Abstract: Synthesis gas manufacturing by steam reforming of hydrocarbons is an important industrial process. High endothermic nature of the process makes it one of the most cost and heat intensive processes. In the present work, composite effect of different inert gases on synthesis gas yield, feed gas conversion and temperature distribution along the reactor length has been studied using a heterogeneous model. Mathematical model was developed as a first stage and validated against the existing process models. With the addition of inert gases, a higher yield of synthesis gas is observed. Simultaneously the rector outlet temperature drops to as low as 810 K. It was found that Xenon gives the highest yield and conversion while Helium gives the lowest temperature. Using Xenon inert gas 20 percent reduction in outlet temperature was observed compared to traditional case.
Abstract: Influence of octane and benzene on plant cell
ultrastructure and enzymes of basic metabolism, such as nitrogen
assimilation and energy generation have been studied. Different
plants: perennial ryegrass (Lolium perenne) and alfalfa (Medicago
sativa); crops- maize (Zea mays L.) and bean (Phaseolus vulgaris);
shrubs – privet (Ligustrum sempervirens) and trifoliate orange
(Poncirus trifoliate); trees - poplar (Populus deltoides) and white
mulberry (Morus alba L.) were exposed to hydrocarbons of different
concentrations (1, 10 and 100 mM). Destructive changes in bean and
maize leaves cells ultrastructure under the influence of benzene
vapour were revealed at the level of photosynthetic and energy
generation subcellular organells. Different deviations at the level of
subcellular organelles structure and distribution were observed in
alfalfa and ryegrass root cells under the influence of benzene and
octane, absorbed through roots. The level of destructive changes is
concentration dependent. Benzene at low 1 and 10 mM concentration
caused the increase in glutamate dehydrogenase (GDH) activity in
maize roots and leaves and in poplar and mulberry shoots, though to
higher extent in case of lower, 1mM concentration. The induction
was more intensive in plant roots. The highest tested 100mM
concentration of benzene was inhibitory to the enzyme in all plants.
Octane caused induction of GDH in all grassy plants at all tested
concentrations; however the rate of induction decreased parallel to
increase of the hydrocarbon concentration. Octane at concentration 1
mM caused induction of GDH in privet, trifoliate and white mulberry
shoots. The highest, 100mM octane was characterized by inhibitory
effect to GDH activity in all plants. Octane had inductive effect on
malate dehydrogenase in almost all plants and tested concentrations,
indicating the intensification of Trycarboxylic Acid Cycle.
The data could be suggested for elaboration of criteria for plant
selection for phytoremediation of oil hydrocarbons contaminated
soils.
Abstract: The adsorption properties of CO and H2 on iron-based
catalyst with addition of Zr and Ni were investigated using
temperature programmed desorption process. It was found that on the
carburized iron-based catalysts, molecular state and dissociative state
CO existed together. The addition of Zr was preferential for the
molecular state adsorption of CO on iron-based catalyst and the
presence of Ni was beneficial to the dissociative adsorption of CO. On
H2 reduced catalysts, hydrogen mainly adsorbs on the surface iron
sites and surface oxide sites. On CO reduced catalysts, hydrogen
probably existed as the most stable CH and OH species. The addition
of Zr was not benefit to the dissociative adsorption of hydrogen on
iron-based catalyst and the presence of Ni was preferential for the
dissociative adsorption of hydrogen.
Abstract: HSDPA is a new feature which is introduced in
Release-5 specifications of the 3GPP WCDMA/UTRA standard to
realize higher speed data rate together with lower round-trip times.
Moreover, the HSDPA concept offers outstanding improvement of
packet throughput and also significantly reduces the packet call
transfer delay as compared to Release -99 DSCH. Till now the
HSDPA system uses turbo coding which is the best coding technique
to achieve the Shannon limit. However, the main drawbacks of turbo
coding are high decoding complexity and high latency which makes
it unsuitable for some applications like satellite communications,
since the transmission distance itself introduces latency due to
limited speed of light. Hence in this paper it is proposed to use LDPC
coding in place of Turbo coding for HSDPA system which decreases
the latency and decoding complexity. But LDPC coding increases the
Encoding complexity. Though the complexity of transmitter
increases at NodeB, the End user is at an advantage in terms of
receiver complexity and Bit- error rate. In this paper LDPC Encoder
is implemented using “sparse parity check matrix" H to generate a
codeword at Encoder and “Belief Propagation algorithm "for LDPC
decoding .Simulation results shows that in LDPC coding the BER
suddenly drops as the number of iterations increase with a small
increase in Eb/No. Which is not possible in Turbo coding. Also same
BER was achieved using less number of iterations and hence the
latency and receiver complexity has decreased for LDPC coding.
HSDPA increases the downlink data rate within a cell to a theoretical
maximum of 14Mbps, with 2Mbps on the uplink. The changes that
HSDPA enables includes better quality, more reliable and more
robust data services. In other words, while realistic data rates are
only a few Mbps, the actual quality and number of users achieved
will improve significantly.
Abstract: A Rotary Disc Contactor with inner diameter of
9.1cm and maximum operating height of 40cm has been used to
investigate break up phenomenon. Water-Toluene, Water as
continuous phase and Toluene as dispersed phase, was selected as
chemical system in the experiments. The mentioned chemical system
has high interfacial tension so it was possible to form big drops
which permit accurate investigation on break up phenomenon as well
as the first and second critical rotor speeds.
In this study, Break up phenomenon has been studied as a function
of mother drop size, rotor speed and continuous phase height. Further
more; the effects of mother drop size and continuous phase height on
the first and second critical rotor speeds were investigated. Finally,
two modified correlations were proposed to estimate the first and
second critical speeds.
Abstract: The evaluation of non-conventional water resources
on seed germination and seedling growth performance at early
growth stages is still in progress especially in forage crops. This
study was designed to test the effect of four types of water qualities
(treated wastewater (TWW), industrial water (IW), grey water (GW),
and Distilled water (DW)) on germination and early seedling vigor of
Leucaena leucocephala. The results showed that the germination
was not significantly affected by the different water qualities. Seed
germination reached maximum after 17, 14, 14, and 21 days under
GW, IW, TWW, and DW treatments, respectively. The highest mean
of shoot length was scored under the GW treatment. And, the highest
mean of root length was scored under DW which was not significant
from GW treatment. The means of shoot fresh was the highest under
the TWW. The means of root fresh weight was not significantly
different from each other's under different treatments. The growth
performance was in progress with no mortality during 21 days of
growth. Thus, the best non-conventional water qualities alternatives
based on the cleanness, nutrients, and toxicity are the GW, TWW and
IW, respectively.
Abstract: Using finite element method (FEM), the elastic
new strain-concentration factor (SNCF) of cylindrical bars
with circumferential flat-bottom groove is studied. This new
SNCF has been defined under triaxial stress state. The
employed specimens have constant groove depth with net
section and gross diameters of 10.0 and 16.7 mm,
respectively. The length of flatness ao has been varied form
0.0 ~12.5 mm to study the elastic SNCF of this type of
geometrical irregularities. The results that the elastic new
SNCF rapidly drops from its elastic value of the groove with
ao = 0.0, i.e. circumferential U-notch, and reaches minimum
value at ao = 2 mm. After that the elastic new SNCF becomes
nearly constant with increasing flatness length (ao). The value
of tensile load at yielding at the groove root increases with
increasing ao. The current results show that severity of the
notch decreases with increasing flatness length ao.
Abstract: India is currently the second most populous nation in
the world with over 1.2 billion people, growing annually at the rate of
1.5%. It is experiencing a surge in energy demands, expected to grow
more than three to four times in 25 years. Most of the energy
requirements are currently satisfied by the import of fossil fuels –
coal, petroleum-based products and natural gas. Biofuels can satisfy
these energy needs in an environmentally benign and cost effective
manner while reducing dependence on import of fossil fuels, thus
providing National Energy Security. Among various forms of
bioenergy, bioethanol is one of the major options for India because of
availability of feed stock crops.
This paper presents an overview on bioethanol production and
technology, steps taken by the Indian government to facilitate and
bring about optimal development and utilization of indigenous
biomass feedstocks for production of this biofuel.
Abstract: The National Agricultural Biotechnology Information
Center (NABIC) plays a leading role in the biotechnology information
database for agricultural plants in Korea. Since 2002, we have
concentrated on functional genomics of major crops, building an
integrated biotechnology database for agro-biotech information that
focuses on bioinformatics of major agricultural resources such as rice,
Chinese cabbage, and microorganisms. In the NABIC,
integration-based biotechnology database provides useful information
through a user-friendly web interface that allows analysis of genome
infrastructure, multiple plants, microbial resources, and living
modified organisms.
Abstract: The mechanism of abiotic stress tolerance is crucial
for plants to survive in harsh condition and the knowledge of this
mechanism can be use to solve the problem of declining productivity
of plants or crops around the world. However in-depth description is
still unclear and it is argued, in particular that there is a relationship
between high salinity tolerance and the ability to tolerate high light
condition. In this study, Dunaliella salina, which can withstand high
salt was used as a model. Chlorophyll fluorometer for nonphotochemical
quenching (NPQ) measurement and high-performance
liquid chromatography for pigment determination was used. The
results show that NPQ value and the amount of pigment were
increased along with the levels of salinity. However, it establish a
clear relationship between high salt and high light but the further
study to optimized the solutions mentioned above is still required.
Abstract: In this paper, a new approach based on the extent of
friendship between the nodes is proposed which makes the nodes to
co-operate in an ad hoc environment. The extended DSR protocol is
tested under different scenarios by varying the number of malicious
nodes and node moving speed. It is also tested varying the number of
nodes in simulation used. The result indicates the achieved
throughput by extended DSR is greater than the standard DSR and
indicates the percentage of malicious drops over total drops are less
in the case of extended DSR than the standard DSR.
Abstract: Agriculture is one of the single largest sectors of Bangladesh economy. Bangladesh is an agro based country and predominantly is an agrarian economy. It is the backbone of the economy of Bangladesh. Around 75% of the total population directly or indirectly depends on agriculture and near about 84% of the total population lives in rural areas almost depend on agriculture for livelihood. Agriculture includes the sub-sectors of crop, livestock, forestry and fisheries. The contribution of all sub sectors is around 22.83 percent to national GDP in 2003-2004. The crops sub sector alone contributes 12.94 percent of GDP.
Abstract: Moisture is an important consideration in many
aspects ranging from irrigation, soil chemistry, golf course, corrosion
and erosion, road conditions, weather predictions, livestock feed
moisture levels, water seepage etc. Vegetation and crops always
depend more on the moisture available at the root level than on
precipitation occurrence. In this paper, design of an instrument is
discussed which tells about the variation in the moisture contents of
soil. This is done by measuring the amount of water content in soil by
finding the variation in capacitance of soil with the help of a
capacitive sensor. The greatest advantage of soil moisture sensor is
reduced water consumption. The sensor is also be used to set lower
and upper threshold to maintain optimum soil moisture saturation and
minimize water wilting, contributes to deeper plant root growth
,reduced soil run off /leaching and less favorable condition for insects
and fungal diseases. Capacitance method is preferred because, it
provides absolute amount of water content and also measures water
content at any depth.
Abstract: Coal will continue to be the predominant source of
global energy for coming several decades. The huge generation of fly
ash (FA) from combustion of coal in thermal power plants (TPPs) is
apprehended to pose the concerns of its disposal and utilization. FA
application based on its typical characteristics as soil ameliorant for
agriculture and forestry is the potential area, and hence the global
attempt. The inferences drawn suffer from the variations of ash
characteristics, soil types, and agro-climatic conditions; thereby
correlating the effects of ash between various plant species and soil
types is difficult. Indian FAs have low bulk density, high water
holding capacity and porosity, rich silt-sized particles, alkaline
nature, negligible solubility, and reasonable plant nutrients. Findings
of the demonstrations trials for more than two decades from lab/pot
to field scale long-term experiments are developed as FA soil
amendment technology (FASAT) by Central Institute of Mining and
Fuel Research (CIMFR), Dhanbad. Performance of different crops
and plant species in cultivable and problematic soils, are
encouraging, eco-friendly, and being adopted by the farmers. FA
application includes ash alone and in combination with
inorganic/organic amendments; combination treatments including
bio-solids perform better than FA alone. Optimum dose being up to
100 t/ha for cultivable land and up to/ or above 200 t/ha of FA for
waste/degraded land/mine refuse, depending on the characteristics of
ash and soil. The elemental toxicity in Indian FA is usually not of
much concern owing to alkaline ashes, oxide forms of elements, and
elemental concentration within the threshold limits for soil
application. Combating toxicity, if any, is possible through
combination treatments with organic materials and phytoremediation.
Government initiatives through extension programme
involving farmers and ash generating organizations need to be
accelerated
Abstract: The objective of this research is to study principal
component analysis for classification of 67 soil samples collected from
different agricultural areas in the western part of Thailand. Six soil
properties were measured on the soil samples and are used as original
variables. Principal component analysis is applied to reduce the
number of original variables. A model based on the first two
principal components accounts for 72.24% of total variance. Score
plots of first two principal components were used to map with
agricultural areas divided into horticulture, field crops and wetland.
The results showed some relationships between soil properties and
agricultural areas. PCA was shown to be a useful tool for agricultural
areas classification based on soil properties.
Abstract: In this study, a reformer model simulation to use
refinery (Farashband refinery, Iran) waste natural gas. In the
petroleum and allied sectors where natural gas is being encountered
(in form of associated gas) without prior preparation for its positive
use, its combustion (which takes place in flares, an equipment through
which they are being disposed) has become a great problem because
of its associated environmental problems in form of gaseous emission.
The proposed model is used to product syngas from waste natural gas.
A detailed steady model described by a set of ordinary differential and
algebraic equations was developed to predict the behavior of the
overall process. The proposed steady reactor model was validated
against process data of a reformer synthesis plant recorded and a good
agreement was achieved. H2/CO ratio has important effect on Fischer-
Tropsch synthesis reactor product and we try to achieve this parameter
with best designing reformer reactor. We study different kind of
reformer reactors and then select auto thermal reforming process of
natural gas in a fixed bed reformer that adjustment H2/CO ratio with
CO2 and H2O injection. Finally a strategy was proposed for prevention
of extra natural gas to atmosphere.
Abstract: With the growth of electricity generation from gas
energy gas pipeline reliability can substantially impact the electric
generation. A physical disruption to pipeline or to a compressor
station can interrupt the flow of gas or reduce the pressure and lead
to loss of multiple gas-fired electric generators, which could
dramatically reduce the supplied power and threaten the power
system security. Gas pressure drops during peak loading time on
pipeline system, is a common problem in network with no enough
transportation capacity which limits gas transportation and causes
many problem for thermal domain power systems in supplying their
demand. For a feasible generation scheduling planning in networks
with no sufficient gas transportation capacity, it is required to
consider gas pipeline constraints in solving the optimization problem
and evaluate the impacts of gas consumption in power plants on gas
pipelines operating condition. This paper studies about operating of
gas fired power plants in critical conditions when the demand of gas
and electricity peak together. An integrated model of gas and electric
model is used to consider the gas pipeline constraints in the economic
dispatch problem of gas-fueled thermal generator units.
Abstract: Yield and Crop Water Productivity are crucial issues
in sustainable agriculture, especially in high-demand resource crops such as sweet corn. This study was conducted to investigate
agronomic responses such as plant growth, yield and soil parameters (EC and Nitrate accumulation) to several deficit irrigation treatments
(100, 75, 50, 25 and 0% of ETm) applied during vegetative growth
stage, rainfed treatment was also tested.
The finding of this research indicates that under deficit irrigation
during vegetative growth stage applying 75% of ETm lead to increasing of 19.4% in terms of fresh ear yield, 9.4% in terms of dry grain yield, 10.5% in terms of number of ears per plant, 11.5% for
the 1000 grains weight and 19% in terms of crop water productivity compared with fully irrigated treatment. While those parameters in
addition to root, shoot and plant height has been affected by deficit
irrigation during vegetative growth stage when increasing water stress degree more than 50% of ETm.
Abstract: Insect pests are the major source of crop
damage, yield and quality reduction in Pakistan and else
where in the world. Cotton crop is the most hit crop in
Pakistan followed by rice and the second most important
foreign exchange earning crop. A wide variety of staple,
horticultural and cash crops grown, reflect serious problems of
many types of insect pests. To overcome the insect pest
problem, pesticide use in Pakistan has increased substantially
which has now been further intensified. Pesticides worth more
than billions of rupees are imported every year. This paper
reviews the over all pesticide use in Pakistan in relation to
pesticide prices, support price of cotton and rice, pesticide use
in different provinces of Pakistan on different crops and their
impact on crop productivity. The environmental pollution
caused by the use of pesticides, contamination of soil and
water resources and the danger associated with the disposal of
their empty containers is also discussed in detail.
Abstract: Salinity level may affect early development of
biofuel feedstock crops. The biofuel feedstock crops canola
(Brassica napus L.), sorghum [Sorghum bicolor (L.) Moench], and
sunflower (Helianthus annuus L.); and the potential feedstock crop
sweet corn (Zea mays L.) were planted in media in pots and treated
with aqueous solutions of 0, 0.1, 0.5 and 1.0 M NaCl once at: 1)
planting; 2) 7-10 days after planting or 3) first true leaf expansion.
An additional treatment (4) comprised of one-half strength of the 0.1,
0.5 and 1.0 M (concentrations 0.05, 0.25, 0.5 M at each application)
was applied at first true leaf expansion and four days later. Survival
of most crops decreased below 90% above 0.5 M; survival of canola
decreased above 0.1 M. Application timing had little effect on crop
survival. For canola root fresh and dry weights improved when
application was at plant emergence; for sorghum top and root fresh
weights improved when the split application was used. When
application was at planting root dry weight was improved over most
other applications. Sunflower top fresh weight was among the
highest when saline solutions were split and top dry weight was
among the highest when application was at plant emergence. Sweet
corn root fresh weight was improved when the split application was
used or application was at planting. Sweet corn root dry weight was
highest when application was at planting or plant emergence. Even at
high salinity rates survival rates greater than what might be expected
occurred. Plants that survived appear to be able to adjust to saline
during the early stages of development.