Abstract: Contamination of aromatic compounds in water can
cause severe long-lasting effects not only for biotic organism but also
on human health. Several alternative technologies for remediation of
polluted water have been attempted. One of these is adsorption
process of aromatic compounds by using organic modified clay
mineral. Porous structure of clay is potential properties for molecular
adsorptivity and it can be increased by immobilizing hydrophobic
structure to attract organic compounds. In this work natural
montmorillonite were modified with cetyltrimethylammonium
(CTMA+) and was evaluated for use as adsorbents of aromatic
compounds: benzene, toluene, and 2-chloro phenol in its single and
multicomponent solution by ethanol:water solvent. Preparation of
CTMA-montmorillonite was conducted by simple ion exchange
procedure and characterization was conducted by using x-day
diffraction (XRD), Fourier-transform infra red (FTIR) and gas
sorption analysis. The influence of structural modification of
montmorillonite on its adsorption capacity and adsorption affinity of
organic compound were studied. It was shown that adsorptivity of
montmorillonite was increased by modification associated with
arrangements of CTMA+ in the structure even the specific surface
area of modified montmorillonite was lower than raw
montmorillonite. Adsorption rate indicated that material has affinity
to adsorb compound by following order: benzene> toluene > 2-chloro
phenol. The adsorption isotherms of benzene and toluene showed 1st
order adsorption kinetic indicating a partition phenomenon of
compounds between the aqueous and organophilic CTMAmontmorillonite.
Abstract: The pavement constructions on soft and expansive soils are not durable and unable to sustain heavy traffic loading. As a result, pavement failures and settlement problems will occur very often even under light traffic loading due to cyclic and rolling effects. Geotechnical engineers have dwelled deeply into this matter, and adopt various methods to improve the engineering characteristics of soft fine-grained soils and expansive soils. The problematic soils are either replaced by good and better quality material or treated by using chemical stabilization with various binding materials. Increased the strength and durability are also the part of the sustainability drive to reduce the environment footprint of the built environment by the efficient use of resources and waste recycle materials. This paper presents a series of laboratory tests and evaluates the effect of cement and fly ash on the strength and drainage characteristics of soil in Miri. The tests were performed at different percentages of cement and fly ash by dry weight of soil. Additional tests were also performed on soils treated with the combinations of fly ash with cement and lime. The results of this study indicate an increase in unconfined compression strength and a decrease in hydraulic conductivity of the treated soil.
Abstract: This research explorers the relationship between leadership style and continuous improvement (CI) teams. CI teams have several features that are not always found in other types of teams, including multi-functional members, short time period for performance, positive and actionable results, and exposure to senior leadership. There is no one best style of leadership for these teams. Instead, it is important to select the best leadership style for the situation. The leader must have the flexibility to change styles and the skill to use the chosen style effectively in order to ensure the team’s success.
Abstract: Information and Communication Technologies (ICT) are increasing in importance everyday, especially since the 90’s (last decade of birth for the Millennials generation). While social interactions involving the Millennials generation have been studied, a lack of investigation remains regarding the use of the ICT by this generation as well as the impact on outcomes in education and professional training. Observing and interviewing students preparing a MSc, we aimed at characterizing the interaction students-ICT during the courses. We found that up to 50% of the students (mainly female) could use ICT during courses at a rate of 0.84 occurrence/minutes for some of them, and they thought this involvement did not disturb learning, even was helpful. As recent researches show that multitasking leads people think they are much better than they actually are, further observations with assessments are needed to conclude whether or not the use ICT by students during the courses is a real strength.
Abstract: Monitoring of ecological systems is one of the major
issues in ecosystem research. The concepts and methodology of
mathematical systems theory provide useful tools to face this
problem. In many cases, state monitoring of a complex ecological
system consists in observation (measurement) of certain state
variables, and the whole state process has to be determined from the
observed data. The solution proposed in the paper is the design of an
observer system, which makes it possible to approximately recover
the state process from its partial observation. The method is
illustrated with a trophic chain of resource – producer – primary
consumer type and a numerical example is also presented.
Abstract: Cerium-doped lanthanum bromide LaBr3:Ce(5%)
crystals are considered to be one of the most advanced scintillator
materials used in PET scanning, combining a high light yield, fast
decay time and excellent energy resolution. Apart from the correct
choice of scintillator, it is also important to optimise the detector
geometry, not least in terms of source-to-detector distance in order to
obtain reliable measurements and efficiency. In this study a
commercially available 25 mm x 25 mm BrilLanCeTM 380 LaBr3: Ce
(5%) detector was characterised in terms of its efficiency at varying
source-to-detector distances. Gamma-ray spectra of 22Na, 60Co, and
137Cs were separately acquired at distances of 5, 10, 15, and 20cm. As
a result of the change in solid angle subtended by the detector, the
geometric efficiency reduced in efficiency with increasing distance.
High efficiencies at low distances can cause pulse pile-up when
subsequent photons are detected before previously detected events
have decayed. To reduce this systematic error the source-to-detector
distance should be balanced between efficiency and pulse pile-up
suppression as otherwise pile-up corrections would need to be
necessary at short distances. In addition to the experimental
measurements Monte Carlo simulations have been carried out for the
same setup, allowing a comparison of results. The advantages and
disadvantages of each approach have been highlighted.
Abstract: Quality of 2D and 3D cross-sectional images produce
by Computed Tomography primarily depend upon the degree of
precision of primary and secondary X-Ray intensity detection.
Traditional method of primary intensity detection is apt to errors.
Recently the X-Ray intensity measurement system along with smart
X-Ray sensors is developed by our group which is able to detect
primary X-Ray intensity unerringly. In this study a new smart X-Ray
sensor is developed using Light-to-Frequency converter TSL230
from Texas Instruments which has numerous advantages in terms of
noiseless data acquisition and transmission. TSL230 construction is
based on a silicon photodiode which converts incoming X-Ray
radiation into the proportional current signal. A current to frequency
converter is attached to this photodiode on a single monolithic CMOS
integrated circuit which provides proportional frequency count to
incoming current signal in the form of the pulse train. The frequency
count is delivered to the center of PICDEM FS USB board with
PIC18F4550 microcontroller mounted on it. With highly compact
electronic hardware, this Demo Board efficiently read the smart
sensor output data. The frequency output approaches overcome
nonlinear behavior of sensors with analog output thus un-attenuated
X-Ray intensities could be measured precisely and better
normalization could be acquired in order to attain high resolution.
Abstract: This paper presents a heuristic to solve large size 0-1 Multi constrained Knapsack problem (01MKP) which is NP-hard. Many researchers are used heuristic operator to identify the redundant constraints of Linear Programming Problem before applying the regular procedure to solve it. We use the intercept matrix to identify the zero valued variables of 01MKP which is known as redundant variables. In this heuristic, first the dominance property of the intercept matrix of constraints is exploited to reduce the search space to find the optimal or near optimal solutions of 01MKP, second, we improve the solution by using the pseudo-utility ratio based on surrogate constraint of 01MKP. This heuristic is tested for benchmark problems of sizes upto 2500, taken from literature and the results are compared with optimum solutions. Space and computational complexity of solving 01MKP using this approach are also presented. The encouraging results especially for relatively large size test problems indicate that this heuristic can successfully be used for finding good solutions for highly constrained NP-hard problems.
Abstract: Concrete performance is strongly affected by the
particle packing degree since it determines the distribution of the
cementitious component and the interaction of mineral particles. By
using packing theory designers will be able to select optimal
aggregate materials for preparing concrete with low cement content,
which is beneficial from the point of cost. Optimum particle packing
implies minimizing porosity and thereby reducing the amount of
cement paste needed to fill the voids between the aggregate particles,
taking also the rheology of the concrete into consideration. For
reaching good fluidity superplasticizers are required. The results from
pilot tests at Luleå University of Technology (LTU) show various
forms of the proposed theoretical models, and the empirical approach
taken in the study seems to provide a safer basis for developing new,
improved packing models.
Abstract: This paper deals with a new way for designing
external fixators applied in traumatology and orthopaedics. These
fixators can be applied in the treatment of open and unstable
fractures or for lengthening human or animal bones etc. The new
design is based on the development of Ilizarov and other techniques
(i.e. shape and weight optimalization based on composite materials,
application of smart materials, nanotechnology, low x-ray absorption,
antibacterial protection, patient's comfort, reduction in the duration
of the surgical treatment, and cost).
Abstract: Many well-known interconnection networks, such as kary n-cubes, recursive circulant graphs, generalized recursive circulant graphs, circulant graphs and so on, are shown to belong to the family of cycle composition networks. Recently, various studies about mutually independent hamiltonian cycles, abbreviated as MIHC-s, on interconnection networks are published. In this paper, using an improved construction method, we obtain MIHC-s on cycle composition networks with a much weaker condition than the known result. In fact, we established the existence of MIHC-s in the cycle composition networks and the result is optimal in the sense that the number of MIHC-s we constructed is maximal.
Abstract: The state-of-the-art Bag of Words model in Content-
Based Image Retrieval has been used for years but the relevance
feedback strategies for this model are not fully investigated. Inspired
from text retrieval, the Bag of Words model has the ability to use the
wealth of knowledge and practices available in text retrieval. We
study and experiment the relevance feedback model in text retrieval
for adapting it to image retrieval. The experiments show that the
techniques from text retrieval give good results for image retrieval
and that further improvements is possible.
Abstract: In a wireless communication system, a
predistorter(PD) is often employed to alleviate nonlinear distortions
due to operating a power amplifier near saturation, thereby improving
the system performance and reducing the interference to adjacent
channels. This paper presents a new adaptive polynomial digital
predistorter(DPD). The proposed DPD uses Coordinate Rotation
Digital Computing(CORDIC) processors and PD process by pipelined
architecture. It is simpler and faster than conventional adaptive
polynomial DPD. The performance of the proposed DPD is proved by
MATLAB simulation.
Abstract: Seismic design may require non-conventional
concept, due to the fact that the stiffness and layout of the structure
have a great effect on the overall structural behaviour, on the seismic
load intensity as well as on the internal force distribution. To find an
economical and optimal structural configuration the key issue is the
optimal design of the lateral load resisting system. This paper focuses
on the optimal design of regular, concentric braced frame (CBF)
multi-storey steel building structures. The optimal configurations are
determined by a numerical method using genetic algorithm approach,
developed by the authors. Aim is to find structural configurations
with minimum structural cost. The design constraints of objective
function are assigned in accordance with Eurocode 3 and Eurocode 8
guidelines. In this paper the results are presented for various building
geometries, different seismic intensities, and levels of energy
dissipation.
Abstract: Recently, lots of researchers are attracted to retrieving
multimedia database by using some impression words and their values.
Ikezoe-s research is one of the representatives and uses eight pairs of
opposite impression words. We had modified its retrieval interface and
proposed '2D-RIB'. In '2D-RIB', after a retrieval person selects a
single basic music, the system visually shows some other music
around the basic one along relative position. He/she can select one of
them fitting to his/her intention, as a retrieval result. The purpose of
this paper is to improve his/her satisfaction level to the retrieval result
in 2D-RIB. One of our extensions is to define and introduce the
following two measures: 'melody goodness' and 'general acceptance'.
We implement them in different five combinations. According to an
evaluation experiment, both of these two measures can contribute to
the improvement. Another extension is three types of customization.
We have implemented them and clarified which customization is
effective.
Abstract: The purpose of this study was to explore the complex
flow structure a novel active-type micromixer that based on concept of
Wankle-type rotor. The characteristics of this micromixer are two
folds; a rapid mixing of reagents in a limited space due to the
generation of multiple vortices and a graduate increment in dynamic
pressure as the mixed reagents is delivered to the output ports.
Present micro-mixer is consisted of a rotor with shape of triangle
column, a blending chamber and several inlet and outlet ports. The
geometry of blending chamber is designed to make the rotor can be
freely internal rotated with a constant eccentricity ratio. When the
shape of the blending chamber and the rotor are fixed, the effects of
rotating speed of rotor and the relative locations of ports on the mixing
efficiency are numerical studied. The governing equations are
unsteady, two-dimensional incompressible Navier-Stokes equation
and the working fluid is the water. The species concentration equation
is also solved to reveal the mass transfer process of reagents in various
regions then to evaluate the mixing efficiency.
The dynamic mesh technique was implemented to model the
dynamic volume shrinkage and expansion of three individual
sub-regions of blending chamber when the rotor conducted a complete
rotating cycle. Six types of ports configuration on the mixing
efficiency are considered in a range of Reynolds number from 10 to
300. The rapid mixing process was accomplished with the multiple
vortex structures within a tiny space due to the equilibrium of shear
force, viscous force and inertial force. Results showed that the highest
mixing efficiency could be attained in the following conditions: two
inlet and two outlet ports configuration, that is an included angle of 60
degrees between two inlets and an included angle of 120 degrees
between inlet and outlet ports when Re=10.
Abstract: The selection of parents and breeding strategies for
the successful maize hybrid production will be facilitated by
heterotic groupings of parental lines and determination of combining
abilities of them. Fourteen maize inbred lines, used in maize breeding
programs in Iran, were crossed in a diallel mating design. The 91 F1
hybrids and the 14 parental lines were studied during two years at
four locations of Iran for investigation of combining ability of
gentypes for grain yield and to determine heterotic patterns among
germplasm sources, using both, the Griffing-s method and the biplot
approach for diallel analysis. The graphical representation offered by
biplot analysis allowed a rapid and effective overview of general
combining ability (GCA) and specific combining ability (SCA)
effects of the inbred lines, their performance in crosses, as well as
grouping patterns of similar genotypes. GCA and SCA effects were
significant for grain yield (GY). Based on significant positive GCA
effects, the lines derived from LSC could be used as parent in crosses
to increase GY. The maximum best- parent heterosis values and
highest SCA effects resulted from crosses B73 × MO17 and A679 ×
MO17 for GY. The best heterotic patterns were LSC × RYD, which
would be potentially useful in maize breeding programs to obtain
high-yielding hybrids in the same climate of Iran.
Abstract: An efficient architecture for low jitter All Digital
Phase Locked Loop (ADPLL) suitable for high speed SoC
applications is presented in this paper. The ADPLL is designed using
standard cells and described by Hardware Description Language
(HDL). The ADPLL implemented in a 90 nm CMOS process can
operate from 10 to 200 MHz and achieve worst case frequency
acquisition in 14 reference clock cycles. The simulation result shows
that PLL has cycle to cycle jitter of 164 ps and period jitter of 100 ps
at 100MHz. Since the digitally controlled oscillator (DCO) can
achieve both high resolution and wide frequency range, it can meet
the demands of system-level integration. The proposed ADPLL can
easily be ported to different processes in a short time. Thus, it can
reduce the design time and design complexity of the ADPLL, making
it very suitable for System-on-Chip (SoC) applications.
Abstract: The aim of current study was to investigate the
changes in the quality parameters of Holstein bull semen during the
heat stress and the effect of feeding a source of omega-3 fatty acids
in this period. Samples were obtained from 19 Holstein bulls during
the expected time of heat stress in Iran (June to September 2009).
Control group (n=10) were fed a standard concentrate feed while
treatment group (n=9) had this feed top dressed with 100 g of an
omega-3 enriched nutriceutical. Semen quality was assessed on
ejaculates collected after 1, 5, 9 and 12 weeks of supplementation.
Computer-assisted assessment of sperm motility, viability (eosinnigrosin)
and hypo-osmotic swelling test (HOST) were conducted.
Heat stress affected sperm quality parameters by week 5 and 9
(p