Abstract: In contrast to conventional generators, self-excited induction generators are found to be most suitable machines for wind energy conversion in remote and windy areas due to many advantages over grid connected machines. This papers presents a Self-Excited Induction Generator (SEIG) driven by wind turbine and supplying an induction motor which is coupled to a centrifugal pump. A method to describe the steady state performance based on nodal analysis is presented. Therefore the advanced knowledge of the minimum excitation capacitor value is required. The effects of variation of excitation capacitance on system and rotor speed under different loading conditions have been analyzed and considered to optimize induction motor pump performances.
Abstract: In this paper, FinFET devices are analyzed with
emphasis on sub-threshold leakage current control. This is achieved
through proper biasing of the back gate, and through the use of
asymmetric work functions for the four terminal FinFET devices. We
are also examining different configurations of multiplexers and XOR
gates using transistors of symmetric and asymmetric work functions.
Based on extensive characterization data for MUX circuits, our
proposed configuration using symmetric devices lead to leakage
current and delay improvements of 65% and 47% respectively
compared to results in the literature. For XOR gates, a 90%
improvement in the average leakage current is achieved by using
asymmetric devices. All simulations are based on a 25nm FinFET
technology using the University of Florida UFDG model.
Abstract: The number of the companies accepting RFID in Korea
has been increased continuously due to the domestic development of
information technology. The acceptance of RFID by companies in
Korea enabled them to do business with many global enterprises in a
much more efficient and effective way. According to a survey[33,
p76], many companies in Korea have used RFID for inventory or
distribution manages. But, the use of RFID in the companies in Korea
is in the early stages and its potential value hasn-t fully been realized
yet. At this time, it would be very important to investigate the factors
that affect RFID acceptance. For this study, many previous studies
were referenced and some RFID experts were interviewed. Through
the pilot test, four factors were selected - Security Trust, Employee
Knowledge, Partner Influence, Service Provider Trust - affecting
RFID acceptance and an extended technology acceptance
model(e-TAM) was presented with those factors. The proposed model
was empirically tested using data collected from employees in
companies or public enterprises. In order to analyze some
relationships between exogenous variables and four variables in TAM,
structural equation modeling(SEM) was developed and SPSS12.0 and
AMOS 7.0 were used for analyses. The results are summarized as
follows: 1) security trust perceived by employees positively
influences on perceived usefulness and perceived ease of use; 2)
employee-s knowledge on RFID positively influences on only
perceived ease of use; 3) a partner-s influence for RFID acceptance
positively influences on only perceived usefulness; 4) service provider
trust very positively influences on perceived usefulness and perceived
ease of use 5) the relationships between TAM variables are the same as
the previous studies.
Abstract: P16/INK4A is tumor suppressor protein that plays a critical role in cell cycle regulation. Loss of P16 protein expression has been implicated in pathogenesis of many cancers, including lymphoma. Therefore, we sought to investigate if loss of P16 protein expression is associated with lymphoma and/or any specific lymphoma subtypes (Hodgkin-s lymphoma (HL) and nonHodgkin-s lymphoma (NHL)). Fifty-five lymphoma cases consisted of 30 cases of HL and 25 cases of NHL, with an age range of 3 to 78 years, were examined for loss of P16 by immunohistochemical technique using a specific antibody reacting against P16. In total, P16 loss was seen in 33% of all lymphoma cases. P16 loss was identified in 47.7% of HL cases. In contrast, only 16% of NHL showed loss of P16. Loss of P16 was seen in 67% of HL patients with 50 years of age or older, whereas P16 loss was found in only 42% of HL patients with less than 50 years of age. P16 loss in HL is somewhat higher in male (55%) than in female (30%). In subtypes of HL, P16 loss was found exclusively in all cases of lymphocyte depletion, lymphocyte predominance and unclassified cases, whereas P16 loss was seen in 39% of mixed cellularity and 29% of nodular sclerosis cases. In low grade NHL patients, P16 loss was seen in approximately one-third of cases, whereas no or very rare of P16 loss was found in intermediate and high grade cases. P16 loss did not show any correlation with age or gender of NHL patients. In conclusion, the high rate of P16 loss seen in our study suggests that loss of P16 expression plays a critical role in the pathogenesis of lymphoma, particularly with HL.
Abstract: Nodes in mobile Ad Hoc Network (MANET) do not
rely on a central infrastructure but relay packets originated by other
nodes. Mobile ad hoc networks can work properly only if the
participating nodes collaborate in routing and forwarding. For
individual nodes it might be advantageous not to collaborate, though.
In this conceptual paper we propose a new approach based on
relationship among the nodes which makes them to cooperate in an
Adhoc environment. The trust unit is used to calculate the trust
values of each node in the network. The calculated trust values are
being used by the relationship estimator to determine the relationship
status of nodes. The proposed enhanced protocol was compared with
the standard DSR protocol and the results are analyzed using the
network simulator-2.
Abstract: Work-life balance has been acknowledged and
promoted for the sake of employee retention. It is essential for a
manager to realize the human resources situation within a company to
help employees work happily and perform at their best. This paper
suggests knowledge management and critical thinking are useful to
motivate employees to think about their work-life balance. A
qualitative case study is presented, which aimed to discover the
meaning of work-life balance-s meaning from the perspective of Thai
knowledge workers and how it affects their decision-making towards
work resignation. Results found three types of work-life balance
dimensions; a work- life balance including a workplace and a private
life setting, an organizational working life balance only, and a worklife
balance only in a private life setting. These aspects all influenced
the decision-making of the employees. Factors within a theme of an
organizational work-life balance were involved with systematic
administration, fair treatment, employee recognition, challenging
assignments to gain working experience, assignment engagement,
teamwork, relationship with superiors, and working environment,
while factors concerning private life settings were about personal
demands such as an increasing their salary or starting their own
business.
Abstract: In this contribution, a way to enhance the performance of the classic Genetic Algorithm is proposed. The idea of restarting a Genetic Algorithm is applied in order to obtain better knowledge of the solution space of the problem. A new operator of 'insertion' is introduced so as to exploit (utilize) the information that has already been collected before the restarting procedure. Finally, numerical experiments comparing the performance of the classic Genetic Algorithm and the Genetic Algorithm with restartings, for some well known test functions, are given.
Abstract: In this article the influence of higher frequency effects
in addition to a special damper design on the electrical behavior of a
synchronous generator main exciter machine is investigated. On the
one hand these machines are often highly stressed by harmonics from
the bridge rectifier thus facing additional eddy current losses. On the
other hand the switching may cause the excitation of dangerous
voltage peaks in resonant circuits formed by the diodes of the
rectifier and the commutation reactance of the machine. Therefore
modern rotating exciters are treated like synchronous generators
usually modeled with a second order equivalent circuit. Hence the
well known Standstill Frequency Response Test (SSFR) method is
applied to a test machine in order to determine parameters for the
simulation. With these results it is clearly shown that higher
frequencies have a strong impact on the conventional equivalent
circuit model. Because of increasing field displacement effects in the
stranded armature winding the sub-transient reactance is even smaller
than the armature leakage at high frequencies. As a matter of fact this
prevents the algorithm to find an equivalent scheme. This issue is
finally solved using Laplace transfer functions fully describing the
transient behavior at the model ports.
Abstract: Nowadays, ontologies are the only widely accepted paradigm for the management of sharable and reusable knowledge in a way that allows its automatic interpretation. They are collaboratively created across the Web and used to index, search and annotate documents. The vast majority of the ontology based approaches, however, focus on indexing texts at document level. Recently, with the advances in ontological engineering, it became clear that information indexing can largely benefit from the use of general purpose ontologies which aid the indexing of documents at word level. This paper presents a concept indexing algorithm, which adds ontology information to words and phrases and allows full text to be searched, browsed and analyzed at different levels of abstraction. This algorithm uses a general purpose ontology, OntoRo, and an ontologically tagged corpus, OntoCorp, both developed for the purpose of this research. OntoRo and OntoCorp are used in a two-stage supervised machine learning process aimed at generating ontology tagging rules. The first experimental tests show a tagging accuracy of 78.91% which is encouraging in terms of the further improvement of the algorithm.
Abstract: Previous studies on political budget cycles (PBCs)
implicitly assume the executive has full discretion power over fiscal
policy, neglecting the role of checks and balances of the legislature.
This paper goes beyond traditional PBCs models and sheds light on
the case study of Japan, South Korea, and Taiwan over the 1988-2007
periods. Based on the results, we find no evidence of electoral impacts
on the public expenditures in South Korean and Taiwan's
congressional elections. We also noted that PBCs are found on
Taiwan-s government expenditures during our sample periods.
Furthermore, the results also show that Japan-s legislature has a
significant checks and balances on government-s expenditures.
However, empirical results show that the legislature veto player in
Taiwan neither has effect on the reduction of public expenditures, nor
has the moderating effect over Taiwan-s political budget cycles, albeit
that they are statistically insignificant.We suggest that the existence of
PBCs in Taiwan is due to a weaker systemof checks and balances. Our
conjecture is that Taiwan either has no legislative veto player or has
observed low compliance to the law during the time period examined
in our study.
Abstract: One of the robust fault detection filter (RFDF)
designing method is based on sliding-mode theory. The main purpose
of our study is to introduce an innovative simplified reference
residual model generator to formulate the RFDF as a sliding-mode
observer without any manipulation package or transformation matrix,
through which the generated residual signals can be evaluated. So the
proposed design is more explicit and requires less design parameters
in comparison with approaches requiring changing coordinates. To
the best author's knowledge, this is the first time that the sliding
mode technique is applied to detect actuator and sensor faults in a
real boiler. The designing procedure is proposed in a drum boiler in
Synvendska Kraft AB Plant in Malmo, Sweden as a multivariable
and strongly coupled system. It is demonstrated that both sensor and
actuator faults can robustly be detected. Also sensor faults can be
diagnosed and isolated through this method.
Abstract: This paper presents the doping profile measurement
and characterization technique for the pocket implanted nano scale
n-MOSFET. Scanning capacitance microscopy and atomic force
microscopy have been used to image the extent of lateral dopant
diffusion in MOS structures. The data are capacitance vs. voltage
measurements made on a nano scale device. The technique is nondestructive
when imaging uncleaved samples. Experimental data from
the published literature are presented here on actual, cleaved device
structures which clearly indicate the two-dimensional dopant profile
in terms of a spatially varying modulated capacitance signal. Firstorder
deconvolution indicates the technique has much promise for
the quantitative characterization of lateral dopant profiles. The pocket
profile is modeled assuming the linear pocket profiles at the source
and drain edges. From the model, the effective doping concentration
is found to use in modeling and simulation results of the various
parameters of the pocket implanted nano scale n-MOSFET. The
potential of the technique to characterize important device related
phenomena on a local scale is also discussed.
Abstract: This paper presents a new technique for detection of
human faces within color images. The approach relies on image
segmentation based on skin color, features extracted from the two-dimensional
discrete cosine transform (DCT), and self-organizing
maps (SOM). After candidate skin regions are extracted, feature
vectors are constructed using DCT coefficients computed from those
regions. A supervised SOM training session is used to cluster feature
vectors into groups, and to assign “face" or “non-face" labels to those
clusters. Evaluation was performed using a new image database of
286 images, containing 1027 faces. After training, our detection
technique achieved a detection rate of 77.94% during subsequent
tests, with a false positive rate of 5.14%. To our knowledge, the
proposed technique is the first to combine DCT-based feature
extraction with a SOM for detecting human faces within color
images. It is also one of a few attempts to combine a feature-invariant
approach, such as color-based skin segmentation, together with
appearance-based face detection. The main advantage of the new
technique is its low computational requirements, in terms of both
processing speed and memory utilization.
Abstract: This paper presents an integrated model that
automatically measures the change of rivers, damage area of bridge
surroundings, and change of vegetation. The proposed model is on the
basis of a neurofuzzy mechanism enhanced by SOM optimization
algorithm, and also includes three functions to deal with river imagery.
High resolution imagery from FORMOSAT-2 satellite taken before
and after the invasion period is adopted. By randomly selecting a
bridge out of 129 destroyed bridges, the recognition results show that
the average width has increased 66%. The ruined segment of the
bridge is located exactly at the most scour region. The vegetation
coverage has also reduced to nearly 90% of the original. The results
yielded from the proposed model demonstrate a pinpoint accuracy rate
at 99.94%. This study brings up a successful tool not only for
large-scale damage assessment but for precise measurement to
disasters.
Abstract: This paper presents an experimental investigation on
the machinability of laser-sintered material using small ball end mill focusing on wear mechanisms. Laser-sintered material was produced
by irradiating a laser beam on a layer of loose fine SCM-Ni-Cu powder. Bulk carbon steel JIS S55C was selected as a reference steel.
The effects of powder consolidation mechanisms and unsintered
powder on the tool life and wear mechanisms were carried out. Results indicated that tool life in cutting laser-sintered material is
lower than that in cutting JIS S55C. Adhesion of the work material and chipping were the main wear mechanisms of the ball end mill in
cutting laser-sintered material. Cutting with the unsintered powder
surrounding the tool and laser-sintered material had caused major fracture on the cutting edge.
Abstract: Leave of absence is important in maintaining a good
status of human resource quality. Allowing the employees temporarily
free from the routine assignments can vitalize the workers- morality
and productivity. This is particularly critical to secure a satisfactory
service quality for healthcare professionals of which were typically
featured with labor intensive and complicated works to perform. As
one of the veteran hospitals that were found and operated by the
Veteran Department of Taiwan, the nursing staff of the case hospital
was squeezed to an extreme minimum level under the pressure of a
tight budgeting. Leave of absence on schedule became extremely
difficult, especially for the intensive care units (ICU), in which
required close monitoring over the cared patients, and that had more
easily driven the ICU nurses nervous. Even worse, the deferred leaves
were more than 10 days at any time in the ICU because of a fluctuating
occupancy. As a result, these had brought a bad setback to this
particular nursing team, and consequently defeated the job
performance and service quality. To solve this problem and
accordingly to strengthen their morality, a project team was organized
across different departments specific for this. Sufficient information
regarding jobs and positions requirements, labor resources, and actual
working hours in detail were collected and analyzed in the team
meetings. Several alternatives were finalized. These included job
rotating, job combination, leave on impromptu and cross-departmental
redeployment. Consequently, the deferred leave days sharply reduced
70% to a level of 3 or less days. This improvement had not only
provided good shelter for the ICU nurses that improved their job
performance and patient safety but also encouraged the nurses active
participating of a project and learned the skills of solving problems
with colleagues.
Abstract: Since the beginning of human history, human
activities have caused many changes in the environment. Today, a
particular attention should be paid to gaining knowledge about water
quality of wetlands which are pristine natural environments rich in
genetic reserves. If qualitative conditions of industrial areas (in terms
of both physicochemical and biological conditions) are not addressed
properly, they could cause disruption in natural ecosystems,
especially in rivers. With regards to the quality of water resources,
determination of pollutant sources plays a pivotal role in engineering
projects as well as designing water quality control systems. Thus,
using different methods such as flow duration curves, dischargepollution
load model and frequency analysis by HYFA software
package, risk of various industrial pollutants in international and
ecologically important Gavkhoni wetland is analyzed. In this study, a
station located at Varzaneh City is used as the last station on
Zayanderud River, from where the river water is discharged into the
wetland. Results showed that elements- concentrations often
exceeded the allowed level and river water can endanger regional
ecosystem. In addition, if the river discharge is managed on Q25
basis, this basis can lower concentrations of elements, keeping them
within the normal level.
Abstract: This paper deals with the problem of thermal and
mechanical shocks, which rising during operation, mostly at
interrupted cut. Here will be solved their impact on the cutting edge
tool life, the impact of coating technology on resistance to shocks
and experimental determination of tool life in heating flame.
Resistance of removable cutting edges against thermal and
mechanical shock is an important indicator of quality as well as its
abrasion resistance. Breach of the edge or its crumble may occur due
to cyclic loading. We can observe it not only during the interrupted
cutting (milling, turning areas abandoned hole or slot), but also in
continuous cutting. This is due to the volatility of cutting force on
cutting. Frequency of the volatility in this case depends on the type
of rising chips (chip size element). For difficult-to-machine materials
such as austenitic steel particularly happened at higher cutting speeds
for the localization of plastic deformation in the shear plane and for
the inception of separate elements substantially continuous chips.
This leads to variations of cutting forces substantially greater than for
other types of steel.
Abstract: The fractal-shaped orifices are assumed to have a
significant effect on the pressure drop downstream pipe flow due to
their edge self-similarity shape which enhances the mixing
properties. Here, we investigate the pressure drop after these fractals
using a digital micro-manometer at different stations downstream a
turbulent flow pipe then a direct comparison has been made with the
pressure drop measured from regular orifices with the same flow
area. Our results showed that the fractal-shaped orifices have a
significant effect on the pressure drop downstream the flow. Also
the pressure drop measured across the fractal-shaped orifices is
noticed to be lower that that from ordinary orifices of the same flow
areas. This result could be important in designing piping systems
from point of view of losses consideration with the same flow
control area. This is promising to use the fractal-shaped orifices as
flowmeters as they can sense the pressure drop across them
accurately with minimum losses than the regular ones.
Abstract: This paper explores the scalability issues associated
with solving the Named Entity Recognition (NER) problem using
Support Vector Machines (SVM) and high-dimensional features. The
performance results of a set of experiments conducted using binary
and multi-class SVM with increasing training data sizes are
examined. The NER domain chosen for these experiments is the
biomedical publications domain, especially selected due to its
importance and inherent challenges. A simple machine learning
approach is used that eliminates prior language knowledge such as
part-of-speech or noun phrase tagging thereby allowing for its
applicability across languages. No domain-specific knowledge is
included. The accuracy measures achieved are comparable to those
obtained using more complex approaches, which constitutes a
motivation to investigate ways to improve the scalability of multiclass
SVM in order to make the solution more practical and useable.
Improving training time of multi-class SVM would make support
vector machines a more viable and practical machine learning
solution for real-world problems with large datasets. An initial
prototype results in great improvement of the training time at the
expense of memory requirements.