Abstract: The paper presents a space-vector pulse width modulation (SVPWM) inverter feeding a permanent-magnet synchronous motor (PMSM). The SVPWM inverter enables to feed the motor with a higher voltage with low harmonic distortions than the conventional sinusoidal PWM inverter. The control strategy of the inverter is the voltage / frequency control method, which is based on the space-vector modulation technique. The proposed PMSM drive system involving the field-oriented control scheme not only decouples the torque and flux which provides faster response but also makes the control task easy. The performance of the proposed drive is simulated. The advantages of the proposed drive are confirmed by the simulation results.
Abstract: In this paper, three types of defected ground structure
(DGS) units which are triangular-head (TH), rectangular-head (RH)
and U-shape (US) are investigated. They are further used to low-pass
and band-pass filters designs (LPF and BPF) and the obtained
performances are examined. The LPF employing RH-DGS geometry
presents the advantages of compact size, low-insertion loss and wide
stopband compared to the other filters. It provides cutoff frequency of
2.5 GHz, largest rejection band width of 20 dB from 2.98 to 8.76
GHz, smallest transition region and smallest sharpness of the cutoff
frequency. The BPF based on RH-DGS has the highest bandwidth
(BW) of about 0.74 GHz and the lowest center frequency of 3.24
GHz, whereas the other BPFs have BWs less than 0.7 GHz.
Abstract: Image compression plays a vital role in today-s
communication. The limitation in allocated bandwidth leads to
slower communication. To exchange the rate of transmission in the
limited bandwidth the Image data must be compressed before
transmission. Basically there are two types of compressions, 1)
LOSSY compression and 2) LOSSLESS compression. Lossy
compression though gives more compression compared to lossless
compression; the accuracy in retrievation is less in case of lossy
compression as compared to lossless compression. JPEG, JPEG2000
image compression system follows huffman coding for image
compression. JPEG 2000 coding system use wavelet transform,
which decompose the image into different levels, where the
coefficient in each sub band are uncorrelated from coefficient of
other sub bands. Embedded Zero tree wavelet (EZW) coding exploits
the multi-resolution properties of the wavelet transform to give a
computationally simple algorithm with better performance compared
to existing wavelet transforms. For further improvement of
compression applications other coding methods were recently been
suggested. An ANN base approach is one such method. Artificial
Neural Network has been applied to many problems in image
processing and has demonstrated their superiority over classical
methods when dealing with noisy or incomplete data for image
compression applications. The performance analysis of different
images is proposed with an analysis of EZW coding system with
Error Backpropagation algorithm. The implementation and analysis
shows approximately 30% more accuracy in retrieved image
compare to the existing EZW coding system.
Abstract: This paper presents an adaptive motion estimator
that can be dynamically reconfigured by the best algorithm
depending on the variation of the video nature during the lifetime
of an application under running. The 4 Step Search (4SS) and the
Gradient Search (GS) algorithms are integrated in the estimator in
order to be used in the case of rapid and slow video sequences
respectively. The Full Search Block Matching (FSBM) algorithm
has been also integrated in order to be used in the case of the
video sequences which are not real time oriented.
In order to efficiently reduce the computational cost while
achieving better visual quality with low cost power, the proposed
motion estimator is based on a Variable Block Size (VBS) scheme
that uses only the 16x16, 16x8, 8x16 and 8x8 modes.
Experimental results show that the adaptive motion estimator
allows better results in term of Peak Signal to Noise Ratio
(PSNR), computational cost, FPGA occupied area, and dissipated
power relatively to the most popular variable block size schemes
presented in the literature.
Abstract: In high bitrate information hiding techniques, 1 bit is
embedded within each 4 x 4 Discrete Cosine Transform (DCT)
coefficient block by means of vector quantization, then the hidden bit
can be effectively extracted in terminal end. In this paper high bitrate
information hiding algorithms are summarized, and the scheme of
video in video is implemented. Experimental result shows that the host
video which is embedded numerous auxiliary information have little
visually quality decline. Peak Signal to Noise Ratio (PSNR)Y of host
video only degrades 0.22dB in average, while the hidden information
has a high percentage of survives and keeps a high robustness in
H.264/AVC compression, the average Bit Error Rate(BER) of hiding
information is 0.015%.
Abstract: Freeze concentration freezes or crystallises the water
molecules out as ice crystals and leaves behind a highly concentrated
solution. In conventional suspension freeze concentration where ice
crystals formed as a suspension in the mother liquor, separation of
ice is difficult. The size of the ice crystals is still very limited which
will require usage of scraped surface heat exchangers, which is very
expensive and accounted for approximately 30% of the capital cost.
This research is conducted using a newer method of freeze
concentration, which is progressive freeze concentration. Ice crystals
were formed as a layer on the designed heat exchanger surface. In
this particular research, a helical structured copper crystallisation
chamber was designed and fabricated. The effect of two operating
conditions on the performance of the newly designed crystallisation
chamber was investigated, which are circulation flowrate and coolant
temperature. The performance of the design was evaluated by the
effective partition constant, K, calculated from the volume and
concentration of the solid and liquid phase. The system was also
monitored by a data acquisition tool in order to see the temperature
profile throughout the process. On completing the experimental
work, it was found that higher flowrate resulted in a lower K, which
translated into high efficiency. The efficiency is the highest at 1000
ml/min. It was also found that the process gives the highest
efficiency at a coolant temperature of -6 °C.
Abstract: The switching lag-time and the voltage drop across
the power devices cause serious waveform distortions and
fundamental voltage drop in pulse width-modulated inverter output.
These phenomenons are conspicuous when both the output frequency
and voltage are low. To estimate the output voltage from the PWM
reference signal it is essential to take account of these imperfections
and to correct them. In this paper, on-line compensation method is
presented. It needs three simple blocs to add at the ideal reference
voltages. This method does not require any additional hardware
circuit and off- line experimental measurement. The paper includes
experimental results to demonstrate the validity of the proposed
method. It is applied, finally, in case of indirect vector controlled
induction machine and implemented using dSpace card.
Abstract: Single Minute Exchange of Dies (SMED) mainly focuses on recognition of internal and external activities. It is concerned particularly with transferring internal activities into external ones in as many numbers as possible, by also minimizing the internal ones. The validity of the method and procedures are verified by an application a Styrofoam manufacturing process where setup times are critical for time reduction. Significant time savings have been achieved with minimum investment. Further, the issues related with employer safety and ergonomics principles during die exchange are noted.
Abstract: Preparation of size controlled nano-particles of silver catalyst on carbon substrate from e-waste has been investigated. Chemical route was developed by extraction of the metals available in nitric acid followed by treatment with hydrofluoric acid. Silver metal particles deposited with an average size 4-10 nm. A stabilizer concentration of 10- 40 g/l was used. The average size of the prepared silver decreased with increase of the anode current density. Size uniformity of the silver nano-particles was improved distinctly at higher current density no more than 20mA... Grain size increased with EK time whereby aggregation of particles was observed after 6 h of reaction.. The chemical method involves adsorption of silver nitrate on the carbon substrate. Adsorbed silver ions were directly reduced to metal particles using hydrazine hydrate. Another alternative method is by treatment with ammonia followed by heating the carbon loaded-silver hydroxide at 980°C. The product was characterized with the help of XRD, XRF, ICP, SEM and TEM techniques.
Abstract: In this work, a special case of the image superresolution
problem where the only type of motion is global
translational motion and the blurs are shift-invariant is investigated.
The necessary conditions for exact reconstruction of the original
image by using finite impulse-response reconstruction filters are
developed. Given that the conditions are satisfied, a method for exact
super-resolution is presented and some simulation results are shown.
Abstract: In this paper, the effect of receive and/or transmit
antenna spacing on the performance (BER vs. SNR) of multipleantenna
systems is determined by using an RCS (Radar Cross
Section) channel model. In this physical model, the scatterers
existing in the propagation environment are modeled by their RCS so
that the correlation of the receive signal complex amplitudes, i.e.,
both magnitude and phase, can be estimated. The proposed RCS
channel model is then compared with classical models.
Abstract: In IETF RFC 2002, Mobile-IP was developed to
enable Laptobs to maintain Internet connectivity while moving
between subnets. However, the packet loss that comes from
switching subnets arises because network connectivity is lost while
the mobile host registers with the foreign agent and this encounters
large end-to-end packet delays. The criterion to initiate a simple and
fast full-duplex connection between the home agent and foreign
agent, to reduce the roaming duration, is a very important issue to be
considered by a work in this paper. State-transition Petri-Nets of the
modeling scenario-based CIA: communication inter-agents procedure
as an extension to the basic Mobile-IP registration process was
designed and manipulated to describe the system in discrete events.
The heuristic of configuration file during practical Setup session for
registration parameters, on Cisco platform Router-1760 using IOS
12.3 (15)T and TFTP server S/W is created. Finally, stand-alone
performance simulations from Simulink Matlab, within each subnet
and also between subnets, are illustrated for reporting better end-toend
packet delays. Results verified the effectiveness of our Mathcad
analytical manipulation and experimental implementation. It showed
lower values of end-to-end packet delay for Mobile-IP using CIA
procedure-based early registration. Furthermore, it reported packets
flow between subnets to improve losses between subnets.
Abstract: Multi-Radio Multi-Channel Wireless Mesh Networks (MRMC-WMNs) operate at the backbone to access and route high volumes of traffic simultaneously. Such roles demand high network capacity, and long “online" time at the expense of accelerated transmission energy depletion and poor connectivity. This is the problem of transmission power control. Numerous power control methods for wireless networks are in literature. However, contributions towards MRMC configurations still face many challenges worth considering. In this paper, an energy-efficient power selection protocol called PMMUP is suggested at the Link-Layer. This protocol first divides the MRMC-WMN into a set of unified channel graphs (UCGs). A UCG consists of multiple radios interconnected to each other via a common wireless channel. In each UCG, a stochastic linear quadratic cost function is formulated. Each user minimizes this cost function consisting of trade-off between the size of unification states and the control action. Unification state variables come from independent UCGs and higher layers of the protocol stack. The PMMUP coordinates power optimizations at the network interface cards (NICs) of wireless mesh routers. The proposed PMMUP based algorithm converges fast analytically with a linear rate. Performance evaluations through simulations confirm the efficacy of the proposed dynamic power control.
Abstract: Isobaric vapor-liquid equilibrium measurements are reported for the binary mixtures of n-Butylamine and Triethylamine with Cumene at 97.3 kPa. The measurements have been performed using a vapor recirculating type (modified Othmer's) equilibrium still. The binary mixture of n-Butylamine + Cumene shows positive deviation from ideality. Triethylamine + Cumene mixture shows negligible deviation from ideality. None of the systems form an azeotrope. The activity coefficients have been calculated taking into consideration the vapor phase nonideality. The data satisfy the thermodynamic consistency test of Herington. The activity coefficients have been satisfactorily correlated by means of the Margules, NRTL, and Black equations. The activity coefficient values obtained by the UNIFAC model are also reported.
Abstract: A continuum model is presented to study vdW
interaction on buckling analysis of multi-walled walled carbon
nanotube. In previous studies, only the vdW interaction between
adjacent two layers was considered and the vdW interaction between
the other two layers was neglected. The results show that the vdW
interaction cofficients are dependent on the change of interlayer
spacing and the radii of tubes. With increase of radii the vdW
coefficients approach a constant value. The numerical results show
that the effect of vdW interaction on the critical strain for a doublewalled
CNT is negligible when the radius is large enough for the
both the cases of before and after buckling.
Abstract: Since the advent of the information era, the Internet has
brought various positive effects in everyday life. Nevertheless,
recently, problems and side-effects have been noted. Internet
witch-trials and spread of pornography are only a few of these
problems.In this study, problems and causes of malicious replies on
internet boards were analyzed, using the key ideas of game theory. The
study provides a mathematical model for the internet reply game to
devise three possible plans that could efficiently counteract malicious
replies. Furthermore, seven specific measures that comply with one of
the three plans were proposed and evaluated according to the
importance and utility of each measure using the orthogonal array
survey and SPSS conjoint analysis.The conclusion was that the most
effective measure would be forbidding unsigned user access to
malicious replies. Also notable was that some analytically proposed
measures, when implemented, could backfire and encourage malicious
replies.
Abstract: IEEE 802.16 is a new wireless technology standard, it
has some advantages, including wider coverage, higher bandwidth,
and QoS support. As the new wireless technology for last mile
solution, there are designed two models in IEEE 802.16 standard. One
is PMP (point to multipoint) and the other is Mesh. In this paper we
only focus on IEEE 802.16 Mesh model. According to the IEEE
802.16 standard description, Mesh model has two scheduling modes,
centralized and distributed. Considering the pros and cons of the two
scheduling, we present the combined scheduling QoS framework that
the BS (Base Station) controls time frame scheduling and selects the
shortest path from source to destination directly. On the other hand, we
propose the Expedited Queue mechanism to cut down the transmission
time. The EQ mechanism can reduce a lot of end-to-end delay in our
QoS framework. Simulation study has shown that the average delay is
smaller than contrasts. Furthermore, our proposed scheme can also
achieve higher performance.
Abstract: In this paper, we propose an improvement of pattern
growth-based PrefixSpan algorithm, called I-PrefixSpan. The general idea of I-PrefixSpan is to use sufficient data structure for Seq-Tree
framework and separator database to reduce the execution time and
memory usage. Thus, with I-PrefixSpan there is no in-memory database stored after index set is constructed. The experimental result
shows that using Java 2, this method improves the speed of PrefixSpan up to almost two orders of magnitude as well as the memory usage to more than one order of magnitude.
Abstract: Recently in the field of bridges that are newly built or
repaired, fast construction is required more than ever. For these
reasons, precast prefabricated bridge that enables rapid construction is
actively discussed and studied today. In South Korea, it is called
modular bridge. Cross beam is an integral component of modular
bridge. It functions for load distribution, reduction of bending
moment, resistance of horizontal strength on lateral upper structure. In
this study, the structural characteristics of domestic and foreign cross
beam types were compared. Based on this, alternative cross beam
connection types suitable for modular bridge were selected. And
bulb-T girder specimens were fabricated with each type of connection.
The behavior of each specimen was analyzed under static loading, and
cross beam connection type which is expected to be best suited to
modular bridge proposed.
Abstract: Mixed convection in two-dimensional shallow rectangular enclosure is considered. The top hot wall moves with constant velocity while the cold bottom wall has no motion. Simulations are performed for Richardson number ranging from Ri = 0.001 to 100 and for Reynolds number keeping fixed at Re = 408.21. Under these conditions cavity encompasses three regimes: dominating forced, mixed and free convection flow. The Prandtl number is set to 6 and the effects of cavity inclination on the flow and heat transfer are studied for different Richardson number. With increasing the inclination angle, interesting behavior of the flow and thermal fields are observed. The streamlines and isotherm plots and the variation of the Nusselt numbers on the hot wall are presented. The average Nusselt number is found to increase with cavity inclination for Ri ³ 1 . Also it is shown that the average Nusselt number changes mildly with the cavity inclination in the dominant forced convection regime but it increases considerably in the regime with dominant natural convection.