Abstract: This paper presents a novel three-phase utility
frequency to high frequency soft switching power conversion circuit
with dual mode pulse width modulation and pulse density modulation
for high power induction heating applications as melting of steel and
non ferrous metals, annealing of metals, surface hardening of steel
and cast iron work pieces and hot water producers, steamers and
super heated steamers. This high frequency power conversion circuit
can operate from three-phase systems to produce high current for
high power induction heating applications under the principles of
ZVS and it can regulate its ac output power from the rated value to a
low power level. A dual mode modulation control scheme based on
high frequency PWM in synchronization with the utility frequency
positive and negative half cycles for the proposed high frequency
conversion circuit and utility frequency pulse density modulation is
produced to extend its soft switching operating range for wide ac
output power regulation. A dual packs heat exchanger assembly is
designed to be used in consumer and industrial fluid pipeline systems
and it is proved to be suitable for the hot water, steam and super
heated steam producers. Experiment and simulation results are given
in this paper to verify the operation principles of the proposed ac
conversion circuit and to evaluate its power regulation and
conversion efficiency. Also, the paper presents a mutual coupling
model of the induction heating load instead of equivalent transformer
circuit model.
Abstract: A simple network model is developed in OPNET to
study the performance of the Wi-Fi protocol. The model is simulated
in OPNET and performance factors such as load, throughput and delay
are analysed from the model. Four applications such as oracle, http, ftp
and voice are applied over the Wireless LAN network to determine the
throughput. The voice application utilises a considerable amount of
bandwidth of up to 5Mbps, as a result the 802.11g standard of the
Wi-Fi protocol was chosen which can support a data rate of up to
54Mbps. Results indicate that when the load in the Wi-Fi network is
increased the queuing delay on the point-to-point links in the Wi-Fi
network significantly reduces until it is comparable to that of WiMAX.
In conclusion, the queuing delay of the Wi-Fi protocol for the network
model simulated was about 0.00001secs comparable to WiMAX
network values.
Abstract: Acute toxicity of nano SiO2, ZnO, MCM-41 (Meso
pore silica), Cu, Multi Wall Carbon Nano Tube (MWCNT), Single
Wall Carbon Nano Tube (SWCNT) , Fe (Coated) to bacteria Vibrio
fischeri using a homemade luminometer , was evaluated. The values
of the nominal effective concentrations (EC), causing 20% and 50%
inhibition of biouminescence, using two mathematical models at two
times of 5 and 30 minutes were calculated. Luminometer was
designed with Photomultiplier (PMT) detector. Luminol
chemiluminescence reaction was carried out for the calibration graph.
In the linear calibration range, the correlation coefficients and
coefficient of Variation (CV) were 0.988 and 3.21% respectively
which demonstrate the accuracy and reproducibility of the instrument
that are suitable. The important part of this research depends on how
to optimize the best condition for maximum bioluminescence. The
culture of Vibrio fischeri with optimal conditions in liquid media,
were stirring at 120 rpm at a temperature of 150C to 180C and were
incubated for 24 to 72 hours while solid medium was held at 180C
and for 48 hours. Suspension of nanoparticles ZnO, after 30 min
contact time to bacteria Vibrio fischeri, showed the highest toxicity
while SiO2 nanoparticles showed the lowest toxicity. After 5 min
exposure time, the toxicity of ZnO was the strongest and MCM-41
was the weakest toxicant component.
Abstract: Innovations and innovative activity get the increasing
value for successful financial and economic activity of the countries
and regions. The level of innovative sphere development determines
place of a country or a region in world economy and forms a basis of
steady economic growth. This article is devoted to different aspects
of organization of the national economic safety in the conditions of
innovative development, its problems, risks and threats. Economy
can be considered as aspiring for transition to innovative way only
with finding of economic safety: financial independence, power
stability and technological progress. There are statistical indicators,
defining the level of economic security and factors, threatening
economic safety of the state. The research is based on the analysis of
factors and indicators in conditions of innovative development. The
paper is illustrated by the examples of possible estimated system of
the economic safety level.
Abstract: The aim of this study was to analyse the most
important parameters determining the quality of the motion structure
of the basic classical dance jump – grand jeté.Research sample
consisted of 8 students of the Dance Conservatory in Brno. Using the
system Simi motion we performed a 3D kinematic analysis of the
jump. On the basis of the comparison of structure quality and
measured data of the grand jeté, we defined the optimal values of the
relevant parameters determining the quality of the performance. The
take-off speed should achieve about 2.4 m·s-1, the optimum take-off
angle is 28 - 30º. The take-off leg should swing backward at the
beginning of the flight phase with the minimum speed of 3.3 m·s-1.If
motor abilities of dancers achieve the level necessary for optimal
performance of a classical dance jump, there is room for certain
variability of the structure of the dance jump.
Abstract: Use of microemulsion in enhanced oil recovery has become more attractive in recent years because of its high level of extraction efficiency. Experimental investigations have been made on characterization of microemulsions of oil-brinesurfactant/ cosurfactant system for its use in enhanced oil recovery (EOR). Sodium dodecyl sulfate, propan-1-ol and heptane were selected as surfactant, cosurfactant and oil respectively for preparation of microemulsion. The effects of salinity on the relative phase volumes and solubilization parameters have also been studied. As salinity changes from low to high value, phase transition takes place from Winsor I to Winsor II via Winsor III. Suitable microemulsion composition has been selected based on its stability and ability to reduce interfacial tension. A series of flooding experiments have been performed using the selected microemulsion. The flooding experiments were performed in a core flooding apparatus using uniform sand pack. The core holder was tightly packed with uniform sands (60-100 mesh) and saturated with brines of different salinities. It was flooded with the brine at 25 psig and the absolute permeability was calculated from the flow rate of the through sand pack. The sand pack was then flooded with the crude oil at 800 psig to irreducible water saturation. The initial water saturation was determined on the basis of mass balance. Waterflooding was conducted by placing the coreholder horizontally at a constant injection pressure at 200 pisg. After water flooding, when water-cut reached above 95%, around 0.5 pore volume (PV) of the above microemulsion slug was injected followed by chasing water. The experiments were repeated using different composition of microemulsion slug. The additional recoveries were calculated by material balance. Encouraging results with additional recovery more than 20% of original oil in place above the conventional water flooding have been observed.
Abstract: Biodiversity crisis is one of the many crises that
started at the turn of the millennia. Concrete form of expression is
still disputed, but there is a relatively high consensus regarding the
high rate of degradation and the urgent need for action. The strategy
of action outlines a strong economic component, together with the
recognition of market mechanisms as the most effective policies to
protect biodiversity. In this context, biodiversity and ecosystem
services are natural assets that play a key role in economic strategies
and technological development to promote development and
prosperity. Developing and strengthening policies for transition to an
economy based on efficient use of resources is the way forward.
To emphasize the co-viability specific to the connection economyecosystem
services, scientific approach aimed on one hand how to
implement policies for nature conservation and on the other hand, the
concepts underlying the economic expression of ecosystem services-
value, in the context of current technology. Following the analysis of
business opportunities associated with changes in ecosystem services
was concluded that development of market mechanisms for nature
conservation is a trend that is increasingly stronger individualized
within recent years. Although there are still many controversial issues
that have already given rise to an obvious bias, international
organizations and national governments have initiated and
implemented in cooperation or independently such mechanisms.
Consequently, they created the conditions for convergence between
private interests and social interests of nature conservation, so there
are opportunities for ongoing business development which leads,
among other things, the positive effects on biodiversity. Finally,
points out that markets fail to quantify the value of most ecosystem
services. Existing price signals reflect at best, only a proportion of the
total amount corresponding provision of food, water or fuel.
Abstract: The effect of magnetic field on germination
characteristics of two wheat Seeds has been studied under laboratory
conditions. Seeds were magnetically exposed to magnetic field
strengths, 125 or 250mT for different periods of time. Mean
germination time and the time required to obtain 10, 25, 50, 75 and
90%of seeds to germinate were calculated. The germination time for
each treatment were in general, higher than corresponding control
values, in the other word in treated seeds time required for mean seed
germination time increased nearly 3 hours in compared non treated
control seeds. T10 for doses D5, D6, D11 and D12 significantly higher
than the control values for both cultivars. Mean germination time
(MGT) in both cultivars significantly increased when the time of
seed exposed at magnetic field treatments increased , about 3 and 2
hour respectively for Omid and BCR cultivars.
Abstract: The paper describes ergonomics problems trend of
student at B5101 classroom building 2, Suranaree University of
Technology. The objective to survey ergonomics problems and effect
from use chairs for sitting in class room. The result from survey
method 100 student they use lecture chair for sitting in classroom
more than 2 hours/ day by RULA[1]. and Body discomfort survey[2].
The result from Body discomfort survey contribute fatigue problems
at neck, lower back, upper back and right shoulder 2.93, 2.91, 2.33,
1.75 respectively and result from RULA contribute fatigue problems
at neck, body and right upper arm 4.00, 3.75 and 3.00 respectively
are consistent. After that the researcher provide improvement plan
for design new chair support student fatigue reduction by prepare
data of sample anthropometry and design ergonomics chair prototype
3 unit. Then sample 100 student trial to use new chair and evaluate
again by RULA, Body discomfort and satisfaction. The result from
trial new chair after improvement by RULA present fatigue reduction
average of head and neck from 4.00 to 2.25 , body and trunk from
3.75 to 2.00 and arm force from 1.00 to 0.25 respectively. The result
from trial new chair after improvement by Body discomfort present
fatigue reduction average of lower back from 2.91 to 0.87, neck from
2.93 to 1.24, upper back 2.33 to 0.84 and right upper arm from 1.75
to 0.74. That statistical of RULA and Body discomfort survey
present fatigue reduction after improvement significance with a
confidence level of 95% (p-value 0.05). When analyzing the
relationship of fatigue as part of the body by Chi – square test during
RULA and Body discomfort that before and after improvements were
consistent with the significant level of confidence 95% (p-value 0.05)
. Moreover the students satisfaction result from trial with a new chair
for 30 minutes [3]. 72 percent very satisfied of the folding of the
secondary writing simple 66% the width of the writing plate, 64% the
suitability of the writing plate, 62% of soft seat cushion and 61%
easy to seat the chair.
Abstract: This study aims to assess the environmental hazards
from radon exhalation rate in the soil samples in selected locations in
Iraqi Kurdistan, using passive (CR-39NTDs) and active (RAD7)
detecting method. Radon concentration, effective radium content and
radon exhalation rate were estimated in soil samples that collected at
the depth level of 30 cm inside 124 houses. The results show that the
emanation rate for radon gas was variation from location to other,
depending on the geological formation. Most health risks come from
emanation of radon and its daughter due to its contribution for indoor
radon, so the results showed that there is a linear relationship
between the ratio of soil and indoor radon concentration (CSoil Rn222/
Cindoor Rn222) and the effective radium content in soil samples. The
results show that radon concentration has high and low values in
Hajyawa city and Er. Tyrawa Qr, respectively. A comparison
between our results with that mentioned in international reports was
done.
Abstract: The production of biodiesel from crude palm oil with
a homogeneous base catalyst is unlikely owing to considerable
formation of soap. Free fatty acids (FFA) in crude palm oil need to
be reduced, e.g. by esterification. This study investigated the activity
of sulfated zirconia calcined at various temperatures for esterification
of FFA in crude palm oil to biodiesel. It was found that under a
proper reaction condition, sulfated zirconia well catalyzes
esterification. FFA content can be reduced to an acceptable value for
typical biodiesel production with a homogeneous base catalyst.
Crystallinity and sulfate attachment of sulfated zirconia depend on
calcination temperature during the catalyst preparation. Too low
temperature of calcination gives amorphous sulfated zirconia which
has low activity for esterification of FFA. In contrast, very high
temperature of calcination removes sulfate group, consequently,
conversion of FFA is reduced. The appropriate temperature range of
calcination is 550-650 oC.
Abstract: This study aims to determine the level of resistance of Hevea brasiliensis and Paraserianthes falcataria (synonym: Falcataria molucana) against wood rot fungi Pleurotus ostreatus based on Indonesian standard SNI 01.7207-2006 and Japanese standard JIS K 1571-2004. The variables measured were visual appearance and weight loss percentage of wood based on longitudinal and cross section fiber directions of rubber wood and sengon wood. Measurement of oven dry weight loss of wood samples performed after 12 weeks incubation. Replication performed was 10 times at each treatment combination. The results based on SNI 01.7207-2006, weight loss value of H. brasiliensis and P. falcataria wood with fiber direction longitudinal were 23,12 and 22,25% respectively and cross section were 20,77 and 18,76% respectively, and all were classified to resistance class IV (no resistance). The results based on JIS K 1571-2004, weight loss value of both woods with fiber direction cross section were 10,95 and 14,20% respectively.
Abstract: the effects of refining and alkaline chemicals on potential of recycling bleached chemical pulp of bagasse were investigated in this study. Recycling was done until three times. Handsheet properties such as, apparent density, light scattering coefficient, tear index, burst index, breaking length, and fold number according to TAPPI standard were measured. Water retention value also was used to considering the treatments during recycling. Refining enhanced the strength of recycled pulp by increasing fiber flexibility and swelling ability, whereas by applying chemical treatment didn't observe any improvement. The morphology of recycled fiber was considered with scanning electron microscopy (SEM).
Abstract: Bus Rapid Transit (BRT) has emerged as a cost-effective transport system for urban mobility. However its ability to stimulate land development remains largely unexplored. The study makes use of qualitative (interview method) and quantitative analysis (questionnaire survey and longitudinal analysis of property data) to investigate land development impact resulting from BRT in Beijing, China. The empirical analysis suggests that BRT has a positive impact on the residential and commercial property attractiveness along the busway corridor. The statistical analysis suggests that accessibility advantage conferred by BRT is capitalized into higher property price. The average price of apartments adjacent to a BRT station has gained a relatively faster increase than those not served by the BRT system. The capitalization effect mostly occurs after the full operation of BRT, and is more evident over time and particularly observed in areas which previously lack alternative mobility opportunity.
Abstract: Pre-germinated parboiled brown rice or Khao hang (in Thai) is paddy which undergoing the processes of soaking, steaming, drying and dehusking to obtain the edible form for consumption. The objectives of this research were to study the kinetic of pre-germinated parboiled brown rice drying using fluidization technique and to study the properties of pre-germinated parboiled brown rice after drying. The dryings were performed at the different temperatures of 110, 120 and 130 oC at the bed depth of 2 cm with the air velocity of 1.98 m/s. The results found that the higher drying temperature led to the faster moisture reduction. After drying until the moisture content of pre-germinated parboiled brown rice was lower than 14%wet basis, samples were taken to determine various qualities such as percentage of head rice and L* a* b* color values. The shade drying was used as a control. The results found that the higher drying temperature resulted in the decrease of head rice percentage. For the color assessment, the trend of L* and a* values was increased with the drying temperature, while the b* value was not significantly difference (p › 0.05) by drying temperatures. However, the b value of drying by fluidized bed dryer was higher than the control.
Abstract: Fault-proneness of a software module is the
probability that the module contains faults. A correlation exists
between the fault-proneness of the software and the measurable
attributes of the code (i.e. the static metrics) and of the testing (i.e.
the dynamic metrics). Early detection of fault-prone software
components enables verification experts to concentrate their time and
resources on the problem areas of the software system under
development. This paper introduces Genetic Algorithm based
software fault prediction models with Object-Oriented metrics. The
contribution of this paper is that it has used Metric values of JEdit
open source software for generation of the rules for the classification
of software modules in the categories of Faulty and non faulty
modules and thereafter empirically validation is performed. The
results shows that Genetic algorithm approach can be used for
finding the fault proneness in object oriented software components.
Abstract: So much energy is used in high rise buildings to fulfill
the basic needs of users such as lighting and thermal comfort.
Malaysia has hot and humid climate, buildings especially high rise
buildings receive unnecessary solar radiation that cause more solar
heat gain. Energy use specially electricity consumption in high rise
buildings has increased. There have been growing concerns about
energy consumption and its effect on environment. Building, energy
and the environment are important issues that the designers should
consider to them. Self protected form is one of possible ways against
the impact of solar radiation in high rise buildings. The Energy
performance of building envelopes was investigated in term of the
Overall Thermal Transfer Value (OTTV ).In this paper, the amount
of OTTV reduction was calculated through OTTV Equations to
clear the effectiveness of self shading strategy on minimizing energy
consumption for cooling interior spaces in high rise buildings which
has considerable envelope areas against solar radiation. Also increasing
the optimum window area was investigated using self-shading
strategy in designing high rise buildings. As result, the significant
reduction in OTTV was shown based on WWR.In addition slight
increase was demonstrated in WWR that can influence on visible
comfort interior spaces.
Abstract: An effort has been taken to simulate the combustion
and performance characteristics of biodiesel fuel in direct injection
(D.I) low heat rejection (LHR) diesel engine. Comprehensive
analyses on combustion characteristics such as cylinder pressure,
peak cylinder pressure, heat release and performance characteristics
such as specific fuel consumption and brake thermal efficiency are
carried out. Compression ignition (C.I) engine cycle simulation was
developed and modified in to LHR engine for both diesel and
biodiesel fuel. On the basis of first law of thermodynamics the
properties at each degree crank angle was calculated. Preparation and
reaction rate model was used to calculate the instantaneous heat
release rate. A gas-wall heat transfer calculations are based on the
ANNAND-s combined heat transfer model with instantaneous wall
temperature to analyze the effect of coating on heat transfer. The
simulated results are validated by conducting the experiments on the
test engine under identical operating condition on a turbocharged D.I
diesel engine. In this analysis 20% of biodiesel (derived from
Jatropha oil) blended with diesel and used in both conventional and
LHR engine. The simulated combustion and performance
characteristics results are found satisfactory with the experimental
value.
Abstract: This paper To get the angle value with a MEMS rate
gyroscope in some specific field, the usual method is to make an
integral operation to the rate output, which will lead the error
cumulating effect. So the rate gyro is not suitable. MEMS rate
integrating gyroscope (MRIG) will solve this problem. A DSP system
has been developed to implement the control arithmetic. The system
can measure the angle of rotation directly by the control loops that
make the sensor work in whole-angle mode. Modeling the system with
MATLAB, desirable results of angle outputs are got, which prove the
feasibility of the control arithmetic.
Abstract: Industrial robots play a vital role in automation
however only little effort are taken for the application of robots in
machining work such as Grinding, Cutting, Milling, Drilling,
Polishing etc. Robot parallel manipulators have high stiffness,
rigidity and accuracy, which cannot be provided by conventional
serial robot manipulators. The aim of this paper is to perform the
modeling and the workspace analysis of a 3 DOF Parallel
Manipulator (3 DOF PM). The 3 DOF PM was modeled and
simulated using 'ADAMS'. The concept involved is based on the
transformation of motion from a screw joint to a spherical joint
through a connecting link. This paper work has been planned to
model the Parallel Manipulator (PM) using screw joints for very
accurate positioning. A workspace analysis has been done for the
determination of work volume of the 3 DOF PM. The position of the
spherical joints connected to the moving platform and the
circumferential points of the moving platform were considered for
finding the workspace. After the simulation, the position of the joints
of the moving platform was noted with respect to simulation time and
these points were given as input to the 'MATLAB' for getting the
work envelope. Then 'AUTOCAD' is used for determining the work
volume. The obtained values were compared with analytical
approach by using Pappus-Guldinus Theorem. The analysis had been
dealt by considering the parameters, link length and radius of the
moving platform. From the results it is found that the radius of
moving platform is directly proportional to the work volume for a
constant link length and the link length is also directly proportional
to the work volume, at a constant radius of the moving platform.