Abstract: Carbon steel is used in boilers, pressure vessels, heat
exchangers, piping, structural elements and other moderatetemperature
service systems in which good strength and ductility are
desired. ASME Boiler and Pressure Vessel Code, Section II Part A
(2004) provides specifications of ferrous materials for construction of
pressure equipment, covering wide range of mechanical properties
including high strength materials for power plants application.
However, increased level of springback is one of the major problems
in fabricating components of high strength steel using bending.
Presented work discuss the springback simulations for five different
steels (i.e. SA-36, SA-299, SA-515 grade 70, SA-612 and SA-724
grade B) using finite element analysis of air V-bending. Analytical
springback simulations of hypothetical layered materials are
presented. Result shows that; (i) combination of the material property
parameters controls the springback, (ii) layer of the high ductility
steel on the high strength steel greatly suppresses the springback.
Abstract: Polymer-like organic thin films were deposited on both
aluminum alloy type 6061 and glass substrates at room temperature by
Plasma Enhanced Chemical Vapor Deposition (PECVD) methodusing
benzene and hexamethyldisiloxane (HMDSO) as precursor materials.
The surface and physical properties of plasma-polymerized organic
thin films were investigated at different r.f. powers. The effects of
benzene/argon ratio on the properties of plasma polymerized benzene
films were also investigated. It is found that using benzene alone
results in a non-coherent and non-adherent powdery deposited
material. The chemical structure and surface properties of the asgrown
plasma polymerized thin films were analyzed on glass
substrates with FTIR and contact angle measurements. FTIR spectra
of benzene deposited film indicated that the benzene rings are
preserved when increasing benzene ratio and/or decreasing r.f.
powers. FTIR spectra of HMDSO deposited films indicated an
increase of the hydrogen concentration and a decrease of the oxygen
concentration with the increase of r.f. power. The contact angle (θ) of
the films prepared from benzene was found to increase by about 43%
as benzene ratio increases from 10% to 20%. θ was then found to
decrease to the original value (51°) when the benzene ratio increases
to 100%. The contact angle, θ, for both benzene and HMDSO
deposited films were found to increase with r.f. power. This signifies
that the plasma polymerized organic films have substantially low
surface energy as the r.f power increases. The corrosion resistance of
aluminum alloy substrate both bare and covered with plasma
polymerized thin films was carried out by potentiodynamic
polarization measurements in standard 3.5 wt. % NaCl solution at
room temperature. The results indicate that the benzene and HMDSO
deposited films are suitable for protection of the aluminum substrate
against corrosion. The changes in the processing parameters seem to
have a strong influence on the film protective ability. Surface
roughness of films deposited on aluminum alloy substrate was
investigated using scanning electron microscopy (SEM). The SEM
images indicate that the surface roughness of benzene deposited films
increase with decreasing the benzene ratio. SEM images of benzene
and HMDSO deposited films indicate that the surface roughness
decreases with increasing r.f. power. Studying the above parameters
indicate that the films produced are suitable for specific practical
applications.
Abstract: In industry, on of the most important subjects is die
and it's characteristics in which for cutting and forming different
mechanical pieces, various punch and matrix metal die are used.
whereas the common parts which form the main frame die are not
often proportion with pieces and dies therefore using a part as socalled
common part for frames in specified dimension ranges can
decrease the time of designing, occupied space of warehouse and
manufacturing costs. Parts in dies with getting uniform in their shape
and dimension make common parts of dies. Common parts of punch
and matrix metal die are as bolster, guide bush, guide pillar and
shank. In this paper the common parts and effective parameters in
selecting each of them as the primary information are studied,
afterward for selection and design of mechanical parts an
introduction and investigation based on the Mech. Desk. software is
done hence with developing this software can standardize the metal
common parts of punch and matrix. These studies will be so useful
for designer in their designing and also using it has with very much
advantage for manufactures of products in decreasing occupied
spaces by dies.
Abstract: High level and high velocity flood flows are
potentially harmful to bridge piers as evidenced in many toppled
piers, and among them the single-column piers were considered as
the most vulnerable. The flood flow characteristic parameters
including drag coefficient, scouring and vortex shedding are built into
a pier-flood interaction model to investigate structural safety against
flood hazards considering the effects of local scouring, hydrodynamic
forces, and vortex induced resonance vibrations. By extracting the
pier-flood simulation results embedded in a neural networks code,
two cases of pier toppling occurred in typhoon days were reexamined:
(1) a bridge overcome by flash flood near a mountain side;
(2) a bridge washed off in flood across a wide channel near the
estuary. The modeling procedures and simulations are capable of
identifying the probable causes for the tumbled bridge piers during
heavy floods, which include the excessive pier bending moments and
resonance in structural vibrations.
Abstract: A theoretical approach to radiation damage evolution
is developed. Stable temporal behavior taking place in solids under
irradiation are examined as phenomena of self-organization in nonequilibrium
systems.
Experimental effects of temporal self-organization in solids under
irradiation are reviewed. Their essential common properties and
features are highlighted and analyzed.
Dynamical model to describe development of self-oscillation of
density of point defects under stationary irradiation is proposed. The
emphasis is the nonlinear couplings between rate of annealing and
density of defects that determine the kind and parameters of an
arising self-oscillation.
The field of parameters (defect generation rate and environment
temperature) at which self-oscillations develop is found. Bifurcation
curve and self-oscillation period near it is obtained.
Abstract: The paper presents the results of theoretical and
numerical modeling of propagation of shock waves in bubbly liquids
related to nonlinear effects (realistic equation of state, chemical
reactions, two-dimensional effects). On the basis on the Rankine-
Hugoniot equations the problem of determination of parameters of
passing and reflected shock waves in gas-liquid medium for
isothermal, adiabatic and shock compression of the gas component is
solved by using the wide-range equation of state of water in the
analitic form. The phenomenon of shock wave intensification is
investigated in the channel of variable cross section for the
propagation of a shock wave in the liquid filled with bubbles
containing chemically active gases. The results of modeling of the
wave impulse impact on the solid wall covered with bubble layer are
presented.
Abstract: In order to meet environmental norms, Indian fuel
policy aims at producing ultra low sulphur diesel (ULSD) in near
future. A catalyst for meeting such requirements has been developed
and kinetics of this catalytic process is being looked into. In the
present investigations, effect of mass transfer on kinetics of ultra deep
hydrodesulphurization (UDHDS) to produce ULSD has been studied
to determine intrinsic kinetics over a pre-sulphided catalyst.
Experiments have been carried out in a continuous flow micro reactor
operated in the temperature range of 330 to 3600C, whsv of 1 hr-1 at a
pressure of 35 bar, and its parameters estimated. Based on the derived
rate expression and estimated parameters optimum operation range
has been determined for this UDHDS catalyst to obtain ULSD
product.
Abstract: This paper presents a Neural Network (NN) identification of icing parameters in an A340 aircraft and a reconfiguration technique to keep the A/C performance close to the performance prior to icing. Five aircraft parameters are assumed to be considerably affected by icing. The off-line training for identifying the clear and iced dynamics is based on the Levenberg-Marquard Backpropagation algorithm. The icing parameters are located in the system matrix. The physical locations of the icing are assumed at the right and left wings. The reconfiguration is based on the technique known as the control mixer approach or pseudo inverse technique. This technique generates the new control input vector such that the A/C dynamics is not much affected by icing. In the simulations, the longitudinal and lateral dynamics of an Airbus A340 aircraft model are considered, and the stability derivatives affected by icing are identified. The simulation results show the successful NN identification of the icing parameters and the reconfigured flight dynamics having the similar performance before the icing. In other words, the destabilizing icing affect is compensated.
Abstract: A pot experiment was carried out under controlled
conditions to evaluate the residual effects of different doses of
atrazine+alachlor and foramsulfuron used in corn fields on the
growth and physiology of rapeseed (Brassica napus L.). A split-plot
experiment in CRD with 4 replications was used. The main plots
consisted of herbicide type (atrazine+alachlor mixture and
foramsulfuron) and the sub-plots were different residual doses of the
herbicides (0, 1%, 5%, 10%, 20%, 40%, 50% and 100%). 7 cm
diameter pots were filled with a virgin soil and seeds of rapeseed cv.
Hayola were planted in them. The pots were kept under controlled
conditions for 8 weeks after germination. At harvest, the growth
parameters and the chlorophyll contents of the leaves were
determined. The results showed that the growth of rapeseed plants
was completely prevented at the highest residual doses of the
herbicides (50 and 100 %). The growth parameters of rapeseed plants
were affected by all doses of both types of the herbicide as compared
to the controls. The residual effects of atrazine+alachlor mixture in
reducing the growth parameters of rapeseed were more pronounced
as compared to the residual effects of foramsulfuron alone.
Abstract: The paper presents an optimization study based on
genetic algorithms (GA-s) for a radio-frequency applicator used in
heating dielectric band products. The weakly coupled electro-thermal
problem is analyzed using 2D-FEM. The design variables in the
optimization process are: the voltage of a supplementary “guard"
electrode and six geometric parameters of the applicator. Two
objective functions are used: temperature uniformity and total active
power absorbed by the dielectric. Both mono-objective and multiobjective
formulations are implemented in GA optimization.
Abstract: Partial Discharge measurement is a very important
means of assessing the integrity of insulation systems in a High
Voltage apparatus. In compressed gas insulation systems, floating
particles can initiate partial discharge activities which adversely
affect the working of insulation. Partial Discharges below the
inception voltage also plays a crucial in damaging the integrity of
insulation over a period of time. This paper discusses the effect of
loose and fixed Copper and Nichrome wire particles on the PD
characteristics in SF6-N2 (10:90) gas mixtures at a pressure of
0.4MPa. The Partial Discharge statistical parameters and their
correlation to the observed results are discussed.
Abstract: The objective this study was to characterize and
develop anthropomorphic liver phantoms in tomography hepatic
procedures for quality control and improvement professionals in
nuclear medicine. For the conformation of the anthropomorphic
phantom was used in plaster and acrylic. We constructed three
phantoms representing processes with liver cirrhosis. The phantoms
were filled with 99mTc diluted with water to obtain the scintigraphic
images. Tomography images were analyzed anterior and posterior
phantom representing a body with a greater degree cirrhotic. It was
noted that the phantoms allow the acquisition of images similar to
real liver with cirrhosis. Simulations of hemangiomas may contribute
to continued professional education of nuclear medicine, on the
question of image acquisition, allowing of the study parameters such
of the matrix, energy window and count statistics.
Abstract: In the present paper, the three-dimensional
temperature field of tool is determined during the machining and
compared with experimental work on C45 workpiece using carbide
cutting tool inserts. During the metal cutting operations, high
temperature is generated in the tool cutting edge which influence on
the rate of tool wear. Temperature is most important characteristic of
machining processes; since many parameters such as cutting speed,
surface quality and cutting forces depend on the temperature and high
temperatures can cause high mechanical stresses which lead to early
tool wear and reduce tool life. Therefore, considerable attention is
paid to determine tool temperatures. The experiments are carried out
for dry and orthogonal machining condition. The results show that
the increase of tool temperature depends on depth of cut and
especially cutting speed in high range of cutting conditions.
Abstract: Physiological activity of the pineal gland with specific
responses in the reproductive territory may be interpreted by
monitoring the process parameters used in poultry practice in
different age batches of laying hens. As biological material were
used 105 laying hens, clinically healthy, belonging to ALBO SL-
2000 hybrid, raised on ground, from which blood samples were taken
at the age of 12 and 28 weeks. The haematological examinations
were concerned to obtain the total number of erythrocytes and
leukocytes and the main erythrocyte constant (RBC, PCV, MCV,
MCH, MCHC and WBC). The results allow the interpretation of the
reproductive status through the dynamics of the presented values.
Abstract: In this paper, we investigated vector control of an induction machine taking into account discretization problems of the command. In the purpose to show how to include in a discrete model of this current control and with rotor time constant update. The results of simulation obtained are very satisfaisant. That was possible thanks to the good choice of the values of the parameters of the regulators used which shows, the founded good of the method used, for the choice of the parameters of the discrete regulators. The simulation results are presented at the end of this paper.
Abstract: This article proposes modeling, simulation and
kinematic and workspace analysis of a spatial cable suspended robot
as incompletely Restrained Positioning Mechanism (IRPM). These
types of robots have six cables equal to the number of degrees of
freedom. After modeling, the kinds of workspace are defined then an
statically reachable combined workspace for different geometric
structures of fixed and moving platform is obtained. This workspace
is defined as the situations of reference point of the moving platform
(center of mass) which under external forces such as weight and with
ignorance of inertial effects, the moving platform should be in static
equilibrium under conditions that length of all cables must not be
exceeded from the maximum value and all of cables must be at
tension (they must have non-negative tension forces). Then the effect
of various parameters such as the size of moving platform, the size of
fixed platform, geometric configuration of robots, magnitude of
applied forces and moments to moving platform on workspace of
these robots with different geometric configuration are investigated.
Obtained results should be effective in employing these robots under
different conditions of applied wrench for increasing the workspace
volume.
Abstract: The paper discusses the results obtained to predict
reinforcement in singly reinforced beam using Neural Net (NN),
Support Vector Machines (SVM-s) and Tree Based Models. Major
advantage of SVM-s over NN is of minimizing a bound on the
generalization error of model rather than minimizing a bound on
mean square error over the data set as done in NN. Tree Based
approach divides the problem into a small number of sub problems to
reach at a conclusion. Number of data was created for different
parameters of beam to calculate the reinforcement using limit state
method for creation of models and validation. The results from this
study suggest a remarkably good performance of tree based and
SVM-s models. Further, this study found that these two techniques
work well and even better than Neural Network methods. A
comparison of predicted values with actual values suggests a very
good correlation coefficient with all four techniques.
Abstract: In this paper, a new approach is introduced to solve
Blasius equation using parameter identification of a nonlinear
function which is used as approximation function. Bees Algorithm
(BA) is applied in order to find the adjustable parameters of
approximation function regarding minimizing a fitness function
including these parameters (i.e. adjustable parameters). These
parameters are determined how the approximation function has to
satisfy the boundary conditions. In order to demonstrate the
presented method, the obtained results are compared with another
numerical method. Present method can be easily extended to solve a
wide range of problems.
Abstract: this study was carried out to investigate the changes in
quality parameters of rye bread packaged in different polymer films
during convection air-flow thermal treatment process. Whole loafs of
bread were placed in polymer pouches, which were sealed in reduced
pressure air ambiance, bread was thermally treated in
at temperature +(130; 140; and 150) ± 5 ºC within 40min, as long as
the core temperature of the samples have reached accordingly
+80±1 ºC. For bread packaging pouches were used: anti-fog
Mylar®OL12AF and thermo resistant combined polymer material.
Main quality parameters was analysed using standard methods:
temperature in bread core, bread crumb and crust firmness value,
starch granules volume and microflora. In the current research it was
proved, that polymer films significantly influence rye bread quality
parameters changes during thermal treatment. Thermo resistant
combined polymer material film could be recommendable for
packaged rye bread pasteurization, for maximal bread quality
parameter keeping.
Abstract: This research focuses on the effect of weight
percentage variation and size variation of MgFeSi added,
gating system design and reaction chamber design on inmold
process. By using inmold process, well-known problem of
fading is avoided because the liquid iron reacts with
magnesium in the mold and not, as usual, in the ladle. During
the pouring operation, liquid metal passes through the
chamber containing the magnesium, where the reaction of the
metal with magnesium proceeds in the absence of atmospheric
oxygen [1].In this paper, the results of microstructural
characteristic of ductile iron on this parameters are mentioned.
The mechanisms of the inmold process are also described [2].
The data obtained from this research will assist in producing
the vehicle parts and other machinery parts for different
industrial zones and government industries and in transferring
the technology to all industrial zones in Myanmar. Therefore,
the inmold technology offers many advantages over traditional
treatment methods both from a technical and environmental,
as well as an economical point of view. The main objective of
this research is to produce ductile iron castings in all industrial
sectors in Myanmar more easily with lower costs. It will also
assist the sharing of knowledge and experience related to the
ductile iron production.