Abstract: Despite of many scholars and practitioners recognize
the knowledge management implementation in an organizations but
insufficient attention has been paid by researchers to select suitable
knowledge portal system (KPS) selection. This study develops a
Multi Criteria Decision making model based on the fuzzy VIKOR
approach to help organizations in selecting KPS. The suitable portal
is the critical influential factors on the success of knowledge
management (KM) implementation in an organization.
Abstract: Catalytic converters are used for minimizing the release of pollutants to the atmosphere. It is during the warm-up period that hydrocarbons are seen to be released in appreciable quantities from these converters. In this paper the conversion of a fast oxidizing hydrocarbon propylene is analysed using two numerical methods. The quasi steady state method assumes the accumulation terms to be negligible in the gas phase mass and energy balance equations, however this term is present in the solid phase energy balance. The unsteady state model accounts for the accumulation term to be present in the gas phase mass and energy balance and in the solid phase energy balance. The results derived from the two models for gas concentration, gas temperature and solid temperature are compared.
Abstract: Dredged sediment (DS) was utilized as source of
silt-clay and organic matter in artificially prepared eelgrass substrates with mountain sand (MS) as the sand media. Addition of DS showed
improved growth of eelgrass in the mixed substrates. Increase in added
DS up to 15% silt-clay showed increased shoot growth but additional
DS in 20% silt-clay mixture didn-t result to further increase in eelgrass
growth. Improved root establishment were also found for plants in pots
with added DS as shown by the increased resistance to uprooting, increased number of rhizome nodes and longer roots. Results demonstrated that addition of DS may be beneficial to eelgrass up to a
certain extent only and too much of it might be harmful to eelgrass plants.
Abstract: The main objective of this paper is to analyse the influence of preparation and control of orders on performance. The focused activities explored in this research are: procurement, production and distribution. These changes in performance were obtained through improvement of the supply chain. It is proved using all the company activities that it is possible to increase de efficiency and do services in an adequate way, placing the products in the market efficiently. For that, it was explored the importance of the supply chain, with privilege to the practical environment and the quantification of the obtained results.
Abstract: The thermal, epithermal and fast fluxes were
calculated for three irradiation channels at Egypt Second Research
Reactor (ETRR-2) using CITVAP code. The validity of the
calculations was verified by experimental measurements. There are
some deviations between measurements and calculations. This is due
to approximations in the calculation models used, homogenization of
regions, condensation of energy groups and uncertainty in nuclear
data used. Neutron flux data for the three irradiation channels are
now available. This would enable predicting the irradiation
conditions needed for future radioisotope production.
Abstract: Sedimentation is a hydraulic phenomenon that is
emerging as a serious challenge in river engineering. When the flow
reaches a certain state that gather potential energy, it shifts the
sediment load along channel bed. The transport of such materials can
be in the form of suspended and bed loads. The movement of these
along the river course and channels and the ways in which this could
influence the water intakes is considered as the major challenges for
sustainable O&M of hydraulic structures. This could be very serious
in arid and semi-arid regions like Iran, where inappropriate watershed
management could lead to shifting a great deal of sediments into the
reservoirs and irrigation systems. This paper aims to investigate
sedimentation in the Western Canal of Dez Diversion Weir in Iran,
identifying factors which influence the process and provide ways in
which to mitigate its detrimental effects by using the SHARC
Software.
For the purpose of this paper, data from the Dezful water authority
and Dezful Hydrometric Station pertinent to a river course of about 6
Km were used.
Results estimated sand and silt bed loads concentrations to be 193
ppm and 827ppm respectively. Given the available data on average
annual bed loads and average suspended sediment loads of 165ppm
and 837ppm, there was a significant statistical difference (16%)
between the sand grains, whereas no significant difference (1.2%)
was find in the silt grain sizes. One explanation for such finding
being that along the 6 Km river course there was considerable
meandering effects which explains recent shift in the hydraulic
behavior along the stream course under investigation. The sand
concentration in downstream relative to present state of the canal
showed a steep descending curve. Sediment trapping on the other
hand indicated a steep ascending curve. These occurred because the
diversion weir was not considered in the simulation model.
Abstract: Buildings and associated construction methods have a significant impact on the environment. As construction activity increases in Kuwait, there is a need to create design and construction strategies which will minimize the environmental impact of new buildings. Green construction is a design philosophy intended to improve the sustainability of construction by the minimization of resource depletion and CO2 emissions throughout the life cycle of buildings. This paper presents and discusses the results of a survey that was conducted in Kuwait, with the objective of investigating the awareness of developers and other stakeholders regarding their understanding and use of green construction strategies. The results of the survey demonstrate that whilst there seems to be a reasonable level of awareness amongst the stakeholders, this awareness is not currently well reflected in the design and construction practices actually being applied. It is therefore concluded is there is a pressing need for intervention from Government in order that the use of sustainable green design and construction strategies becomes the norm in Kuwait.
Abstract: This paper presents a methodology for operational and
economic characteristics based evaluation and selection of a power
plant using Graph theoretic approach. A universal evaluation index
on the basis of Operational and economics characteristics of a plant is
proposed which evaluates and ranks the various types of power plants.
The index thus obtained from the pool of operational characteristics
of the power plant attributes Digraph. The Digraph is developed
considering Operational and economics attributes of the power plants
and their relative importance for their smooth operation, installation
and commissioning and prioritizing their selection. The sensitivity
analysis of the attributes towards the objective has also been carried
out in order to study the impact of attributes over the desired outcome
i.e. the universal operational-economics index of the power plant.
Abstract: The hydraulic actuated excavator, being a non-linear
mobile machine, encounters many uncertainties. There are
uncertainties in the hydraulic system in addition to the uncertain
nature of the load. The simulation results obtained in this study show
that there is a need for intelligent control of such machines and in
particular interval type-2 fuzzy controller is most suitable for
minimizing the position error of a typical excavator-s bucket under
load variations. We consider the model parameter uncertainties such
as hydraulic fluid leakage and friction. These are uncertainties which
also depend up on the temperature and alter bulk modulus and
viscosity of the hydraulic fluid. Such uncertainties together with the
load variations cause chattering of the bucket position. The interval
type-2 fuzzy controller effectively eliminates the chattering and
manages to control the end-effecter (bucket) position with positional
error in the order of few millimeters.
Abstract: This Paper proposes a new facial feature extraction approach, Wash-Hadamard Transform (WHT). This approach is based on correlation between local pixels of the face image. Its primary advantage is the simplicity of its computation. The paper compares the proposed approach, WHT, which was traditionally used in data compression with two other known approaches: the Principal Component Analysis (PCA) and the Discrete Cosine Transform (DCT) using the face database of Olivetti Research Laboratory (ORL). In spite of its simple computation, the proposed algorithm (WHT) gave very close results to those obtained by the PCA and DCT. This paper initiates the research into WHT and the family of frequency transforms and examines their suitability for feature extraction in face recognition applications.
Abstract: Most of the commercial gluten free products are
nutritionally inferior when compared to gluten containing
counterparts as manufacturers most often use the refined flours and
starches. So it is possible that people on gluten free diet have low
intake of fibre content. The foxtail millet flour and copra meal are
gluten free and have high fibre and protein contents. The formulation
of fibre rich gluten free cookies was optimized by response surface
methodology considering independent process variables as proportion
of Foxtail millet (Setaria italica) flour in mixed flour, fat content and
guar gum. The sugar, sodium chloride, sodium bicarbonates and
water were added in fixed proportion as 60, 1.0, 0.4 and 20% of
mixed flour weight, respectively. Optimum formulation obtained for
maximum spread ratio, fibre content, surface L-value, overall
acceptability and minimum breaking strength were 80% foxtail millet
flour in mixed flour, 42.8 % fat content and 0.05% guar gum.
Abstract: Series compensators have been used for many years,
to increase the stability and load ability of transmission line. They
compensate retarded or advanced volt drop of transmission lines
by placing advanced or retarded voltage in series with them to
compensate the effective reactance, which cause to increase load
ability of transmission lines. In this paper, two method of fuzzy
controller, based on power reference tracking and impedance
reference tracking have been developed on TCSC controller in
order to increase load ability and improving power oscillation
damping of system. In these methods, fire angle of thyristors are
determined directly through the special Rule-bases with the error
and change of error as the inputs. The simulation results of two
area four- machines power system show the good performance of
power oscillation damping in system. Comparison of this method
with classical PI controller shows the increasing speed of system
response in power oscillation damping.
Abstract: Component handling system is one of the important sub systems of Prototype Fast Breeder Reactor (PFBR) used for fuel handling. Core handling system is again a sub system of component handling system. Core handling system consists of in-vessel and ex-vessel subassembly handling. In-vessel core handling involves transfer arm, large rotatable plug and small rotatable plug operations. Modeling and simulation of in-vessel core handling is a part of development of Prototype Fast Breeder Reactor Operator Training Simulator. This paper deals with simulation and modeling of operations of transfer arm, large rotatable plug and small rotatable plug needed for in-vessel core handling. Process modeling was developed in house using platform independent Cµ code with OpenGL (Open Graphics Library). The control logic models and virtual panel were modeled using simulation tool.
Abstract: The aim of the work was to attenuate the vibration amplitude in CESNA 172 airplane wing by using Functionally Graded Material instead of uniform or composite material. Wing strength was achieved by means of stress analysis study, while wing vibration amplitudes and shapes were achieved by means of Modal and Harmonic analysis. Results were verified by applying the methodology in a simple cantilever plate to the simple model and the results were promising and the same methodology can be applied to the airplane wing model. Aluminum models, Titanium models, and functionally graded materials of Aluminum and titanium results were compared to show a great vibration attenuation after using the FGM. Optimization in FGM gradation satisfied our objective of reducing and attenuating the vibration amplitudes to show the effect of using FGM in vibration behavior. Testing the Aluminum rich models, and comparing it with the titanium rich model was an optimization in this paper. Results have shown a significant attenuation in vibration magnitudes when using FGM instead of Titanium Plate, and Aluminium wing with FGM Spurs instead of Aluminium wings. It was also recommended that in future, changing the graphical scale to 1:10 or even 1:1 when the computers- capabilities allow.
Abstract: Steel made pipelines with different diameters are used
for transmitting oil and gas which in many cases are buried in soil
under the sea bed or immersed in sea water. External corrosion of
pipes is an important form of deterioration due to the aggressive
environment of sea water. Corrosion normally results in pits. Hence,
using the finite element method, namely ABAQUS software, this
paper estimates the amount of pressure capacity reduction of a pipecontaining
a semi-elliptical pitting corrosion and the rate of corrosion
during the pipeline life of 25 years.
Abstract: e-mail has become an important means of electronic
communication but the viability of its usage is marred by Unsolicited
Bulk e-mail (UBE) messages. UBE consists of many types
like pornographic, virus infected and 'cry-for-help' messages as well
as fake and fraudulent offers for jobs, winnings and medicines. UBE
poses technical and socio-economic challenges to usage of e-mails.
To meet this challenge and combat this menace, we need to
understand UBE. Towards this end, the current paper presents a
content-based textual analysis of nearly 3000 winnings-announcing
UBE. Technically, this is an application of Text Parsing and
Tokenization for an un-structured textual document and we approach
it using Bag Of Words (BOW) and Vector Space Document Model
techniques. We have attempted to identify the most frequently
occurring lexis in the winnings-announcing UBE documents. The
analysis of such top 100 lexis is also presented. We exhibit the
relationship between occurrence of a word from the identified lexisset
in the given UBE and the probability that the given UBE will be
the one announcing fake winnings. To the best of our knowledge and
survey of related literature, this is the first formal attempt for
identification of most frequently occurring lexis in winningsannouncing
UBE by its textual analysis. Finally, this is a sincere
attempt to bring about alertness against and mitigate the threat of
such luring but fake UBE.
Abstract: An experiment was conducted using two aeration
methods (water-into-air and air-into-water) and followed by filtration
processes using manganese greensand material. The properties of
groundwater such as pH, dissolved oxygen, turbidity and heavy metal
concentration (iron and manganese) will be assessed. The objectives
of this study are i) to determine the effective aeration method and ii)
to assess the effectiveness of manganese greensand as filter media in
removing iron and manganese concentration in groundwater. Results
showed that final pH for all samples after treatment are in range from
7.40 and 8.40. Both aeration methods increased the dissolved oxygen
content. Final turbidity for groundwater samples are between 3 NTU
to 29 NTU. Only three out of eight samples achieved iron
concentration of 0.3mg/L and less and all samples reach manganese
concentration of 0.1mg/L and less. Air-into-water aeration method
gives higher percentage of iron and manganese removal compare to
water-into-air method.
Abstract: An attempt was made for availability of wastewater reuse/reclamation for irrigation purposes using phytoremediation “the low cost and less technology", using six local aquatic macrophytes “e.g. T. angustifolia, B. maritimus, Ph. australis, A. donax, A. plantago-aquatica and M. longifolia (Linn)" as biological waste purifiers. Outdoor experiments/designs were conducted from May 03, 2007 till October 15, 2008, close to one of the main sewage channels of Sulaimani City/Iraq*. All processes were mainly based on conventional wastewater treatment processes, besides two further modifications were tested, the first was sand filtration pots, implanted by individual species of experimental macrophytes and the second was constructed wetlands implanted by experimental macrophytes all together. Untreated and treated wastewater samples were analyzed for their key physico-chemical properties (only heavy metals Fe, Mn, Zn and Cu with particular reference to removal efficiency by experimental macrophytes are highlighted in this paper). On the other hand, vertical contents of heavy metals were also evaluated from both pots and the cells of constructed wetland. After 135 days, macrophytes were harvested and heavy metals were analyzed in their biomass (roots/shoots) for removal efficiency assessment (i.e. uptake/ bioaccumulation rate). Results showed that; removal efficiency of all studied heavy metals was much higher in T. angustifolia followed by Ph. Australis, B. maritimus and A. donax in triple experiment sand pots. Constructed wetland experiments have revealed that; the more replicated constructed wetland cells the highest heavy metal removal efficiency was indicated.
Abstract: Numerical studies have been carried out using a
validated two-dimensional RNG k-epsilon turbulence model for the
design optimization of a thrust vector control system using shock
induced supersonic secondary jet. Parametric analytical studies have
been carried out with various secondary jets at different divergent
locations, jet interaction angles, jet pressures. The results from the
parametric studies of the case on hand reveal that the primary nozzle
with a small divergence angle, downstream injections with a distance
of 2.5 times the primary nozzle throat diameter from the primary
nozzle throat location warrant higher efficiency over a certain range
of jet pressures and jet angles. We observed that the supersonic
secondary jet opposing the core flow with jets interaction angle of
40o to the axis far downstream of the nozzle throat facilitates better
thrust vectoring than the secondary jet with same direction as that of
core flow with various interaction angles. We concluded that fixing
of the supersonic secondary jet nozzle pointing towards the throat
direction with suitable angle at a distance 2 to 4 times of the primary
nozzle throat diameter, as the case may be, from the primary nozzle
throat location could facilitate better thrust vectoring for the
supersonic aerospace vehicles.
Abstract: A new generation product made from bamboo strips,
known as laminated bamboo, has gained importance. The objective
of this research was to experiment the effect of three factors on the
mechanical property of laminated bamboo. The interested factors for
experimental design were (A) four bamboo species, namely Bambusa
blumeana Schultes (Pai See Suk), Dendrocalamus asper Backer (Pai
Tong), Dendrocalamus hamiltonii Nees (Pai Hok) and
Dendrocalamus sericeus Munro (Pai Sang Mon), (B) two types of
glue adhesive, polyvinyl acetate emulsion (PVAC) fortified with
urea-formaldehyde (UF) and urea-formaldehyde (UF) to make
parallel-oriented bamboo strips laminates and (C) glue weight per
strip area, 150 g/m2 and 190 g/m2. Experimental results showed that
Dendrocalamus asper Backer (Pai Tong) and Dendrocalamus
sericeus Munro (Pai Sang Mon) were best used for manufacturing
due to their highest MOR and MOE. The amount of glue weight 150
g/m2 yielded higher MOR and MOE than the amount of glue weight
190 g/m2. At the conclusion, the laminated bamboo manufacturers
can benefit from this research in order to select right materials
according to strength, cost and accessibility.