Abstract: This paper investigates the performance of Multiple- Input Multiple-Output (MIMO) feedback system combined with Orthogonal Frequency Division Multiplexing (OFDM). Two types of codebook based channel feedback techniques are used in this work. The first feedback technique uses a combination of both the long-term and short-term channel state information (CSI) at the transmitter, whereas the second technique uses only the short term CSI. The long-term and short-term CSI at the transmitter is used for efficient channel utilization. OFDM is a powerful technique employed in communication systems suffering from frequency selectivity. Combined with multiple antennas at the transmitter and receiver, OFDM proves to be robust against delay spread. Moreover, it leads to significant data rates with improved bit error performance over links having only a single antenna at both the transmitter and receiver. The effectiveness of these techniques has been demonstrated through the simulation of a MIMO-OFDM feedback system. The results have been evaluated for 4x4 MIMO channels. Simulation results indicate the benefits of the MIMO-OFDM channel feedback system over the one without incorporating OFDM. Performance gain of about 3 dB is observed for MIMO-OFDM feedback system as compared to the one without employing OFDM. Hence MIMO-OFDM becomes an attractive approach for future high speed wireless communication systems.
Abstract: Radio wave propagation on the road surface is a major
problem on wireless sensor network for traffic monitoring. In this
paper, we compare receiving signal strength on two scenarios 1) an
empty road and 2) a road with a vehicle. We investigate the effect of
antenna polarization and antenna height to the receiving signal
strength. The transmitting antenna is installed on the road surface.
The receiving signal is measured 360 degrees around the transmitting
antenna with the radius of 2.5 meters. Measurement results show the
receiving signal fluctuation around the transmitting antenna in both
scenarios. Receiving signal with vertical polarization antenna results
in higher signal strength than horizontal polarization antenna. The
optimum antenna elevation is 1 meter for both horizon and vertical
polarizations with the vehicle on the road. In the empty road, the
receiving signal level is unvarying with the elevation when the
elevation is greater than 1.5 meters.
Abstract: Present wireless communication demands compact and intelligent devices with multitasking capabilities at affordable cost. The focus in the presented paper is on a dual band antenna for wireless communication with the capability of operating at two frequency bands with same structure. Two resonance frequencies are observed with the second operation band at 4.2GHz approximately three times the first resonance frequency at 1.5GHz. Structure is simple loop of microstrip line with characteristic impedance 50 ohms. The proposed antenna is designed using defective ground structure (DGS) and shows the nearly one third reductions in size as compared to without DGS. This antenna was simulated on electromagnetic (EM) simulation software and fabricated using microwave integrated circuit technique on RT-Duroid dielectric substrate (εr= 2.22) of thickness (H=15 mils). The designed antenna was tested on automatic network analyzer and shows the good agreement with simulated results. The proposed structure is modeled into an equivalent electrical circuit and simulated on circuit simulator. Subsequently, theoretical analysis was carried out and simulated. The simulated, measured, equivalent circuit response, and theoretical results shows good resemblance. The bands of operation draw many potential applications in today’s wireless communication.
Abstract: Exact expressions for bit-error probability (BEP) for
coherent square detection of uncoded and coded M-ary quadrature
amplitude modulation (MQAM) using an array of antennas with
maximal ratio combining (MRC) in a flat fading channel interference
limited system in a Nakagami-m fading environment is derived. The
analysis assumes an arbitrary number of independent and identically
distributed Nakagami interferers. The results for coded MQAM are
computed numerically for the case of (24,12) extended Golay code
and compared with uncoded MQAM by plotting error probabilities
versus average signal-to-interference ratio (SIR) for various values of
order of diversity N, number of distinct symbols M, in order to
examine the effect of cochannel interferers on the performance of the
digital communication system. The diversity gains and net gains are
also presented in tabular form in order to examine the performance of
digital communication system in the presence of interferers, as the
order of diversity increases. The analytical results presented in this
paper are expected to provide useful information needed for design
and analysis of digital communication systems with space diversity
in wireless fading channels.
Abstract: This report aims to utilize existing and future Multiple-Input Multiple-Output Orthogonal Frequency Division Multiplexing Wireless Local Area Network (MIMO-OFDM WLAN) systems characteristics–such as multiple subcarriers, multiple antennas, and channel estimation characteristics–for indoor location estimation systems based on the Direction of Arrival (DOA) and Radio Signal Strength Indication (RSSI) methods. Hybrid of DOA-RSSI methods also evaluated. In the experimental data result, we show that location estimation accuracy performances can be increased by minimizing the multipath fading effect. This is done using multiple subcarrier frequencies over wideband frequencies to estimate one location. The proposed methods are analyzed in both a wide indoor environment and a typical room-sized office. In the experiments, WLAN terminal locations are estimated by measuring multiple subcarriers from arrays of three dipole antennas of access points (AP). This research demonstrates highly accurate, robust and hardware-free add-on software for indoor location estimations based on a MIMO-OFDM WLAN system.
Abstract: Not all types of mobile phone are successful in entering the market because some types of the mobile phone have a negative perception of user. Therefore, it is important to understand the influence of mobile phone's characteristics in the local user perception. This research investigates the influence of QWERTY mobile phone's forms in the perception of Indonesian user. First, some alternatives of mobile phone-s form are developed based on a certain number of mobile phone's models. At the second stage, some word pairs as design attributes of the mobile phone are chosen to represent the user perception of mobile phone. At the final stage, a survey is conducted to investigate the influence of the developed form alternatives to the user perception. Based on the research, users perceive mobile phone's form with curved top and straight bottom shapes and mobile phone's form with slider and antenna as the most negative form. Meanwhile, mobile phone's form with curved top and bottom shapes and mobile phone-s form without slider and antenna are perceived by the user as the most positive form.
Abstract: A novel direction-of-arrival (DOA) estimation technique, which uses a conventional multiple signal classification (MUSIC) algorithm with periodic signals, is applied to a single RF-port parasitic array antenna for direction finding. Simulation results show that the proposed method gives high resolution (1 degree) DOA estimation in an uncorrelated signal environment. The novelty lies in that the MUSIC algorithm is applied to a simplified antenna configuration. Only one RF port and one analogue-to-digital converter (ADC) are used in this antenna, which features low DC power consumption, low cost, and ease of fabrication. Modifications to the conventional MUSIC algorithm do not bring much additional complexity. The proposed technique is also free from the negative influence by the mutual coupling between elements. Therefore, the technique has great potential to be implemented into the existing wireless mobile communications systems, especially at the power consumption limited mobile terminals, to provide additional position location (PL) services.
Abstract: We propose a downlink multiple-input multipleoutput
(MIMO) multi-carrier code division multiple access (MCCDMA)
system with adaptive beamforming algorithm for smart
antennas. The algorithm used in this paper is based on the Least
Mean Square (LMS), with pilot channel estimation (PCE) and the
zero forcing equalizer (ZFE) in the receiver, requiring reference
signal and no knowledge channel. MC-CDMA is studied in a
multiple antenna context in order to efficiently exploit robustness
against multipath effects and multi-user flexibility of MC-CDMA and
channel diversity offered by MIMO systems for radio mobile
channels. Computer simulations, considering multi-path Rayleigh
Fading Channel, interference inter symbol and interference are
presented to verify the performance. Simulation results show that the
scheme achieves good performance in a multi-user system.
Abstract: The nature of wireless ad hoc and sensor networks
make them very attractive to attackers. One of the most popular and
serious attacks in wireless ad hoc networks is wormhole attack and
most proposed protocols to defend against this attack used
positioning devices, synchronized clocks, or directional antennas.
This paper analyzes the nature of wormhole attack and existing
methods of defending mechanism and then proposes round trip time
(RTT) and neighbor numbers based wormhole detection mechanism.
The consideration of proposed mechanism is the RTT between two
successive nodes and those nodes- neighbor number which is needed
to compare those values of other successive nodes. The identification
of wormhole attacks is based on the two faces. The first consideration
is that the transmission time between two wormhole attack affected
nodes is considerable higher than that between two normal neighbor
nodes. The second detection mechanism is based on the fact that by
introducing new links into the network, the adversary increases the
number of neighbors of the nodes within its radius. This system does
not require any specific hardware, has good performance and little
overhead and also does not consume extra energy. The proposed
system is designed in ad hoc on-demand distance vector (AODV)
routing protocol and analysis and simulations of the proposed system
are performed in network simulator (ns-2).
Abstract: This paper proposes a power-controlled scheduling scheme for devices using a directional antenna in smart home. In the case of the home network using directional antenna, devices can concurrently transmit data in the same frequency band. Accordingly, the throughput increases compared to that of devices using omni-directional antenna in proportional to the number of concurrent transmissions. Also, the number of concurrent transmissions depends on the beamwidth of antenna, the number of devices operating in the network , transmission power, interference and so on. In particular, the less transmission power is used, the more concurrent transmissions occur due to small transmission range. In this paper, we considered sub-optimal scheduling scheme for throughput maximization and power consumption minimization. In the scheme, each device is equipped with a directional antenna. Various beamwidths, path loss components, and antenna radiation efficiencies are considered. Numerical results show that the proposed schemes outperform the scheduling scheme using directional antennas without power control.
Abstract: An array antenna system with innovative signal
processing can improve the resolution of a source direction of arrival
(DoA) estimation. High resolution techniques take the advantage of
array antenna structures to better process the incoming waves. They
also have the capability to identify the direction of multiple targets.
This paper investigates performance of the DOA estimation
algorithm namely; Capon and MUSIC on the uniform linear array
(ULA). The simulation results show that in Capon and MUSIC
algorithm the resolution of the DOA techniques improves as number
of snapshots, number of array elements, signal-to-noise ratio and
separation angle between the two sources θ increases.
Abstract: In this paper we have developed a FDTD simulation
code which can treat wave propagation of a monopole antenna in a
metallic case which covers with PML, and performed a series of three
dimensional FDTD simulations of electromagnetic wave propagation
in this space .We also provide a measurement set up in antenna lab
and fortunately the simulations and measurements show good
agreement. According to simulation and measurement results, we
confirmed that the computer program which had been written in
FORTRAN, works correctly.
Abstract: Microstrip antennas are conformable to planar and
nonplanar surfaces, simple and inexpensive to fabricate using modern
printed-circuit technology. Circular polarization of low-profile
microstrip patch with high bandwidth is achieved in this research
through the use of a three-cross-arms branch-line coupler with
sequential rotated arrays, another low-profile antenna of hollow
cylinder is also proposed and the function of reconnaissance with
microstrip antenna on Mini UAV (unmanned aerial vehicle) are
evaluated in practical flight test.
Abstract: SDMA (Space-Division Multiple Access) is a MIMO
(Multiple-Input and Multiple-Output) based wireless communication
network architecture which has the potential to significantly increase
the spectral efficiency and the system performance. The maximum
likelihood (ML) detection provides the optimal performance, but its
complexity increases exponentially with the constellation size of
modulation and number of users. The QR decomposition (QRD)
MUD can be a substitute to ML detection due its low complexity and
near optimal performance. The minimum mean-squared-error
(MMSE) multiuser detection (MUD) minimises the mean square
error (MSE), which may not give guarantee that the BER of the
system is also minimum. But the minimum bit error rate (MBER)
MUD performs better than the classic MMSE MUD in term of
minimum probability of error by directly minimising the BER cost
function. Also the MBER MUD is able to support more users than
the number of receiving antennas, whereas the rest of MUDs fail in
this scenario. In this paper the performance of various MUD
techniques is verified for the correlated MIMO channel models based
on IEEE 802.16n standard.
Abstract: This paper presents the utilizing of ferroelectric
material on antenna application. There are two different ferroelectric
had been used on the proposed antennas which include of Barium
Strontium Titanate (BST) and Bismuth Titanate (BiT), suitable for
Access Points operating in the WLAN IEEE 802.11 b/g and WiMAX
IEEE 802.16 within the range of 2.3 GHz to 2.5 GHz application.
BST, which had been tested to own a dielectric constant of εr = 15
while BiT has a dielectric constant that higher than BST which is εr =
21 and both materials are in rectangular shaped. The influence of
various parameters on antenna characteristics were investigated
extensively using commercial electromagnetic simulations software
by Communication Simulation Technology (CST). From theoretical
analysis and simulation results, it was demonstrated that ferroelectric
material used have not only improved the directive emission but also
enhanced the radiation efficiency.
Abstract: In this paper, we proposed a new routing protocol for
Unmanned Aerial Vehicles (UAVs) that equipped with directional
antenna. We named this protocol Directional Optimized Link State
Routing Protocol (DOLSR). This protocol is based on the well
known protocol that is called Optimized Link State Routing Protocol
(OLSR). We focused in our protocol on the multipoint relay (MPR)
concept which is the most important feature of this protocol. We
developed a heuristic that allows DOLSR protocol to minimize
the number of the multipoint relays. With this new protocol the
number of overhead packets will be reduced and the End-to-End
delay of the network will also be minimized. We showed through
simulation that our protocol outperformed Optimized Link State
Routing Protocol, Dynamic Source Routing (DSR) protocol and Ad-
Hoc On demand Distance Vector (AODV) routing protocol in
reducing the End-to-End delay and enhancing the overall
throughput. Our evaluation of the previous protocols was based
on the OPNET network simulation tool.
Abstract: This paper present a circular patch microstrip array antenna operate in KU-band (10.9GHz – 17.25GHz). The proposed circular patch array antenna will be in light weight, flexible, slim and compact unit compare with current antenna used in KU-band. The paper also presents the detail steps of designing the circular patch microstrip array antenna. An Advance Design System (ADS) software is used to compute the gain, power, radiation pattern, and S11 of the antenna. The proposed Circular patch microstrip array antenna basically is a phased array consisting of 'n' elements (circular patch antennas) arranged in a rectangular grid. The size of each element is determined by the operating frequency. The incident wave from satellite arrives at the plane of the antenna with equal phase across the surface of the array. Each 'n' element receives a small amount of power in phase with the others. There are feed network connects each element to the microstrip lines with an equal length, thus the signals reaching the circular patches are all combined in phase and the voltages add up. The significant difference of the circular patch array antenna is not come in the phase across the surface but in the magnitude distribution.
Abstract: Artificial Neural Network (ANN)s are best suited for
prediction and optimization problems. Trained ANNs have found
wide spread acceptance in several antenna design systems. Four
parameters namely antenna radiation resistance, loss resistance, efficiency,
and inductance can be used to design an antenna layout though
there are several other parameters available. An ANN can be trained
to provide the best and worst case precisions of an antenna design
problem defined by these four parameters. This work describes the
use of an ANN to generate the four mentioned parameters for a loop
antenna for the specified frequency range. It also provides insights
to the prediction of best and worst-case design problems observed
in applications and thereby formulate a model for physical layout
design of a loop antenna.
Abstract: This paper considers the problem of Null-Steering beamforming using Neural Network (NN) approach for antenna array system. Two cases are presented. First, unlike the other authors, the estimated Direction Of Arrivals (DOAs) are used for antenna array weights NN-based determination and the imprecise DOAs estimations are taken into account. Second, the blind null-steering beamforming is presented. In this case the antenna array outputs are presented at the input of the NN without DOAs estimation. The results of computer simulations will show much better relative mean error performances of the first NN approach compared to the NNbased blind beamforming.
Abstract: Synthetic Aperture Radar (SAR) is an imaging radar form by taking full advantage of the relative movement of the antenna with respect to the target. Through the simultaneous processing of the radar reflections over the movement of the antenna via the Range Doppler Algorithm (RDA), the superior resolution of a theoretical wider antenna, termed synthetic aperture, is obtained. Therefore, SAR can achieve high resolution two dimensional imagery of the ground surface. In addition, two filtering steps in range and azimuth direction provide accurate enough result. This paper develops a simulation in which realistic SAR images can be generated. Also, the effect of velocity errors in the resulting image has also been investigated. Taking some velocity errors into account, the simulation results on the image resolution would be presented. Most of the times, algorithms need to be adjusted for particular datasets, or particular applications.