Abstract: ECG analysis method was developed using ROC
analysis of PVC detecting algorithm. ECG signal of MIT-BIH
arrhythmia database was analyzed by MATLAB. First of all, the
baseline was removed by median filter to preprocess the ECG signal.
R peaks were detected for ECG analysis method, and normal VCG
was extracted for VCG analysis method. Four PVC detecting
algorithm was analyzed by ROC curve, which parameters are
maximum amplitude of QRS complex, width of QRS complex, r-r
interval and geometric mean of VCG. To set cut-off value of
parameters, ROC curve was estimated by true-positive rate
(sensitivity) and false-positive rate. sensitivity and false negative rate
(specificity) of ROC curve calculated, and ECG was analyzed using
cut-off value which was estimated from ROC curve. As a result, PVC
detecting algorithm of VCG geometric mean have high availability,
and PVC could be detected more accurately with amplitude and width
of QRS complex.
Abstract: This paper addresses one important aspect of
combustion system analysis, the spray evaporation and
dispersion modeling. In this study we assume an empty
cylinder which is as a simulator for a ramjet engine and the
cylinder has been studied by cold flow. Four nozzles have the
duties of injection which are located in the entrance of
cylinder. The air flow comes into the cylinder from one side
and injection operation will be done. By changing injection
velocity and entrance air flow velocity, we have studied
droplet sizing and efficient mass fraction of fuel vapor near
and at the exit area. We named the mass of fuel vapor inside
the flammability limit as the efficient mass fraction. Further,
we decreased the initial temperature of fuel droplets and we
have repeated the investigating again. To fulfill the calculation
we used a modified version of KIVA-3V.
Abstract: This paper presents the experimental results of
discharge current phenomena on various humidity, temperature,
pressure and pollutant conditions of epoxy resin specimen. The
leakage distance of specimen was 3 cm, that it was supplied by high
voltage. The polluted condition was given with NaCl artificial
pollutant. The conducted measurements were discharge current and
applied voltage. The specimen was put in a hermetically sealed
chamber, and the current waveforms were analyzed with FFT.
The result indicated that on discharge condition, the fifth
harmonics still had dominant, rather than third one. The third
harmonics tent to be appeared on low pressure heavily polluted
condition, and followed by high humidity heavily polluted condition.
On the heavily polluted specimen, the peaks discharge current points
would be high and more frequent. Nevertheless, the specimen still
had capacitive property. Besides that, usually discharge current
points were more frequent. The influence of low pressure was still
dominant to be easier to discharge. The non-linear property would be
appear explicitly on low pressure and heavily polluted condition.
Abstract: With the growth of electricity generation from gas
energy gas pipeline reliability can substantially impact the electric
generation. A physical disruption to pipeline or to a compressor
station can interrupt the flow of gas or reduce the pressure and lead
to loss of multiple gas-fired electric generators, which could
dramatically reduce the supplied power and threaten the power
system security. Gas pressure drops during peak loading time on
pipeline system, is a common problem in network with no enough
transportation capacity which limits gas transportation and causes
many problem for thermal domain power systems in supplying their
demand. For a feasible generation scheduling planning in networks
with no sufficient gas transportation capacity, it is required to
consider gas pipeline constraints in solving the optimization problem
and evaluate the impacts of gas consumption in power plants on gas
pipelines operating condition. This paper studies about operating of
gas fired power plants in critical conditions when the demand of gas
and electricity peak together. An integrated model of gas and electric
model is used to consider the gas pipeline constraints in the economic
dispatch problem of gas-fueled thermal generator units.
Abstract: A numerical study on the influence of electroosmotic flow on analyte preconcentration by isotachophoresis ( ITP) is made. We consider that the double layer induced electroosmotic flow ( EOF) counterbalance the electrophoretic velocity and a stationary ITP stacked zones results. We solve the Navier-Stokes equations coupled with the Nernst-Planck equations to determine the local convective velocity and the preconcentration dynamics of ions. Our numerical algorithm is based on a finite volume method along with a secondorder upwind scheme. The present numerical algorithm can capture the the sharp boundaries of step-changes ( plateau mode) or zones of steep gradients ( peak mode) accurately. The convection of ions due to EOF reduces the resolution of the ITP transition zones and produces a dispersion in analyte zones. The role of the electrokinetic parameters which induces dispersion is analyzed. A one-dimensional model for the area-averaged concentrations based on the Taylor-Aristype effective diffusivity is found to be in good agreement with the computed solutions.
Abstract: The aim of this study was to investigate the effect of blood viscosity on the radial pulse wave. For this, we obtained the radial pulse wave of 15 males with abnormal high hematocrit level and 47 males with normal hematocrit level at the age of thirties and forties. Various variables of the radial pulse wave between two groups were analyzed and compared by Student's T test. There are significant differences in several variables about height, time and area of the pulse wave. The first peak of the radial pulse wave was higher in abnormal high hematocrit group, but the third peak was higher and longer in normal hematocrit group. Our results suggest that the radial pulse wave can be used for diagnosis of high blood viscosity and more clinical application.
Abstract: This paper examines two policy spaces–the ARC and TVA–and their spatialized politics. The research observes that the regional concept informs public policy and can contribute to the formation of stable policy initiatives. Using the subsystem framework to understand the political viability of policy regimes, the authors conclude policy geographies that appeal to traditional definitions of regions are more stable over time. In contrast, geographies that fail to reflect pre-existing representations of space are engaged in more competitive subsystem politics. The paper demonstrates that the spatial practices of policy regions and their directional politics influence the political viability of programs. The paper concludes that policy spaces should institutionalize pre-existing geographies–not manufacture new ones.
Abstract: Mung bean starches were subjected to heat-moisture treatment (HMT) by different moisture contents (15%, 20%, 25%, 30% and 35%) at 120Ôäâ for 12h. The impact on the yields of resistant starch (RS), microstructure, physicochemical and functional properties was investigated. Compared to native starch, the RS content of heat-moisture treated starches increased significantly. The RS level of HMT-20 was the highest of all the starches. Birefringence was displayed clear at the center of native starch. For HMT starches, pronounced birefringence was exhibited on the periphery of starch granules; however, birefringence disappeared at the centre of some starch granules. The shape of HMT starches hadn-t been changed and the integrity of starch granules was preserved for all the conditions. Concavity could be observed on HMT starches under scanning electronic microscopy. After HMT, apparent amylose contents were increased and starch macromolecule was degraded in comparison with those of native starch. There was a reduction in swelling power on HMT starches, but the solubility of HMT starches was higher than that of native starch. Both of native and HMT starches showed A-type X-ray diffraction pattern. Furthermore, there is a higher intensity at the peak of 15.0 and 22.9 Å than those of native starch.
Abstract: Palm shell obtained from coastal part of southern
India was studied for the removal for the adsorption of Hg (II) ions.
Batch adsorption experiments were carried out as a function of pH,
concentration of Hg (II) ions, time, temperature and adsorbent dose.
Maximum removal was seen in the range pH 4.0- pH 7.0. The palm
shell powder used as adsorbent was characterized for its surface area,
SEM, PXRD, FTIR, ion exchange capacity, moisture content, and
bulk density, soluble content in water and acid and pH. The
experimental results were analyzed using Langmuir I, II, III, IV and
Freundlich adsorption isotherms. The batch sorption kinetics was
studied for the first order reversible reaction, pseudo first order;
pseudo second order reaction and the intra-particle diffusion reaction.
The biomass was successfully used for removal Hg (II) from
synthetic and industrial effluents and the technique appears
industrially applicable and viable.
Abstract: The literature reports a large number of approaches for
measuring the similarity between protein sequences. Most of these
approaches estimate this similarity using alignment-based techniques
that do not necessarily yield biologically plausible results, for two
reasons.
First, for the case of non-alignable (i.e., not yet definitively aligned
and biologically approved) sequences such as multi-domain, circular
permutation and tandem repeat protein sequences, alignment-based
approaches do not succeed in producing biologically plausible results.
This is due to the nature of the alignment, which is based on the
matching of subsequences in equivalent positions, while non-alignable
proteins often have similar and conserved domains in non-equivalent
positions.
Second, the alignment-based approaches lead to similarity measures
that depend heavily on the parameters set by the user for the alignment
(e.g., gap penalties and substitution matrices). For easily alignable
protein sequences, it's possible to supply a suitable combination of
input parameters that allows such an approach to yield biologically
plausible results. However, for difficult-to-align protein sequences,
supplying different combinations of input parameters yields different
results. Such variable results create ambiguities and complicate the
similarity measurement task.
To overcome these drawbacks, this paper describes a novel and
effective approach for measuring the similarity between protein
sequences, called SAF for Substitution and Alignment Free. Without
resorting either to the alignment of protein sequences or to substitution
relations between amino acids, SAF is able to efficiently detect the
significant subsequences that best represent the intrinsic properties of
protein sequences, those underlying the chronological dependencies of
structural features and biochemical activities of protein sequences.
Moreover, by using a new efficient subsequence matching scheme,
SAF more efficiently handles protein sequences that contain similar
structural features with significant meaning in chronologically
non-equivalent positions. To show the effectiveness of SAF, extensive
experiments were performed on protein datasets from different
databases, and the results were compared with those obtained by
several mainstream algorithms.
Abstract: We study in this paper the effect of the scene
changing on image sequences coding system using Embedded
Zerotree Wavelet (EZW). The scene changing considered here is the
full motion which may occurs. A special image sequence is generated
where the scene changing occurs randomly. Two scenarios are
considered: In the first scenario, the system must provide the
reconstruction quality as best as possible by the management of the
bit rate (BR) while the scene changing occurs. In the second scenario,
the system must keep the bit rate as constant as possible by the
management of the reconstruction quality. The first scenario may be
motivated by the availability of a large band pass transmission
channel where an increase of the bit rate may be possible to keep the
reconstruction quality up to a given threshold. The second scenario
may be concerned by the narrow band pass transmission channel
where an increase of the bit rate is not possible. In this last case,
applications for which the reconstruction quality is not a constraint
may be considered. The simulations are performed with five scales
wavelet decomposition using the 9/7-tap filter bank biorthogonal
wavelet. The entropy coding is performed using a specific defined
binary code book and EZW algorithm. Experimental results are
presented and compared to LEAD H263 EVAL. It is shown that if
the reconstruction quality is the constraint, the system increases the
bit rate to obtain the required quality. In the case where the bit rate
must be constant, the system is unable to provide the required quality
if the scene change occurs; however, the system is able to improve
the quality while the scene changing disappears.
Abstract: This study is designed to investigate errors emerged in written texts produced by 30 Turkish EFL learners with an explanatory, and thus, qualitative perspective. Erroneous language elements were identified by the researcher first and then their grammaticality and intelligibility were checked by five native speakers of English. The analysis of the data showed that it is difficult to claim that an error stems from only one single factor since different features of an error are triggered by different factors. Our findings revealed two different types of errors: those which stem from the interference of L1 with L2 and those which are developmental ones. The former type contains more global errors whereas the errors in latter type are more intelligible.
Abstract: The ITE Project is a project that has 1800 km length
and across the Turkey's land through east to west. The project of
pipeline enters geographically from Iran to Doğubayazit (Turkey) in
the east, exits to Greece from Ipsala province of Turkey in the west.
This project is the one of the international projects in such scale that
provides the natural gas of Iran and Caspian Sea through the
European continent. In this investigation, some information will be
given about the methods used to verify the direction of the pipeline
and the technical properties of the results obtained. The cost of
project itself entirely depends on the direction of the pipeline which
would be as short as possible and the specifications of the land cover.
Production standards of 1/2000 scaled digital orthophoto and vectoral
maps as a results of the use of map production materials and methods
(such as high resolution satellite images, and digital aerial images
captured from digital aerial cameras), will also be given in this report.
According to Turkish national map production standards, TM
((Transversal Mercator, 3 degree) projection is used for large scale
map and UTM (Universal Transversal Mercator, 6 degree) is used for
small scale map production standards. Some information is also given
about the projection used in the ITE natural gas pipeline project.
Abstract: In this paper, a new time-delay estimation
technique based on the cross IB-energy operator [5] is
introduced. This quadratic energy detector measures how
much a signal is present in another one. The location of the
peak of the energy operator, corresponding to the maximum of
interaction between the two signals, is the estimate of the
delay. The method is a fully data-driven approach. The
discrete version of the continuous-time form of the cross IBenergy
operator, for its implementation, is presented. The
effectiveness of the proposed method is demonstrated on real
underwater acoustic signals arriving from targets and the
results compared to the cross-correlation method.
Abstract: 17α-ethynylestradiol (EE2) is a synthetic estrogen
used as a key ingredient in an oral contraceptives pill. EE2 is an
endocrine disrupting compound, high in estrogenic potency.
Although EE2 exhibits low degree of biodegradability with common
microorganisms in wastewater treatment plants (WWTPs), this
compound can be biotransformed by ammonia-oxidizing bacteria
(AOB) via a co-metabolism mechanism in WWTPs. This study
aimed to investigate the effect of real wastewater on
biotransformation of EE2 by AOB. A preliminary experiment on the
effect of nitrite and pH levels on abiotic transformation of EE2
suggested that the abiotic transformation occurred at only pH
Abstract: Finding effective ways of improving university quality assurance requires, as well, a retraining of the staff. This article illustrates an Online Programme of Excellence Model (OPEM), based on the European quality assurance model, for improving participants- formative programme standards. The results of applying this OPEM indicate the necessity of quality policies that support the evaluators- competencies to improve formative programmes. The study concludes by outlining how faculty and agency staff can use OPEM for the internal and external quality assurance of formative programmes.
Abstract: In this paper we present a method of abrupt cut detection with a novel logic of frames- comparison. Actual frame is compared with its motion estimated prediction instead of comparison with successive frame. Four different similarity metrics were employed to estimate the resemblance of compared frames. Obtained results were evaluated by standard used measures of test accuracy and compared with existing approach. Based on the results, we claim the proposed method is more effective and Pearson correlation coefficient obtained the best results among chosen similarity metrics.
Abstract: Information sharing and exchange, rather than
information processing, is what characterizes information
technology in the 21st century. Ontologies, as shared common
understanding, gain increasing attention, as they appear as the
most promising solution to enable information sharing both at
a semantic level and in a machine-processable way. Domain
Ontology-based modeling has been exploited to provide
shareability and information exchange among diversified,
heterogeneous applications of enterprises.
Contextual ontologies are “an explicit specification of
contextual conceptualization". That is: ontology is
characterized by concepts that have multiple representations
and they may exist in several contexts. Hence, contextual
ontologies are a set of concepts and relationships, which are
seen from different perspectives. Contextualization is to allow
for ontologies to be partitioned according to their contexts.
The need for contextual ontologies in enterprise modeling
has become crucial due to the nature of today's competitive
market. Information resources in enterprise is distributed and
diversified and is in need to be shared and communicated
locally through the intranet and globally though the internet.
This paper discusses the roles that ontologies play in an
enterprise modeling, and how ontologies assist in building a
conceptual model in order to provide communicative and
interoperable information systems. The issue of enterprise
modeling based on contextual domain ontology is also
investigated, and a framework is proposed for an enterprise
model that consists of various applications.
Abstract: This study examines the possibility to apply the theory of multidimensional accounting (momentum accounting) in a Brazilian Navy-s Services Provider Military Organization (Organização Militar Prestadora de Serviços - OMPS). In general, the core of the said theory is the fact that Accounting does not recognize the inertia of transactions occurring in an entity, and that occur repeatedly in some cases, regardless of the implementation of new actions by its managers. The study evaluates the possibility of greater use of information recorded in the financial statements of the unit of analysis, within the strategic decisions of the organization. As a research strategy, we adopted the case study. The results infer that it is possible to use the theory in the context of a multidimensional OMPS, promoting useful information for decision-making and thereby contributing to the strengthening of the necessary alignment of its administration with the current desires of the Brazilian society.
Abstract: This work is an attempt to use the standard Smoothed
Particle Hydrodynamics methodology for the simulation of the
complex unsteady, free-surface flow in a rotating Turgo impulse
water turbine. A comparison of two different geometries was
conducted. The SPH method due to its mesh-less nature is capable of
capturing the flow features appearing in the turbine, without
diffusion at the water/air interface. Furthermore results are compared
with a commercial CFD package (Fluent®) and the SPH algorithm
proves to be capable of providing similar results, in much less time
than the mesh based CFD program. A parametric study was also
performed regarding the turbine inlet angle.