Abstract: This paper aims to study the effect of cold work
condition on the microstructure of Cu-1.5wt%Ti, and Cu-3.5wt%Ti
and hence mechanical properties. The samples under investigation
were machined, and solution heat treated. X-ray diffraction technique
is used to identify the different phases present after cold deformation
by compression and also different heat treatment and also measuring
the relative quantities of phases present. The metallographic
examination is used to study the microstructure of the samples. The
hardness measurements were used to indicate the change in
mechanical properties. The results are compared with the mechanical
properties obtained by previous workers. Experiments on cold
compression followed by aging of Cu-Ti alloys have indicated that
the most efficient hardening of the material results from continuous
precipitation of very fine particles within the matrix. These particles
were reported to be β`-type, Cu4Ti phase. The β`-β transformation
and particles coarsening within the matrix as well as long grain
boundaries were responsible for the overaging of Cu-1.5wt%Ti and
Cu-3.5wt%Ti alloys. It is well known that plate-like particles are β –
type, Cu3Ti phase. Discontinuous precipitation was found to start at
the grain boundaries and expand into grain interior. At the higher
aging temperature, a classic Widmanstätten morphology forms giving
rise to a coarse microstructure comprised of α and the equilibrium
phase β. Those results were confirmed by X-ray analysis, which
found that a few percent of Cu3Ti, β precipitates are formed during
aging at high temperature for long time for both Cu- Ti alloys (i.e.
Cu-1.5wt%Ti and Cu-3.5wt%Ti).
Abstract: Cloud computing has emerged as a promising
direction for cost efficient and reliable service delivery across data
communication networks. The dynamic location of service facilities
and the virtualization of hardware and software elements are stressing
the communication networks and protocols, especially when data
centres are interconnected through the internet. Although the
computing aspects of cloud technologies have been largely
investigated, lower attention has been devoted to the networking
services without involving IT operating overhead. Cloud computing
has enabled elastic and transparent access to infrastructure services
without involving IT operating overhead. Virtualization has been a
key enabler for cloud computing. While resource virtualization and
service abstraction have been widely investigated, networking in
cloud remains a difficult puzzle. Even though network has significant
role in facilitating hybrid cloud scenarios, it hasn't received much
attention in research community until recently. We propose Network
as a Service (NaaS), which forms the basis of unifying public and
private clouds. In this paper, we identify various challenges in
adoption of hybrid cloud. We discuss the design and implementation
of a cloud platform.
Abstract: Amoxicillin is an antibiotic which is widely used to
treat various infections in both human beings and animals. However,
when amoxicillin is released into the environment, it is a major
problem. Amoxicillin causes bacterial resistance to these drugs and
failure of treatment with antibiotics. Liquid membrane is of great
interest as a promising method for the separation and recovery of the
target ions from aqueous solutions due to the use of carriers for the
transport mechanism, resulting in highly selectivity and rapid
transportation of the desired metal ions. The simultaneous processes
of extraction and stripping in a single unit operation of liquid
membrane system are very interesting. Therefore, it is practical to
apply liquid membrane, particularly the HFSLM for industrial
applications as HFSLM is proved to be a separation process with
lower capital and operating costs, low energy and extractant with
long life time, high selectivity and high fluxes compared with solid
membranes. It is a simple design amenable to scaling up for industrial
applications. The extraction and recovery for (Amoxicillin) through
the hollow fiber supported liquid membrane (HFSLM) using
aliquat336 as a carrier were explored with the experimental data. The
important variables affecting on transport of amoxicillin viz.
extractant concentration and operating time were investigated. The
highest AMOX- extraction percentages of 85.35 and Amoxicillin
stripping of 80.04 were achieved with the best condition at 6 mmol/L
[aliquat336] and operating time 100 min. The extraction reaction
order (n) and the extraction reaction rate constant (kf) were found to
be 1.00 and 0.0344 min-1, respectively.
Abstract: Current systems complexity has reached a degree that
requires addressing conception and design issues while taking into
account environmental, operational, social, legal and financial
aspects. Therefore, one of the main challenges is the way complex
systems are specified and designed. The exponential growing effort,
cost and time investment of complex systems in modeling phase
emphasize the need for a paradigm, a framework and an environment
to handle the system model complexity. For that, it is necessary to
understand the expectations of the human user of the model and his
limits. This paper presents a generic framework for designing
complex systems, highlights the requirements a system model needs
to fulfill to meet human user expectations, and suggests a graphbased
formalism for modeling complex systems. Finally, a set of
transformations are defined to handle the model complexity.
Abstract: The goal of the paper is to highlight the effect of the
building design and epicentral distance on the storey lateral
displacements, for several reinforced concrete buildings (6, 9 and 12
stories). These structures are subjected to seismic accelerations from
the Boumerdes earthquake (Algeria, May 21st, Mw = 6.8). Using the
response spectrum method (modal spectral approach), the analysis is
performed in both longitudinal and transverse directions. The
building design is expressed through the fundamental period and
epicentral distance is used to represent the earthquake effect variation
on storey lateral displacements and interstory drift for the considered
buildings.
Abstract: Cyberspace has become a more viable arena for
budding artists to share musical acts through digital forms. The
increasing relevance of online communities has attracted scholars
from various fields demonstrating its influence on social capital. This
paper extends this understanding of social capital among Filipino
music artists belonging to the SoundCloud Philippines Facebook
Group.
The study makes use of various qualitative data obtained from
key-informant interviews and participant observation of online and
physical encounters, analyzed using the case study approach.
Soundcloud Philippines has over seven-hundred members and is
composed of Filipino singers, instrumentalists, composers, arrangers,
producers, multimedia artists and event managers. Group interactions
are a mix of online encounters based on Facebook and SoundCloud
and physical encounters through meet-ups and events. Benefits
reaped from the community are informational, technical,
instrumental, promotional, motivational and social support. Under the
guidance of online group administrators, collaborative activities such
as music productions, concerts and events transpire. Most conflicts
and problems arising are resolved peacefully. Social capital in
SoundCloud Philippines is mobilized through recognition, respect
and reciprocity.
Abstract: One of the functions of the commercial heavy vehicle
is to safely and efficiently transport goods and people. Due to its size
and carrying capacity, it is important to study the vehicle dynamic
stability during cornering. Study has shown that there are a number of
overloaded heavy vehicles or permissible Gross Vehicle Weight
(GVW) violations recorded at selected areas in Malaysia assigned by
its type and category. Thus, the objective of this study is to
investigate the correlation and effect of the GVW on heavy vehicle
stability during cornering event using simulation. Various selected
heavy vehicle types and category are simulated using IPG/Truck
Maker® with different GVW and road condition (coefficient of
friction of road surface), while the speed, driver characteristic, center
of gravity of load and road geometry are constant. Based on the
analysis, the relationship between GVW and lateral acceleration were
established. As expected, on the same value of coefficient of friction,
the maximum lateral acceleration would be increased as the GVW
increases.
Abstract: Remote arid areas of the vast expanses of the African
deserts hold huge subterranean reserves of brackish water resources
waiting for economic development. This work presents design
guidelines as well as initial performance data of new autonomous
solar desalination equipment which could help local communities
produce their own fresh water using solar energy only and, why not,
contribute to transforming desert lands into lush gardens. The output
of solar distillation equipments are typically low and in the range of 3
l/m2/day on the average. This new design with an integrated, water
based, environmentally-friendly solar heat storage system produced 5
l/m2/day in early spring weather. Equipment output during summer
exceeded 9 liters per m2 per day.
Abstract: Let us consider that the entire universe is composed of
a single hydrogen atom within which the electron is moving around
the proton. In this case, according to classical theories of physics,
radiation, photons respectively, should be absorbed by the electron.
Depending on the number of photons absorbed, the electron radius of
rotation around the proton is established. Until now, the principle of
photons absorption by electrons and the electron transition to a new
energy level, namely to a higher radius of rotation around the proton,
is not clarified in physics. This paper aims to demonstrate that
radiation, photons respectively, have mass and negative electrostatic
charge similar to electrons but infinitely smaller. The experiments
which demonstrate this theory are simple: thermal expansion,
photoelectric effect and thermonuclear reaction.
Abstract: This paper presents an application of Artificial Neural
Network (ANN) algorithm for improving power system voltage
stability. The training data is obtained by solving several normal and
abnormal conditions using the Linear Programming technique. The
selected objective function gives minimum deviation of the reactive
power control variables, which leads to the maximization of
minimum Eigen value of load flow Jacobian. The considered reactive
power control variables are switchable VAR compensators, OLTC
transformers and excitation of generators. The method has been
implemented on a modified IEEE 30-bus test system. The results
obtain from the test clearly show that the trained neural network is
capable of improving the voltage stability in power system with a
high level of precision and speed.
Abstract: Land Use Land Cover (LULC) changes due to human
activities and natural causes have become a major environmental
concern. Assessment of temporal remote sensing data provides
information about LULC impacts on environment. Land Surface
Temperature (LST) is one of the important components for modeling
environmental changes in climatological, hydrological, and
agricultural studies. In this study, LULC changes (September 7, 1984
and July 8, 2014) especially in agricultural lands together with
population changes (1985-2014) and LST status were investigated
using remotely sensed and census data in South Marmara Watershed,
Turkey. LULC changes were determined using Landsat TM and
Landsat OLI data acquired in 1984 and 2014 summers. Six-band TM
and OLI images were classified using supervised classification
method to prepare LULC map including five classes including Forest
(F), Grazing Land (G), Agricultural Land (A), Water Surface (W),
Residential Area-Bare Soil (R-B) classes. The LST image was also
derived from thermal bands of the same dates.
LULC classification results showed that forest areas, agricultural
lands, water surfaces and residential area-bare soils were increased as
65751 ha, 20163 ha, 1924 ha and 20462 ha respectively. In
comparison, a dramatic decrement occurred in grazing land (107985
ha) within three decades. The population increased 29% between
years 1984-2014 in whole study area. Along with the natural causes,
migration also caused this increase since the study area has an
important employment potential. LULC was transformed among the
classes due to the expansion in residential, commercial and industrial
areas as well as political decisions. In the study, results showed that
agricultural lands around the settlement areas transformed to
residential areas in 30 years.
The LST images showed that mean temperatures were ranged
between 26-32°C in 1984 and 27-33°C in 2014. Minimum
temperature of agricultural lands was increased 3°C and reached to
23°C. In contrast, maximum temperature of A class decreased to
41°C from 44°C. Considering temperatures of the 2014 R-B class and
1984 status of same areas, it was seen that mean, min and max
temperatures increased by 2°C.
As a result, the dynamism of population, LULC and LST resulted
in increasing mean and maximum surface temperatures, living
spaces/industrial areas and agricultural lands.
Abstract: Evapotranspiration is one of the most important
components of the hydrological cycle. Evapotranspiration (ETo) is an
important variable in water and energy balances on the earth’s
surface, and knowledge of the distribution of ET is a key factor in
hydrology, climatology, agronomy and ecology studies. Many
researchers have a valid relationship, which is a function of climate
factors, to estimate the potential evapotranspiration presented to the
plant water stress or water loss, prevent. The FAO-Penman method
(PM) had been recommended as a standard method. This method
requires many data and these data are not available in every area of
world. So, other methods should be evaluated for these conditions.
When sufficient or reliable data to solve the PM equation are not
available then Hargreaves equation can be used. The Hargreaves
equation (HG) requires only daily mean, maximum and minimum air
temperature extraterrestrial radiation .In this study, Hargreaves
method (HG) were evaluated in 12 stations in the North West region
of Iran. Results of HG and M.HG methods were compared with
results of PM method. Statistical analysis of this comparison showed
that calibration process has had significant effect on efficiency of
Hargreaves method.
Abstract: The use of hydroelectric pump-storage system at large
scale, MW-size systems, is already widespread around the world.
Designed for large scale applications, pump-storage station can be
scaled-down for small, remote residential applications. Given the cost
and complexity associated with installing a substation further than
100 miles from the main transmission lines, a remote, independent
and self-sufficient system is by far the most feasible solution. This
article is aiming at the design of wind and solar power generating
system, by means of pumped-storage to replace the wind and /or solar
power systems with a battery bank energy storage. Wind and solar
pumped-storage power generating system can reduce the cost of
power generation system, according to the user's electricity load and
resource condition and also can ensure system reliability of power
supply. Wind and solar pumped-storage power generation system is
well suited for remote residential applications with intermittent wind
and/or solar energy. This type of power systems, installed in these
locations, could be a very good alternative, with economic benefits
and positive social effects. The advantage of pumped storage power
system, where wind power regulation is calculated, shows that a
significant smoothing of the produced power is obtained, resulting in
a power-on-demand system’s capability, concomitant to extra
economic benefits.
Abstract: Implementation of advanced technologies requires
sophisticated instruments that deal with the operation, control,
restoration and protection of rapidly growing power system network
under normal and abnormal conditions. Presently, the applications of
Phasor Measurement Unit (PMU) are widely found in real time
operation, monitoring, controlling and analysis of power system
network as it eliminates the various limitations of supervisory control
and data acquisition system (SCADA) conventionally used in power
system. The use of PMU data is very rapidly increasing its
importance for online and offline analysis. Wide area measurement
system (WAMS) is developed as new technology by use of multiple
PMUs in power system. The present paper proposes a model of
Matlab based PMU using Discrete Fourier Transform (DFT)
algorithm and evaluation of its operation under different
contingencies. In this paper, PMU based two bus system having
WAMS network is presented as a case study.
Abstract: Today, there is a large number of political transcripts
available on the Web to be mined and used for statistical analysis,
and product recommendations. As the online political resources are
used for various purposes, automatically determining the political
orientation on these transcripts becomes crucial. The methodologies
used by machine learning algorithms to do an automatic classification
are based on different features that are classified under categories
such as Linguistic, Personality etc. Considering the ideological
differences between Liberals and Conservatives, in this paper, the
effect of Personality traits on political orientation classification is
studied. The experiments in this study were based on the correlation
between LIWC features and the BIG Five Personality traits. Several
experiments were conducted using Convote U.S. Congressional-
Speech dataset with seven benchmark classification algorithms. The
different methodologies were applied on several LIWC feature sets
that constituted by 8 to 64 varying number of features that are
correlated to five personality traits. As results of experiments,
Neuroticism trait was obtained to be the most differentiating
personality trait for classification of political orientation. At the same
time, it was observed that the personality trait based classification
methodology gives better and comparable results with the related
work.
Abstract: The new era of digital communication has brought up
many challenges that network operators need to overcome. The high
demand of mobile data rates require improved networks, which is a
challenge for the operators in terms of maintaining the quality of
experience (QoE) for their consumers. In live video transmission,
there is a sheer need for live surveillance of the videos in order to
maintain the quality of the network. For this purpose objective
algorithms are employed to monitor the quality of the videos that are
transmitted over a network. In order to test these objective algorithms,
subjective quality assessment of the streamed videos is required, as the
human eye is the best source of perceptual assessment. In this paper we
have conducted subjective evaluation of videos with varying spatial
and temporal impairments. These videos were impaired with frame
freezing distortions so that the impact of frame freezing on the quality
of experience could be studied. We present subjective Mean Opinion
Score (MOS) for these videos that can be used for fine tuning the
objective algorithms for video quality assessment.
Abstract: This paper presents a new automatic vehicle detection
method from very high resolution aerial images to measure traffic
density. The proposed method starts by extracting road regions from
image using road vector data. Then, the road image is divided into
equal sections considering resolution of the images. Gradient vectors
of the road image are computed from edge map of the corresponding
image. Gradient vectors on the each boundary of the sections are
divided where the gradient vectors significantly change their
directions. Finally, number of vehicles in each section is carried out
by calculating the standard deviation of the gradient vectors in each
group and accepting the group as vehicle that has standard deviation
above predefined threshold value. The proposed method was tested in
four very high resolution aerial images acquired from Istanbul,
Turkey which illustrate roads and vehicles with diverse
characteristics. The results show the reliability of the proposed
method in detecting vehicles by producing 86% overall F1 accuracy
value.
Abstract: Continuous upflow filters can combine the nutrient
(nitrogen and phosphate) and suspended solid removal in one unit
process. The contaminant removal could be achieved chemically or
biologically; in both processes the filter removal efficiency depends
on the interaction between the packed filter media and the influent. In
this paper a residence time distribution (RTD) study was carried out
to understand and compare the transfer behaviour of contaminants
through a selected filter media packed in a laboratory-scale
continuous up flow filter; the selected filter media are limestone and
white dolomite. The experimental work was conducted by injecting a
tracer (red drain dye tracer –RDD) into the filtration system and then
measuring the tracer concentration at the outflow as a function of
time; the tracer injection was applied at hydraulic loading rates
(HLRs) (3.8 to 15.2 m h-1). The results were analysed according to
the cumulative distribution function F(t) to estimate the residence
time of the tracer molecules inside the filter media. The mean
residence time (MRT) and variance σ2 are two moments of RTD that
were calculated to compare the RTD characteristics of limestone with
white dolomite. The results showed that the exit-age distribution of
the tracer looks better at HLRs (3.8 to 7.6 m h-1) and (3.8 m h-1) for
limestone and white dolomite respectively. At these HLRs the
cumulative distribution function F(t) revealed that the residence time
of the tracer inside the limestone was longer than in the white
dolomite; whereas all the tracer took 8 minutes to leave the white
dolomite at 3.8 m h-1. On the other hand, the same amount of the
tracer took 10 minutes to leave the limestone at the same HLR. In
conclusion, the determination of the optimal level of hydraulic
loading rate, which achieved the better influent distribution over the
filtration system, helps to identify the applicability of the material as
filter media. Further work will be applied to examine the efficiency
of the limestone and white dolomite for phosphate removal by
pumping a phosphate solution into the filter at HLRs (3.8 to 7.6 m h-1).
Abstract: In the field of fashion design, 3D Mannequin is a kind
of assisting tool which could rapidly realize the design concepts.
While the concept of 3D Mannequin is applied to the computer added
fashion design, it will connect with the development and the
application of design platform and system. Thus, the situation
mentioned above revealed a truth that it is very critical to develop a
module of 3D Mannequin which would correspond with the necessity
of fashion design. This research proposes a concrete plan that
developing and constructing a system of 3D Mannequin with Kinect.
In the content, ergonomic measurements of objective human features
could be attained real-time through the implement with depth camera
of Kinect, and then the mesh morphing can be implemented through
transformed the locations of the control-points on the model by
inputting those ergonomic data to get an exclusive 3D mannequin
model. In the proposed methodology, after the scanned points from the
Kinect are revised for accuracy and smoothening, a complete human
feature would be reconstructed by the ICP algorithm with the method
of image processing. Also, the objective human feature could be
recognized to analyze and get real measurements. Furthermore, the
data of ergonomic measurements could be applied to shape morphing
for the division of 3D Mannequin reconstructed by feature curves. Due
to a standardized and customer-oriented 3D Mannequin would be
generated by the implement of subdivision, the research could be
applied to the fashion design or the presentation and display of 3D
virtual clothes. In order to examine the practicality of research
structure, a system of 3D Mannequin would be constructed with JAVA
program in this study. Through the revision of experiments the
practicability-contained research result would come out.
Abstract: Diagnostic enzymes like aspartate aminotransferase
(AST), alanine aminotransferase (ALT) and alkaline phosphatase
(ALP) were determined as indices of heavy metal pollution in Tilapia
guinensis. Three different sets of fishes treated with lead (Pb), iron
(Fe) and copper (Cu) were used for the study while a fourth group
with no heavy metal served as a control. Fishes in each of the groups
were exposed to 2.65mg/l of Pb, 0.85mg/l of Fe and 0.35 mg/l of Cu
in aerated aquaria for 96 hours. Tissue fractionation of the liver
tissues was carried out and the three diagnostic enzymes (AST, ALT,
and ALP) were estimated. Serum levels of the same diagnostic
enzymes were also measured. The mean values of the serum enzyme
activity for ALP in each experimental group were 19.5±1.62,
29.67±2.17 and 1.15±0.27 IU/L for Pb, Fe and Cu groups compared
with 9.99±1.34 IU/L enzyme activity in the control. This result
showed that Pb and Fe caused increased release of the enzyme into
the blood circulation indicating increased tissue damage while Cu
caused a reduction in the serum level as compared with the level in
the control group. The mean values of enzyme activity obtained in
the liver were 102.14±6.12, 140.17±2.06 and 168.23±3.52 IU/L for
Pb, Fe and Cu groups, respectively compared to 91.20±9.42 IU/L
enzyme activity for the control group. The serum and liver AST and
ALT activities obtained in Pb, Fe, Cu and control groups are
reported. It was generally noted that the presence of the heavy metal
caused liver tissues damage and consequent increased level of the
diagnostic enzymes in the serum.