a solution that
guarantees practical tracking of a desired glucose concentration. In
order to show the performance of the proposed design, it is compared
with conventional linear and fuzzy controllers which have been done
in previous researches. The numerical simulation result shows the
advantages of sliding mode back stepping controller design to linear
and fuzzy controllers.
Abstract: The mathematical analysis on radiation obtained and
the development of the solar photovoltaic (PV) array groundwater
pumping is needed in the rural areas of Thohoyandou for sizing and
power performance subject to the climate conditions within the area.
A simple methodology approach is developed for the directed
coupled solar, controller and submersible ground water pump system.
The system consists of a PV array, pump controller and submerged
pump, battery backup and charger controller. For this reason, the
theoretical solar radiation is obtained for optimal predictions and
system performance in order to achieve different design and
operating parameters. Here the examination of the PV schematic
module in a Direct Current (DC) application is used for obtainable
maximum solar power energy for water pumping. In this paper, a
simple efficient photovoltaic water pumping system is presented with
its theoretical studies and mathematical modeling of photovoltaics
(PV) system.
Abstract: The article presents the concept of an electromagnetic
circuit generator with permanent magnets mounted on the surface
rotor core designed for single phase work. Computation field-circuit
model was shown. The spectrum of time course of voltages in the
idle work was presented. The cross section with graphically
presentation of magnetic induction in particular parts of
electromagnetic circuits was presented. Distribution of magnetic
induction at the rated load point for each phase was shown. The time
course of voltages and currents for each phases for rated power were
displayed. An analysis of laboratory results and measurement of load
characteristics of the generator was discussed. The work deals with
three electromagnetic circuits of generators with permanent magnet
where output voltage characteristics versus rated power were
expressed.
Abstract: The success of any retail business is predisposed by its
swift response and its knack in understanding the constraints and the
requirements of customers. In this paper a conceptual design model
of an automated customer-friendly supermarket has been proposed.
In this model a 10-sided, space benefited, regular polygon shaped
gravity shelves have been designed for goods storage and effective
customer-specific algorithms have been built-in for quick automatic
delivery of the randomly listed goods. The algorithm is developed
with two main objectives, viz., delivery time and priority. For
meeting these objectives the randomly listed items are reorganized
according to the critical-path of the robotic arm specific to the
identified shop and its layout and the items are categorized according
to the demand, shape, size, similarity and nature of the product for an
efficient pick-up, packing and delivery process. We conjectured that
the proposed automated supermarket model reduces business
operating costs with much customer satisfaction warranting a winwin
situation.
Abstract: An anthropometric study applied to 1,115 students of
the Faculty of Chemical Sciences and Engineering of the
Autonomous University of California. Thirteen individual
measurements were taken in a sitting position. The results obtained
allow forming a reliable anthropometric database for statistical
studies and analysis and inferences of specific distributions, so the
opinion of experts in occupational medicine recommendations may
emit to reduce risks resulting in an alteration of the vital signs during
the execution of their school activities. Another use of these analyses
is to use them as a reliable reference for future deeper research, to the
design of spaces, tools, utensils, workstations, with anthropometric
dimensions and ergonomic characteristics suitable to use.
Abstract: This paper presents an anthropometric study
conducted to 300 employees in a maquiladora industry that belongs
to the cluster of medical products as part of a research project to
pretend simulate workplace conditions under which operators
conduct their activities. This project is relevant because traditionally
performed a study to design ergonomic workspaces according to
anthropometric profile of users, however, this paper demonstrates the
importance of making decisions when the infrastructure cannot be
adapted for economic whichever put emphasis on user activity.
Abstract: In this work, we propose the application of Japanese
“Origami” art for a floating function of a small aerial vehicle such as a
hexarotor. A preliminary experiment was conducted using Origami
magic balls mounted under a hexarotor. This magic ball can expand
and shrink using an air pump during free flying. Using this interesting
and functional concept, it promises to reduce the resistance of wind as
well as reduce the energy consumption when the Origami balls are
deflated. This approach can be particularly useful in rescue emergency
situations. Furthermore, there are many unexpected reasons that may
cause the multi-rotor has to land on the surface of water due to
problems with the communication between the aircraft and the ground
station. In addition, a complementary experiment was designed to
prove that the hexarotor can fly maintaining the stability and also,
takes off and lands on the surface of water using air balloons.
Abstract: The study deals with the challenges in developing a
test rig to test the performance of water lubricated journal bearing.
The test rig is designed to simulate the working conditions of the
bearing in order to understand their performance before they are put
in operation. The bearing that is studied is the commercially available
water lubricated bearing which has a rubber liner bonded with a rigid
metal shell. The lubricant enters the bearing axially through a
pressurized inlet tank and exits to an outlet tank which is at
sufficiently low pressure. The load on the bearing is applied through
the dead weight system which acts both in upward and downward
direction so that net load acts on the bearing. The issues in feeding
the lubricant into the bearing from the inlet side and preventing the
leakage of the lubricant is discussed. The application of the load on
the test bearing while maintaining the bearing afloat is also discussed.
Abstract: This paper addresses the reduction of peak to average
power ratio (PAPR) for the OFDM in Mobile-WiMAX physical layer
(PHY) standard. In the process, the best achievable PAPR of 0 dB is
found for the OFDM spectrum using phase modulation technique
which avoids the nonlinear distortion. The performance of the
WiMAX PHY standard is handled by the software defined radio
(SDR) prototype in which GNU Radio and USRP N210 employed as
software and hardware platforms respectively. It is also found that
BER performance is shown for different coding and different
modulation schemes. To empathize wireless propagation in specific
environments, a sliding correlator wireless channel sounding system
is designed by using SDR testbed.
Abstract: This paper deals with the issue of biomass and sorted
municipal waste gasification and cogeneration using hot-air turbo-set.
It brings description of designed pilot plant with electrical output 80
kWe. The generated gas is burned in secondary combustion chamber
located beyond the gas generator. Flue gas flows through the heat
exchanger where the compressed air is heated and consequently
brought to a micro turbine. Except description, this paper brings our
basic experiences from operating of pilot plant (operating parameters,
contributions, problems during operating, etc.). The principal
advantage of the given cycle is the fact that there is no contact
between the generated gas and the turbine. So there is no need for
costly and complicated gas cleaning which is the main source of
operating problems in direct use in combustion engines because the
content of impurities in the gas causes operation problems to the units
due to clogging and tarring of working surfaces of engines and
turbines, which may lead as far as serious damage to the equipment
under operation. Another merit is the compact container package
making installation of the facility easier or making it relatively more
mobile. We imagine, this solution of cogeneration from biomass or
waste can be suitable for small industrial or communal applications,
for low output cogeneration.
Abstract: In this numerical study, we want to present the design
of highly efficient extruded-type heat sink. The symmetrically
arranged extruded-type heat sinks are used instead of a single extruded
or swaged-type heat sink. In this parametric study, the maximum
temperatures, the base temperatures between heaters, and the heat
release rates were investigated with respect to the arrangements of heat
sources, air flow rates, and amounts of heat input. Based on the results
we believe that the use of both side of heat sink is to be much better for
release the heat than the use of single side. Also from the results, it is
believed that the symmetric arrangement of heat sources is
recommended to achieve a higher heat transfer from the heat sink.
Abstract: A method which allows a diabetic quadriplegic patient
that has had four limb amputations (above the knee and elbow) to
self-administer injections of insulin has been designed. The aim of
this research project is to improve a quadriplegic patient’s selfmanagement,
affected by diabetes, by designing a suitable device for
self-administering insulin.
The quadriplegic patient affected by diabetes has to be able to selfadminister
insulin safely and independently to guarantee stable
healthy conditions. The device also should be designed to adapt to a
number of different varying personal characteristics such as height
and body weight.