Abstract: Cooktop burners are widely used nowadays. In
cooktop burner design, nozzle efficiency and greenhouse
gas(GHG) emissions mainly depend on heat transfer from the
premixed flame to the impinging surface. This is a complicated
issue depending on the individual and combined effects of various
input combustion variables. Optimal operating conditions for
sustainable burner design were rarely addressed, especially in the
case of multiple slot-jet burners. Through evaluating the optimal
combination of combustion conditions for a premixed slot-jet
array, this paper develops a practical approach for the sustainable
design of gas cooktop burners. Efficiency, CO and NOx emissions
in respect of an array of slot jets using premixed flames were
analysed. Response surface experimental design were applied to
three controllable factors of the combustion process, viz.
Reynolds number, equivalence ratio and jet-to-vessel distance.
Desirability Function Approach(DFA) is the analytic technique
used for the simultaneous optimization of the efficiency and
emission responses.
Abstract: The present work is concerned with the effect of turning process parameters (cutting speed, feed rate, and depth of cut) and distance from the center of work piece as input variables on the chip micro-hardness as response or output. Three experiments were conducted; they were used to investigate the chip micro-hardness behavior at diameter of work piece for 30[mm], 40[mm], and 50[mm]. Response surface methodology (R.S.M) is used to determine and present the cause and effect of the relationship between true mean response and input control variables influencing the response as a two or three dimensional hyper surface. R.S.M has been used for designing a three factor with five level central composite rotatable factors design in order to construct statistical models capable of accurate prediction of responses. The results obtained showed that the application of R.S.M can predict the effect of machining parameters on chip micro-hardness. The five level factorial designs can be employed easily for developing statistical models to predict chip micro-hardness by controllable machining parameters. Results obtained showed that the combined effect of cutting speed at it?s lower level, feed rate and depth of cut at their higher values, and larger work piece diameter can result increasing chi micro-hardness.
Abstract: This paper considers the problem of Null-Steering beamforming using Neural Network (NN) approach for antenna array system. Two cases are presented. First, unlike the other authors, the estimated Direction Of Arrivals (DOAs) are used for antenna array weights NN-based determination and the imprecise DOAs estimations are taken into account. Second, the blind null-steering beamforming is presented. In this case the antenna array outputs are presented at the input of the NN without DOAs estimation. The results of computer simulations will show much better relative mean error performances of the first NN approach compared to the NNbased blind beamforming.
Abstract: In this study the behavior of interlaminar fracture of
carbon-epoxy thermoplastic laminated composite is investigated
numerically and experimentally. Tests are performed with Arcan
specimens. Testing with Arcan specimen gives the opportunity of
utilizing just one kind of specimen for extracting fracture properties
for mode I, mode II and different mixed mode ratios of materials with
exerting load via different loading angles. Variation of loading angles
in range of 0-90° made possible to achieve different mixed mode
ratios. Correction factors for various conditions are obtained from
ABAQUS 2D finite element models which demonstrate the finite
shape of Arcan specimens used in this study. Finally, applying the
correction factors to critical loads obtained experimentally, critical
interlaminar fracture toughness of this type of carbon- epoxy
composite has been attained.
Abstract: Many IT projects come to failure because of having
technical approach, focusing on the final product and lack of proper
attention to strategic alignment. Project management models quite
often have technical management view [4], [8], [13], [14]. These
models focus greatly on the finalization of the project product and the
delivery of the product to the customer. However, many project
problems are due to lack of attention to the needs and capabilities of
the organizations or disregarding how to deploy and use the product
in the organization. In this regard, in the current research we are
trying to present a solution with the purpose of raising the value of
the project in an organization. This way, the project outputs will be
properly deployed in the organization. Therefore, a comprehensive
model is presented which takes into account the whole processes
from initial step of project definition to the deployment of the final
outputs in the organization and then the definition of all roles and
responsibilities to put the model into practice. Taking into account
the opinions of experts and project managers, to prove the
performance of the model, the project problems were recognized and
based on the model, categorized and analyzed. And at the end it is
made clear that ignoring the proper definition of the project and not
having a proper understanding of the expected value on the one hand
and not supervising the emerged value in the process of production
and installment are among the most important factors that bring a
project to failure.
Abstract: The multiple traveling salesman problem (mTSP) can be used to model many practical problems. The mTSP is more complicated than the traveling salesman problem (TSP) because it requires determining which cities to assign to each salesman, as well as the optimal ordering of the cities within each salesman's tour. Previous studies proposed that Genetic Algorithm (GA), Integer Programming (IP) and several neural network (NN) approaches could be used to solve mTSP. This paper compared the results for mTSP, solved with Genetic Algorithm (GA) and Nearest Neighbor Algorithm (NNA). The number of cities is clustered into a few groups using k-means clustering technique. The number of groups depends on the number of salesman. Then, each group is solved with NNA and GA as an independent TSP. It is found that k-means clustering and NNA are superior to GA in terms of performance (evaluated by fitness function) and computing time.
Abstract: Chemical detection is still a continuous challenge when
it comes to designing single-walled carbon nanotube (SWCNT)
sensors with high selectivity, especially in complex chemical
environments. A perfect example of such an environment would be in
thermally oxidized soybean oil. At elevated temperatures, oil oxidizes
through a series of chemical reactions which results in the formation of
monoacylglycerols, diacylglycerols, oxidized triacylglycerols, dimers,
trimers, polymers, free fatty acids, ketones, aldehydes, alcohols,
esters, and other minor products. In order to detect the rancidity of
oxidized soybean oil, carbon nanotube chemiresistor sensors have
been coated with polyethylenimine (PEI) to enhance the sensitivity
and selectivity. PEI functionalized SWCNTs are known to have a high
selectivity towards strong electron withdrawing molecules. The
sensors were very responsive to different oil oxidation levels and
furthermore, displayed a rapid recovery in ambient air without the
need of heating or UV exposure.
Abstract: Due to the emergence of “Humanized Healthcare"
introduced by Professor Dr. Prawase Wasi in 2003[1], the
development of this paradigm tends to be widely implemented. The
organizations included Healthcare Accreditation Institute (public
organization), National Health Foundation, Mahidol University in
cooperation with Thai Health Promotion Foundation, and National
Health Security Office (Thailand) have selected the hospitals or
infirmaries that are qualified for humanized healthcare since 2008-
2010 and 35 of them are chosen to be the outstandingly navigating
organizations for the development of humanized healthcare,
humanized healthcare award [2].
The research aims to study the current issue, characteristics and
patterns of hospital administration contributing to humanized
healthcare system in Thailand. The selected case studies are from
four hospitals including Dansai Crown Prince Hospital, Leoi;
Ubolrattana Hospital, Khon Kaen; Kapho Hospital, Pattani; and
Prathai Hospital, Nakhonrachasima. The methodology is in-depth
interviewing with 10 staffs working as hospital executive directors,
and representatives from leader groups including directors,
multidisciplinary hospital committees, personnel development
committees, physicians and nurses in each hospital. (Total=40) In
addition, focus group discussions between hospital staffs and general
people (including patients and their relatives, the community leader,
and other people) are held by means of setting 4 groups including 8
people within each group. (Total=128) The observation on the
working in each hospital is also implemented. The findings of the
study reveal that there are five important aspects found in each
hospital including (1) the quality improvement under the mental and
spiritual development policy from the chief executives and lead
teams, leaders as Role model and they have visionary leadership; (2)
the participation hospital administration system focusing on learning
process and stakeholder- needs, spiritual human resource
management and development; (3) the relationship among people
especially staffs, team work skills, mutual understanding, effective
communication and personal inner-development; (4) organization
culture relevant to the awareness of patients- rights as well as the
participation policy including spiritual growth achieving to the same
goals, sharing vision, developing public mind, and caring; and (5)
healing structures or environment providing warmth and convenience
for hospital staffs, patients and their relatives and visitors.
Abstract: This paper presents an optimization technique to economic load dispatch (ELD) problems with considering the daily load patterns and generator constraints using a particle swarm optimization (PSO). The objective is to minimize the fuel cost. The optimization problem is subject to system constraints consisting of power balance and generation output of each units. The application of a constriction factor into PSO is a useful strategy to ensure convergence of the particle swarm algorithm. The proposed method is able to determine, the output power generation for all of the power generation units, so that the total constraint cost function is minimized. The performance of the developed methodology is demonstrated by case studies in test system of fifteen-generation units. The results show that the proposed algorithm scan give the minimum total cost of generation while satisfying all the constraints and benefiting greatly from saving in power loss reduction
Abstract: This paper proposed a nonlinear model predictive
control (MPC) method for the control of gantry crane. One of the main
motivations to apply MPC to control gantry crane is based on its
ability to handle control constraints for multivariable systems. A
pre-compensator is constructed to compensate the input nonlinearity
(nonsymmetric dead zone with saturation) by using its inverse
function. By well tuning the weighting function matrices, the control
system can properly compromise the control between crane position
and swing angle. The proposed control algorithm was implemented for
the control of gantry crane system in System Control Lab of University
of Technology, Sydney (UTS), and achieved desired experimental
results.
Abstract: The increase in energy demand has raised concerns
over adverse impacts on the environment from energy generation. It
is important to understand the status of energy consumption for
institutions such as Curtin Sarawak to ensure the sustainability of
energy usage, and also to reduce its costs. In this study, a preliminary
audit framework was developed and was conducted around the
Malaysian campus to obtain information such as the number and
specifications of electrical appliances, built-up area and ambient
temperature to understand the relationship of these factors with
energy consumption. It was found that the number and types of
electrical appliances, population and activities in the campus
impacted the energy consumption of Curtin Sarawak directly.
However, the built-up area and ambient temperature showed no clear
correlation with energy consumption. An investigation of the diurnal
and seasonal energy consumption of the campus was also carried out.
From the data, recommendations were made to improve the energy
efficiency of the campus.
Abstract: Serious games have proven to be a useful instrument
to engage learners and increase motivation. Nevertheless, a broadly
accepted, practical instructional design approach to serious games
does not exist. In this paper, we introduce the use of an instructional
design model that has not been applied to serious games yet, and has
some advantages compared to other design approaches. We present
the case of mechanics mechatronics education to illustrate the close
match with timing and role of knowledge and information that the
instructional design model prescribes and how this has been
translated to a rigidly structured game design. The structured
approach answers the learning needs of applicable knowledge within
the target group. It combines advantages of simulations with
strengths of entertainment games to foster learner-s motivation in the
best possible way. A prototype of the game will be evaluated along a
well-respected evaluation method within an advanced test setting
including test and control group.
Abstract: In this study, an OCR system for segmentation,
feature extraction and recognition of Ottoman Scripts has been
developed using handwritten characters. Detection of handwritten
characters written by humans is a difficult process. Segmentation and
feature extraction stages are based on geometrical feature analysis,
followed by the chain code transformation of the main strokes of
each character. The output of segmentation is well-defined segments
that can be fed into any classification approach. The classes of main
strokes are identified through left-right Hidden Markov Model
(HMM).
Abstract: Science and technology of ultrasonic is widely used in
recent years for industrial and medicinal application. The acoustical
properties of 2-mercapto substituted pyrimidines viz.,2- Mercapto-4-
(2’,4’ –dichloro phenyl) – 6-(2’ – hydroxyl -4’ –methyl-5’ –
chlorophenyl) pyrimidine and 2 –Mercapto – 4-(4’ –chloro phenyl) –
6-(2’ – hydroxyl -4’ –methyl-5’ –chlorophenyl) pyrimidine have been
investigated from the ultrasonic velocity and density measurements at
different concentration and different % in dioxane-water mixture at
305K. The adiabatic compressibility (βs), acoustic impedance (Z),
intermolecular free length (Lf), apparent molar volume(ϕv) and
relative association (RA) values have been calculated from the
experimental data of velocity and density measurement at
concentration range of 0.01- 0.000625 mol/lit and 70%,75% and 80%
dioxane water mixture. These above parameters are used to discuss
the structural and molecular interactions.
Abstract: This paper investigates the effectiveness of the use of
seismic isolation devices on the overall 3D seismic response of
curved highway viaducts with an emphasis on expansion joints.
Furthermore, an evaluation of the effectiveness of the use of cable
restrainers is presented. For this purpose, the bridge seismic
performance has been evaluated on four different radii of curvature,
considering two cases: restrained and unrestrained curved viaducts.
Depending on the radius of curvature, three-dimensional non-linear
dynamic analysis shows the vulnerability of curved viaducts to
pounding and deck unseating damage. In this study, the efficiency of
using LRB supports combined with cable restrainers on curved
viaducts is demonstrated, not only by reducing in all cases the
possible damage, but also by providing a similar behavior in the
viaducts despite of curvature radius.
Abstract: Bioprocesses are appreciated as difficult to control because their dynamic behavior is highly nonlinear and time varying, in particular, when they are operating in fed batch mode. The research objective of this study was to develop an appropriate control method for a complex bioprocess and to implement it on a laboratory plant. Hence, an intelligent control structure has been designed in order to produce biomass and to maximize the specific growth rate.
Abstract: Traditional multivariate control charts assume that measurement from manufacturing processes follows a multivariate normal distribution. However, this assumption may not hold or may be difficult to verify because not all the measurement from manufacturing processes are normal distributed in practice. This study develops a new multivariate control chart for monitoring the processes with non-normal data. We propose a mechanism based on integrating the one-class classification method and the adaptive technique. The adaptive technique is used to improve the sensitivity to small shift on one-class classification in statistical process control. In addition, this design provides an easy way to allocate the value of type I error so it is easier to be implemented. Finally, the simulation study and the real data from industry are used to demonstrate the effectiveness of the propose control charts.
Abstract: The simple methods used to plan and measure non
patterned production system are developed from the basic definition
of working efficiency. Processing time is assigned as the variable
and used to write the equation of production efficiency.
Consequently, such equation is extensively used to develop the
planning method for production of interest using one-dimensional
stock cutting problem. The application of the developed method
shows that production efficiency and production planning can be
determined effectively.
Abstract: The study and development of an innovative material
for building insulation is really important for a sustainable society in order to improve comfort and reducing energy consumption. The aim of this work is the development of insulating panels for
sustainable buildings based on an innovative material made by
cardboard and Phase Change Materials (PCMs).
The research has consisted in laboratory tests whose purpose has been the obtaining of the required properties for insulation panels: lightweight, porous structures and mechanical resistance. PCMs have been used for many years in the building industry as
smart insulation technology because of their properties of storage and release high quantity of latent heat at useful specific temperatures [1]- [2].
The integration of PCMs into cellulose matrix during the waste paper recycling process has been developed in order to obtain a
composite material.
Experiments on the productive process for the realization of insulating panels were done in order to make the new material
suitable for building application. The addition of rising agents
demonstrated the possibility to obtain a lighter structure with better
insulation properties.
Several tests were conducted to verify the new panel properties. The results obtained have shown the possibility to realize an
innovative and sustainable material suitable to replace insulating panels currently used.
Abstract: The regulatory competence of blood glucose homeostasis might determine the degree of academic performance. The aim of this study was to produce a model of students' alcohol use based on glucose homeostasis control and cognitive functions that might define the pathogenetic mechanism of alcohol's effect on academic performance. The study took six hours and thirty minutes on fasting, involving thirteen male students. Disturbances in cognitive functions, precisely a decrease in the effectiveness of active attention and a faster development of fatigue after four to six hours of mental work in alcohol users, compared to abstainers was statistically proven. These disturbances in alcohol users were retained even after seven to ten days of moderate alcohol use and might be the reason for the low academic performances among students who use alcoholic beverages.