Abstract: The present energy situation and the concerns
about global warming has stimulated active research interest
in non-petroleum, carbon free compounds and non-polluting
fuels, particularly for transportation, power generation, and
agricultural sectors. Environmental concerns and limited
amount of petroleum fuels have caused interests in the
development of alternative fuels for internal combustion (IC)
engines. The petroleum crude reserves however, are declining
and consumption of transport fuels particularly in the
developing countries is increasing at high rates. Severe
shortage of liquid fuels derived from petroleum may be faced
in the second half of this century. Recently more and more
stringent environmental regulations being enacted in the USA
and Europe have led to the research and development
activities on clean alternative fuels. Among the gaseous fuels
hydrogen is considered to be one of the clean alternative fuel.
Hydrogen is an interesting candidate for future internal
combustion engine based power trains. In this experimental
investigation, the performance and combustion analysis were
carried out on a direct injection (DI) diesel engine using
hydrogen with diesel following the TMI(Time Manifold
Injection) technique at different injection timings of 10
degree,45 degree and 80 degree ATDC using an electronic
control unit (ECU) and injection durations were controlled.
Further, the tests have been carried out at a constant speed of
1500rpm at different load conditions and it can be observed
that brake thermal efficiency increases with increase in load
conditions with a maximum gain of 15% at full load
conditions during all injection strategies of hydrogen. It was
also observed that with the increase in hydrogen energy share
BSEC started reducing and it reduced to a maximum of 9% as
compared to baseline diesel at 10deg ATDC injection during
maximum injection proving the exceptional combustion
properties of hydrogen.
Abstract: To understand the material characteristics of singleand
poly-crystals of pure copper, the respective relationships between
crystallographic orientations and microstructures, and the bending
and mechanical properties were examined. And texture distribution
is also analyzed. A bending test is performed in a SEM apparatus and
while its behaviors are observed in situ. Furthermore, some
analytical results related to crystal direction maps, inverse pole
figures, and textures were obtained from EBSD analyses.
Abstract: The new status generated by technological advancements and changes in the global economy raises important issues on how communities and organisations need to innovate upon their traditional processes in order to adapt to the challenges of the Knowledge Society. The DialogoS+ European project aims to study the role of and promote social dialogue in the banking sector, strengthen the link between old and new members and make social dialogue at the European level a force for innovation and change, also given the context of the international crisis emerging in 2008- 2009. Under the scope of DialogoS+, this paper describes how the community of Europe-s banking sector trade unions attempted to adapt to the challenges of the Knowledge Society by exploiting the benefits of new channels of communication, learning, knowledge generation and diffusion focusing on the concept of roadmapping. Important dimensions of social dialogue such as collective bargaining and working conditions are addressed.
Abstract: Graduate attributes have received increasing attention
over recent years as universities incorporate these attributes into the
curriculum. Graduates who have adequate technical knowledge only
are not sufficiently equipped to compete effectively in the work
place; they also need non disciplinary skills ie, graduate attributes.
The purpose of this paper is to investigate the impact of an eportfolio
in a technical communication course to enhance engineering
students- graduate attributes: namely, learning of communication,
critical thinking and problem solving and teamwork skills. Two
questionnaires were used to elicit information from the students: one
on their preferred and the other on the actual learning process. In
addition, student perceptions of the use of eportfolio as a learning
tool were investigated. Preliminary findings showed that most of the
students- expectations have been met with their actual learning. This
indicated that eportfolio has the potential as a tool to enhance
students- graduate attributes.
Abstract: To solve the quick and accurate level-adjusting
problem in the process of spacecraft precise mating, automatic leveling
and equalizing hoist device for spacecraft is developed. Based on
lifting point adjustment by utilizing XY-workbench, the leveling and
equalizing controller by a self-adaptive control algorithm is proposed.
By simulation analysis and lifting test using engineering prototype,
validity and reliability of the hoist device is verified, which can meet
the precision mating requirements of practical applications for
spacecraft.
Abstract: The distressing flood scenarios that occur in
recent years at the surrounding areas of Sarawak River have
left damages of properties and indirectly caused disruptions of
productive activities. This study is meant to reconstruct a 100-year
flood event that took place in this river basin. Sarawak River Subbasin
was chosen and modeled using the one-dimensional
hydrodynamic modeling approach using InfoWorks River Simulation
(RS), in combination with Geographical Information System (GIS).
This produces the hydraulic response of the river and its floodplains
in extreme flooding conditions. With different parameters introduced
to the model, correlations of observed and simulated data are
between 79% – 87%. Using the best calibrated model, flood
mitigation structures are imposed along the sub-basin. Analysis is
done based on the model simulation results. Result shows that the
proposed retention ponds constructed along the sub-basin provide the
most efficient reduction of flood by 34.18%.
Abstract: The purpose of this research is to establish the experimental conditions for removal of Cibacron Brilliant Yellow 3G-P dye (CBY) from aqueous solutions by sorption onto coffee husks as a low-cost sorbent. The effects of various experimental parameters (e.g. initial CBY dye concentration, sorbent mass, pH, temperature) were examined and the optimal experimental conditions were determined. The results indicated that the removal of the dye was pH dependent and at initial pH of 2, the dye was removed effectively. The CBY dye sorption data were fitted to Langmuir, Freundlich, Temkin and Dubinin-Radushkevich equilibrium models. The maximum sorption capacity of CBY dye ions onto coffee husks increased from 24.04 to 35.04 mg g-1 when the temperature was increased from 293 to 313 K. The calculated sorption thermodynamic parameters including ΔG°, ΔH°, and ΔS° indicated that the CBY dye sorption onto coffee husks is a spontaneous, endothermic and mainly physical in nature.
Abstract: Many experimental results suggest that more precise spike timing is significant in neural information processing. We construct a self-organization model using the spatiotemporal pat-terns, where Spike-Timing Dependent Plasticity (STDP) tunes the conduction delays between neurons. We show that, for highly syn-chronized inputs, the fluctuation of conduction delays causes globally continuous and locally distributed firing patterns through the self-organization.
Abstract: The necessity of solving multi dimensional
complicated scientific problems beside the necessity of several
objective functions optimization are the most motive reason of born
of artificial intelligence and heuristic methods.
In this paper, we introduce a new method for multiobjective
optimization based on learning automata. In the proposed method,
search space divides into separate hyper-cubes and each cube is
considered as an action. After gathering of all objective functions
with separate weights, the cumulative function is considered as the
fitness function. By the application of all the cubes to the cumulative
function, we calculate the amount of amplification of each action and
the algorithm continues its way to find the best solutions. In this
Method, a lateral memory is used to gather the significant points of
each iteration of the algorithm. Finally, by considering the
domination factor, pareto front is estimated. Results of several
experiments show the effectiveness of this method in comparison
with genetic algorithm based method.
Abstract: In this paper, we argue the security protocols of
ZigBee wireless sensor network in MAC layer. AES 128-bit
encryption algorithm in CCM* mode is secure transferred data;
however, AES-s secret key will be break within nearest future.
Efficient public key algorithm, ECC has been mixed with AES to
rescue the ZigBee wireless sensor from cipher text and replay attack.
Also, the proposed protocol can parallelize the integrity function to
increase system performance.
Abstract: Regenerative Thermal Oxidizer (RTO) is one of the
best solutions for removal of Volatile Organic Compounds (VOC)
from industrial processes. In the RTO, VOC in a raw gas are usually
decomposed at 950-1300 K and the combustion heat of VOC is
recovered by regenerative heat exchangers charged with ceramic
honeycombs. The optimization of the treatment of VOC leads to the
reduction of fuel addition to VOC decomposition, the minimization of
CO2 emission and operating cost as well.
In the present work, the thermal efficiency of the RTO was
investigated experimentally in a pilot-scale RTO unit using toluene as
a typical representative of VOC. As a result, it was recognized that the
radiative heat transfer was dominant in the preheating process of a raw
gas when the gas flow rate was relatively low. Further, it was found
that a minimum heat exchanger volume to achieve self combustion of
toluene without additional heating of the RTO by fuel combustion was
dependent on both the flow rate of a raw gas and the concentration of
toluene. The thermal efficiency calculated from fuel consumption and
the decomposed toluene ratio, was found to have a maximum value of
0.95 at a raw gas mass flow rate of 1810 kg·h-1 and honeycombs height
of 1.5m.
Abstract: In the present paper, we use generalized B-Spline curve in trigonometric form on circular domain, to capture the transcendental nature of circle involute curve and uncertainty characteristic of design. The required involute curve get generated within the given tolerance limit and is useful in gear design.
Abstract: Carboneous catalytical methane decomposition is an
attractive process because it produces two valuable products:
hydrogen and carbon. Furthermore, this reaction does not emit any
green house or hazardous gases. In the present study, experiments
were conducted in a thermo gravimetric analyzer using Fluka 05120
as carboneous catalyst to analyze its effectiveness in methane
decomposition. Various temperatures and methane partial pressures
were chosen and carbon mass gain was observed as a function of
time. Results are presented in terms of carbon formation rate,
hydrogen production and catalytical activity. It is observed that there
is linearity in carbon deposition amount by time at lower reaction
temperature (780 °C). On the other hand, it is observed that carbon
and hydrogen formation rates are increased with increasing
temperature. Finally, we observed that the carbon formation rate is
highest at 950 °C within the range of temperatures studied.
Abstract: This paper is a continuation of our interest in the influence of temperature on specific retention volumes and the resulting infinite dilution activity coefficients. This has a direct effect in the design of absorption and stripping columns for the abatement of volatile organic compounds. The interaction of 13 volatile organic compounds (VOCs) with polydimethylsiloxane (PDMS) at varying temperatures was studied by gas liquid chromatography (GLC). Infinite dilution activity coefficients and specific retention volumes obtained in this study were found to be in agreement with those obtained from static headspace and group contribution methods by the authors as well as literature values for similar systems. Temperature variation also allows for transport calculations for different seasons. The results of this work confirm that PDMS is well suited for the scrubbing of VOCs from waste gas streams. Plots of specific retention volumes against temperature gave linear van-t Hoff plots.
Abstract: Mobile devices, which are progressively surrounded
in our everyday life, have created a new paradigm where they
interconnect, interact and collaborate with each other. This network
can be used for flexible and secure coordinated sharing. On the other
hand Grid computing provides dependable, consistent, pervasive, and
inexpensive access to high-end computational capabilities. In this
paper, efforts are made to map the concepts of Grid on Ad-Hoc
networks because both exhibit similar kind of characteristics like
Scalability, Dynamism and Heterogeneity. In this context we
propose “Mobile Ad-Hoc Services Grid – MASGRID".
Abstract: Extracting and elaborating software requirements and
transforming them into viable software architecture are still an
intricate task. This paper defines a solution architecture which is
based on the blurred amalgamation of problem space and solution
space. The dependencies between domain constraints, requirements
and architecture and their importance are described that are to be
considered collectively while evolving from problem space to
solution space. This paper proposes a revised version of Twin Peaks
Model named Win Peaks Model that reconciles software
requirements and architecture in more consistent and adaptable
manner. Further the conflict between stakeholders- win-requirements
is resolved by proposed Voting methodology that is simple
adaptation of win-win requirements negotiation model and QARCC.
Abstract: In this paper, we propose a direct method based on the
real Schur factorization for solving the projected Sylvester equation
with relatively small size. The algebraic formula of the solution of
the projected continuous-time Sylvester equation is presented. The
computational cost of the direct method is estimated. Numerical
experiments show that this direct method has high accuracy.
Abstract: Vehicle which are turning or maneuvering at high speeds
are susceptible to sliding and subsequently deviate from desired path. In
this paper the dynamics governing the Yaw/Roll behavior of a vehicle
has been simulated. Two different simulations have been used one for
the real vehicle, for which a fuzzy controller is designed to increase its
directional stability property. The other simulation is for a hypothetical
vehicle with much higher tire cornering stiffness which is capable of
developing the required lateral forces at the tire-ground patch contact to
attain the desired lateral acceleration for the vehicle to follow the
desired path without slippage. This simulation model is our reference
model.
The logic for keeping the vehicle on the desired track in the cornering
or maneuvering state is to have some braking forces on the inner or
outer tires based on the direction of vehicle deviation from the desired
path. The inputs to our vehicle simulation model is steer angle δ and
vehicle velocity V , and the outputs can be any kinematical parameters
like yaw rate, yaw acceleration, side slip angle, rate of side slip angle
and so on. The proposed fuzzy controller is a feed forward controller.
This controller has two inputs which are steer angle δ and vehicle
velocity V, and the output of the controller is the correcting moment M,
which guides the vehicle back to the desired track. To develop the
membership functions for the controller inputs and output and the fuzzy
rules, the vehicle simulation has been run for 1000 times and the
correcting moment have been determined by trial and error. Results of
the vehicle simulation with fuzzy controller are very promising
and show the vehicle performance is enhanced greatly over the
vehicle without the controller. In fact the vehicle performance
with the controller is very near the performance of the reference
ideal model.
Abstract: In areas of low to moderate seismicity many building contents and equipment are not positively fixed to the floor or tied to adjacent walls. Under seismic induced horizontal vibration, such contents and equipment can suffer from damage by either overturning or impact associated with rocking. This paper focuses on the estimation of shock on typical contents and equipment due to rocking. A simplified analytical model is outlined that can be used to estimate the maximum acceleration on a rocking object given its basic geometric and mechanical properties. The developed model was validated against experimental results. The experimental results revealed that the maximum shock acceleration can be underestimated if the static stiffness of the materials at the interface between the rocking object and floor is used rather than the dynamic stiffness. Excellent agreement between the model and experimental results was found when the dynamic stiffness for the interface material was used, which was found to be generally much higher than corresponding static stiffness under different investigated boundary conditions of the cushion. The proposed model can be a beneficial tool in performing a rapid assessment of shock sensitive components considered for possible seismic rectification.
Abstract: Dengue virus is transmitted from person to person
through the biting of infected Aedes Aegypti mosquitoes. DEN-1,
DEN-2, DEN-3 and DEN-4 are four serotypes of this virus. Infection
with one of these four serotypes apparently produces permanent
immunity to it, but only temporary cross immunity to the others. The
length of time during incubation of dengue virus in human and
mosquito are considered in this study. The dengue patients are
classified into infected and infectious classes. The infectious human
can transmit dengue virus to susceptible mosquitoes but infected
human can not. The transmission model of this disease is formulated.
The human population is divided into susceptible, infected, infectious
and recovered classes. The mosquito population is separated into
susceptible, infected and infectious classes. Only infectious
mosquitoes can transmit dengue virus to the susceptible human. We
analyze this model by using dynamical analysis method. The
threshold condition is discussed to reduce the outbreak of this
disease.