Abstract: In this paper, we study statistical multiplexing of VBR
video in ATM networks. ATM promises to provide high speed realtime
multi-point to central video transmission for telemedicine
applications in rural hospitals and in emergency medical services.
Video coders are known to produce variable bit rate (VBR) signals
and the effects of aggregating these VBR signals need to be
determined in order to design a telemedicine network infrastructure
capable of carrying these signals. We first model the VBR video
signal and simulate it using a generic continuous-data autoregressive
(AR) scheme. We carry out the queueing analysis by the Fluid
Approximation Model (FAM) and the Markov Modulated Poisson
Process (MMPP). The study has shown a trade off: multiplexing
VBR signals reduces burstiness and improves resource utilization,
however, the buffer size needs to be increased with an associated
economic cost. We also show that the MMPP model and the Fluid
Approximation model fit best, respectively, the cell region and the
burst region. Therefore, a hybrid MMPP and FAM completely
characterizes the overall performance of the ATM statistical
multiplexer. The ramifications of this technology are clear: speed,
reliability (lower loss rate and jitter), and increased capacity in video
transmission for telemedicine. With migration to full IP-based
networks still a long way to achieving both high speed and high
quality of service, the proposed ATM architecture will remain of
significant use for telemedicine.
Abstract: Power line channel is proposed as an alternative for broadband data transmission especially in developing countries like Tanzania [1]. However the channel is affected by stochastic attenuation and deep notches which can lead to the limitation of channel capacity and achievable data rate. Various studies have characterized the channel without giving exactly the maximum performance and limitation in data transfer rate may be this is due to complexity of channel modeling being used. In this paper the channel performance of medium voltage, low voltage and indoor power line channel is presented. In the investigations orthogonal frequency division multiplexing (OFDM) with phase shift keying (PSK) as carrier modulation schemes is considered, for indoor, medium and low voltage channels with typical ten branches and also Golay coding is applied for medium voltage channel. From channels, frequency response deep notches are observed in various frequencies which can lead to reduce the achievable data rate. However, is observed that data rate up to 240Mbps is realized for a signal to noise ratio of about 50dB for indoor and low voltage channels, however for medium voltage a typical link with ten branches is affected by strong multipath and coding is required for feasible broadband data transfer.
Abstract: Novel nitrogen removal technologies via nitrite
pathway attract increasing interest in recent years. In this study,
batch experiments were performed to investigate nitrite accumulation
characteristics and shifts in nitrifying community structure at
different growth environments including ammonia concentration, pH
and alkalinity. It was found that nitrite accumulation ratios were
maintained at around 95% at studied conditions, and the optimum pH
and Alk/N (ratio between alkalinity and nitrogen) for ammonium
oxidization were 8.5 and 8.33, respectively. Fluorescence in situ
hybridization analysis of nitrifying bacteria showed that high free
ammonia (from influent ammonium or caused by high pH)
significantly altered the structure of nitrifying community, leading to
abundance of ammonia-oxidizing bacteria (AOB), especially
Nitrososmonas, and inhibition of nitrite-oxidizing bacteria (NOB).
The results suggest that free ammonia plays more important role than
other studied conditions on nitrite accumulation.
Abstract: In this study, static batch fermentation was used for bacterial cellulose production in date syrup solution (Bx. 10%) at 28°C using Gluconacetobacter. xylinus (PTCC 1734). The physicochemical properties of standard Sigma CMC and the produced carboxymethyl bacterial cellulose (CMBC) were studied using FT-IR spectroscopy, X-ray diffractometry (XRD) and Scanning Electron Microscopy (SEM). According to the FT-IR spectra the bands at 1664 and 1431 cm-1 indicate that carboxylic acid groups and carboxylate groups exist on the surface. The SEM imaging of CMBC and CMC carried out in magnification of 1K. Comparing the SEM imaging obviously showed that the ribbon shape in CMC remained but the length of ribbons became shorter while that shape changed to flake shape for CMBC. Determination of the area under XRD patterns demonstrated that the crystallinity amount of CMC was more than that for CMBC (51.08% and 81.84% for CMBC and CMC, respectively).
Abstract: The African Great Lakes Region refers to the zone
around lakes Victoria, Tanganyika, Albert, Edward, Kivu, and
Malawi. The main source of electricity in this region is hydropower
whose systems are generally characterized by relatively weak,
isolated power schemes, poor maintenance and technical deficiencies
with limited electricity infrastructures. Most of the hydro sources are
rain fed, and as such there is normally a deficiency of water during
the dry seasons and extended droughts. In such calamities fossil fuels
sources, in particular petroleum products and natural gas, are
normally used to rescue the situation but apart from them being nonrenewable,
they also release huge amount of green house gases to our
environment which in turn accelerates the global warming that has at
present reached an amazing stage. Wind power is ample, renewable,
widely distributed, clean, and free energy source that does not
consume or pollute water. Wind generated electricity is one of the
most practical and commercially viable option for grid quality and
utility scale electricity production. However, the main shortcoming
associated with electric wind power generation is fluctuation in its
output both in space and time. Before making a decision to establish
a wind park at a site, the wind speed features there should therefore
be known thoroughly as well as local demand or transmission
capacity. The main objective of this paper is to utilise monthly
average wind speed data collected from one prospective site within
the African Great Lakes Region to demonstrate that the available
wind power there is high enough to generate electricity. The mean
monthly values were calculated from records gathered on hourly
basis for a period of 5 years (2001 to 2005) from a site in Tanzania.
The documentations that were collected at a height of 2 m were
projected to a height of 50 m which is the standard hub height of
wind turbines. The overall monthly average wind speed was found to
be 12.11 m/s whereas June to November was established to be the
windy season as the wind speed during the session is above the
overall monthly wind speed. The available wind power density
corresponding to the overall mean monthly wind speed was evaluated
to be 1072 W/m2, a potential that is worthwhile harvesting for the
purpose of electric generation.
Abstract: A new approach to predict the 3D structures of proteins by combining the knowledge-based method and Molecular Dynamics Simulation is presented on the chicken villin headpiece subdomain (HP-36). Comparative modeling is employed as the knowledge-based method to predict the core region (Ala9-Asn28) of the protein while the remaining residues are built as extended regions (Met1-Lys8; Leu29-Phe36) which then further refined using Molecular Dynamics Simulation for 120 ns. Since the core region is built based on a high sequence identity to the template (65%) resulting in RMSD of 1.39 Å from the native, it is believed that this well-developed core region can act as a 'nucleation center' for subsequent rapid downhill folding. Results also demonstrate that the formation of the non-native contact which tends to hamper folding rate can be avoided. The best 3D model that exhibits most of the native characteristics is identified using clustering method which then further ranked based on the conformational free energies. It is found that the backbone RMSD of the best model compared to the NMR-MDavg is 1.01 Å and 3.53 Å, for the core region and the complete protein, respectively. In addition to this, the conformational free energy of the best model is lower by 5.85 kcal/mol as compared to the NMR-MDavg. This structure prediction protocol is shown to be effective in predicting the 3D structure of small globular protein with a considerable accuracy in much shorter time compared to the conventional Molecular Dynamics simulation alone.
Abstract: Autism Spectrum Disorders (ASDs) are characterized
by abnormalities in social interaction and communication, as well as
repetitive and stereotyped behaviors. Although various studies have
been conducted in ASDs etiology across the world, it seems that they
are still unknown in Middle East. Some scientific researches have
been conducted on ASDs in Middle East (ME) especially in
Kingdom of Saudi Arabia (KSA).
A systematic literature review was performed to identify the ASDs
studies in KSA. Accordingly, PubMed, ISI web of Science and
Google were searched to find KSA and ME studies in ASDs. The
main focus of this review work is to outline an improved
understanding of the underpinnings of ASD in order to achieve
therapeutic interventions and we will discuss the main problem we
waiting for solution with reference with role of Transcranial
Magnetic Stimulation (TMS) to modulate cortical activity improve
understanding ASD.
Abstract: Advances in processors architecture, such as multicore,
increase the size of complexity of parallel computer systems.
With multi-core architecture there are different parallel languages
that can be used to run parallel programs. One of these languages is
OpenMP which embedded in C/Cµ or FORTRAN. Because of this
new architecture and the complexity, it is very important to evaluate
the performance of OpenMP constructs, kernels, and application
program on multi-core systems. Performance is the activity of
collecting the information about the execution characteristics of a
program. Performance tools consists of at least three interfacing
software layers, including instrumentation, measurement, and
analysis. The instrumentation layer defines the measured
performance events. The measurement layer determines what
performance event is actually captured and how it is measured by the
tool. The analysis layer processes the performance data and
summarizes it into a form that can be displayed in performance tools.
In this paper, a number of OpenMP performance tools are surveyed,
explaining how each is used to collect, analyse, and display data
collection.
Abstract: Increased energy demand and the concern about
environment friendly technology, renewable bio-fuels are better
alternative to petroleum products. In the present study linseed oil was
used as alternative source for diesel engine fuel and the results were
compared with baseline data of neat diesel. Performance parameters
such as brake thermal efficiency (BTE) and brake specific fuel
consumption (BSFC) and emissions parameters such as CO,
unburned hydro carbon (UBHC), NOx, CO2 and exhaust temperature
were compared. BTE of the engine was lower and BSFC was higher
when the engine was fueled with Linseed oil compared to diesel fuel.
Emission characteristics are better than diesel fuel. NOx formation by
using linseed oil during the experiment was lower than diesel fuel.
Linseed oil is non edible oil, so it can be used as an extender of diesel
fuel energy source for small and medium energy needs.
Abstract: The objective of this experiment was to study of water
relations and chlorophyll in different wheat genotypes and their
correlations with grain and biological yields. 21 genotypes of bread
wheat were compared in a field experiment as randomized complete
blocks design with four replications. The results showed that relative
water deficit, relative water loss, excised leaf water retention, cell
membrane stability, chlorophyll-a, chlorophyll-b, total chlorophyll,
grain yield and biological yield were different significantly among
wheat genotypes, but SPAD-chlorophyll index, relative water content
and chlorophyll florescence were not. Significant correlations were
not observed among above mentioned water relations and
chlorophyll characteristics with grain yield, but there was a positive
and significant correlation between biological yield and grain yield.
Abstract: This work proposes a set of actions to assist redesign
procedure in existing products of Electric and Electronic Equipment
(EEE). The aim is to improve their environmental behavior after their
withdrawal in the End-of-Life (EOL) phase. In the beginning data
collection takes place. Then follows selection and implementation of
the optimal EOL Treatment Strategy (EOL_TS) and its results-
evaluation concerning the environment. In parallel, product design
characteristics that can be altered are selected based on their
significance for the environment in the EOL stage. All results from
the previous stages are combined and possible redesign actions are
formulated for further examination and afterwards configuration in
the design stage. The applied method to perform these tasks is Lean
Thinking (LT). At the end, results concerning the application of the
proposed method on a distribution transformer are presented.
Abstract: The commercial white tyres are usually used for forklifts in food and medicine industries. Conventionally, silica is used as reinforcement in the tyres. However, the adhesion between silica particles and rubber is remarkably poor. To improve the problem of adhesion and hence enhance wear resistance, modification of silica surface is one of the solutions. In this work, the natural rubber compound blending with polyisoprene-coated silica prepared by admicellar polymerization technique was studied to compare with the natural rubber compound of unmodified silica. The surface characterization of modified silica was also examined by SEM, FTIR, and TGA. The results show that polyisoprene-coated silica/natural rubber compound gave better overall mechanical properties, especially wear resistance with the improvement of the adhesion between silica and natural rubber matrix that can be seen in the SEM micrograph.
Abstract: The many feasible alternatives and conflicting
objectives make equipment selection in materials handling a
complicated task. This paper presents utilizing Monte Carlo (MC)
simulation combined with the Analytic Hierarchy Process (AHP) to
evaluate and select the most appropriate Material Handling
Equipment (MHE). The proposed hybrid model was built on the base
of material handling equation to identify main and sub criteria critical
to MHE selection. The criteria illustrate the properties of the material
to be moved, characteristics of the move, and the means by which the
materials will be moved. The use of MC simulation beside the AHP
is very powerful where it allows the decision maker to represent
his/her possible preference judgments as random variables. This will
reduce the uncertainty of single point judgment at conventional AHP,
and provide more confidence in the decision problem results. A small
business pharmaceutical company is used as an example to illustrate
the development and application of the proposed model.
Abstract: In the present paper the extreme shear stresses with the corresponding planes are established using the freely available computer tools like the Gnuplot, Sage, R, Python and Octave. In order to support these freely available computer tools, their strong symbolical and graphical abilities are illustrated. The nature of the stationary points obtained by the Method of Lagrangian Multipliers can be determined using freely available computer symbolical tools like Sage. The characters of the stationary points can be explained in the easiest way using freely available computer graphical tools like Gnuplot, Sage, R, Python and Octave. The presented figures improve the understanding of the problem and the obtained solutions for the majority of students of civil or mechanical engineering.
Abstract: According to Rostler method (ASTM D 2006), saturates content of bitumen is determined based on its reactivity to sulphuric acid. While Corbett method (ASTM D 4124) based on its polarity level. This paper presents results from the study on the effect of saturates content determined by two different fractionation methods on the rheological and aging characteristics of bitumen. The result indicated that the increment of saturates content tended to reduce all the rheological characteristics concerned. Bitumen became less elastic, less viscous, and less resistant to plastic deformation, but became more resistant to fatigue cracking. After short and long term aging process, the treatment effect coefficients of saturates decreased, saturates became thicker due to aging process. This study concludes that saturates is not really stable or reactive in aging process. Therefore, the reactivity of saturates should be considered in bitumen aging index
Abstract: In this paper, a new design technique for enhancing
bandwidth that improves the performance of a conventional
microstrip patch antenna is proposed. This paper presents a novel
wideband probe fed inverted slotted microstrip patch antenna. The
design adopts contemporary techniques; coaxial probe feeding,
inverted patch structure and slotted patch. The composite effect of
integrating these techniques and by introducing the proposed patch,
offer a low profile, broadband, high gain, and low cross-polarization
level. The results for the VSWR, gain and co-and cross-polarization
patterns are presented. The antenna operating the band of 1.80-2.36
GHz shows an impedance bandwidth (2:1 VSWR) of 27% and a gain
of 10.18 dBi with a gain variation of 1.12 dBi. Good radiation
characteristics, including a cross-polarization level in xz-plane less
than -42 dB, have been obtained.
Abstract: Many problems in computer vision and image
processing present potential for parallel implementations through one
of the three major paradigms of geometric parallelism, algorithmic
parallelism and processor farming. Static process scheduling
techniques are used successfully to exploit geometric and algorithmic
parallelism, while dynamic process scheduling is better suited to
dealing with the independent processes inherent in the process
farming paradigm. This paper considers the application of parallel or
multi-computers to a class of problems exhibiting spatial data
characteristic of the geometric paradigm. However, by using
processor farming paradigm, a dynamic scheduling technique is
developed to suit the MIMD structure of the multi-computers. A
hybrid scheme of scheduling is also developed and compared with
the other schemes. The specific problem chosen for the investigation
is the Hough transform for line detection.
Abstract: Natural language processing systems pose a unique
challenge for software architectural design as system complexity has
increased continually and systems cannot be easily constructed from
loosely coupled modules. Lexical, syntactic, semantic, and pragmatic
aspects of linguistic information are tightly coupled in a manner that
requires separation of concerns in a special way in design,
implementation and maintenance. An aspect oriented software
architecture is proposed in this paper after critically reviewing
relevant architectural issues. For the purpose of this paper, the
syntactic aspect is characterized by an augmented context-free
grammar. The semantic aspect is composed of multiple perspectives
including denotational, operational, axiomatic and case frame
approaches. Case frame semantics matured in India from deep
thematic analysis. It is argued that lexical, syntactic, semantic and
pragmatic aspects work together in a mutually dependent way and
their synergy is best represented in the aspect oriented approach. The
software architecture is presented with an augmented Unified
Modeling Language.
Abstract: The characterization and modeling of the dynamic
behavior of many built-up structures under vibration conditions is still
a subject of current research. The present study emphasizes the
theoretical investigation of slip damping in layered and jointed
welded cantilever structures using finite element approach.
Application of finite element method in damping analysis is relatively
recent, as such, some problems particularly slip damping analysis has
not received enough attention. To validate the finite element model
developed, experiments have been conducted on a number of mild
steel specimens under different initial conditions of vibration. Finite
element model developed affirms that the damping capacity of such
structures is influenced by a number of vital parameters such as;
pressure distribution, kinematic coefficient of friction and micro-slip
at the interfaces, amplitude, frequency of vibration, length and
thickness of the specimen. Finite element model developed can be
utilized effectively in the design of machine tools, automobiles,
aerodynamic and space structures, frames and machine members for
enhancing their damping capacity.
Abstract: In this paper, some experiments of liquid dispersion flow driven by explosion in vertical plane were carried out using a liquid explosive dispersion device with film cylindrical constraints. The separated time series describing the breakup shape and dispersion process of liquid were recorded with high speed CMOS camera. The experimental results were analyzed and some essential characteristics of liquid dispersing flow are presented.