Abstract: The electrolyte stirring method of anodization etching
process for manufacturing porous silicon (PS) is reported in this work.
Two experimental setups of nature air stirring (PS-ASM) and
electrolyte stirring (PS-ESM) are employed to clarify the influence of
stirring mechanisms on electrochemical etching process. Compared to
traditional fabrication without any stirring apparatus (PS-TM), a large
plateau region of PS surface structure is obtained from samples with
both stirring methods by the 3D-profiler measurement. Moreover, the
light emission response is also improved by both proposed electrolyte
stirring methods due to the cycling force in electrolyte could
effectively enhance etch-carrier distribution while the electrochemical
etching process is made. According to the analysis of statistical
calculation of photoluminescence (PL) intensity, lower standard
deviations are obtained from PS-samples with studied stirring methods,
i.e. the uniformity of PL-intensity is effectively improved. The
calculated deviations of PL-intensity are 93.2, 74.5 and 64,
respectively, for PS-TM, PS-ASM and PS-ESM.
Abstract: This paper presents an intelligent speed control
system based on fuzzy logic for a voltage source PWM inverter-fed
indirect vector controlled induction motor drive. Traditional indirect
vector control system of induction motor introduces conventional PI
regulator in outer speed loop; it is proved that the low precision of the
speed regulator debases the performance of the whole system. To
overcome this problem, replacement of PI controller by an intelligent
controller based on fuzzy set theory is proposed. The performance of
the intelligent controller has been investigated through digital
simulation using MATLAB-SIMULINK package for different
operating conditions such as sudden change in reference speed and
load torque. The simulation results demonstrate that the performance
of the proposed controller is better than that of the conventional PI
controller.
Abstract: The potential of economically cheaper cellulose
containing natural materials like rice husk was assessed for nickel
adsorption from aqueous solutions. The effects of pH, contact time,
sorbent dose, initial metal ion concentration and temperature on the
uptake of nickel were studied in batch process. The removal of nickel
was dependent on the physico-chemical characteristics of the
adsorbent, adsorbate concentration and other studied process
parameters. The sorption data has been correlated with Langmuir,
Freundlich and Dubinin-Radush kevich (D-R) adsorption models. It
was found that Freundlich and Langmuir isotherms fitted well to the
data. Maximum nickel removal was observed at pH 6.0. The
efficiency of rice husk for nickel removal was 51.8% for dilute
solutions at 20 g L-1 adsorbent dose. FTIR, SEM and EDAX were
recorded before and after adsorption to explore the number and
position of the functional groups available for nickel binding on to
the studied adsorbent and changes in surface morphology and
elemental constitution of the adsorbent. Pseudo-second order model
explains the nickel kinetics more effectively. Reusability of the
adsorbent was examined by desorption in which HCl eluted 78.93%
nickel. The results revealed that nickel is considerably adsorbed on
rice husk and it could be and economic method for the removal of
nickel from aqueous solutions.
Abstract: The aim of this study is to discuss the relationship between tourist awareness of environmental issues and their own recreational behaviors in the Taipei Guandu Wetland. A total of 392 questionnaires were gathered for data analysis using descriptive statistics, t-testing, one-way analysis of variance (ANOVA) and least significant difference (LSD) post hoc comparisons. The results showed that most of the visitors there enjoying the beautiful scenery are 21 to 30 years old with a college education. The means and standard deviations indicate that tourists express a positive degree of cognition of environmental issues and recreational behaviors. They suggest that polluting the environment is harmful to the natural ecosystem and that the natural resources of ecotourism are fragile, as well as expressing a high degree of recognition of the need to protect wetlands. Most of respondents are cognizant of the regulations proposed by the Guandu Wetland administration which asks that users exercise self-control and follow recommended guidelines when traveling the wetland. There were significant differences in the degree of cognition related to the variables of age, number of visits and reasons for visiting. We found that most respondents with relatively high levels of education would like to learn more about the wetland and are supportive of its conservation.
Abstract: In this paper, a novel deinterlacing algorithm is
proposed. The proposed algorithm approximates the distribution of the
luminance into a polynomial function. Instead of using one
polynomial function for all pixels, different polynomial functions are
used for the uniform, texture, and directional edge regions. The
function coefficients for each region are computed by matrix
multiplications. Experimental results demonstrate that the proposed
method performs better than the conventional algorithms.
Abstract: In this article, using finite element analysis (FEA)
and an X-ray diffractometer (XRD), cold-sprayed titanium particles
on a steel substrate is investigated in term of cooling time and the
development of residual strains. Three cooling-down models of
sprayed particles after deposition stage are simulated and discussed:
the first model (m1) considers conduction effect to the substrate only,
the second model (m2) considers both conduction as well as
convection effect to the environment, and the third model (m3) which
is the same as the second model but with the substrate heated to a
near particle temperature before spraying. Thereafter, residual strains
developed in the third model is compared with the experimental
measurement of residual strains, which involved a Bruker D8
Advance Diffractometer using CuKa radiation (40kV, 40mA)
monochromatised with a graphite sample monochromator. For
deposition conditions of this study, a good correlation was found to
exist between the FEA results and XRD measurements of residual
strains.
Abstract: Since polymerase chain reaction (PCR) has been
invented, it has emerged as a powerful tool in genetic analysis. The
PCR products are closely linked with thermal cycles. Therefore, to
reduce the reaction time and make temperature distribution uniform in
the reaction chamber, a novel oscillatory thermal cycler is designed.
The sample is placed in a fixed chamber, and three constant isothermal
zones are established and lined in the system. The sample is oscillated
and contacted with three different isothermal zones to complete
thermal cycles. This study presents the design of the geometric
characteristics of the chamber. The commercial software
CFD-ACE+TM is utilized to investigate the influences of various
materials, heating times, chamber volumes, and moving speed of the
chamber on the temperature distributions inside the chamber. The
chamber moves at a specific velocity and the boundary conditions
with time variations are related to the moving speed. Whereas the
chamber moves, the boundary is specified at the conditions of the
convection or the uniform temperature. The user subroutines compiled
by the FORTRAN language are used to make the numerical results
realistically. Results show that the reaction chamber with a rectangular
prism is heated on six faces; the effects of various moving speeds of
the chamber on the temperature distributions are examined. Regarding
to the temperature profiles and the standard deviation of the
temperature at the Y-cut cross section, the non-uniform temperature
inside chamber is found as the moving speed is larger than 0.01 m/s.
By reducing the heating faces to four, the standard deviation of the
temperature of the reaction chamber is under 1.4×10-3K with the range
of velocities between 0.0001 m/s and 1 m/s. The nature convective
boundary conditions are set at all boundaries while the chamber moves
between two heaters, the effects of various moving velocities of the
chamber on the temperature distributions are negligible at the assigned
time duration.
Abstract: We address the problem of joint beamforming and multipath channel parameters estimation in Wideband Code Division Multiple Access (WCDMA) communication systems that employ Multiple-Access Interference (MAI) suppression techniques in the uplink (from mobile to base station). Most of the existing schemes rely on time multiplex a training sequence with the user data. In WCDMA, the channel parameters can also be estimated from a code multiplexed common pilot channel (CPICH) that could be corrupted by strong interference resulting in a bad estimate. In this paper, we present new methods to combine interference suppression together with channel estimation when using multiple receiving antennas by using adaptive signal processing techniques. Computer simulation is used to compare between the proposed methods and the existing conventional estimation techniques.
Abstract: The autonomic nervous system has a regulatory
structure that helps people adapt to changes in their environment by
adjusting or modifying some functions in response to stress, and regulating involuntary function of human organs. The purpose of this
study was to investigate the effect of combined stimulation, both
far-infrared heating and chiropractic, on the autonomic nervous system
activities using thermal image and heart rate variability. Six healthy subjects participated in this test. We compared the before and after
autonomic nervous system activities through obtaining thermal image
and photoplethysmogram signal. The thermal images showed that the
combined stimulation changed subject-s body temperature more
highly and widely than before. The result of heart rate variability
indicated that LF/HF ratio decreased. We concluded that combined
stimulation activates autonomic nervous system, and expected other
possibilities of this combined stimulation.
Abstract: Five original strains of entomopathogenic bacteria
with insecticidal activity against mosquito larvae of the genera Aedes,
Culex and Anopheles have been isolated from natural conditions in
Armenia and characterized. According to morphological,
physiological and biochemical parameters, all isolates were identified
as Bacillus thuringiensis spp. israelensis (Bti). High larvicidal
activity has been showed by three strains Bti. These strains can be
recommended for industrial production of bacterial preparations.
Abstract: Supplementation of palm vitamin E has been reported
to prevent loss of bone density in ovariectomised female rats. The
mechanism by which palm vitamin E exerts these effects is still
unknown. We hypothesized that palm vitamin E may act by
preventing the protein expression changes. Two dimensional poly
acyrilamide gel electrophoresis (2-D PAGE) and PD Quest software
genomic solutions Investigator (proteomics) was used to analyze the
differential protein expression profile in femoral and humeri bones
harvested from three groups of rats; sham-operated rats (SO),
ovariectomised rats (Ovx) and ovariectomised rats supplemented for
2 months with palm vitamin E. The results showed that there were
over 300 valued spot on each of the groups PVE and OVX as
compared to about 200 in SO. Comparison between the differential
protein expression between OVX and PVE groups showed that ten
spots were down –regulated in OVX but up-regulated in PVE. The
ten differential spots were separately named P1-P10. The
identification and understanding of the pathway of the differential
protein expression among the groups is ongoing and may account for
the molecular mechanism through which palm vitamin E exert its
anti-osteoporotic effect.
Abstract: Traffic enforcement units (the Police) are partly
responsible for the severity and frequency of the traffic accidents via
the effectiveness of their safety measures. The Police claims that the
reductions in accidents and their severities occur largely by their
timely interventions at the black spots, through traffic management
or temporary changes in the road design (guiding, reducing speeds
and eliminating sight obstructions, etc.). Yet, some other external
factors than the Police measures may intervene into which such
claims require a statistical confirmation. In order to test the net
impact of the Police contribution in the reduction of the number of
crashes, Chi square test was applied for 25 spots (streets and
intersections) and an average evaluation was achieved for general
conclusion in the case study of Izmir city. Separately, the net impact
of economic crisis in the reduction of crashes is assessed by the
trend analysis for the case of the economic crisis with the probable
reduction effects on the trip generation or modal choice. Finally, it
was proven that the Police measures were effective to some degree as
they claimed, though the economic crisis might have only negligible
contribution to the reductions in the same period observed.
Abstract: The notion of communicative competence has been deemed fuzzy in communication studies. This fuzziness has led to tensions among engineers across tenures in interpreting what constitutes communicative competence. The study seeks to investigate novice and professional engineers- understanding of the said notion in terms of two main elements of communicative competence: linguistic and rhetorical competence. Novice engineers are final year engineering students, whilst professional engineers represent engineers who have at least 5 years working experience. Novice and professional engineers were interviewed to gauge their perceptions on linguistic and rhetorical features deemed necessary to enhance communicative competence for the profession. Both groups indicated awareness and differences on the importance of the sub-sets of communicative competence, namely, rhetorical explanatory competence, linguistic oral immediacy competence, technical competence and meta-cognitive competence. Such differences, a possible attribute of the learning theory, inadvertently indicate sublime differences in the way novice and professional engineers perceive communicative competence.
Abstract: This paper presents a solution for ceramic cutting tools availability in interrupted machining. Experiments were performed on a special fixture – the interrupted cut simulator. This fixture was constructed at our Department of Machining and Assembly within the scope of a project by the Czech Science Foundation. The goals of the tests were to contribute to the wider usage of these cutting materials in machining, especially in interrupted machining. Through the centuries, producers of ceramic cutting tools have taken big steps forward. Namely, increasing durability in maintaining high levels of strength and hardness lends an advantage. Some producers of these materials advise cutting inserts for interrupted machining at the present time [1, 2].
Abstract: Serial Analysis of Gene Expression is a powerful
quantification technique for generating cell or tissue gene expression
data. The profile of the gene expression of cell or tissue in several
different states is difficult for biologists to analyze because of the large
number of genes typically involved. However, feature selection in
machine learning can successfully reduce this problem. The method
allows reducing the features (genes) in specific SAGE data, and
determines only relevant genes. In this study, we used a genetic
algorithm to implement feature selection, and evaluate the
classification accuracy of the selected features with the K-nearest
neighbor method. In order to validate the proposed method, we used
two SAGE data sets for testing. The results of this study conclusively
prove that the number of features of the original SAGE data set can be
significantly reduced and higher classification accuracy can be
achieved.
Abstract: Twenty seven tektites from the Wenchang area, Hainan
province (south China) and five tektites from the Khon Kaen area
(northeast Thailand) were analyzed for major and trace element
contents and Rb-Sr isotopic compositions. All the samples studied are
splash-form tektites. Tektites of this study are characterized by high
SiO2 contents ranging from 71.95 to 74.07 wt% which is consistent
with previously published analyses of Australasian tektites. The trace
element ratios Ba/Rb (avg. 3.89), Th/Sm (avg. 2.40), Sm/Sc (avg.
0.45), Th/Sc (avg. 0.99) and the rare earth elements (REE) contents of
tektites of this study are similar to the average upper continental crust.
Based on the chemical composition, it is suggested that tektites in this
study are derived from similar parental material and are similar to the
post-Archean upper crustal rocks. The major and trace element
abundances of tektites analyzed indicate that the parental material of
tektites may be a terrestrial sedimentary deposit. The tektites from the
Wenchang area, Hainan Island have high positive εSr(0)
values-ranging from 184.5~196.5 which indicate that the parental
material for these tektites have similar Sr isotopic compositions to old
terrestrial sedimentary rocks and they were not dominantly derived
from recent young sediments (such as soil or loess). Based on Rb-Sr
isotopic data, it has been suggested by Blum (1992) [1]that the
depositional age of sedimentary target materials is close to 170Ma
(Jurassic). According to the model suggested by Ho and Chen
(1996)[2], mixing calculations for various amounts and combinations
of target rocks have been carried out. We consider that the best fit for
tektites from the Wenchang area is a mixture of 47% shale, 23%
sandstone, 25% greywacke and 5% quartzite, and the other tektites
from Khon Kaen area is a mixture of 46% shale, 2% sandstone, 20%
greywacke and 32% quartzite.
Abstract: This paper proposes a new design of spatial FIR
filter to automatically detect water level from a video signal of
various river surroundings. A new approach in this report applies
"addition" of frames and a "horizontal" edge detector to distinguish
water region and land region. Variance of each line of a filtered
video frame is used as a feature value. The water level is recognized
as a boundary line between the land region and the water region.
Edge detection filter essentially demarcates between two distinctly
different regions. However, the conventional filters are not
automatically adaptive to detect water level in various lighting
conditions of river scenery. An optimized filter is purposed so that
the system becomes robust to changes of lighting condition. More
reliability of the proposed system with the optimized filter is
confirmed by accuracy of water level detection.
Abstract: The launching nose plays an important role in the
incremental launching construction. The parameters of the launching
nose essentially affect the internal forces of the girder during the
construction. The appropriate parameters can decrease the internal
forces in the girder and save the material and reduce the cost. The
simplified structural model, which is made with displacement method
according to the characteristic of incremental launching construction
and the variation rule of the internal forces, calculates and analyzes the
effect of the length, the rigidity and weight of launch nose on the
internal forces of girder during the incremental launching
construction. The method, which can calculate the launching nose
parameters for the optimum incremental launching construction, is
achieved. This method is simple, reliable and easy for practical use.
Abstract: This paper deals with dynamic load balancing using PVM. In distributed environment Load Balancing and Heterogeneity are very critical issues and needed to drill down in order to achieve the optimal results and efficiency. Various techniques are being used in order to distribute the load dynamically among different nodes and to deal with heterogeneity. These techniques are using different approaches where Process Migration is basic concept with different optimal flavors. But Process Migration is not an easy job, it impose lot of burden and processing effort in order to track each process in nodes. We will propose a dynamic load balancing technique in which application will intelligently balance the load among different nodes, resulting in efficient use of system and have no overheads of process migration. It would also provide a simple solution to problem of load balancing in heterogeneous environment.
Abstract: Group contribution based models are widely used in
industrial applications for its convenience and flexibility. Although a
number of group contribution models have been proposed, there were
certain limitations inherent to those models. Models based on group
contribution excess Gibbs free energy are limited to low pressures and
models based on equation of state (EOS) cannot properly describe
highly nonideal mixtures including acids without introducing
additional modification such as chemical theory. In the present study
new a new approach derived from quantum chemistry have been used
to calculate necessary EOS group interaction parameters. The
COSMO-RS method, based on quantum mechanics, provides a
reliable tool for fluid phase thermodynamics. Benefits of the group
contribution EOS are the consistent extension to hydrogen-bonded
mixtures and the capability to predict polymer-solvent equilibria up to
high pressures. The authors are confident that with a sufficient
parameter matrix the performance of the lattice EOS can be improved
significantly.