Abstract: In this paper, we argue the security protocols of
ZigBee wireless sensor network in MAC layer. AES 128-bit
encryption algorithm in CCM* mode is secure transferred data;
however, AES-s secret key will be break within nearest future.
Efficient public key algorithm, ECC has been mixed with AES to
rescue the ZigBee wireless sensor from cipher text and replay attack.
Also, the proposed protocol can parallelize the integrity function to
increase system performance.
Abstract: Regenerative Thermal Oxidizer (RTO) is one of the
best solutions for removal of Volatile Organic Compounds (VOC)
from industrial processes. In the RTO, VOC in a raw gas are usually
decomposed at 950-1300 K and the combustion heat of VOC is
recovered by regenerative heat exchangers charged with ceramic
honeycombs. The optimization of the treatment of VOC leads to the
reduction of fuel addition to VOC decomposition, the minimization of
CO2 emission and operating cost as well.
In the present work, the thermal efficiency of the RTO was
investigated experimentally in a pilot-scale RTO unit using toluene as
a typical representative of VOC. As a result, it was recognized that the
radiative heat transfer was dominant in the preheating process of a raw
gas when the gas flow rate was relatively low. Further, it was found
that a minimum heat exchanger volume to achieve self combustion of
toluene without additional heating of the RTO by fuel combustion was
dependent on both the flow rate of a raw gas and the concentration of
toluene. The thermal efficiency calculated from fuel consumption and
the decomposed toluene ratio, was found to have a maximum value of
0.95 at a raw gas mass flow rate of 1810 kg·h-1 and honeycombs height
of 1.5m.
Abstract: In this paper we propose a new criterion for solving
the problem of channel shortening in multi-carrier systems. In a
discrete multitone receiver, a time-domain equalizer (TEQ) reduces
intersymbol interference (ISI) by shortening the effective duration of
the channel impulse response. Minimum mean square error (MMSE)
method for TEQ does not give satisfactory results. In [1] a new
criterion for partially equalizing severe ISI channels to reduce the
cyclic prefix overhead of the discrete multitone transceiver (DMT),
assuming a fixed transmission bandwidth, is introduced. Due to
specific constrained (unit morm constraint on the target impulse
response (TIR)) in their method, the freedom to choose optimum
vector (TIR) is reduced. Better results can be obtained by avoiding
the unit norm constraint on the target impulse response (TIR). In
this paper we change the cost function proposed in [1] to the cost
function of determining the maximum of a determinant subject to
linear matrix inequality (LMI) and quadratic constraint and solve the
resulting optimization problem. Usefulness of the proposed method
is shown with the help of simulations.
Abstract: This paper is a continuation of our interest in the influence of temperature on specific retention volumes and the resulting infinite dilution activity coefficients. This has a direct effect in the design of absorption and stripping columns for the abatement of volatile organic compounds. The interaction of 13 volatile organic compounds (VOCs) with polydimethylsiloxane (PDMS) at varying temperatures was studied by gas liquid chromatography (GLC). Infinite dilution activity coefficients and specific retention volumes obtained in this study were found to be in agreement with those obtained from static headspace and group contribution methods by the authors as well as literature values for similar systems. Temperature variation also allows for transport calculations for different seasons. The results of this work confirm that PDMS is well suited for the scrubbing of VOCs from waste gas streams. Plots of specific retention volumes against temperature gave linear van-t Hoff plots.
Abstract: Mobile devices, which are progressively surrounded
in our everyday life, have created a new paradigm where they
interconnect, interact and collaborate with each other. This network
can be used for flexible and secure coordinated sharing. On the other
hand Grid computing provides dependable, consistent, pervasive, and
inexpensive access to high-end computational capabilities. In this
paper, efforts are made to map the concepts of Grid on Ad-Hoc
networks because both exhibit similar kind of characteristics like
Scalability, Dynamism and Heterogeneity. In this context we
propose “Mobile Ad-Hoc Services Grid – MASGRID".
Abstract: Extracting and elaborating software requirements and
transforming them into viable software architecture are still an
intricate task. This paper defines a solution architecture which is
based on the blurred amalgamation of problem space and solution
space. The dependencies between domain constraints, requirements
and architecture and their importance are described that are to be
considered collectively while evolving from problem space to
solution space. This paper proposes a revised version of Twin Peaks
Model named Win Peaks Model that reconciles software
requirements and architecture in more consistent and adaptable
manner. Further the conflict between stakeholders- win-requirements
is resolved by proposed Voting methodology that is simple
adaptation of win-win requirements negotiation model and QARCC.
Abstract: Vehicle which are turning or maneuvering at high speeds
are susceptible to sliding and subsequently deviate from desired path. In
this paper the dynamics governing the Yaw/Roll behavior of a vehicle
has been simulated. Two different simulations have been used one for
the real vehicle, for which a fuzzy controller is designed to increase its
directional stability property. The other simulation is for a hypothetical
vehicle with much higher tire cornering stiffness which is capable of
developing the required lateral forces at the tire-ground patch contact to
attain the desired lateral acceleration for the vehicle to follow the
desired path without slippage. This simulation model is our reference
model.
The logic for keeping the vehicle on the desired track in the cornering
or maneuvering state is to have some braking forces on the inner or
outer tires based on the direction of vehicle deviation from the desired
path. The inputs to our vehicle simulation model is steer angle δ and
vehicle velocity V , and the outputs can be any kinematical parameters
like yaw rate, yaw acceleration, side slip angle, rate of side slip angle
and so on. The proposed fuzzy controller is a feed forward controller.
This controller has two inputs which are steer angle δ and vehicle
velocity V, and the output of the controller is the correcting moment M,
which guides the vehicle back to the desired track. To develop the
membership functions for the controller inputs and output and the fuzzy
rules, the vehicle simulation has been run for 1000 times and the
correcting moment have been determined by trial and error. Results of
the vehicle simulation with fuzzy controller are very promising
and show the vehicle performance is enhanced greatly over the
vehicle without the controller. In fact the vehicle performance
with the controller is very near the performance of the reference
ideal model.
Abstract: In areas of low to moderate seismicity many building contents and equipment are not positively fixed to the floor or tied to adjacent walls. Under seismic induced horizontal vibration, such contents and equipment can suffer from damage by either overturning or impact associated with rocking. This paper focuses on the estimation of shock on typical contents and equipment due to rocking. A simplified analytical model is outlined that can be used to estimate the maximum acceleration on a rocking object given its basic geometric and mechanical properties. The developed model was validated against experimental results. The experimental results revealed that the maximum shock acceleration can be underestimated if the static stiffness of the materials at the interface between the rocking object and floor is used rather than the dynamic stiffness. Excellent agreement between the model and experimental results was found when the dynamic stiffness for the interface material was used, which was found to be generally much higher than corresponding static stiffness under different investigated boundary conditions of the cushion. The proposed model can be a beneficial tool in performing a rapid assessment of shock sensitive components considered for possible seismic rectification.
Abstract: In order to upgrade the seismic resistibility of structures and enhance the functionality of an isolator, a new base isolator called the multiple trench friction pendulum system (MTFPS) is proposed in this study. The proposed MTFPS isolator is composed of a trench concave surface and several intermediate sliding plates in two orthogonal directions. Mathematical formulations have been derived to examine the characteristics of the proposed MTFPS isolator possessing multiple intermediate sliding plates. By means of mathematical formulations, it can be inferred that the natural period and damping effect of the MTFPS isolator with several intermediate sliding plates can be altered continually and controllably during earthquakes. Furthermore, results obtained from shaking table tests demonstrate that the proposed isolator provides good protection to structures for prevention of damage from strong earthquakes.
Abstract: The paper provides a literature review of the STEPNC
compliant research around the world. The first part of this paper
focuses on projects based on STEP compliance followed by research
and development in this area based on machining operations. Review
the literature relating to relevant STEP standards and application in
the area of turning centers. This research will review the various
research work, carried out from the evolution of STEP-NC of the
CNC manufacturing activities. The paper concludes with discussion
of the applications in this particular area.
Abstract: In this paper, a novel method for recognition of musical
instruments in a polyphonic music is presented by using an
embedded hidden Markov model (EHMM). EHMM is a doubly
embedded HMM structure where each state of the external HMM
is an independent HMM. The classification is accomplished for
two different internal HMM structures where GMMs are used as
likelihood estimators for the internal HMMs. The results are compared
to those achieved by an artificial neural network with two
hidden layers. Appropriate classification accuracies were achieved
both for solo instrument performance and instrument combinations
which demonstrates that the new approach outperforms the similar
classification methods by means of the dynamic of the signal.
Abstract: Certain tRNA synthetases have developed highly accurate molecular machinery to discriminate their cognate amino acids. Those aaRSs achieve their goal via editing reaction in the Connective Polypeptide 1 (CP1). Recently mutagenesis studies have revealed the critical importance of residues in the CP1 domain for editing activity and X-ray structures have shown binding mode of noncognate amino acids in the editing domain. To pursue molecular mechanism for amino acid discrimination, molecular modeling studies were performed. Our results suggest that aaRS bind the noncognate amino acid more tightly than the cognate one. Finally, by comparing binding conformations of the amino acids in three systems, the amino acid binding mode was elucidated and a discrimination mechanism proposed. The results strongly reveal that the conserved threonines are responsible for amino acid discrimination. This is achieved through side chain interactions between T252 and T247/T248 as well as between those threonines and the incoming amino acids.
Abstract: Losses reduction initiatives in distribution systems
have been activated due to the increasing cost of supplying
electricity, the shortage in fuel with ever-increasing cost to produce
more power, and the global warming concerns. These initiatives have
been introduced to the utilities in shape of incentives and penalties.
Recently, the electricity distribution companies in Oman have been
incentivized to reduce the distribution technical and non-technical
losses with an equal annual reduction rate for 6 years. In this paper,
different techniques for losses reduction in Mazoon Electricity
Company (MZEC) are addressed. In this company, high numbers of
substation and feeders were found to be non-compliant with the
Distribution System Security Standard (DSSS). Therefore, 33
projects have been suggested to bring non-complying 29 substations
and 28 feeders to meet the planed criteria and to comply with the
DSSS. The largest part of MZEC-s network (South Batinah region)
was modeled by ETAP software package. The model has been
extended to implement the proposed projects and to examine their
effects on losses reduction. Simulation results have shown that the
implementation of these projects leads to a significant improvement
in voltage profile, and reduction in the active and the reactive power
losses. Finally, the economical analysis has revealed that the
implementation of the proposed projects in MZEC leads to an annual
saving of about US$ 5 million.
Abstract: Many researchers are working on information hiding
techniques using different ideas and areas to hide their secrete data.
This paper introduces a robust technique of hiding secret data in
image based on LSB insertion and RSA encryption technique. The
key of the proposed technique is to encrypt the secret data. Then the
encrypted data will be converted into a bit stream and divided it into
number of segments. However, the cover image will also be divided
into the same number of segments. Each segment of data will be
compared with each segment of image to find the best match
segment, in order to create a new random sequence of segments to be
inserted then in a cover image. Experimental results show that the
proposed technique has a high security level and produced better
stego-image quality.
Abstract: The link between coordinate transformations in the plane and their effects on the graph of a function can be difficult for students studying college level mathematics to comprehend. To solidify this conceptual link in the mind of a student Microsoft Excel can serve as a convenient graphing tool and pedagogical aid. The authors of this paper describe how various transformations and their related functional symmetry properties can be graphically displayed with an Excel spreadsheet.
Abstract: Internal controls of accounting are an essential
business function for a growth-oriented organization, and include the
elements of risk assessment, information communications and even
employees' roles and responsibilities. Internal controls of accounting
systems are designed to protect a company from fraud, abuse and
inaccurate data recording and help organizations keep track of
essential financial activities. Internal controls of accounting provide a
streamlined solution for organizing all accounting procedures and
ensuring that the accounting cycle is completed consistently and
successfully. Implementing a formal Accounting Procedures Manual
for the organization allows the financial department to facilitate
several processes and maintain rigorous standards. Internal controls
also allow organizations to keep detailed records, manage and
organize important financial transactions and set a high standard for
the organization's financial management structure and protocols. A
well-implemented system also reduces the risk of accounting errors
and abuse. A well-implemented controls system allows a company's
financial managers to regulate and streamline all functions of the
accounting department. Internal controls of accounting can be set up
for every area to track deposits, monitor check handling, keep track
of creditor accounts, and even assess budgets and financial statements
on an ongoing basis. Setting up an effective accounting system to
monitor accounting reports, analyze records and protect sensitive
financial information also can help a company set clear goals and
make accurate projections. Creating efficient accounting processes
allows an organization to set specific policies and protocols on
accounting procedures, and reach its financial objectives on a regular
basis. Internal accounting controls can help keep track of such areas
as cash-receipt recording, payroll management, appropriate recording
of grants and gifts, cash disbursements by authorized personnel, and
the recording of assets. These systems also can take into account any
government regulations and requirements for financial reporting.
Abstract: The effect of wood vinegar, entomopathogenic
nematodes ((Steinernema thailandensis n. sp.) and fermented organic
substances from four plants such as: Derris elliptica Roxb, Stemona
tuberosa Lour, Tinospora crispa Mier and Azadirachta indica J. were
tested on the five varieties of sweetpotato with potential for
bioethanol production ie. Taiwan, China, PROC No.65-16, Phichit
166-5, and Phichit 129-6. The experimental plots were located at
Faculty of Agriculture, Natural Resources and Environment,
Naresuan University, Phitsanulok, Thailand. The aim of this study
was to compare the efficiency of the five treatments for growth, yield
and insect infestation on the five varieties of sweetpotato. Treatment
with entomopathogenic nematodes gave the highest average weight
of sweetpotato tubers (1.3 kg/tuber), followed by wood vinegar,
fermented organic substances and mixed treatment with yields of
0.88, 0.46 and 0.43 kg/tuber, respectively. Also the
entomopathogenic nematode treatment gave significantly higher
average width and length of sweet potato (9.82 cm and 9.45 cm,
respectively). Additionally, the entomopathogenic nematode
provided the best control of insect infestation on sweetpotato leaves
and tubers. Comparison among the varieties of sweetpotato, PROC
NO.65-16 showed the highest weight and length. However, Phichit
129-6 gave significantly higher weight of 0.94 kg/tuber. Lastly, the
lowest sweet potato weevil infestation on leaves and tubers occurred
on Taiwan and Phichit 129-6.
Abstract: In this paper, low end Digital Signal Processors (DSPs)
are applied to accelerate integer neural networks. The use of DSPs
to accelerate neural networks has been a topic of study for some
time, and has demonstrated significant performance improvements.
Recently, work has been done on integer only neural networks, which
greatly reduces hardware requirements, and thus allows for cheaper
hardware implementation. DSPs with Arithmetic Logic Units (ALUs)
that support floating or fixed point arithmetic are generally more
expensive than their integer only counterparts due to increased circuit
complexity. However if the need for floating or fixed point math
operation can be removed, then simpler, lower cost DSPs can be
used. To achieve this, an integer only neural network is created in
this paper, which is then accelerated by using DSP instructions to
improve performance.
Abstract: SEMG (Surface Electromyogram) is one of the
bio-signals and is generated from the muscle. And there are many
research results that use forearm EMG to detect hand motions. In this
paper, we will talk about our developed the robot hand system that can
control grasping power by SEMG. In our system, we suppose that
muscle power is proportional to the amplitude of SEMG. The power is
estimated and the grip power of a robot hand is able to be controlled
using estimated muscle power in our system. In addition, to perform a
more precise control can be considered to build a closed loop feedback
system as an object to a subject to pressure from the edge of hand. Our
objectives of this study are the development of a method that makes
perfect detection of the hand grip force possible using SEMG patterns,
and applying this method to the man-machine interface.
Abstract: The goal of this research is discovering the
determinants of the success or failure of external cooperation in small
and medium enterprises (SMEs). For this, a survey was given to 190
SMEs that experienced external cooperation within the last 3 years. A
logistic regression model was used to derive organizational or strategic
characteristics that significantly influence whether external
collaboration of domestic SMEs is successful or not. Results suggest
that research and development (R&D) features in general
characteristics (both idea creation and discovering market
opportunities) that focused on and emphasized indirected-market
stakeholders (such as complementary companies and affiliates) and
strategies in innovative strategic characteristics raise the probability of
successful external cooperation. This can be used meaningfully to
build a policy or strategy for inducing successful external cooperation
or to understand the innovation of SMEs.