Abstract: Particle Swarm Optimization (PSO) with elite PSO
parameters has been developed for power flow analysis under
practical constrained situations. Multiple solutions of the power flow
problem are useful in voltage stability assessment of power system.
A method of determination of multiple power flow solutions is
presented using a hybrid of Particle Swarm Optimization (PSO) and
local search technique. The unique and innovative learning factors of
the PSO algorithm are formulated depending upon the node power
mismatch values to be highly adaptive with the power flow problems.
The local search is applied on the pbest solution obtained by the PSO
algorithm in each iteration. The proposed algorithm performs reliably
and provides multiple solutions when applied on standard and illconditioned
systems. The test results show that the performances of
the proposed algorithm under critical conditions are better than the
conventional methods.
Abstract: In this research it is aimed that the effect of some demographic factors on Turkish Adolescents' subjective well being is investigated. 432 adolescents who are 247 girls and 185 boys are participated in this study. They are ages 15-17, and also are high school students. The Positive and Negative Affect Scale and Life Satisfaction Scale are used for measuring adolescents' subjective well being. The ANOVA method is used in order to examine the effect of ages. For gender differences, independent t-test method is used, and finally the Pearson Correlation method is used so as to examine the effect of socio economic statues of adolescents' parents. According to results, there is no gender difference on adolescents' subjective well being. On the other hand, SES and age are effect significantly lover level on adolescents' subjective well being.
Abstract: The line start permanent magnet motor (LSPMM)
combines a permanent magnet rotor for a better motor efficiency
during synchronous running with an induction motor squirrel cage
rotor to permit the motor starting by direct coupling to power source.
In this paper effect of the rotor structure on a line start synchronous
permanent magnet motor (LSPMM) is analyzed. LSPMM motor with
three different structures for rotor is designed by using RMxprt
software; efficiency and line current of LSPMM motor for different
structures in full-load condition have been presented. The results
indicate that with correct choosing of rotor structure, maximum
efficiency can be found.
Abstract: Structural behavior of ring stiffened thick walled
cylinders made of functionally graded materials (FGMs) is
investigated in this paper. Functionally graded materials are inhomogeneous composites which are usually made from a mixture
of metal and ceramic. The gradient compositional variation of the
constituents from one surface to the other provides an elegant solution to the problem of high transverse shear stresses that are
induced when two dissimilar materials with large differences in material properties are bonded. FGM formation of the cylinder is
modeled by power-law exponent and the variation of characteristics is supposed to be in radial direction.
A finite element formulation is derived for the analysis. According to the property variation of the constituent materials in the radial
direction of the wall, it is not convenient to use conventional elements to model and analyze the structure of the stiffened FGM
cylinders. In this paper a new cylindrical super-element is used to model the finite element formulation and analyze the static and
modal behavior of stiffened FGM thick walled cylinders. By using
this super-element the number of elements, which are needed for
modeling, will reduce significantly and the process time is less in comparison with conventional finite element formulations. Results for static and modal analysis are evaluated and verified by
comparison to finite element formulation with conventional
elements. Comparison indicates a good conformity between results.
Abstract: An optimal power flow (OPF) based on particle swarm
optimization (PSO) was developed with more realistic generator
security constraint using the capability curve instead of only Pmin/Pmax
and Qmin/Qmax. Neural network (NN) was used in designing digital
capability curve and the security check algorithm. The algorithm is
very simple and flexible especially for representing non linear
generation operation limit near steady state stability limit and under
excitation operation area. In effort to avoid local optimal power flow
solution, the particle swarm optimization was implemented with
enough widespread initial population. The objective function used in
the optimization process is electric production cost which is
dominated by fuel cost. The proposed method was implemented at
Java Bali 500 kV power systems contain of 7 generators and 20
buses. The simulation result shows that the combination of generator
power output resulted from the proposed method was more economic
compared with the result using conventional constraint but operated
at more marginal operating point.
Abstract: Inverse kinematics analysis plays an important role in developing a robot manipulator. But it is not too easy to derive the inverse kinematic equation of a robot manipulator especially robot manipulator which has numerous degree of freedom. This paper describes an application of Artificial Neural Network for modeling the inverse kinematics equation of a robot manipulator. In this case, the robot has three degree of freedoms and the robot was implemented for drilling a printed circuit board. The artificial neural network architecture used for modeling is a multilayer perceptron networks with steepest descent backpropagation training algorithm. The designed artificial neural network has 2 inputs, 2 outputs and varies in number of hidden layer. Experiments were done in variation of number of hidden layer and learning rate. Experimental results show that the best architecture of artificial neural network used for modeling inverse kinematics of is multilayer perceptron with 1 hidden layer and 38 neurons per hidden layer. This network resulted a RMSE value of 0.01474.
Abstract: This paper features the modeling and design of a Fast
Output Sampling (FOS) Feedback control technique for the Active
Vibration Control (AVC) of a smart flexible aluminium cantilever
beam for a Single Input Single Output (SISO) case. Controllers are
designed for the beam by bonding patches of piezoelectric layer as
sensor / actuator to the master structure at different locations along
the length of the beam by retaining the first 2 dominant vibratory
modes. The entire structure is modeled in state space form using the
concept of piezoelectric theory, Euler-Bernoulli beam theory, Finite
Element Method (FEM) and the state space techniques by dividing
the structure into 3, 4, 5 finite elements, thus giving rise to three
types of systems, viz., system 1 (beam divided into 3 finite
elements), system 2 (4 finite elements), system 3 (5 finite elements).
The effect of placing the sensor / actuator at various locations along
the length of the beam for all the 3 types of systems considered is
observed and the conclusions are drawn for the best performance and
for the smallest magnitude of the control input required to control the
vibrations of the beam. Simulations are performed in MATLAB. The
open loop responses, closed loop responses and the tip displacements
with and without the controller are obtained and the performance of
the proposed smart system is evaluated for vibration control.
Abstract: A general stochastic spatial MIMO channel model is
proposed for evaluating various MIMO techniques in this paper. It can
generate MIMO channels complying with various MIMO
configurations such as smart antenna, spatial diversity and spatial
multiplexing. The modeling method produces the stochastic fading
involving delay spread, Doppler spread, DOA (direction of arrival),
AS (angle spread), PAS (power azimuth Spectrum) of the scatterers,
antenna spacing and the wavelength. It can be applied in various
MIMO technique researches flexibly with low computing complexity.
Abstract: This paper applies Bayesian Networks to support
information extraction from unstructured, ungrammatical, and
incoherent data sources for semantic annotation. A tool has been
developed that combines ontologies, machine learning, and
information extraction and probabilistic reasoning techniques to
support the extraction process. Data acquisition is performed with the
aid of knowledge specified in the form of ontology. Due to the
variable size of information available on different data sources, it is
often the case that the extracted data contains missing values for
certain variables of interest. It is desirable in such situations to
predict the missing values. The methodology, presented in this paper,
first learns a Bayesian network from the training data and then uses it
to predict missing data and to resolve conflicts. Experiments have
been conducted to analyze the performance of the presented
methodology. The results look promising as the methodology
achieves high degree of precision and recall for information
extraction and reasonably good accuracy for predicting missing
values.
Abstract: This study is concerned with a new adaptive impedance control strategy to compensate for unknown time-varying environment stiffness and position. The uncertainties are expressed by Function Approximation Technique (FAT), which allows the update laws to be derived easily using Lyapunov stability theory. Computer simulation results are presented to validate the effectiveness of the proposed strategy.
Abstract: There is a acute water problem especially in the dry
season in and around Perundurai (Erode district, Tamil Nadu, India)
where there are more number of tannery units. Hence an attempt was
made to use the waste water from tannery industry for construction
purpose. The mechanical properties such as compressive strength,
tensile strength, flexural strength etc were studied by casting various
concrete specimens in form of cube, cylinders and beams etc and
were found to be satisfactory. Hence some special properties such as
chloride attack, sulphate attack and chemical attack are considered
and comparatively studied with the conventional potable water. In
this experimental study the results of specimens prepared by using
treated and untreated tannery effluent were compared with the
concrete specimens prepared by using potable water. It was observed
that the concrete had some reduction in strength while subjected to
chloride attack, sulphate attack and chemical attack. So admixtures
were selected and optimized in suitable proportion to counter act the
adverse effects and the results were found to be satisfactory.
Abstract: Recently, many existing partially blind signature scheme based on a single hard problem such as factoring, discrete logarithm, residuosity or elliptic curve discrete logarithm problems. However sooner or later these systems will become broken and vulnerable, if the factoring or discrete logarithms problems are cracked. This paper proposes a secured partially blind signature scheme based on factoring (FAC) problem and elliptic curve discrete logarithms (ECDL) problem. As the proposed scheme is focused on factoring and ECDLP hard problems, it has a solid structure and will totally leave the intruder bemused because it is very unlikely to solve the two hard problems simultaneously. In order to assess the security level of the proposed scheme a performance analysis has been conducted. Results have proved that the proposed scheme effectively deals with the partial blindness, randomization, unlinkability and unforgeability properties. Apart from this we have also investigated the computation cost of the proposed scheme. The new proposed scheme is robust and it is difficult for the malevolent attacks to break our scheme.
Abstract: The join dependency provides the basis for obtaining
lossless join decomposition in a classical relational schema. The
existence of Join dependency shows that that the tables always
represent the correct data after being joined. Since the classical
relational databases cannot handle imprecise data, they were
extended to fuzzy relational databases so that uncertain, ambiguous,
imprecise and partially known information can also be stored in
databases in a formal way. However like classical databases, the
fuzzy relational databases also undergoes decomposition during
normalization, the issue of joining the decomposed fuzzy relations
remains intact. Our effort in the present paper is to emphasize on this
issue. In this paper we define fuzzy join dependency in the
framework of type-1 fuzzy relational databases & type-2 fuzzy
relational databases using the concept of fuzzy equality which is
defined using fuzzy functions. We use the fuzzy equi-join operator
for computing the fuzzy equality of two attribute values. We also
discuss the dependency preservation property on execution of this
fuzzy equi- join and derive the necessary condition for the fuzzy
functional dependencies to be preserved on joining the decomposed
fuzzy relations. We also derive the conditions for fuzzy join
dependency to exist in context of both type-1 and type-2 fuzzy
relational databases. We find that unlike the classical relational
databases even the existence of a trivial join dependency does not
ensure lossless join decomposition in type-2 fuzzy relational
databases. Finally we derive the conditions for the fuzzy equality to
be non zero and the qualification of an attribute for fuzzy key.
Abstract: The use of renewable energy sources becomes more
necessary and interesting. As wider applications of renewable energy
devices at domestic, commercial and industrial levels has not only
resulted in greater awareness, but also significantly installed
capacities. In addition, biomass principally is in the form of woods,
which is a form of energy by humans for a long time. Gasification is
a process of conversion of solid carbonaceous fuel into combustible
gas by partial combustion. Many gasifier models have various
operating conditions; the parameters kept in each model are different.
This study applied experimental data, which has three inputs, which
are; biomass consumption, temperature at combustion zone and ash
discharge rate. One output is gas flow rate. For this paper, neural
network was used to identify the gasifier system suitable for the
experimental data. In the result,neural networkis usable to attain the
answer.
Abstract: This paper presents the experimental results on
artificial ageing test of 22 kV XLPE cable for distribution system
application in Thailand. XLPE insulating material of 22 kV cable
was sliced to 60-70 μm in thick and was subjected to ac high voltage
at 23
Ôùª
C, 60
Ôùª
C and 75
Ôùª
C. Testing voltage was constantly applied to
the specimen until breakdown. Breakdown voltage and time to
breakdown were used to evaluate life time of insulating material.
Furthermore, the physical model by J. P. Crine for predicts life time
of XLPE insulating material was adopted as life time model and was
calculated in order to compare the experimental results. Acceptable
life time results were obtained from Crine-s model comparing with
the experimental result. In addition, fourier transform infrared
spectroscopy (FTIR) for chemical analysis and scanning electron
microscope (SEM) for physical analysis were conducted on tested
specimens.
Abstract: The main goal of this paper is to study Statistical Process Control (SPC) with Exponentially Weighted Moving Average (EWMA) control chart when observations are serially-correlated. The characteristic of control chart is Average Run Length (ARL) which is the average number of samples taken before an action signal is given. Ideally, an acceptable ARL of in-control process should be enough large, so-called (ARL0). Otherwise it should be small when the process is out-of-control, so-called Average of Delay Time (ARL1) or a mean of true alarm. We find explicit formulas of ARL for EWMA control chart for Seasonal Autoregressive and Moving Average processes (SARMA) with Exponential white noise. The results of ARL obtained from explicit formula and Integral equation are in good agreement. In particular, this formulas for evaluating (ARL0) and (ARL1) be able to get a set of optimal parameters which depend on smoothing parameter (λ) and width of control limit (H) for designing EWMA chart with minimum of (ARL1).
Abstract: In July 2012, an indoor/outdoor monitoring
programme was undertaken in two university sports facilities: a
fronton and a gymnasium. Comfort parameters (temperature, relative
humidity, CO and CO2) and total volatile organic compounds
(VOCs) were continuously monitored. Concentrations of NO2,
carbonyl compounds and individual VOCs were obtained. Low
volume samplers were used to collect particulate matter (PM10). The
minimum ventilation rates stipulated for acceptable indoor air quality
were observed in both sports facilities. It was found that cleaning
activities may have a large influence on the VOC levels. Acrolein
was one of the most abundant carbonyl compounds, showing
concentrations above the recommended limit. Formaldehyde was
detected at levels lower than those commonly reported for other
indoor environments. The PM10 concentrations obtained during the
occupancy periods ranged between 38 and 43μgm-3 in the fronton and
from 154 to 198μgm-3 in the gymnasium.
Abstract: Aptamers are useful tools in microorganism
researches, diagnoses, and treatment. Aptamers are specific target
molecules formed by oligonucleic acid molecules, and are not
decomposed by alcohol. Aptamers used to detect Mycobacterium
tuberculosis (MTB) have been proved to have specific affinity to the
outer membrane proteins of MTB. This article presents a biosensor
chip set with aptamers for early detection of MTB with high specificity
and sensitivity, even in very low concentration. Meanwhile, we have
already made a modified hydrophobic facial mask module with
internal rendering hydrophobic for effectively collecting M.
tuberculosis.
Abstract: In this research paper we have presented control
architecture for robotic arm movement and trajectory planning using
Fuzzy Logic (FL) and Genetic Algorithms (GAs). This architecture is
used to compensate the uncertainties like; movement, friction and
settling time in robotic arm movement. The genetic algorithms and
fuzzy logic is used to meet the objective of optimal control
movement of robotic arm. This proposed technique represents a
general model for redundant structures and may extend to other
structures. Results show optimal angular movement of joints as result
of evolutionary process. This technique has edge over the other
techniques as minimum mathematics complexity used.
Abstract: A scalable QoS aware multicast deployment in
DiffServ networks has become an important research dimension in
recent years. Although multicasting and differentiated services are
two complementary technologies, the integration of the two
technologies is a non-trivial task due to architectural conflicts
between them. A popular solution proposed is to extend the
functionality of the DiffServ components to support multicasting. In
this paper, we propose an algorithm to construct an efficient QoSdriven
multicast tree, taking into account the available bandwidth per
service class. We also present an efficient way to provision the
limited available bandwidth for supporting heterogeneous users. The
proposed mechanism is evaluated using simulated tests. The
simulated result reveals that our algorithm can effectively minimize
the bandwidth use and transmission cost