Abstract: Nonlinear evolution of broadband ultrasonic pulses
passed through the rock specimens is studied using the apparatus
“GEOSCAN-02M”. Ultrasonic pulses are excited by the pulses of Qswitched
Nd:YAG laser with the time duration of 10 ns and with the
energy of 260 mJ. This energy can be reduced to 20 mJ by some light
filters. The laser beam radius did not exceed 5 mm. As a result of the
absorption of the laser pulse in the special material – the optoacoustic
generator–the pulses of longitudinal ultrasonic waves are excited with
the time duration of 100 ns and with the maximum pressure
amplitude of 10 MPa. The immersion technique is used to measure
the parameters of these ultrasonic pulses passed through a specimen,
the immersion liquid is distilled water. The reference pulse passed
through the cell with water has the compression and the rarefaction
phases. The amplitude of the rarefaction phase is five times lower
than that of the compression phase. The spectral range of the
reference pulse reaches 10 MHz. The cubic-shaped specimens of the
Karelian gabbro are studied with the rib length 3 cm. The ultimate
strength of the specimens by the uniaxial compression is (300±10)
MPa. As the reference pulse passes through the area of the specimen
without cracks the compression phase decreases and the rarefaction
one increases due to diffraction and scattering of ultrasound, so the
ratio of these phases becomes 2.3:1. After preloading some horizontal
cracks appear in the specimens. Their location is found by one-sided
scanning of the specimen using the backward mode detection of the
ultrasonic pulses reflected from the structure defects. Using the
computer processing of these signals the images are obtained of the
cross-sections of the specimens with cracks. By the increase of the
reference pulse amplitude from 0.1 MPa to 5 MPa the nonlinear
transformation of the ultrasonic pulse passed through the specimen
with horizontal cracks results in the decrease by 2.5 times of the
amplitude of the rarefaction phase and in the increase of its duration
by 2.1 times. By the increase of the reference pulse amplitude from 5
MPa to 10 MPa the time splitting of the phases is observed for the
bipolar pulse passed through the specimen. The compression and
rarefaction phases propagate with different velocities. These features
of the powerful broadband ultrasonic pulses passed through the rock
specimens can be described by the hysteresis model of Preisach-
Mayergoyz and can be used for the location of cracks in the optically
opaque materials.
Abstract: Research has shown that techno-entrepreneurship is
economically significant. Therefore, it is suggested that teaching
techno-entrepreneurship may be important because such programmes
would prepare current and future generations of learners to recognise
and act on high-technology opportunities. Education in technoentrepreneurship
may increase the knowledge of how to start one’s
own enterprise and recognise the technological opportunities for
commercialisation to improve decision-making about starting a new
venture; also it influence decisions about capturing the business
opportunities and turning them into successful ventures. Universities
can play a main role in connecting and networking technoentrepreneurship
students towards a cooperative attitude with real
business practice and industry knowledge. To investigate and answer
whether education for techno-entrepreneurs really helps, this paper
choses a comparison of literature reviews as its method of research.
After reviewing literature related to the impact of technoentrepreneurship
education on self-employment 6 studies which had
similar aim and objective to this paper were. These particular papers
were selected based on a keywords search and as their aim,
objectives, and gaps were close to the current research. In addition,
they were all based on the influence of techno-entrepreneurship
education in self-employment and intention of students to start new
ventures. The findings showed that teaching techno-entrepreneurship
education may have an influence on students’ intention and their
future self-employment, but which courses should be covered and the
duration of programmes, needs further investigation.
Abstract: Ocean current is always available around the
surrounding of SHELL Sabah Water Platform and data are collected
every 10 minutes, 24 hours a day, for a period of 365 days. Due to
low current speed, conventional hydrokinetic power generation is not
feasible, thus leading to the study of low current enabled vortex
induced vibration power generation application. In this case, the
design of a vortex induced vibration application is studied to obtain
an optimum design for the VIV oscillator. Power output is then
determined to study the feasibility of the VIV application in low
current condition.
Abstract: This paper studies a mathematical model based on the
integral equations for dynamic analyzes numerical investigations of a
non-uniform or multi-material composite beam. The beam is
subjected to a sub-tangential follower force and elastic foundation.
The boundary conditions are represented by generalized
parameterized fixations by the linear and rotary springs. A
mathematical formula based on Euler-Bernoulli beam theory is
presented for beams with variable cross-sections. The non-uniform
section introduces non-uniformity in the rigidity and inertia of beams
and consequently, more complicated equilibrium who governs the
equation. Using the boundary element method and radial basis
functions, the equation of motion is reduced to an algebro-differential
system related to internal and boundary unknowns. A generalized
formula for the deflection, the slope, the moment and the shear force
are presented. The free vibration of non-uniform loaded beams is
formulated in a compact matrix form and all needed matrices are
explicitly given. The dynamic stability analysis of slender beam is
illustrated numerically based on the coalescence criterion. A realistic
case related to an industrial chimney is investigated.
Abstract: Carbon nanotubes (CNTs) are known for having high elastic properties with high surface area that promote them as good candidates for reinforcing polymeric matrices. In composite materials, CNTs lack chemical bonding with the surrounding matrix which decreases the possibility of better stress transfer between the components. In this work, a chemical treatment for activating the surface of the multi-wall carbon nanotubes (MWCNT) was applied and the effect of this functionalization on the elastic properties of the epoxy nanocomposites was studied. Functional amino-groups were added to the surface of the CNTs and it was evaluated to be about 34% of the total weight of the CNTs. Elastic modulus was found to increase by about 40% of the neat epoxy resin at CNTs’ weight fraction of 0.5%. The elastic modulus was found to decrease after reaching a certain concentration of CNTs which was found to be 1% wt. The scanning electron microscopic pictures showed the effect of the CNTs on the crack propagation through the sample by forming stress concentrated spots at the nanocomposite samples.
Abstract: In this paper, we describe the use of formal methods
to model malware behaviour. The modelling of harmful behaviour
rests upon syntactic structures that represent malicious procedures
inside malware. The malicious activities are modelled by a formal
grammar, where API calls’ components are the terminals and the set
of API calls used in combination to achieve a goal are designated
non-terminals. The combination of different non-terminals in various
ways and tiers make up the attack vectors that are used by harmful
software. Based on these syntactic structures a parser can be
generated which takes execution traces as input for pattern
recognition.
Abstract: The current-voltage (I-V) characteristics of Pd/n-GaN Schottky barrier were studied at temperatures over room temperature (300-470K). The values of ideality factor (n), zero-bias barrier height (φB0), flat barrier height (φBF) and series resistance (Rs) obtained from I-V-T measurements were found to be strongly temperature dependent while (φBo) increase, (n), (φBF) and (Rs) decrease with increasing temperature. The apparent Richardson constant was found to be 2.1x10-9 Acm-2K-2 and mean barrier height of 0.19 eV. After barrier height inhomogeneities correction, by assuming a Gaussian distribution (GD) of the barrier heights, the Richardson constant and the mean barrier height were obtained as 23 Acm-2K-2 and 1.78eV, respectively. The corrected Richardson constant was very closer to theoretical value of 26 Acm-2K-2.
Abstract: Target of this study was the analysis of the impact of
crude glycerol on canine spermatozoa motility, morphology,
viability, and membrane integrity. Experiments were realized in vitro.
In the study, semen from 5 large dog breeds was used. They were
typical representatives of large breeds, coming from healthy rearing,
regularly vaccinated and integrated to the further breeding. Semen
collections were realized at the owners of animals and in the
veterinary clinic. Subsequently the experiments were realized at the
Department of Animal Physiology of the SUA in Nitra. The
spermatozoa motility was evaluated using CASA analyzer
(SpermVisionTM, Minitub, Germany) at the temperature 5 and 37°C
for 5 hours. In the study, 13 motility parameters were evaluated.
Generally, crude glycerol has generally negative effect on
spermatozoa motility. Morphological analysis was realized using
Hancock staining and the preparations were evaluated at
magnification 1000x using classification tables of morphologically
changed spermatozoa. Data clearly detected the highest number of
morphologically changed spermatozoa in the experimental groups
(know twisted tails, tail torso and tail coiling). For acrosome
alterations swelled acrosomes, removed acrosomes and acrosomes
with undulated membrane were detected. In this study also the effect
of crude glycerol on spermatozoa membrane integrity were analyzed.
The highest crude glycerol concentration significantly affects
spermatozoa integrity. Results of this study show that crude glycerol
has effect of spermatozoa motility, viability, and membrane integrity.
Detected changes are related to crude glycerol concentration,
temperature, as well as time of incubation.
Abstract: Predicting earnings management is vital for the capital
market participants, financial analysts and managers. The aim of this
research is attempting to respond to this query: Is there a significant
difference between the regression model and neural networks’
models in predicting earnings management, and which one leads to a
superior prediction of it? In approaching this question, a Linear
Regression (LR) model was compared with two neural networks
including Multi-Layer Perceptron (MLP), and Generalized
Regression Neural Network (GRNN). The population of this study
includes 94 listed companies in Tehran Stock Exchange (TSE)
market from 2003 to 2011. After the results of all models were
acquired, ANOVA was exerted to test the hypotheses. In general, the
summary of statistical results showed that the precision of GRNN did
not exhibit a significant difference in comparison with MLP. In
addition, the mean square error of the MLP and GRNN showed a
significant difference with the multi variable LR model. These
findings support the notion of nonlinear behavior of the earnings
management. Therefore, it is more appropriate for capital market
participants to analyze earnings management based upon neural
networks techniques, and not to adopt linear regression models.
Abstract: In this numerical work, mixed convection and entropy
generation of Cu–water nanofluid in a lid-driven square cavity have
been investigated numerically using the Lattice Boltzmann Method.
Horizontal walls of the cavity are adiabatic and vertical walls have
constant temperature but different values. The top wall has been
considered as moving from left to right at a constant speed, U0. The
effects of different parameters such as nanoparticle volume
concentration (0–0.05), Rayleigh number (104–106) and Reynolds
numbers (1, 10 and 100) on the entropy generation, flow and
temperature fields are studied. The results have shown that addition
of nanoparticles to the base fluid affects the entropy generation, flow
pattern and thermal behavior especially at higher Rayleigh and low
Reynolds numbers. For pure fluid as well as nanofluid, the increase
of Reynolds number increases the average Nusselt number and the
total entropy generation, linearly. The maximum entropy generation
occurs in nanofluid at low Rayleigh number and at high Reynolds
number. The minimum entropy generation occurs in pure fluid at low
Rayleigh and Reynolds numbers. Also at higher Reynolds number,
the effect of Cu nanoparticles on enhancement of heat transfer was
decreased because the effect of lid-driven cavity was increased. The
present results are validated by favorable comparisons with
previously published results. The results of the problem are presented
in graphical and tabular forms and discussed.
Abstract: There are real needs to integrate types of Open
Educational Resources (OER) with an intelligent system to extract
information and knowledge in the semantic searching level. The
needs came because most of current learning standard adopted web
based learning and the e-learning systems do not always serve all
educational goals. Semantic Web systems provide educators,
students, and researchers with intelligent queries based on a semantic
knowledge management learning system. An ontology-based learning
system is an advanced system, where ontology plays the core of the
semantic web in a smart learning environment. The objective of this
paper is to discuss the potentials of ontologies and mapping different
kinds of ontologies; heterogeneous or homogenous to manage and
control different types of Open Educational Resources. The important
contribution of this research is that it uses logical rules and
conceptual relations to map between ontologies of different
educational resources. We expect from this methodology to establish
an intelligent educational system supporting student tutoring, self and
lifelong learning system.
Abstract: In recent years, new techniques for solving complex
problems in engineering are proposed. One of these techniques is
JPSO algorithm. With innovative changes in the nature of the jump
algorithm JPSO, it is possible to construct a graph-based solution
with a new algorithm called G-JPSO. In this paper, a new algorithm
to solve the optimal control problem Fletcher-Powell and optimal
control of pumps in water distribution network was evaluated.
Optimal control of pumps comprise of optimum timetable operation
(status on and off) for each of the pumps at the desired time interval.
Maximum number of status on and off for each pumps imposed to the
objective function as another constraint. To determine the optimal
operation of pumps, a model-based optimization-simulation
algorithm was developed based on G-JPSO and JPSO algorithms.
The proposed algorithm results were compared well with the ant
colony algorithm, genetic and JPSO results. This shows the
robustness of proposed algorithm in finding near optimum solutions
with reasonable computational cost.
Abstract: This paper proposes a novel heuristic algorithm that aims to determine the best size and location of distributed generators in unbalanced distribution networks. The proposed heuristic algorithm can deal with the planning cases where power loss is to be optimized without violating the system practical constraints. The distributed generation units in the proposed algorithm is modeled as voltage controlled node with the flexibility to be converted to constant power factor node in case of reactive power limit violation. The proposed algorithm is implemented in MATLAB and tested on the IEEE 37 -node feeder. The results obtained show the effectiveness of the proposed algorithm.
Abstract: Tannins are a unique category of plant phytochemicals
especially in terms of their vast potential health-benefiting properties.
Researchers have described the capacity of tannins to enhance
glucose uptake and inhibit adipogenesis, thus being potential drugs
for the treatment of non-insulin dependent diabetes mellitus. Thus,
the present research was conducted to find out tannin content of food
products. The percentage of tannin in various analyzed sources
ranged from 0.0 to 108.53%; highest in kathaa and lowest in ker and
mango bark. The percentage of tannins present in the plants,
however, varies. Numerous studies have confirmed that the naturally
occurring polyphenols are key factor for the beneficial effects of the
herbal medicines. Isolation and identification of active constituents
from plants, preparation of standardized dose & dosage regimen can
play a significant role in improving the hypoglycaemic action.
Abstract: The latest years the number of immigrants at Greece
has increased dramatically. Their impact on the National Health
System (NHS) has not been yet thoroughly investigated. This paper
analyses the cost of immigrants to the NHS hospitals of the region of
Eastern Macedonia and Thrace. The data are collected from 2005 to
2011 from five different hospitals and are analysed using linear
mixed effects models in order to investigate the effects of nationality
and year on the cost of hospitalization and treatment. The results
show that generally the Greek nationality patients have a higher mean
cost of hospitalization compared to the immigrants and that there is
an increasing trend for the cost except for the year 2010.
Abstract: The consumption of food contaminated with molds
(microscopic filamentous fungi) and their toxic metabolites results in
the development of food-borne mycotoxicosis. The spores of molds
are ubiquitously spread in the environment and can be detected
everywhere. Ochratoxin A is a toxic and potentially carcinogenic
fungal toxin found in a variety of food commodities. In this study, the
mycological quality of various ready-to-eat local and imported pork
meat and meat byproducts sold in Egyptian markets were assessed
and the presence of various molds was determined in pork used as a
raw material, edible organs as liver and kidney as well as in
fermented raw meat by-products. The study assessed the mycological
quality of pork raw meat and their by-products sold in commercial
shops in Cairo, Egypt. Mycological analysis was conducted on
(n=110) samples which included pig’s livers and kidneys from
Egyptian Bassatin slaughter house; local and imported processed
pork meat by-products from Egyptian pork markets. The isolates
were identified using traditional mycological and biochemical tests.
All kidney and liver samples were positive to molds growth while all
byproducts were negative. Ochratoxin A levels were quantitatively
analyzed using the high performance liquid chromatography (HPLC)
and the highest results were present in kidney 7.51 part per billion
(ppb) followed by minced meat 6.19 ppb generally the local samples
showed higher levels than the imported ones. To the best of our
knowledge, this is the first report on mycotoxins detection and
quantification from pork by-products in Egypt.
Abstract: The level and type of student academic motivation are
the key factors in their development and determine the effectiveness
of their education. Improving motivation is very important with
regard to courses on middle school mathematics. This article examines the general position regarding the practice of
academic motivation. It also examines the particular features of
mathematical problem solving in a school setting.
Abstract: Academic libraries in Malaysia are still not prepared
for disaster even though several occasions have been reported. The
study sets out to assess the current status of preparedness in disaster
management among Malaysian academic libraries in the State of
Selangor and the Federal Territory of Kuala Lumpur. To obtain a
base level of knowledge on disaster preparedness of current practices,
a questionnaire was distributed to chief librarians or their assignees in
charge of disaster or emergency preparedness at 40 academic
libraries and 34 responses were received. The study revolved around
the current status of preparedness, on various issues including
existence of disaster preparedness plan among academic libraries in
Malaysia, disaster experiences by the academic libraries, funding,
risk assessment activities and involvement of library staff in disaster
management. Frequency and percentage tables were used in the
analysis of the data collected. Some of the academic libraries under
study have experienced one form of disaster or the other. Most of the
academic libraries do not have a written disaster preparedness plan.
The risk assessments and staff involvement in disaster preparedness
by these libraries were generally adequate.
Abstract: This paper illustrates the background of various
concepts, approaches, terminologies used to describe the basic
framework of an Islamic Hotel Room design. This paper reviews the
theoretical views in establishing a suitable and optimum environment
for Muslim as well as non-Muslim guests in hotel rooms while
according to shariah. It involves a few research methodologies that
requires the researcher to study on a few characteristics needed to
create more efficient rooms in terms of social interaction, economic
growth and other tolerable elements. This paper intends on revealing
the elements that are vital and may contribute for hotels in achieving
a more conclusive research on space planning for hotel rooms
focusing on the shariah and Muslim guests. Malaysia is an Islamic
country and has billion of tourists coming over for business and
recreational purposes. Therefore, having a righteous environment that
best suit this target user is important in terms of generating the
economy as well as providing a better understanding to the
community on the benefits of applying these qualities in a
conventional resort design.
Abstract: Massive rock avalanches formed some of the largest landslide deposits on Earth and they represent one of the major geohazards in high-relief mountains. This paper interprets a very large sedimentary fan (the Sernio fan, Valtellina, Northern Italy), located 20 Km SW from Val Pola Rock avalanche (1987), as the deposit of a partial collapse of a Deep Seated Gravitational Slope Deformation (DSGSD), afterwards eroded and buried by debris flows. The proposed emplacement sequence has been reconstructed based on geomorphological, structural and mechanical evidences. The Sernio fan is actually considered anomalous with reference to the very high ratio between the fan area (≈ 4.5km2) and the basin area (≈ 3km2). The morphology of the fan area is characterised by steep slopes (dip ≈ 20%) and the fan apex is extended for 1.8 km inside the small catchment basin. This sedimentary fan was originated by a landslide that interested a part of a large deep-seated gravitational slope deformation, involving a wide area of about 55 km². The main controlling factor is tectonic and it is related to the proximity to regional fault systems and the consequent occurrence of fault weak rocks (GSI locally lower than 10 with compressive stress lower than 20MPa). Moreover, the fan deposit shows sedimentary evidences of recent debris flow events. The best current explanation of the Sernio fan involves an initial failure of some hundreds of Mm3. The run-out was quite limited because of the morphology of Valtellina’s valley floor, and the deposit filled the main valley forming a landslide dam, as confirmed by the lacustrine deposits detected upstream the fan. Nowadays the debris flow events represent the main hazard in the study area.