Abstract: This study investigates the effect of moisture
conditioning on the Indirect Tensile Strength (ITS) of asphalt
concrete. As a first step, cylindrical samples of 100 mm diameter and
50 mm thick were prepared using a Superpave gyratory compactor.
Next, the samples were conditioned using Moisture Induced
Susceptibility Test (MIST) device at different numbers of moisture
conditioning cycles. In the MIST device, samples are subjected water
pressure through the sample pores cyclically. The MIST conditioned
samples were tested for ITS. Results show that the ITS does not
change significantly with MIST conditioning at the specific pressure
and cycles adopted in this study.
Abstract: Recently GPS data is used in a lot of studies to
automatically reconstruct travel patterns for trip survey. The aim is to
minimize the use of questionnaire surveys and travel diaries so as to
reduce their negative effects. In this paper data acquired from GPS and
accelerometer embedded in smart phones is utilized to predict the
mode of transportation used by the phone carrier. For prediction,
Support Vector Machine (SVM) and Adaptive boosting (AdaBoost)
are employed. Moreover a unique method to improve the prediction
results from these algorithms is also proposed. Results suggest that the
prediction accuracy of AdaBoost after improvement is relatively better
than the rest.
Abstract: Fibrin degradation is an important part in prevention
or treatment of intravascular thrombosis and cardiovascular diseases.
Plasmin like fibrinolytic enzymes has given new hope to patient with
cardiovascular diseases by treating fibrin aggregation related diseases
with traditional plasminogen activator which have many side effects.
Various researches involving wide range of sources for production of
fibrinolytic proteases, from bacteria, fungi, insects and fermented
foods. But few have looked into endophytic fungi as a potential
source. Sixteen (16) endophytic fungi were isolated from Hibiscus sp.
leaves from six different locations in Shah Alam, Selangor. Only two
endophytic fungi, FH3 and S13 showed positive fibrinolytic protease
activities. FH3 produced 5.78cm and S13 produced 4.48cm on Skim
Milk Agar after 4 days of incubation at 27°C. Fibrinolytic activity
was observed; 3.87cm and 1.82cm diameter clear zone on fibrin plate
of FH3 and S13 respectively. 18srRNA was done for identification of
the isolated fungi with positive fibrinolytic protease. S13 had the
highest similarity (100%) to that of Penicillium citrinum strain TG2
and FH3 had the highest similarity (99%) to that of Fusarium sp.
FW2PhC1, Fusarium sp. 13002, Fusarium sp. 08006, Fusarium
equiseti strain Salicorn 8 and Fungal sp. FCASAn-2. Media
composition variation showed the effects of carbon nitrogen on
protein concentration, where the decrement of 50% of media
composition caused drastic decrease in protease of FH3 from 1.081 to
0.056 and also S13 from 2.946 to 0.198.
Abstract: The study examines the influence of marital status on
consumers of products and services using blogs as a source of
information. A pre-designed questionnaire was used to collect the
primary data from the respondents (experiences). Data were collected
from one hundred and eighty seven respondents residing in and
around the Emirates of Sharjah and Dubai of the United Arab
Emirates. The collected data was analyzed with the help of statistical
tools such as averages, percentages, factor analysis, Student’s t-test
and Structural Equation Modelling Technique.
Objectives of the study are to know the reasons how married and
unmarried or single consumers of products and services are
motivated to use blogs as a source of information, to know whether
the consumers of products and services irrespective of their marital
status share their views and experiences with other bloggers and to
know the respondents’ future intentions towards blogging.
The study revealed the following: Majority of the respondents
have the motivation to blog because they are willing to receive
comments on what they post about services, convenience of blogs to
search for information about services and products, by blogging
respondents share information on the symptoms of a disease/ disorder
that may be experienced by someone, helps to share information
about ready to cook mix products and are keen to spend more time
blogging in the future.
Abstract: An extensive amount of work has been done in data
clustering research under the unsupervised learning technique in Data
Mining during the past two decades. Moreover, several approaches
and methods have been emerged focusing on clustering diverse data
types, features of cluster models and similarity rates of clusters.
However, none of the single clustering algorithm exemplifies its best
nature in extracting efficient clusters. Consequently, in order to
rectify this issue, a new challenging technique called Cluster
Ensemble method was bloomed. This new approach tends to be the
alternative method for the cluster analysis problem. The main
objective of the Cluster Ensemble is to aggregate the diverse
clustering solutions in such a way to attain accuracy and also to
improve the eminence the individual clustering algorithms. Due to
the massive and rapid development of new methods in the globe of
data mining, it is highly mandatory to scrutinize a vital analysis of
existing techniques and the future novelty. This paper shows the
comparative analysis of different cluster ensemble methods along
with their methodologies and salient features. Henceforth this
unambiguous analysis will be very useful for the society of clustering
experts and also helps in deciding the most appropriate one to resolve
the problem in hand.
Abstract: This work studied the ability of adipose tissue-derived
mesenchymal stromal cells (MSCs) to form stroma for expansion of
cord blood hematopoietic cells. We showed that 72-hour interaction
of MSCs with cord blood mononuclear cells (MNCs) in vitro at
atmospheric (20%) and low (5%) O2 conditions increased the
expression of ICAM-1, HCAM (at the beginning of interaction) on
MSCs. Viability of MSCs and MNCs were maintained at high level.
Adhesion of MNCs to MSCs was faster at 20% O2. MSCs promoted
the proliferation of adhered MNCs to form the suspension containing
great number of hematopoietic colony-forming units, and this effect
was more pronounced at 5% O2. Thus, adipose-derived MSCs
supplied sufficient stromal support to cord blood MNCs both at 20%
and 5% О2, providing their adhesion with further expansion of new
generation of different hematopoietic lineages.
Abstract: This paper presents development of the light-weight manipulator with series elastic actuation for medical telediagnostics (USG examination). General structure of realized impedance control algorithm was shown. It was described how to perform force measurements based mainly on elasticity of manipulator links.
Abstract: Turbulent flow in complex geometries receives considerable attention due to its importance in many engineering applications. It has been the subject of interest for many researchers. Some of these interests include the design of storm water channels. The design of these channels requires testing through physical models. The main practical limitation of physical models is the so called “scale effect”, that is, the fact that in many cases only primary physical mechanisms can be correctly represented, while secondary mechanisms are often distorted. These observations form the basis of our study, which centered on problems associated with the design of storm water channels near the Dead Sea, in Israel. To help reach a final design decision we used different physical models. Our research showed good coincidence with the results of laboratory tests and theoretical calculations, and allowed us to study different effects of fluid flow in an open channel. We determined that problems of this nature cannot be solved only by means of theoretical calculation and computer simulation. This study demonstrates the use of physical models to help resolve very complicated problems of fluid flow through baffles and similar structures. The study applies these models and observations to different construction and multiphase water flows, among them, those that include sand and stone particles, a significant attempt to bring to the testing laboratory a closer association with reality.
Abstract: The expanded Invasive Weed Optimization algorithm (exIWO) is an optimization metaheuristic modelled on the original IWO version created by the researchers from the University of Tehran. The authors of the present paper have extended the exIWO algorithm introducing a set of both deterministic and non-deterministic strategies of individuals’ selection. The goal of the project was to evaluate the exIWO by testing its usefulness for solving some test instances of the traveling salesman problem (TSP) taken from the TSPLIB collection which allows comparing the experimental results with optimal values.
Abstract: In this study, we will touch upon the legal arrangements issued in Turkey for prevention of condensation and for ensuring pluralism in the media. We will mention the legal arrangements concerning the regulatory and supervisory authority, namely the Radio and Television Supreme Council, for the visual and auditory media. In this context; the legal arrangements, which have been introduced by the Law No 6112 on the Establishment of Radio and Television Enterprises and Their Media Services in relation to the media ownership, will be reviewed through comparison with the Article 29 of the repealed Law No 3984.
Abstract: This paper deals with advanced state estimation algorithms for estimation of biomass concentration and specific growth rate in a typical fed-batch biotechnological process. This biotechnological process was represented by a nonlinear mass-balance based process model. Extended Kalman Filter (EKF) and Particle Filter (PF) was used to estimate the unmeasured state variables from oxygen uptake rate (OUR) and base consumption (BC) measurements. To obtain more general results, a simplified process model was involved in EKF and PF estimation algorithms. This model doesn’t require any special growth kinetic equations and could be applied for state estimation in various bioprocesses. The focus of this investigation was concentrated on the comparison of the estimation quality of the EKF and PF estimators by applying different measurement noises. The simulation results show that Particle Filter algorithm requires significantly more computation time for state estimation but gives lower estimation errors both for biomass concentration and specific growth rate. Also the tuning procedure for Particle Filter is simpler than for EKF. Consequently, Particle Filter should be preferred in real applications, especially for monitoring of industrial bioprocesses where the simplified implementation procedures are always desirable.
Abstract: An optimisation method using both global and local
optimisation is implemented to determine the flapping profile which
will produce the most lift for an experimental wing-actuation system.
The optimisation method is tested using a numerical quasi-steady
analysis. Results of an optimised flapping profile show a 20% increase
in lift generated as compared to flapping profiles obtained by high
speed cinematography of a Sympetrum frequens dragonfly. Initial
optimisation procedures showed 3166 objective function evaluations.
The global optimisation parameters - initial sample size and stage
one sample size, were altered to reduce the number of function
evaluations. Altering the stage one sample size had no significant
effect. It was found that reducing the initial sample size to 400
would allow a reduction in computational effort to approximately
1500 function evaluations without compromising the global solvers
ability to locate potential minima. To further reduce the optimisation
effort required, we increase the local solver’s convergence tolerance
criterion. An increase in the tolerance from 0.02N to 0.05N decreased
the number of function evaluations by another 20%. However, this
potentially reduces the maximum obtainable lift by up to 0.025N.
Abstract: In this paper, the design problem of state estimator for
neural networks with the mixed time-varying delays are investigated
by constructing appropriate Lyapunov-Krasovskii functionals and
using some effective mathematical techniques. In order to derive
several conditions to guarantee the estimation error systems to be
globally exponential stable, we transform the considered systems
into the neural-type time-delay systems. Then with a set of linear
inequalities(LMIs), we can obtain the stable criteria. Finally, three
numerical examples are given to show the effectiveness and less
conservatism of the proposed criterion.
Abstract: The society of 3rd Generation Partnership Project (3GPP) is completed developing Long Term Evolution Advanced (LTE-Advanced) systems as a standard 4G cellular system. This generation goals to produce conditions for a new radio-access technology geared to higher data rates, low latency, and better spectral efficiency. LTE-Advanced is an evolutionary step in the continuing development of LTE where the description in this article is based on LTE release 10. This paper provides a model of the traffic links of 4G system represented by LTE-Advanced system with the effect of the Transmission Control Protocols (TCP) and Stream Control Transmission Protocol (SCTP) in term of throughput and packet loss. Furthermore, the article presents the investigation and the analysis the behavior of SCTP and TCP variants over the 4G cellular systems. The traffic model and the scenario of the simulation developed using the network simulator NS-2 using different TCP source variants.
Abstract: Vertical slotted walls can be used as permeable
breakwaters to provide economical and environmental protection
from undesirable waves and currents inside the port. The permeable
breakwaters are partially protection and have been suggested to
overcome the environmental disadvantages of fully protection
breakwaters. For regular waves a semi-analytical model is based on
an eigenfunction expansion method and utilizes a boundary condition
at the surface of each wall are developed to detect the energy
dissipation through the slots. Extensive laboratory tests are carried
out to validate the semi-analytic models. The structure of the physical
model contains two walls and it consists of impermeable upper and
lower part, where the draft is based a decimal multiple of the total
depth. The middle part is permeable with a porosity of 50%. The
second barrier is located at a distant of 0.5, 1, 1.5 and 2 times of the
water depth from the first one. A comparison of the theoretical results
with previous studies and experimental measurements of the present
study show a good agreement and that, the semi-analytical model is
able to adequately reproduce most the important features of the
experiment.
Abstract: Advances in the field of image processing envision a
new era of evaluation techniques and application of procedures in
various different fields. One such field being considered is the
biomedical field for prognosis as well as diagnosis of diseases. This
plethora of methods though provides a wide range of options to select
from, it also proves confusion in selecting the apt process and also in
finding which one is more suitable. Our objective is to use a series of
techniques on bone scans, so as to detect the occurrence of
rheumatoid arthritis (RA) as accurately as possible. Amongst other
techniques existing in the field our proposed system tends to be more
effective as it depends on new methodologies that have been proved
to be better and more consistent than others. Computer aided
diagnosis will provide more accurate and infallible rate of
consistency that will help to improve the efficiency of the system.
The image first undergoes histogram smoothing and specification,
morphing operation, boundary detection by edge following algorithm
and finally image subtraction to determine the presence of
rheumatoid arthritis in a more efficient and effective way. Using preprocessing
noises are removed from images and using segmentation,
region of interest is found and Histogram smoothing is applied for a
specific portion of the images. Gray level co-occurrence matrix
(GLCM) features like Mean, Median, Energy, Correlation, Bone
Mineral Density (BMD) and etc. After finding all the features it
stores in the database. This dataset is trained with inflamed and noninflamed
values and with the help of neural network all the new
images are checked properly for their status and Rough set is
implemented for further reduction.
Abstract: The high efficiency power management IC (PMIC) with switching device is presented in this paper. PMIC is controlled with PFM control method in order to have high power efficiency at high current level. Dynamic Threshold voltage CMOS (DT-CMOS) with low on-resistance is designed to decrease conduction loss. The threshold voltage of DT-CMOS drops as the gate voltage increase, resulting in a much higher current handling capability than standard MOSFET. PFM control circuits consist of a generator, AND gate and comparator. The generator is made to have 1.2MHz oscillation voltage. The DC-DC converter based on PFM control circuit and low on-resistance switching device is presented in this paper.
Abstract: For Common R or R-L load to apply arbitrary voltage,
the bridge traditional inverters don’t have any difficulties by PWM
method. However for driving some piezoelectric actuator, arbitrary
voltage not a pulse but a steady voltage should be applied.
Piezoelectric load is considered as R-C load and its voltage does not
decrease even though the applied voltage decreases. Therefore it needs
some special inverter with circuit that can discharge the capacitive
energy. Especially for unidirectional arbitrary voltage driving like as
sine wave, it becomes more difficult problem. In this paper, a charge
and discharge circuit for unidirectional arbitrary voltage driving for
piezoelectric actuator is proposed. The circuit has charging and
discharging switches for increasing and decreasing output voltage.
With the proposed simple circuit, the load voltage can have any
unidirectional level with tens of bandwidth because the load voltage
can be adjusted by switching the charging and discharging switch
appropriately. The appropriateness is proved from the simulation of
the proposed circuit.
Abstract: In this study, a liquid phase microextraction by hollow fiber (HF-LPME) combined with high performance liquid chromatography-UV detector was applied to preconcentrate and determine trace levels of Cyproheptadine in human urine and plasma samples. Cyproheptadine was extracted from 10 mL alkaline aqueous solution (pH: 9.81) into an organic solvent (n-octnol) which was immobilized in the wall pores of a hollow fiber. Then was back-extracted into an acidified aqueous solution (pH: 2.59) located inside the lumen of the hollow fiber. This method is simple, efficient and cost-effective. It is based on pH gradient and differences between two aqueous phases. In order to optimize the HF-LPME some affecting parameters including the pH of donor and acceptor phases, the type of organic solvent, ionic strength, stirring rate, extraction time and temperature were studied and optimized. Under optimal conditions enrichment factor, limit of detection (LOD) and relative standard deviation (RSD(%), n=3) were up to 112, 15 μg.L−1 and 2.7, respectively.
Abstract: This research aimed to study on the efficiency of wastewater treatment by comparing the different aeration times of surface aerators in Suan Sunandha Rajabhat University. In doing so, the operation of surface aerators was divided into 2 groups which included the groups of 8 hours (8-0/opened-closed) and 4 hours (2-2/opened-closed) of aeration time per day. As a result of the study, it was found that the efficiency of wastewater treatment in the forms of DO, BOD, turbidity and NO2- by 8 hours (8-0/opened-closed) and 4 hours (2-2/opened-closed) of aeration time per day of surface aerators was not statistically different [Sig. = .644, .488, .716 and .054 > α (.05)] while the efficiency in the forms of NO3- and P was significantly different at the statistical level of .01 [Sig. = .001 and .000 < α (.01)].