Abstract: With rapid technology scaling, the proportion of the
static power consumption catches up with dynamic power
consumption gradually. To decrease leakage consumption is
becoming more and more important in low-power design. This paper
presents a power-gating scheme for P-DTGAL (p-type dual
transmission gate adiabatic logic) circuits to reduce leakage power
dissipations under deep submicron process. The energy dissipations of
P-DTGAL circuits with power-gating scheme are investigated in
different processes, frequencies and active ratios. BSIM4 model is
adopted to reflect the characteristics of the leakage currents. HSPICE
simulations show that the leakage loss is greatly reduced by using the
P-DTGAL with power-gating techniques.
Abstract: Both the minimum energy consumption and
smoothness, which is quantified as a function of jerk, are generally
needed in many dynamic systems such as the automobile and the
pick-and-place robot manipulator that handles fragile equipments.
Nevertheless, many researchers come up with either solely
concerning on the minimum energy consumption or minimum jerk
trajectory. This research paper proposes a simple yet very interesting
when combining the minimum energy and jerk of indirect jerks
approaches in designing the time-dependent system yielding an
alternative optimal solution. Extremal solutions for the cost functions
of the minimum energy, the minimum jerk and combining them
together are found using the dynamic optimization methods together
with the numerical approximation. This is to allow us to simulate
and compare visually and statistically the time history of state inputs
employed by combining minimum energy and jerk designs. The
numerical solution of minimum direct jerk and energy problem are
exactly the same solution; however, the solutions from problem of
minimum energy yield the similar solution especially in term of
tendency.
Abstract: The purpose of this study is to analyze Green IT industry in major developed countries and to suggest overall directions for IT-Energy convergence industry. Recently, IT industry is pointed out as a problem such as environmental pollution, energy exhaustion, and high energy consumption. Therefore, Green IT gets focused which concerns as solution of these problems. However, since it is a beginning stage of this convergence area, there are only a few studies of IT-Energy convergence industry. According to this, this study examined the major developed countries in terms of institution arrangements, resources, markets and companies based on Van de Ven(1999)'s social system framework that shows relationship among key components of industrial infrastructure. Subsequently, the direction of the future study of convergence on IT and Energy industry is proposed.
Abstract: The purpose of this study is to find natural gait of
biped robot such as human being by analyzing the COG (Center Of
Gravity) trajectory of human being's gait. It is discovered that human
beings gait naturally maintain the stability and use the minimum
energy. This paper intends to find the natural gait pattern of biped
robot using the minimum energy as well as maintaining the stability by
analyzing the human's gait pattern that is measured from gait image on
the sagittal plane and COG trajectory on the frontal plane. It is not
possible to apply the torques of human's articulation to those of biped
robot's because they have different degrees of freedom. Nonetheless,
human and 5-link biped robots are similar in kinematics. For this, we
generate gait pattern of the 5-link biped robot by using the GA
algorithm of adaptation gait pattern which utilize the human's ZMP
(Zero Moment Point) and torque of all articulation that are measured
from human's gait pattern. The algorithm proposed creates biped
robot's fluent gait pattern as that of human being's and to minimize
energy consumption because the gait pattern of the 5-link biped robot
model is modeled after consideration about the torque of human's each
articulation on the sagittal plane and ZMP trajectory on the frontal
plane. This paper demonstrate that the algorithm proposed is superior
by evaluating 2 kinds of the 5-link biped robot applied to each gait
patterns generated both in the general way using inverse kinematics
and in the special way in which by considering visuality and
efficiency.
Abstract: One way for optimum loading of overdimensioning
conveyers is speed (capacity) decrement, with attention for
production capabilities and demands. At conveyers which drives with
three phase slip-ring induction motor, technically reasonable solution
for conveyer (driving motors) speed regulation is using constant
torque subsynchronous cascade with static semiconductor converter
and transformer for energy reversion to the power network. In the
paper is described mathematical model for parameter calculation of
two-motors 6 kV subsynchronous cascade. It is also demonstrated
that applying of this cascade gave several good properties, foremost
in electrical energy saving, also in improving of other energy
indexes, and finally that results in cost reduction of complete
electrical motor drive.
Abstract: In this paper, a reliable cooperative multipath routing
algorithm is proposed for data forwarding in wireless sensor networks
(WSNs). In this algorithm, data packets are forwarded towards the
base station (BS) through a number of paths, using a set of relay
nodes. In addition, the Rayleigh fading model is used to calculate
the evaluation metric of links. Here, the quality of reliability is
guaranteed by selecting optimal relay set with which the probability
of correct packet reception at the BS will exceed a predefined
threshold. Therefore, the proposed scheme ensures reliable packet
transmission to the BS. Furthermore, in the proposed algorithm,
energy efficiency is achieved by energy balancing (i.e. minimizing
the energy consumption of the bottleneck node of the routing path)
at the same time. This work also demonstrates that the proposed
algorithm outperforms existing algorithms in extending longevity of
the network, with respect to the quality of reliability. Given this, the
obtained results make possible reliable path selection with minimum
energy consumption in real time.
Abstract: This study investigates the electrical performance of a
planar solid oxide fuel cell unit with cross-flow configuration when the fuel utilization gets higher and the fuel inlet flow are non-uniform.
A software package in this study solves two-dimensional,
simultaneous, partial differential equations of mass, energy, and
electro-chemistry, without considering stack direction variation. The
results show that the fuel utilization increases with a decrease in the molar flow rate, and the average current density decreases when the
molar flow rate drops. In addition, non-uniform Pattern A will induce more severe happening of non-reaction area in the corner of the fuel
exit and the air inlet. This non-reaction area deteriorates the average
current density and then deteriorates the electrical performance to –7%.
Abstract: Lighting upgrades involve relatively lower costs which
allow the benefits to be spread more widely than is possible with any
other energy efficiency measure. In order to popularize the adoption of
CFL in Taiwan, the authority proposes to implement a new energy efficient lamp comparative label system. The current study was
accordingly undertaken to investigate the factors affecting the performance and the deviation of actual and labeled performance of
commercially available integrated CFLs. In this paper, standard test
methods to determine the electrical and photometric performances of
CFL were developed based on CIE 84-1989 and CIE 60901-1987,
then 55 selected CFLs from market were tested. The results show that
with higher color temperature of CFLs lower efficacy are achieved. It
was noticed that the most packaging of CFL often lack the information of Color Rendering Index. Also, there was no correlation between
price and performance of the CFLs was indicated in this work. The results of this paper might help consumers to make more informed
CFL-purchasing decisions.
Abstract: Querying a data source and routing data towards sink
becomes a serious challenge in static wireless sensor networks if sink
and/or data source are mobile. Many a times the event to be observed
either moves or spreads across wide area making maintenance of
continuous path between source and sink a challenge. Also, sink can
move while query is being issued or data is on its way towards sink.
In this paper, we extend our already proposed Grid Based Data
Dissemination (GBDD) scheme which is a virtual grid based
topology management scheme restricting impact of movement of
sink(s) and event(s) to some specific cells of a grid. This obviates the
need for frequent path modifications and hence maintains continuous
flow of data while minimizing the network energy consumptions.
Simulation experiments show significant improvements in network
energy savings and average packet delay for a packet to reach at sink.
Abstract: The demand of the energy management systems (EMS) set forth by modern power systems requires fast energy management systems. Contingency analysis is among the functions in EMS which is time consuming. In order to handle this limitation, this paper introduces agent based technology in the contingency analysis. The main function of agents is to speed up the performance. Negotiations process in decision making is explained and the issue set forth is the minimization of the operating costs. The IEEE 14 bus system and its line outage have been used in the research and simulation results are presented.
Abstract: In this paper, we present the design and experimental
evaluation of complementary energy path adiabatic logic (CEPAL)
based 1 bit full adder circuit. A simulative investigation on the
proposed full adder has been done using VIRTUOSO SPECTRE
simulator of cadence in 0.18μm UMC technology and its
performance has been compared with the conventional CMOS full
adder circuit. The CEPAL based full adder circuit exhibits the energy
saving of 70% to the conventional CMOS full adder circuit, at 100
MHz frequency and 1.8V operating voltage.
Abstract: The Pulsed Compression Reactor promises to be a
compact, economical and energy efficient alternative to conventional
chemical reactors.
In this article, the production of synthesis gas using the Pulsed
Compression Reactor is investigated. This is done experimentally as
well as with simulations. The experiments are done by means of a
single shot reactor, which replicates a representative, single
reciprocation of the Pulsed Compression Reactor with great control
over the reactant composition, reactor temperature and pressure and
temperature history. Simulations are done with a relatively simple
method, which uses different models for the chemistry and
thermodynamic properties of the species in the reactor. Simulation
results show very good agreement with the experimental data, and
give great insight into the reaction processes that occur within the
cycle.
Abstract: Consumer electronics are pervasive. It is impossible to
imagine a household or office without DVD players, digital cameras,
printers, mobile phones, shavers, electrical toothbrushes, etc. All
these devices operate at different voltage levels ranging from 1.8 to
20 VDC, in the absence of universal standards. The voltages
available are however usually 120/230 VAC at 50/60 Hz. This
situation makes an individual electrical energy conversion system
necessary for each device. Such converters usually involve several
conversion stages and often operate with excessive losses and poor
reliability. The aim of the project presented in this paper is to design
and implement a multi-channel DC/DC converter system,
customizing the output voltage and current ratings according to the
requirements of the load. Distributed, multi-agent techniques will be
applied for the control of the DC/DC converters.
Abstract: In wireless sensor networks,the mobile agent technology is used in data fusion. According to the node residual energy and the results of partial integration,we design the node clustering algorithm. Optimization of mobile agent in the routing within the cluster strategy for wireless sensor networks to further reduce the amount of data transfer. Through the experiments, using mobile agents in the integration process within the cluster can be reduced the path loss in some extent.
Abstract: This paper investigates the application of large scale (LS-PV) two-axis tracking photovoltaic power plant in Al-Jagbob, Libya. A 50MW PV-grid connected (two-axis tracking) power plant design in Al-Jagbob, Libya has been carried out presently. A hetero-junction with intrinsic thin layer (HIT) type PV module has been selected and modeled. A Microsoft Excel-VBA program has been constructed to compute slope radiation, dew-point, sky temperature, and then cell temperature, maximum power output and module efficiency for this system, for tracking system. The results for energy production show that the total energy output is 128.5 GWh/year. The average module efficiency is 16.6%. The electricity generation capacity factor (CF) and solar capacity factor (SCF) were found to be 29.3% and 70.4% respectively. A 50MW two axis tracking power plant with a total energy output of 128.5 GWh/year would reduce CO2 pollution by 85,581 tonnes of each year. The payback time for the proposed LS-PV photovoltaic power plant was found to be 4 years.
Abstract: In a world of climate change and limited fossil fuel resources, renewable energy sources are playing an increasingly important role. Due to industrializations and population growth our economy and technologies today largely depend upon natural resources, which are not replaceable. Approximately 90% of our energy consumption comes from fossil fuels (viz. coal, oil and natural gas). The irony is that these resources are depleting. Also, the huge consumption of fossil fuels has caused visible damage to the environment in various forms viz. global warming, acid rains etc.
Abstract: Analysis of the elastic scattering of protons on 6,7Li
nuclei has been done in the framework of the optical model at the
beam energies up to 50 MeV. Differential cross sections for the 6,7Li +
p scattering were measured over the proton laboratory–energy range
from 400 to 1050 keV. The elastic scattering of 6,7Li+p data at
different proton incident energies have been analyzed using singlefolding
model. In each case the real potential obtained from the
folding model was supplemented by a phenomenological imaginary
potential, and during the fitting process the real potential was
normalized and the imaginary potential optimized. Normalization
factor NR is calculated in the range between 0.70 and 0.84.
Abstract: This paper concerns about the experimental and
numerical investigations of energy absorption and axial tearing
behaviour of aluminium 6060 circular thin walled tubes under static
axial compression. The tubes are received in T66 heat treatment
condition with fixed outer diameter of 42mm, thickness of 1.5mm
and length of 120mm. The primary variables are the conical die
angles (15°, 20° and 25°). Numerical simulations are carried on
ANSYS/LS-DYNA software tool, for investigating the effect of
friction between the tube and the die.
Abstract: This article attempts to analyze functionally graded beam thermal buckling along with piezoelectric layers applying based on the third order shearing deformation theory considering various boundary conditions. The beam properties are assumed to vary continuously from the lower surface to the upper surface of the beam. The equilibrium equations are derived using the total potential energy equations, Euler equations, piezoelectric material constitutive equations and third order shear deformation theory assumptions. In order to fulfill such an aim, at first functionally graded beam with piezoelectric layers applying the third order shearing deformation theory along with clamped -clamped boundary conditions are thoroughly analyzed, and then following making sure of the correctness of all the equations, the very same beam is analyzed with piezoelectric layers through simply-simply and simply-clamped boundary conditions. In this article buckling critical temperature for functionally graded beam is derived in two different ways, without piezoelectric layer and with piezoelectric layer and the results are compared together. Finally, all the conclusions obtained will be compared and contrasted with the same samples in the same and distinguished conditions through tables and charts. It would be noteworthy that in this article, the software MAPLE has been applied in order to do the numeral calculations.
Abstract: Perth will run out of available sustainable natural
water resources by 2015 if nothing is done to slow usage rates,
according to a Western Australian study [1]. Alternative water
technology options need to be considered for the long-term
guaranteed supply of water for agricultural, commercial, domestic
and industrial purposes. Seawater is an alternative source of water for
human consumption, because seawater can be desalinated and
supplied in large quantities to a very high quality.
While seawater desalination is a promising option, the technology
requires a large amount of energy which is typically generated from
fossil fuels. The combustion of fossil fuels emits greenhouse gases
(GHG) and, is implicated in climate change. In addition to
environmental emissions from electricity generation for desalination,
greenhouse gases are emitted in the production of chemicals and
membranes for water treatment. Since Australia is a signatory to the
Kyoto Protocol, it is important to quantify greenhouse gas emissions
from desalinated water production.
A life cycle assessment (LCA) has been carried out to determine
the greenhouse gas emissions from the production of 1 gigalitre (GL)
of water from the new plant. In this LCA analysis, a new desalination
plant that will be installed in Bunbury, Western Australia, and known
as Southern Seawater Desalinization Plant (SSDP), was taken as a
case study. The system boundary of the LCA mainly consists of three
stages: seawater extraction, treatment and delivery. The analysis
found that the equivalent of 3,890 tonnes of CO2 could be emitted
from the production of 1 GL of desalinated water. This LCA analysis
has also identified that the reverse osmosis process would cause the
most significant greenhouse emissions as a result of the electricity
used if this is generated from fossil fuels