Abstract: Banana is one of the most consumed fruits in the tropics and subtropics. Brazil accounts for about 9% of the world banana production. However, the production losses are as high as 30 to 40% and even much higher in some developing countries. The green banana flour is a complex carbohydrate source, including a high total starch (73.4%), resistant starch (17.5%) with functional properties. Gamma irradiation is considered to be an alternative method for food preservation. It has been performed due to the need of extending the shelf - life of foods, whilst maintaining their safety and avoiding one of the main concerns: the nutrient loss. In this work data about on the effects of ionizing radiation on the physicochemical analysis (carbohydrate, proteins, lipids, alimentary fiber, moistures and ashes) of Brazilian functional products (biscuits and bread) of the green banana pulp are presented. The caloric value was calculated. No significant difference was observed between the samples of irradiated and non – irradiated green banana biscuits with the following determinations: carbohydrates, proteins, alimentary fiber and ashes. Only a small significant difference was found in lipids (macronutrients). The results of physical chemical analysis of the irradiated and non- irradiated green banana bread non- irradiated showed no significant difference with the following determinations: carbohydrates, lipids (macronutrients), moisture, ashes and caloric value. A small difference was found in proteins (macronutrients). Irradiation of functional products (biscuits and bread) with doses of 1 and 3kGy maintained their original macronutrients content, showing good radioresistance.
Abstract: It was determined that woody biomass and livestock excreta can be utilized as hydrogen resources and hydrogen produced from such sources can be used to fill fuel cell vehicles (FCVs) at hydrogen stations. It was shown that the biomass transport costs for hydrogen production may be reduced the costs for co-generation. In the Tokyo Metropolitan Area, there are only a few sites capable of producing hydrogen from woody biomass in amounts greater than 200 m3/h-the scale required for a hydrogen station to be operationally practical. However, in the case of livestock excreta, it was shown that 15% of the municipalities in this area are capable of securing sufficient biomass to be operationally practical for hydrogen production. The differences in feasibility of practical operation depend on the type of biomass.
Abstract: In this research, an anaerobic co-digestion using decanter cake from palm oil mill industry to improve the biogas production from frozen seafood wastewater is studied using Continuously Stirred Tank Reactor (CSTR) process. The experiments were conducted in laboratory-scale. The suitable Hydraulic Retention Time (HRT) was observed in CSTR experiments with 24 hours of mixing time using the mechanical mixer. The HRT of CSTR process impacts on the efficiency of biogas production. The best performance for biogas production using CSTR process was the anaerobic codigestion for 20 days of HRT with the maximum methane production rate of 1.86 l/d and the average maximum methane production of 64.6%. The result can be concluded that the decanter cake can improve biogas productivity of frozen seafood wastewater.
Abstract: Advances in technology (e.g. the internet,
telecommunication) and political changes (fewer trade barriers and an
enlarged European Union, ASEAN, NAFTA and other organizations)
have led to develop international competition and expand into new
markets. Companies in Thailand, Asia and around the globe are
increasingly being pressured on price and for faster time to enter the
market. At the same time, new markets are appearing and many
companies are looking for changes and shifts in their domestic
markets. These factors have enabled the rapid growth for companies
and globalizing many different business activities during the product
development process from research and development (R&D) to
production.
This research will show and clarify methods how to develop
global product. Also, it will show how important is a global product
impact into Thai Economy development.
Abstract: The present study addresses problems and solutions
related to new functional food production. Wheat (Triticum aestivum
L) bran obtained from industrial mill company “Dobeles
dzirnavieks”, was used to investigate them as raw material like
nutrients for Bifidobacterium lactis Bb-12. Enzymatic hydrolysis of
wheat bran starch was carried out by α-amylase from Bacillus
amyloliquefaciens (Sigma Aldrich). The Viscozyme L purchased
from (Sigma Aldrich) were used for reducing released sugar.
Bifidibacterium lactis Bb-12 purchased from (Probio-Tec® CHR
Hansen) was cultivated in enzymatically hydrolysed wheat bran
mash. All procedures ensured the number of active Bifidobacterium
lactis Bb-12 in the final product reached 105 CFUg-1. After enzymatic
and bacterial fermentations sample were freeze dried for analysis of
chemical compounds. All experiments were performed at Faculty of
Food Technology of Latvia University of Agriculture in January-
March 2013. The obtained results show that both types of wheat bran
(enzymatically treated and non-treated) influenced the fermentative
activity and number of Bifidibacterium lactis Bb-12 viable in wheat
bran mash. Amount of acidity strongly increase during the wheat
bran mash fermentation. The main objective of this work was to
create low-energy functional enzymatically and bacterially treated
food from wheat bran using enzymatic hydrolysis of carbohydrates
and following cultivation of Bifidobacterium lactis Bb-12.
Abstract: In this paper, naturally immobilized lipase, Carica
papaya lipase, catalyzed biodiesel production from fish oil was
studied. The refined fish oil, extracted from the discarded parts of
fish, was used as a starting material for biodiesel production. The
effects of molar ratio of oil: methanol, lipase dosage, initial water
activity of lipase, temperature and solvent were investigated. It was
found that Carica papaya lipase was suitable for methanolysis of fish
oil to produce methyl ester. The maximum yield of methyl ester
could reach up to 83% with the optimal reaction conditions: oil:
methanol molar ratio of 1: 4, 20% (based on oil) of lipase, initial
water activity of lipase at 0.23 and 20% (based on oil) of tert-butanol
at 40oC after 18 h of reaction time. There was negligible loss in
lipase activity even after repeated use for 30 cycles.
Abstract: The photochemical and photo-Fenton oxidation of 1,3-dichloro-2-propanol was performed in a batch reactor, at room temperature, using UV radiation, H2O2 as oxidant, and Fenton-s reagent. The effect of the oxidative agent-s initial concentration was investigated as well as the effect of the initial concentration of Fe(II) by following the target compound degradation, the total organic carbon removal and the chloride ion production. Also, from the kinetic analysis conducted and proposed reaction scheme it was deduced that the addition of Fe(II) significantly increases the production and the further oxidation of the chlorinated intermediates.
Abstract: The manufacture of large-scale precision aerospace
components using CNC requires a highly effective maintenance
strategy to ensure that the required accuracy can be achieved over
many hours of production. This paper reviews a strategy for a
maintenance management system based on Failure Mode Avoidance,
which uses advanced techniques and technologies to underpin a
predictive maintenance strategy. It is shown how condition
monitoring (CM) is important to predict potential failures in high
precision machining facilities and achieve intelligent and integrated
maintenance management. There are two distinct ways in which CM
can be applied. One is to monitor key process parameters and
observe trends which may indicate a gradual deterioration of
accuracy in the product. The other is the use of CM techniques to
monitor high status machine parameters enables trends to be
observed which can be corrected before machine failure and
downtime occurs.
It is concluded that the key to developing a flexible and intelligent
maintenance framework in any precision manufacturing operation is
the ability to evaluate reliably and routinely machine tool condition
using condition monitoring techniques within a framework of Failure
Mode Avoidance.
Abstract: In this research, CaO-ZnO catalysts (with various
Ca:Zn atomic ratios of 1:5, 1:3, 1:1, and 3:1) prepared by incipientwetness
impregnation (IWI) and co-precipitation (CP) methods were
used as a catalyst in the transesterification of palm oil with methanol
for biodiesel production. The catalysts were characterized by several
techniques, including BET method, CO2-TPD, and Hemmett
Indicator. The effects of precursor concentration, and calcination
temperature on the catalytic performance were studied under reaction
conditions of a 15:1 methanol to oil molar ratio, 6 wt% catalyst,
reaction temperature of 60°C, and reaction time of 8 h. At Ca:Zn
atomic ratio of 1:3 gave the highest FAME value owing to a basic
properties and surface area of the prepared catalyst.
Abstract: Article devoted to the development of technologies
for medicine and agroecology by using plant organelle – spherosome.
Technological method of purification and isolation of this organelle
by using novel nanostructured carbon sorbent – “nanocarbosorb"
ARK type are presented. Also the methods of preparation of
nanocontainers based on using of spherosome with loaded isosorbide
dinitrate, piroxicam or diclofenak are exhibited. We found that the
spherosome could be applied for ecological aims as bioregulator and
also as biosensor for determination of ammonia ions in water
reservoirs at concentration range 1mM to 100mM.
Abstract: Food and fibre production in arid and semi-arid regions has emerged as one of the major challenges for various socio-economic and political reasons such as the food security and self-sufficiency. Productive use of the renewable water resources has risen on top ofthe decision-making agenda. For this reason, efficient operation and maintenance of modern irrigation and drainage schemes become part and parcel and indispensible reality in agricultural policy making arena. The aim of this paper is to investigate the complexity of operating and maintaining such schemes, mainly focussing on challenges which enhance and opportunities that impedsustainable food and fibre production. The methodology involved using secondary data complemented byroutine observations and stakeholders views on issues that influence the O&M in the Dez command area. The SPSS program was used as an analytical framework for data analysis and interpretation.Results indicate poor application efficiency in most croplands, much of which is attributed to deficient operation of conveyance and distribution canals. These in turn, are reportedly linked to inadequate maintenance of the pumping stations and hydraulic structures like turnouts,flumes and other control systems particularly in the secondary and tertiary canals. Results show that the aforementioned deficiencies have been the major impediment to establishing regular flow toward the farm gates which subsequently undermine application efficiency and tillage operationsat farm level. Results further show that accumulative impact of such deficiencies has been the major causes of poorcrop yield and quality that deem production system in these croplands uneconomic. Results further show that the present state might undermine the sustainability of agricultural system in the command area. The overall conclusion being that present water management is unlikely to be responsive to challenges that the sector faces. And in the absence of coherent measures to shift the status quo situation in favour of more productive resource use, it would be hard to fulfil the objectives of the National Economic and Socio-cultural Development Plans.
Abstract: Due to the fact that in the new century customers tend
to express globally increasing demands, networks of interconnected
businesses have been established in societies and the management of
such networks seems to be a major key through gaining competitive
advantages. Supply chain management encompasses such managerial
activities. Within a supply chain, a critical role is played by quality.
QFD is a widely-utilized tool which serves the purpose of not only
bringing quality to the ultimate provision of products or service
packages required by the end customer or the retailer, but it can also
initiate us into a satisfactory relationship with our initial customer;
that is the wholesaler. However, the wholesalers- cooperation is
considerably based on the capabilities that are heavily dependent on
their locations and existing circumstances. Therefore, it is undeniable
that for all companies each wholesaler possesses a specific
importance ratio which can heavily influence the figures calculated in
the House of Quality in QFD. Moreover, due to the competitiveness
of the marketplace today, it-s been widely recognized that
consumers- expression of demands has been highly volatile in
periods of production. Apparently, such instability and proneness to
change has been very tangibly noticed and taking it into account
during the analysis of HOQ is widely influential and doubtlessly
required. For a more reliable outcome in such matters, this article
demonstrates the application viability of Analytic Network Process
for considering the wholesalers- reputation and simultaneously
introduces a mortality coefficient for the reliability and stability of
the consumers- expressed demands in course of time. Following to
this, the paper provides further elaboration on the relevant
contributory factors and approaches through the calculation of such
coefficients. In the end, the article concludes that an empirical
application is needed to achieve broader validity.
Abstract: Rice husk is a lignocellulosic source that can be
converted to ethanol. Three hundreds grams of rice husk was mixed
with 1 L of 0.18 N sulfuric acid solutions then was heated in an
autoclave. The reaction was expected to be at constant temperature
(isothermal), but before that temperature was achieved, reaction has
occurred. The first liquid sample was taken at temperature of 140 0C
and repeated every 5 minute interval. So the data obtained are in the
regions of non-isothermal and isothermal. It was observed that the
degradation has significant effects on the ethanol production. The
kinetic constants can be expressed by Arrhenius equation with the
frequency factors for hydrolysis and sugar degradation of 1.58 x 105
min-1 and 2.29 x 108 L/mole-min, respectively, while the activation
energies are 64,350 J/mole and 76,571 J/mole. The highest ethanol
concentration from fermentation is 1.13% v/v, attained at 220 0C.
Abstract: Frequent machine breakdowns, low plant availability and increased overtime are a great threat to a manufacturing plant as they increase operating costs of an industry. The main aim of this study was to improve Overall Equipment Effectiveness (OEE) at a manufacturing company through the implementation of innovative maintenance strategies. A case study approach was used. The paper focuses on improving the maintenance in a manufacturing set up using an innovative maintenance regime mix to improve overall equipment effectiveness. Interviews, reviewing documentation and historical records, direct and participatory observation were used as data collection methods during the research. Usually production is based on the total kilowatt of motors produced per day. The target kilowatt at 91% availability is 75 Kilowatts a day. Reduced demand and lack of raw materials particularly imported items are adversely affecting the manufacturing operations. The company had to reset its targets from the usual figure of 250 Kilowatt per day to mere 75 per day due to lower availability of machines as result of breakdowns as well as lack of raw materials. The price reductions and uncertainties as well as general machine breakdowns further lowered production. Some recommendations were given. For instance, employee empowerment in the company will enhance responsibility and authority to improve and totally eliminate the six big losses. If the maintenance department is to realise its proper function in a progressive, innovative industrial society, then its personnel must be continuously trained to meet current needs as well as future requirements. To make the maintenance planning system effective, it is essential to keep track of all the corrective maintenance jobs and preventive maintenance inspections. For large processing plants these cannot be handled manually. It was therefore recommended that the company implement (Computerised Maintenance Management System) CMMS.
Abstract: Drilling is the most common machining operation and it forms the highest machining cost in many manufacturing activities including automotive engine production. The outcome of this operation depends upon many factors including utilization of proper cutting tool geometry, cutting tool material and the type of coating used to improve hardness and resistance to wear, and also cutting parameters. With the availability of a large array of tool geometries, materials and coatings, is has become a challenging task to select the best tool and cutting parameters that would result in the lowest machining cost or highest profit rate. This paper describes an algorithm developed to help achieve good performances in drilling operations by automatically determination of proper cutting tools and cutting parameters. It also helps determine machining sequences resulting in minimum tool changes that would eventually reduce machining time and cost where multiple tools are used.
Abstract: Improvement in CAE methods has an important role for shortening of the vehicle product development time. It is provided that validation of the design and improvements in terms of durability can be done without hardware prototype production. In recent years, several different methods have been developed in order to investigate fatigue damage of the vehicle. The intended goal among these methods is prediction of fatigue damage in a short time with reduced costs. This study developed a new fatigue damage prediction method in the automotive sector using power spectrum densities of accelerations. This study also confirmed that the weak region in vehicle can be easily detected with the method developed in this study which results were compared with conventional method.
Abstract: Recently the use of data mining to scientific bibliographic data bases has been implemented to analyze the pathways of the knowledge or the core scientific relevances of a laureated novel or a country. This specific case of data mining has been named citation mining, and it is the integration of citation bibliometrics and text mining. In this paper we present an improved WEB implementation of statistical physics algorithms to perform the text mining component of citation mining. In particular we use an entropic like distance between the compression of text as an indicator of the similarity between them. Finally, we have included the recently proposed index h to characterize the scientific production. We have used this web implementation to identify users, applications and impact of the Mexican scientific institutions located in the State of Morelos.
Abstract: The aim of the study was to evaluate the effect of
texturizers on the rheological properties of the apple mass and
desserts made from various raw materials. The apple varieties -
‘Antonovka’, ‘Baltais Dzidrais’, and ‘Zarja Alatau’ harvested in
Latvia, were used for the experiment. The apples were processed in a
blender unpeeled for obtaining a homogenous mass. The apple mass
was analyzed fresh and after storage at –18ºC. Both fresh and thawed
apple mass samples with added gelatin, xantan gum, and sodium
carboxymethylcellulose were whisked obtaining dessert. Pectin, pH
and soluble dry matter of the product were determined. Apparent
viscosity was measured using a rotational viscometer DV–III Ultra.
Pectin content in frozen apple mass decreased significantly (p
Abstract: The paper outlines the relevance of computational
geometry within the design and production process of architecture.
Based on two case studies, the digital chain - from the initial formfinding
to the final realization of spatial concepts - is discussed in
relation to geometric principles. The association with the fascinating
complexity that can be found in nature and its underlying geometry
was the starting point for both projects presented in the paper. The
translation of abstract geometric principles into a three-dimensional
digital design model – realized in Rhinoceros – was followed by a
process of transformation and optimization of the initial shape that
integrated aesthetic, spatial and structural qualities as well as aspects
of material properties and conditions of production.
Abstract: Perth will run out of available sustainable natural
water resources by 2015 if nothing is done to slow usage rates,
according to a Western Australian study [1]. Alternative water
technology options need to be considered for the long-term
guaranteed supply of water for agricultural, commercial, domestic
and industrial purposes. Seawater is an alternative source of water for
human consumption, because seawater can be desalinated and
supplied in large quantities to a very high quality.
While seawater desalination is a promising option, the technology
requires a large amount of energy which is typically generated from
fossil fuels. The combustion of fossil fuels emits greenhouse gases
(GHG) and, is implicated in climate change. In addition to
environmental emissions from electricity generation for desalination,
greenhouse gases are emitted in the production of chemicals and
membranes for water treatment. Since Australia is a signatory to the
Kyoto Protocol, it is important to quantify greenhouse gas emissions
from desalinated water production.
A life cycle assessment (LCA) has been carried out to determine
the greenhouse gas emissions from the production of 1 gigalitre (GL)
of water from the new plant. In this LCA analysis, a new desalination
plant that will be installed in Bunbury, Western Australia, and known
as Southern Seawater Desalinization Plant (SSDP), was taken as a
case study. The system boundary of the LCA mainly consists of three
stages: seawater extraction, treatment and delivery. The analysis
found that the equivalent of 3,890 tonnes of CO2 could be emitted
from the production of 1 GL of desalinated water. This LCA analysis
has also identified that the reverse osmosis process would cause the
most significant greenhouse emissions as a result of the electricity
used if this is generated from fossil fuels