Abstract: Narrow bandwidth and high loss performance limits the use of reflectarray antennas in some applications. This article reports on the feasibility of employing strategic reflectarray resonant elements to characterize the reflectivity performance of reflectarrays in X-band frequency range. Strategic reflectarray resonant elements incorporating variable substrate thicknesses ranging from 0.016λ to 0.052λ have been analyzed in terms of reflection loss and reflection phase performance. The effect of substrate thickness has been validated by using waveguide scattering parameter technique. It has been demonstrated that as the substrate thickness is increased from 0.508mm to 1.57mm the measured reflection loss of dipole element decreased from 5.66dB to 3.70dB with increment in 10% bandwidth of 39MHz to 64MHz. Similarly the measured reflection loss of triangular loop element is decreased from 20.25dB to 7.02dB with an increment in 10% bandwidth of 12MHz to 23MHz. The results also show a significant decrease in the slope of reflection phase curve as well. A Figure of Merit (FoM) has also been defined for the comparison of static phase range of resonant elements under consideration. Moreover, a novel numerical model based on analytical equations has been established incorporating the material properties of dielectric substrate and electrical properties of different reflectarray resonant elements to obtain the progressive phase distribution for each individual reflectarray resonant element.
Abstract: With short production development times, there is an increased need to demonstrate product reliability relatively quickly with minimal testing. In such cases there may be few if any observed failures. Thus it may be difficult to assess reliability using the traditional reliability test plans that measure only time (or cycles) to failure. For many components, degradation measures will contain important information about performance and reliability. These measures can be used to design a minimal test plan, in terms of number of units placed on test and duration of the test, necessary to demonstrate a reliability goal. In this work we present a case study involving an electronic component subject to degradation. The data, consisting of 42 degradation paths of cycles to failure, are first used to estimate a reliability function. Bootstrapping techniques are then used to perform power studies and develop a minimal reliability test plan for future production of this component.
Abstract: Developments in turbine cooling technology play an important role in increasing the thermal efficiency and the power output of recent gas turbines, in particular the turbojets.
Advanced turbojets operate at high temperatures to improve thermal efficiency and power output. These temperatures are far above the permissible metal temperatures. Therefore, there is a critical need to cool the blades in order to give theirs a maximum life period for safe operation.
The focused objective of this work is to calculate the turbojet performances, as well as the calculation of turbine blades cooling.
The developed application able the calculation of turbojet performances to different altitudes in order to find a point of optimal use making possible to maintain the turbine blades at an acceptable maximum temperature and to limit the local variations in temperatures in order to guarantee their integrity during all the lifespan of the engine.
Abstract: This study presents an Expert System specially designed to be used with Multiobjective Evolutionary Algorithms (MOEAs) for the solution of the portfolio selection problem. The validation of the proposed hybrid System is done by using data sets from Hang Seng 31 in Hong Kong, DAX 100 in Germany and FTSE 100 in UK. The performance of the proposed system is assessed in comparison with the Non-dominated Sorting Genetic Algorithm II (NSGAII). The evaluation of the performance is based on different performance metrics that evaluate both the proximity of the solutions to the Pareto front and their dispersion on it. The results show that the proposed hybrid system is efficient for the solution of this kind of problems.
Abstract: The International Building Code (IBC) and the
California Building Code (CBC) both recognize four basic types of
steel seismic resistant frames; moment frames, concentrically braced
frames, shear walls and eccentrically braced frames. Based on
specified geometries and detailing, the seismic performance of these
steel frames is well understood. In 2011, the authors designed an
innovative steel braced frame system with tapering members in the
general shape of a branching tree as a seismic retrofit solution to an
existing four story “lift-slab” building. Located in the seismically
active San Francisco Bay Area of California, a frame of this
configuration, not covered by the governing codes, would typically
require model or full scale testing to obtain jurisdiction approval.
This paper describes how the theories, protocols, and code
requirements of eccentrically braced frames (EBFs) were employed
to satisfy the 2009 International Building Code (IBC) and the 2010
California Building Code (CBC) for seismically resistant steel frames
and permit construction of these nonconforming geometries.
Abstract: Determination of optimal parameters of a passive
control system device is the primary objective of this study.
Expanding upon the use of control devices in wind and earthquake
hazard reduction has led to development of various control systems.
The advantage of non-linearity characteristics in a passive control
device and the optimal control method using LQR algorithm are
explained in this study. Finally, this paper introduces a simple
approach to determine optimum parameters of a nonlinear viscous
damper for vibration control of structures. A MATLAB program is
used to produce the dynamic motion of the structure considering the
stiffness matrix of the SDOF frame and the non-linear damping
effect. This study concluded that the proposed system (variable
damping system) has better performance in system response control
than a linear damping system. Also, according to the energy
dissipation graph, the total energy loss is greater in non-linear
damping system than other systems.
Abstract: In this work, the main problem considered is the
detection and the isolation of the actuator fault. A new formulation of
the linear system is generated to obtain the conditions of the actuator
fault diagnosis. The proposed method is based on the representation
of the actuator as a subsystem connected with the process system in
cascade manner. The designed formulation is generated to obtain the
conditions of the actuator fault detection and isolation. Detectability
conditions are expressed in terms of the invertibility notions. An
example and a comparative analysis with the classic formulation
illustrate the performances of such approach for simple actuator fault
diagnosis by using the linear model of nuclear reactor.
Abstract: This paper presents the results of an experimental
study on the effects of elevated temperature on compressive and
flexural strength of Normal Strength Concrete (NSC), High Strength
Concrete (HSC) and High Performance Concrete (HPC). In addition,
the specimen mass and volume were measured before and after
heating in order to determine the loss of mass and volume during the
test. In terms of non-destructive measurement, ultrasonic pulse
velocity test was proposed as a promising initial inspection method
for fire damaged concrete structure. 100 Cube specimens for three
grades of concrete were prepared and heated at a rate of 3°C/min up
to different temperatures (150, 250, 400, 600, and 900°C). The results
show a loss of compressive and flexural strength for all the concretes
heated to temperature exceeding 400°C. The results also revealed that
mass and density of the specimen significantly reduced with an
increase in temperature.
Abstract: In this paper a novel method for the detection of
clipping in speech signals is described. It is shown that the new
method has better performance than known clipping detection
methods, is easy to implement, and is robust to changes in signal
amplitude, size of data, etc. Statistical simulation results are
presented.
Abstract: Steam reforming is industrially important as it is
incorporated in several major chemical processes including the
production of ammonia, methanol, hydrogen and ox alcohols. Due to
the strongly endothermic nature of the process, a large amount of heat
is supplied by fuel burning (commonly natural gas) in the furnace
chamber. Reaction conversions, tube catalyst life, energy
consumption and CO2 emission represent the principal factors
affecting the performance of this unit and are directly influenced by
the high operating temperatures and pressures.
This study presents a simulation of the performance of the
reforming of methane in a primary reformer, through a developed
empirical relation which enables to investigate the effects of
operating parameters such as the pressure, temperature, steam to
carbon ratio on the production of hydrogen, as well as the fraction of
non converted methane.
It appears from this analysis that the exit temperature Te, the
operating pressure as well the steam to carbon ratio has an important
effect on the reforming of methane.
Abstract: The outstanding mechanical properties of Carbon
nanotubes (CNTs) have generated great interest for their potential as
reinforcements in high performance cementitious composites. The
main challenge in research is the proper dispersion of carbon
nanotubes in the cement matrix. The present work discusses the role
of dispersion of multiwalled carbon nanotubes (MWCNTs) on the
compressive strength characteristics of hydrated Portland IS 1489
cement paste. Cement-MWCNT composites with different mixing
techniques were prepared by adding 0.2% (by weight) of MWCNTs
to Portland IS 1489 cement. Rectangle specimens of size
approximately 40mm × 40mm ×160mm were prepared and curing of
samples was done for 7, 14, 28 and 35days. An appreciable increase
in compressive strength with both techniques; mixture of MWCNTs
with cement in powder form and mixture of MWCNTs with cement
in hydrated form 7 to 28 days of curing time for all the samples was
observed.
Abstract: The paper presents an analysis of the innovation performance of small and medium-sized furniture enterprises in Bulgaria, accounting for over 97% of the companies in the sector. It contains advanced features of innovation in enterprises, specific features of the furniture industry in Bulgaria and analysis of the results of studies on the topic. The results from studies of three successive periods - 2006-2008; 2008-2010; 2010-2012, during which were studied 594 small and medium-sized furniture enterprises. There are commonly used in the EU definitions and indicators (European Commission, OECD, Oslo Manual), which allows for the comparability of results.
Abstract: Patients under health treatments that involve long
stays at a hospital or health center (e.g. cancer, organ transplants and
severe burns), tend to get bored or depressed because of the lack of
social interaction with family and friends. Such a situation also
affects the evolution and effectiveness of their treatments. In many
cases, the solution to this problem involves extra challenges, since
many patients need to rest quietly (or remain in bed) to their being
contagious. Considering the weak health condition in which usually
are these kinds, keeping them motivated and quiet represents an
important challenge for nurses and caregivers. This article presents a
mobile ubiquitous game called MagicRace, which allows hospitalized
kinds to interact socially with one another without putting to risk
their sensitive health conditions. The game does not require a
communication infrastructure at the hospital, but instead, it uses a
mobile ad hoc network composed of the handheld devices used by
the kids to play. The usability and performance of this application
was tested in two different sessions. The preliminary results show
that users experienced positive feelings from this experience.
Abstract: This paper presents a new control scheme to control a brushless doubly fed induction generator (BDFIG) using back-to-back PWM converters for wind power generation. The proposed control scheme is a New Self-Tuning Fuzzy Proportional-Derivative Controller (NSTFPDC). The goal of BDFIG control is to achieve a similar dynamic performance to the doubly fed induction generator (DFIG), exploiting the well-known induction machine vector control philosophy. The performance of NSTFPDC controller has been investigated and compared with the two controllers, called Proportional–Integral (PI) and PD-like Fuzzy Logic controller (PD-like FLC) based BDFIG. The simulation results demonstrate the effectiveness and the robustness of the NSTFPDC controller.
Abstract: We present in this work the performances of a mobile omnidirectional robot through evaluating its management of the redundancy of actuation. Thus we come to the predictive control implemented.
The distribution of the wringer on the robot actions, through the inverse pseudo of Moore-Penrose, corresponds to a « geometric ›› distribution of efforts. We will show that the load on vehicle wheels would not be equi-distributed in terms of wheels configuration and of robot movement.
Thus, the threshold of sliding is not the same for the three wheels of the vehicle. We suggest exploiting the redundancy of actuation to reduce the risk of wheels sliding and to ameliorate, thereby, its accuracy of displacement. This kind of approach was the subject of study for the legged robots.
Abstract: This paper presents experimental investigation carried out on an unmodified four stroke diesel engine running with preheated straight vegetable oil (SVO) of Karanja. The viscosity of straight karanja oil was reduced by preheating the oil up to 1600C under different load condition. The preheating was done with the help of a Shell and Tube heat exchanger equipment without using any external power source. The heat exchanger was designed in the lab and the heating source was by waste exhaust gas from engine. The experimental results data were analyzed by using 20% blends of svo of Karanja with 80% diesel by volume and 100% preheated svo of karanja for various parameters like specific fuel consumption, brake thermal efficiency and emission of exhaust gas like CO, CO2, HC and NOx. The results indicated that by using straight karanja oil, the emission parameter increases as compared to diesel but regarding engine performance it was found to be very close to that of diesel. All total it can be a replacement of diesel with a small efficiency drop.
Abstract: In the literature, surfing technique has been proposed for single ended wave-pipelined serial interconnects to increase the data transfer rate. In this paper a novel surfing technique is proposed for differential wave-pipelined serial interconnects, which uses a 'Controllable inverter pair' for surfing. To evaluate the efficiency of this technique, a transceiver with transmitter, receiver, delay locked loop (DLL) along with 40mm metal 4 interconnects using the proposed surfing technique is implemented in UMC 180nm technology and their performances are studied through post layout simulations. From the study, it is observed that the proposed scheme permits 1.875 times higher data transmission rate compared to the single ended scheme whose maximum data transfer rate is 1.33 GB/s. The proposed scheme has the ability to receive the correct data even with stuck-at-faults in the complementary line.
Abstract: This paper proposes a hierarchical hidden Markov model (HHMM) to model the detection of M vehicles in a wireless sensor network (WSN). The HHMM model contains an extra level of hidden Markov model to model the temporal transitions of each
state of the first HMM. By modeling the temporal transitions, only those hypothesis with nonzero transition probabilities needs to be tested. Thus, this method efficiently reduces the computation load, which is preferable in WSN applications.This paper integrates several techniques to optimize the detection performance. The output of the states of the first HMM is modeled as Gaussian Mixture Model (GMM), where the number of states and the number of Gaussians are experimentally determined, while the other parameters are estimated using Expectation Maximization (EM). HHMM is used to model the sequence of the local decisions which are based on multiple hypothesis testing with maximum likelihood approach. The states in the HHMM represent various combinations of vehicles of different types. Due to the statistical advantages of multisensor data fusion, we propose a heuristic based on fuzzy weighted majority voting to enhance cooperative classification of moving vehicles within a region that is monitored by a wireless sensor network. A fuzzy inference system weighs each local decision based on the signal to noise
ratio of the acoustic signal for target detection and the signal to noise ratio of the radio signal for sensor communication. The spatial correlation among the observations of neighboring sensor nodes is efficiently utilized as well as the temporal correlation. Simulation results demonstrate the efficiency of this scheme.
Abstract: In this article, coordinated tuning of power system stabilizer (PSS) with static var compensator (SVC) and thyristor controlled series capacitor (TCSC) in multi-machine power system is proposed. The design of proposed coordinated damping controller is formulated as an optimization problem and the controller gains are optimized instantaneously using advanced adaptive particle swarm optimization (AAPSO). The objective function is framed with the inter-area speed deviations of the generators and it is minimized using AAPSO to improve the dynamic stability of power system under severe disturbance. The proposed coordinated controller performance is evaluated under a wide range of system operating conditions with three-phase fault disturbance. Using time domain simulations the damping characteristics of proposed controller is compared with individually tuned PSS, SVC and TCSC controllers. Finally, the real-time simulations are carried out in Opal-RT hardware simulator to synchronize the proposed controller performance in the real world.
Abstract: Cooperative communication systems are considered to be a promising technology to improve the system capacity, reliability and performances over fading wireless channels. Cooperative relaying system with a single antenna will be able to reach the advantages of multiple antenna communication systems. It is ideally suitable for the distributed communication systems; the relays can cooperate and form virtual MIMO systems. Thus the paper will aim to investigate the possible enhancement of cooperated system using decode and forward protocol. On the decode and forward an attempt to cancel or at least reduce the interference instead of increasing the SNR values is achieved. The latter can be achieved via the use group of relays depending on the channel status from source to relay and relay to destination respectively.
In the proposed system, the transmission time has been divided into two phases to be used by the decode and forward protocol. The first phase has been allocated for the source to transmit its data whereas the relays and destination nodes are in receiving mode. On the other hand, the second phase is allocated for the first and second groups of relay nodes to relay the data to the destination node. Simulations results have shown an improvement in performance is achieved compared to the conventional decode and forward in terms of BER and transmission rate.