Abstract: The number of persons with implanted cardiac
pacemakers (PM) has increased in Western countries. The aim of this
paper is to investigate the possible situations where persons with a
PM may be exposed to extremely low frequency (ELF) electric (EF)
and magnetic fields (MF) that may disturb their PM. Based on our
earlier studies, it is possible to find such high public exposure to EFs
only in some places near 400 kV power lines, where an EF may
disturb a PM in unipolar mode. Such EFs cannot be found near 110
kV power lines. Disturbing MFs can be found near welding
machines. However, we do not have measurement data from welding.
Based on literature and earlier studies at Tampere University of
Technology, it is difficult to find public EF or MF exposure that is
high enough to interfere with PMs.
Abstract: In 2010-2011, the research on zooplankton was
conducted in the southern part of the Baltic Sea to determine seasonal
variability in changes occurring throughout the zooplankton in 2010
and 2011, both in the region of Gdańsk Deep, and in the western part
of Gdańsk Bay. The research in the sea showed that the taxonomic
composition of holoplankton in the southern part of the Baltic Sea
was similar to that recorded in this region for many years. The
maximum values of abundance and biomass of zooplankton both in
the Deep and the Bay of Gdańsk were observed in the summer
season. Copepoda dominated in the composition of zooplankton for
almost the entire study period, while rotifers occurred in larger
numbers only in the summer 2010 in the Gdańsk Deep as well as in
May and July 2010 in the western part of Gdańsk Bay, and
meroplankton – in April 2011.
Abstract: Forward Osmosis (FO) polyamide thin-film composite
membranes have been prepared by interfacial polymerization using
commercial UF polyethersulfoneas membrane support. Different
interfacial polymerization times (10s, 30s and 60s) in the organic
solution containing trimesoyl chloride (TMC) at constant m-phenylenediamine
(MPD) concentration (2% w/v) were studied. The
synthesized polyamide membranes then tested for treatment of
natural organic matter (NOM) and compared to commercial Cellulose
TriAcetate (CTA) membrane. It was found that membrane prepared
with higher reaction time (30s and 60s) exhibited better membrane
performance (flux and humic acid removal) over commercial CTA
membrane.
Abstract: This paper presents experimental investigation and
finite element analysis on buckling behavior of irregular section coldformed
steel columns under axially concentric loading. For the
experimental study, four different sections of columns were tested to
investigate effect of stiffening and width-to-thickness ratio on
buckling behavior. For each of the section, three lengths of 230, 950
and 1900 mm. were studied representing short, intermediate long and
long columns, respectively. Then, nonlinear finite element analyses
of the tested columns were performed. The comparisons in terms of
load-deformation response and buckling mode show good agreement
and hence the FEM models were validated. Parametric study of
stiffening element and thickness of 1.0, 1.15, 1.2, 1.5, 1.6 and 2.0
mm. was analyzed. The test results showed that stiffening effect pays
a large contribution to prevent distortional mode. The increase in wall
thickness enhanced buckling stress beyond the yielding strength in
short and intermediate columns, but not for the long columns.
Abstract: Verification of vented wooden façade system with
bonded joints is presented in this paper. The potential of bonded
joints is studied and described in more detail. The paper presents the results of an experimental and theoretical research about the effects of freeze cycling on the bonded joint. For the purpose of tests spruce
timber profiles were chosen for the load bearing substructure. Planks from wooden plastic composite and Siberian larch are representing facade cladding. Two types of industrial polyurethane adhesives intended for structural bonding were selected. The article is focused on the preparation as well as on the subsequent curing and conditioning of test samples. All test samples were subjected to 15 cycles that represents sudden temperature changes, i.e. immersion in a water bath at (293.15 ± 3) K for 6 hours and subsequent freezing to (253.15 ± 2) K for 18 hours. Furthermore, the retention of bond strength between substructure and cladding wastested and strength in shear was determined under tensile stress.Research data indicate that little, if any, damage to the bond results from freezingcycles. Additionally, the suitability of selected group of adhesives in combination with timber substructure was confirmed.
Abstract: In this paper, a numerical simulation of a finned store
separating from a wing-pylon configuration has been studied and
validated. A dynamic unstructured tetrahedral mesh approach is
accomplished by using three grid sizes to numerically solving the
discretized three dimensional, inviscid and compressible Euler
equations. The method used for computations of separation of an
external store assuming quasi-steady flow condition. Computations of
quasi-steady flow have been directly coupled to a six degree-offreedom
(6DOF) rigid-body motion code to generate store
trajectories. The pressure coefficients at four different angular cuts
and time histories of various trajectory parameters and wing pressure
distribution during the store separation are compared for every grid
size with published experimental data.
Abstract: The mechanisms underlying the association between
obesity and asthma may be related to a decreased immunological
tolerance induced by a defective function of regulatory T cells
(Tregs). The aim of this study is to establish the potential link
between these diseases and CD4+, CD25+ FoxP3+ Tregs as well as T
helper cells (Ths) in children. This is a prospective case control
study. Obese (n:40), asthmatic (n:40), asthmatic obese (n:40) and
healthy children (n:40), who don't have any acute or chronic diseases,
were included in this study. Obese children were evaluated according
to WHO criteria. Asthmatic patients were chosen based on GINA
criteria. Parents were asked to fill up the questionnaire. Informed
consent forms were taken. Blood samples were marked with CD4+,
CD25+ and FoxP3+ in order to determine Tregs and Ths by flow
cytometric method. Statistical analyses were performed. p≤0.05 was
chosen as meaningful threshold. Tregs exhibiting anti-inflammatory
nature were significantly lower in obese (0,16%; p≤0,001), asthmatic
(0,25%; p≤0,01) and asthmatic obese (0,29%; p≤0,05) groups than
the control group (0,38%). Ths were counted higher in asthma group
than the control (p≤0,01) and obese (p≤0,001) groups. T cell
immunity plays important roles in obesity and asthma pathogeneses.
Decreased numbers of Tregs found in obese, asthmatic and asthmatic
obese children may help to elucidate some questions in
pathophysiology of these diseases. For HOMA-IR levels, any
significant difference was not noted between control and obese
groups, but statistically higher values were found for obese
asthmatics. The values obtained in all groups were found to be below
the critical cut off points. This finding has made the statistically
significant difference observed between Tregs of obese, asthmatic,
obese asthmatic and control groups much more valuable. These
findings will be useful in diagnosis and treatment of these disorders
and future studies are needed. The production and propagation of
Tregs may be promising in alternative asthma and obesity treatments.
Abstract: Experimental study of natural convection heat transfer
inside smooth and rough surfaces of vertical and inclined equilateral
triangular channels of different inclination angles with a uniformly
heated surface are performed. The inclination angle is changed from
15º to 90º. Smooth and rough surface of average roughness (0.02mm)
are used and their effect on the heat transfer characteristics are
studied. The local and average heat transfer coefficients and Nusselt
number are obtained for smooth and rough channels at different heat
flux values, different inclination angles and different Rayleigh
numbers (Ra) 6.48 × 105 ≤ Ra ≤ 4.78 × 106. The results show that
the local Nusselt number decreases with increase of axial distance
from the lower end of the triangular channel to a point near the upper
end of channel, and then, it slightly increases. Higher values of local
Nusselt number for rough channel along the axial distance compared
with the smooth channel. The average Nusselt number of rough
channel is higher than that of smooth channel by about 8.1% for
inclined case at θ = 45o and 10% for vertical case. The results
obtained are correlated using dimensionless groups for both rough
and smooth surfaces of the inclined and vertical triangular channels.
Abstract: Background - The TrendCare Patient Dependency
System is currently used by a large number of maternity Services
across Australia, New Zealand and Singapore. In 2012, 2013 and
2014 validation studies were initiated in all three countries to validate
the acuity tools used for women in labour, and postnatal mothers and
babies. This paper will present the findings of the validation study.
Aim - The aim of this study was to; identify if the care hours
provided by the TrendCare acuity system was an accurate reflection
of the care required by women and babies; obtain evidence of
changes required to acuity indicators and/or category timings to
ensure the TrendCare acuity system remains reliable and valid across
a range of maternity care models in three countries.
Method - A non-experimental action research methodology was
used across maternity services in four District Health Boards in New
Zealand, a large tertiary and a large secondary maternity service in
Singapore and a large public maternity service in Australia.
Standardised data collection forms and timing devices were used to
collect midwife contact times, with women and babies included in the
study. Rejection processes excluded samples when care was not
completed/rationed, and contact timing forms were incomplete. The
variances between actual timed midwife/mother/baby contact and the
TrendCare acuity category times were identified and investigated.
Results - Thirty two (88.9%) of the 36 TrendCare acuity category
timings, fell within the variance tolerance levels when compared to
the actual timings recorded for midwifery care. Four (11.1%)
TrendCare categories provided less minutes of care than the actual
timings and exceeded the variance tolerance level. These were all
night shift category timings. Nine postnatal categories were not able
to be compared as the sample size for these categories was
statistically insignificant. 100% of labour ward TrendCare categories
matched actual timings for midwifery care, all falling within the
variance tolerance levels.
The actual time provided by core midwifery staff to assist lead
maternity carer (LMC) midwives in New Zealand labour wards
showed a significant deviation to previous studies. The findings of
the study demonstrated the need for additional time allocations in
TrendCare to accommodate an increased level of assistance given to
LMC midwives.
Conclusion - The results demonstrated the importance of regularly
validating the TrendCare category timings with actual timings of the
care hours provided. It was evident from the findings that variances
to models of care and length of stay in maternity units have increased
midwifery workloads on the night shift. The level of assistance
provided by the core labour ward staff to the LMC midwife has
increased substantially.
Outcomes - As a consequence of this study, changes were made to
the night duty TrendCare maternity categories, additional acuity
indicators were developed and times for assisting LMC midwives in
labour ward increased. The updated TrendCare version was delivered
to maternity services in 2014.
Abstract: This article presents modeling studies of NiAl alloy
under solid-particle erosion and liquid-drop erosion. In the
solid-particle erosion simulation, attention is paid to the oxide scale
thickness variation on the alloy in high-temperature erosion
environments. The erosion damage is assumed to be deformation wear
and cutting wear mechanisms, incorporating the influence of the oxide
scale on the eroded surface; thus the instantaneous oxide thickness is
the result of synergetic effect of erosion and oxidation. For liquid-drop
erosion, special interest is in investigating the effects of drop velocity
and drop size on the damage of the target surface. The models of
impact stress wave, mean depth of penetration, and maximum depth of
erosion rate (Max DER) are employed to develop various maps for
NiAl alloy, including target thickness vs. drop size (diameter), rate of
mean depth of penetration (MDRP) vs. drop impact velocity, and
damage threshold velocity (DTV) vs. drop size.
Abstract: The biodegradable family of polymers
polyhydroxyalkanoates is an interesting substitute for convectional
fossil-based plastics. However, the manufacturing and environmental
impacts associated with their production via intracellular bacterial
fermentation are strongly dependent on the raw material used and on
energy consumption during the extraction process, limiting their
potential for commercialization. Industrial wastewater is studied in
this paper as a promising alternative feedstock for waste valorization.
Based on results from laboratory and pilot-scale experiments, a
conceptual process design, techno-economic analysis and life cycle
assessment are developed for the large-scale production of the most
common type of polyhydroxyalkanoate, polyhydroxbutyrate.
Intracellular polyhydroxybutyrate is obtained via fermentation of
microbial community present in industrial wastewater and the
downstream processing is based on chemical digestion with
surfactant and hypochlorite. The economic potential and
environmental performance results help identifying bottlenecks and
best opportunities to scale-up the process prior to industrial
implementation. The outcome of this research indicates that the
fermentation of wastewater towards PHB presents advantages
compared to traditional PHAs production from sugars because the
null environmental burdens and financial costs of the raw material in
the bioplastic production process. Nevertheless, process optimization
is still required to compete with the petrochemicals counterparts.
Abstract: The paper discusses mineral water consumer market
and development policy in Georgia, the tools and measures, which
will contribute to production of mineral waters and increase its
export.
The paper studies and analyses current situation in mineral water
production sector as well as the factors affecting increase and
reduction of its export. It’s noted that in order to gain and maintain
competitive advantage, it’s necessary to provide continuous supply of
high quality goods with modern design, open new distribution
channels to enter new markets, carry out broad promotional activities,
organize e-commerce. Economic policy plays an important role in
protecting markets from counterfeit goods. The state also plays an
important role in attracting foreign direct investments. Stable
business environment and export oriented strategy is the basis for the
country’s economic growth.
Based on the research, the paper suggests the strategy for
improving competitiveness of Georgian mineral waters; relevant
conclusions and recommendations are provided.
Abstract: Phelipanche ramosa is the most damaging obligate
flowering parasitic weed on wide species of cultivated plants. The
semi-arid regions of the world are considered the main centers of this
parasitic plant that causes heavy infestation. This is due to its
production of high numbers of seeds (up to 200,000) that remain
viable for extended periods (up to 20 years). In this study, 13
treatments for the control of Phelipanche were carried out, which
included agronomic, chemical, and biological treatments and the use
of resistant plant methods. In 2014, a trial was performed at the
Department of Agriculture, Food and Environment, University of
Foggia (southern Italy), on processing tomato (cv ‘Docet’) grown in
pots filled with soil taken from a field that was heavily infested by P.
ramosa). The tomato seedlings were transplanted on May 8, 2014,
into a sandy-clay soil (USDA). A randomized block design with 3
replicates (pots) was adopted. During the growing cycle of the
tomato, at 70, 75, 81 and 88 days after transplantation, the number of
P. ramosa shoots emerged in each pot was determined. The tomato
fruit were harvested on August 8, 2014, and the quantitative and
qualitative parameters were determined. All of the data were
subjected to analysis of variance (ANOVA) using the JMP software
(SAS Institute Inc. Cary, NC, USA), and for comparisons of means
(Tukey's tests). The data show that each treatment studied did not
provide complete control against P. ramosa. However, the virulence
of the attacks was mitigated by some of the treatments tried: radicon
biostimulant, compost activated with Fusarium, mineral fertilizer
nitrogen, sulfur, enzone, and the resistant tomato genotype. It is
assumed that these effects can be improved by combining some of
these treatments with each other, especially for a gradual and
continuing reduction of the “seed bank” of the parasite in the soil.
Abstract: In this paper, we introduced a gradient-based inverse
solver to obtain the missing boundary conditions based on the
readings of internal thermocouples. The results show that the method
is very sensitive to measurement errors, and becomes unstable when
small time steps are used. The artificial neural networks are shown to
be capable of capturing the whole thermal history on the run-out
table, but are not very effective in restoring the detailed behavior of
the boundary conditions. Also, they behave poorly in nonlinear cases
and where the boundary condition profile is different.
GA and PSO are more effective in finding a detailed
representation of the time-varying boundary conditions, as well as in
nonlinear cases. However, their convergence takes longer. A
variation of the basic PSO, called CRPSO, showed the best
performance among the three versions. Also, PSO proved to be
effective in handling noisy data, especially when its performance
parameters were tuned. An increase in the self-confidence parameter
was also found to be effective, as it increased the global search
capabilities of the algorithm. RPSO was the most effective variation
in dealing with noise, closely followed by CRPSO. The latter
variation is recommended for inverse heat conduction problems, as it
combines the efficiency and effectiveness required by these
problems.
Abstract: Co-crystal is believed to improve the solubility and
dissolution rates and thus, enhanced the bioavailability of poor water
soluble drugs particularly during the oral route of administration.
With the existing of poorly soluble drugs in pharmaceutical industry,
the screening of co-crystal formation using carbamazepine (CBZ) as
a model drug compound with dicarboxylic acids co-crystal formers
(CCF) namely fumaric (FA) and succinic (SA) acids in ethanol has
been studied. The co-crystal formations were studied by varying the
mol ratio values of CCF to CBZ to access the effect of CCF
concentration on the formation of the co-crystal. Solvent evaporation,
slurry and cooling crystallization which representing the solution
based method co-crystal screening were used. Based on the
differential scanning calorimetry (DSC) analysis, the melting point of
CBZ-SA in different ratio was in the range between 188oC-189oC.
For CBZ-FA form A and CBZ-FA form B the melting point in
different ratio were in the range of 174oC-175oC and 185oC-186oC
respectively. The product crystal from the screening was also
characterized using X-ray powder diffraction (XRPD). The XRPD
pattern profile analysis has shown that the CBZ co-crystals with FA
and SA were successfully formed for all ratios studied. The findings
revealed that CBZ-FA co-crystal were formed in two different
polymorphs. It was found that CBZ-FA form A and form B were
formed from evaporation and slurry crystallization methods
respectively. On the other hand, in cooling crystallization method,
CBZ-FA form A was formed at lower mol ratio of CCF to CBZ and
vice versa. This study disclosed that different methods and mol ratios
during the co-crystal screening can affect the outcome of co-crystal
produced such as polymorphic forms of co-crystal and thereof. Thus,
it was suggested that careful attentions is needed during the screening
since the co-crystal formation is currently one of the promising
approach to be considered in research and development for
pharmaceutical industry to improve the poorly soluble drugs.
Abstract: The convective heat and mass transfer in nanofluid
flow through a porous media due to a permeable stretching sheet with
magnetic field, viscous dissipation, chemical reaction and Soret
effects are numerically investigated. Two types of nanofluids, namely
Cu-water and Ag-water were studied. The governing boundary layer
equations are formulated and reduced to a set of ordinary differential
equations using similarity transformations and then solved
numerically using the Keller box method. Numerical results are
obtained for the skin friction coefficient, Nusselt number and
Sherwood number as well as for the velocity, temperature and
concentration profiles for selected values of the governing
parameters. Excellent validation of the present numerical results has
been achieved with the earlier linearly stretching sheet problems in
the literature.
Abstract: Gypsum (CaSO4.2H2O) is a mineral that is found in
large quantities in the Turkey and in the World. In this study, the
dissolution of this mineral in the diammonium hydrogen phosphate
solutions has been studied. The dissolution and dissolution kinetics of
gypsum in diammonium hydrogen phosphate solutions will be useful
for evaluating of solid wastes containing gypsum. Parameters such as
diammonium hydrogen phosphate concentration, temperature and
stirring speed affecting on the dissolution rate of the gypsum in
diammonium hydrogen phosphate solutions were investigated. In
experimental studies have researched effectiveness of the selected
parameters. The dissolution of gypsum were examined in two parts at
low and high temperatures. The experimental results were
successfully correlated by linear regression using Statistica program.
Dissolution curves were evaluated shrinking core models for solidfluid
systems. The activation energy was found to be 34.58 kJ/mol
and 44.45 kJ/mol for the low and the high temperatures. The
dissolution of gypsum was controlled by chemical reaction both low
temperatures and high temperatures.
Abstract: The arm length, hand length, hand breadth and middle
finger length of 1540 right-handed industrial workers of Haryana
state was used to assess the relationship between the upper limb
dimensions and stature. Initially, the data were analyzed using basic
univariate analysis and independent t-tests; then simple and multiple
linear regression models were used to estimate stature using SPSS
(version 17). There was a positive correlation between upper limb
measurements (hand length, hand breadth, arm length and middle
finger length) and stature (p < 0.01), which was highest for hand
length. The accuracy of stature prediction ranged from ± 54.897 mm
to ± 58.307 mm. The use of multiple regression equations gave better
results than simple regression equations. This study provides new
forensic standards for stature estimation from the upper limb
measurements of male industrial workers of Haryana (India). The
results of this research indicate that stature can be determined using
hand dimensions with accuracy, when only upper limb is available
due to any reasons likewise explosions, train/plane crashes, mutilated
bodies, etc. The regression formula derived in this study will be
useful for anatomists, archaeologists, anthropologists, design
engineers and forensic scientists for fairly prediction of stature using
regression equations.
Abstract: R.C.C. buildings with dual structural system
consisting of shear walls (or braces) and moment resisting frames
have been widely used to resist lateral forces during earthquakes. The
dual systems are designed to resist the total design lateral force in
proportion to their lateral stiffness. The response of combination of
braces and shear walls has not yet been studied. The combination
may prove to be more effective to resist lateral forces during
earthquakes. This concept has been applied to regular R.C.C.
buildings provided with shear walls, braces and their combinations.
Abstract: In this paper, the exergy analysis of vapor absorption
refrigeration system using LiBr-H2O as working fluid is carried out
with the modified Gouy-Stodola approach rather than the classical
Gouy-Stodola equation and effect of varying input parameters is also
studied on the performance of the system. As the modified approach
uses the concept of effective temperature, the mathematical
expressions for effective temperature have been formulated and
calculated for each component of the system. Various constraints and
equations are used to develop program in EES to solve these
equations. The main aim of this analysis is to determine the
performance of the system and the components having major
irreversible loss. Results show that exergy destruction rate is
considerable in absorber and generator followed by evaporator and
condenser. There is an increase in exergy destruction in generator,
absorber and condenser and decrease in the evaporator by the
modified approach as compared to the conventional approach. The
value of exergy determined by the modified Gouy-Stodola equation
deviates maximum i.e. 26% in the generator as compared to the
exergy calculated by the classical Gouy-Stodola method.