Abstract: Theoretical optimization of a copper-water negative
inclination heat pipe with internal composite wick structure had been
performed, regarding a new introduced parameter: the ratio between
the coarse mesh wraps and the fine mesh wraps of the composite
wick. Since in many cases, the design of a heat pipe matches specific
thermal requirements and physical limitations, this work
demonstrates the optimization of a 1m length, 8mm internal diameter
heat pipe without an adiabatic section, at a negative inclination angle
of -10º. The optimization is based on a new introduced parameter, LR:
the ratio between the coarse mesh wraps and the fine mesh wraps.
Abstract: In the present work, the effects of additives, including
contents of the added antioxidants and type of the selected metallic
stearates (either calcium stearate (CaSt) or zinc stearate (ZnSt)), on
the thermal stabilities of carbon black (CB)/high density polyethylene
(HDPE) compounds were studied. The results showed that the AO
contents played a key role in the thermal stabilities of the CB/HDPE
compounds — the higher the AO content, the higher the thermal
stabilities. Although the CaSt-containing compounds were slightly
superior to those with ZnSt in terms of the thermal stabilities, the
remaining solid residue of CaSt after heated to the temperature of 600
°C (mainly calcium carbonate (CaCO3) as characterized by the X-ray
diffraction (XRD) technique) seemed to catalyze the decomposition
of CB in the HDPE-based compounds. Hence, the quantification of
CB in the CaSt-containing compounds with a muffle furnace gave an
inaccurate CB content — much lower than actual value. However,
this phenomenon was negligible in the ZnSt-containing system.
Abstract: Polyethylene (PE), Polypropylene (PP), Polyethylene
(vinyl acetate) (EVA) and PE-ionomer nanocomposite samples were
prepared by mixing of the polymer with organofilized
montmorillonite fillers Cloisite 93A and Dellite 67G. The amount of
each modified montmorillonite (MMT) was fixed to 5% (w/w). The
twin-screw kneader was used for the compounding of polymer matrix
and chosen nanofillers. The level of MMT exfoliation was studied by
the transmission electron microscopy (TEM) observations. The
mechanical properties of prepared materials were evaluated by
dynamical mechanical analysis at 30°C and by the measurement of
tensile properties (stress and strain at break).
Abstract: OEE has been used in many industries as measure of
performance. However due to limitations of original OEE, it has been
modified by various researchers. OEE for mining application is
special version of classic equation, carries these limitation over. In
this paper it has been aimed to modify the OEE for mining
application by introducing the weights to the elements of it and
termed as Mine Production index (MPi). As a special application of
new index MPishovel has been developed by authors. This can be used
for evaluating the shovel effectiveness. Based on analysis, utilization
followed by performance and availability were ranked in this order.
To check the applicability of this index, a case study was done on
four electrical and one hydraulic shovel in a Swedish mine. The
results shows that MPishovel can evaluate production effectiveness of
shovels and can determine effectiveness values in optimistic view
compared to OEE. MPi with calculation not only give the
effectiveness but also can predict which elements should be focused
for improving the productivity.
Abstract: This study is an attempt to raise the awareness of the
stakeholders and the authorities on the sensitivity of Algerian
secondary school teachers of English as a Foreign Language about
the students’ loss of English language skills learned during formal
schooling with effort and at expense and the supposed measures to
arrest that loss. Data was collected from secondary school teachers of
EFL and analyzed quantitatively using a questionnaire containing
open-ended and close-ended questions. The results advocate a
consensus about the need for actions to be adopted to make
assessment techniques outcome-oriented. Most of the participants
were in favor of including curricular activities involving
contextualized learning, problem-solving learning critical selfawareness,
self and peer-assisted learning, use of computers and
internet so as to make learners autonomous.
Abstract: Different order modulations combined with different
coding schemes, allow sending more bits per symbol, thus achieving
higher throughputs and better spectral efficiencies. However, it must
also be noted that when using a modulation technique such as 64-
QAM with less overhead bits, better signal-to-noise ratios (SNRs) are
needed to overcome any Inter symbol Interference (ISI) and maintain
a certain bit error ratio (BER). The use of adaptive modulation allows
wireless technologies to yielding higher throughputs while also
covering long distances. The aim of this paper is to implement an
Adaptive Modulation and Coding (AMC) features of the WiMAX
PHY in MATLAB and to analyze the performance of the system in
different channel conditions (AWGN, Rayleigh and Rician fading
channel) with channel estimation and blind equalization. Simulation
results have demonstrated that the increment in modulation order
causes to increment in throughput and BER values. These results
derived a trade-off among modulation order, FFT length, throughput,
BER value and spectral efficiency. The BER changes gradually for
AWGN channel and arbitrarily for Rayleigh and Rician fade
channels.
Abstract: Information and Communication Technologies (ICTs)
are pervasive nowadays, including in education where they are
expected to improve the performance of learners. However, the hope
placed in ICTs to find viable solutions to the problem of poor
academic performance in schools in the developing world has not yet
yielded the expected benefits. This problem serves as a motivation to
this study whose aim is to examine the perceptions of educators on
the advantages and disadvantages of e-learning. This aim will be
subdivided into two types of research objectives. Objectives on the
identification and design of theories and models will be achieved
using content analysis and literature review. However, the objective
on the empirical testing of such theories and models will be achieved
through the survey of educators from different schools in the
Pinetown District of the South African Kwazulu-Natal province.
SPSS is used to quantitatively analyse the data collected by the
questionnaire of this survey using descriptive statistics and Pearson
correlations after assessing the validity and the reliability of the data.
The main hypothesis driving this study is that there is a relationship
between the demographics of educators’ and their adherence to
learning theories on one side, and their perceptions on the advantages
and disadvantages of e-learning on the other side, as argued by
existing research; but this research views these learning theories
under three perspectives: educators’ adherence to self-regulated
learning, to constructivism, and to progressivism. This hypothesis
was fully confirmed by the empirical study except for the
demographic factor where teachers’ level of education was found to
be the only demographic factor affecting the perceptions of educators
on the advantages and disadvantages of e-learning.
Abstract: This paper presents a new method to design nonlinear
feedback linearization controller for PEMFCs (Polymer Electrolyte
Membrane Fuel Cells). A nonlinear controller is designed based on
nonlinear model to prolong the stack life of PEMFCs. Since it is
known that large deviations between hydrogen and oxygen partial
pressures can cause severe membrane damage in the fuel cell,
feedback linearization is applied to the PEMFC system so that the
deviation can be kept as small as possible during disturbances or load
variations. To obtain an accurate feedback linearization controller,
tuning the linear parameters are always important. So in proposed
study NSGA (Non-Dominated Sorting Genetic Algorithm)-II method
was used to tune the designed controller in aim to decrease the
controller tracking error. The simulation result showed that the
proposed method tuned the controller efficiently.
Abstract: Ongoing landscape transformation is one of the major
causes behind disappearance of traditional landscapes, and lead to
species and resource loss. Tree in paddy fields in the northeast of
Thailand is one of those traditional landscapes. Using three different
historical time layers, we acknowledged the severe deforestation and
rapid urbanization happened in the region. Despite the general
thinking of decline in tree density as consequences, the heterogeneous
trend of changes in total tree density in three studied landscapes denied
the hypothesis that number of trees in paddy field depend on the length
of land use practice. On the other hand, due to selection of planting
new trees on levees, existence of trees in paddy field now relies on
their values for human use. Besides, changes in land use and landscape
structure had a significant impact on decision of which tree density
level is considered as suitable for the landscape.
Abstract: The majority of contemporary insulation materials
commonly used in the building industry is made from non-renewable
raw materials; furthermore, their production often brings high energy
costs. A long-term trend as far as sustainable development is
concerned has been the reduction of energy and material demands of
building material production. One of the solutions is the possibility of
using easily renewable natural raw material sources which are
considerably more ecological and their production is mostly less
energy-consuming compared to the production of normal insulations
(mineral wool, polystyrene). The paper describes the results of
research focused on the development of thermal and acoustic
insulation materials based on natural fibres intended for floor
constructions. Given the characteristic open porosity of natural fibre
materials, the hygrothermal behaviour of the developed materials was
studied. Especially the influence of relative humidity and temperature
on thermal insulation properties was observed.
Abstract: The effect of Zn2+, Mg2+, and Ba2+ on Saccharomyces
pastorianus performance was evaluated in this study at independent
and three variable combinations. After 96 h of fermentation, high
wort fermentability (%F) = 29.53 was obtained in medium containing
900:4 ppm Mg2+ + Ba2+. Increased ethanol yield 7.35 %(v/v) and
7.13 %(v/v) were obtained in media containing 900:4 ppm Mg2+ +
Ba2+ and 12:900 ppm Zn2+ + Mg2+. Decrease %F = 22.54 and ethanol
yield 6.18 % (v/v) was obtained in medium containing 12:4 ppm Zn2+
+ Ba2+. In media containing the individual ions, increased %F =
27.94 and 26.03 were recorded for media containing 700 ppm Mg2+
and 2 ppm Ba2+ , with ethanol yield of 7.88% (v/v) and 7.62% (v/v)
respectively. Reduced %F and ethanol yield was observed for 10 ppm
Zn2+ and 4 ppm Ba2+ media. The impact of Ba2+ at 1 and 2 ppm was
significant.
Abstract: This study was conducted to evaluate the manganese
removal from aqueous solution using Banana peels activated carbon
(BPAC). Batch experiments have been carried out to determine the
influence of parameters such as pH, biosorbent dose, initial metal ion
concentrations and contact times on the biosorption process. From
these investigations, a significant increase in percentage removal of
manganese 97.4% is observed at pH value 5.0, biosorbent dose 0.8 g,
initial concentration 20 ppm, temperature 25 ± 2°C, stirring rate 200
rpm and contact time 2h. The equilibrium concentration and the
adsorption capacity at equilibrium of the experimental results were
fitted to the Langmuir and Freundlich isotherm models; the Langmuir
isotherm was found to well represent the measured adsorption data
implying BPAC had heterogeneous surface. A raw groundwater
samples were collected from Baharmos groundwater treatment plant
network at Embaba and Manshiet Elkanater City/District-Giza,
Egypt, for treatment at the best conditions that reached at first phase
by BPAC. The treatment with BPAC could reduce iron and
manganese value of raw groundwater by 91.4% and 97.1%,
respectively and the effect of the treatment process on the
microbiological properties of groundwater sample showed decrease
of total bacterial count either at 22°C or at 37°C to 85.7% and 82.4%,
respectively. Also, BPAC was characterized using SEM and FTIR
spectroscopy.
Abstract: The paper deals with current issues in research of
advanced methods to increase reliability of traditional timber
structural elements. It analyses the issue of strengthening of bent
timber beams, such as ceiling beams in old (historical) buildings with
additional concrete slab in combination with externally bonded fibre -
reinforced polymer. The paper describes experimental testing of
composite timber-concrete beam with FRP reinforcement and
compares results with FEM analysis.
Abstract: As the human race will continue to explore the space
by creating new space transportation means and sending them to other
planets, the enhance of atmospheric reentry study is crucial. In this
context, an analysis of mass recession rate of ablative materials for
thermal shields of reentry spacecrafts is important to be carried out.
The paper describes a new estimation method for calculating the mass
recession of an ablator system made of carbon fiber reinforced plastic
materials. This method is based on Arrhenius equation for low
temperatures and, for high temperatures, on a theory applied for the
recession phenomenon of carbon fiber reinforced plastic materials,
theory which takes into account the presence of the resin inside the
materials. The space mission of USERS spacecraft is considered as a
case study.
Abstract: This paper presents a model predictive control (MPC)
of a utility interactive (UI) single phase inverter (SPI) for a
photovoltaic (PV) system at residential/distribution level. The
proposed model uses single-phase phase locked loop (PLL) to
synchronize SPI with the grid and performs MPC control in a dq
reference frame. SPI model consists of boost converter (BC),
maximum power point tracking (MPPT) control, and a full bridge
(FB) voltage source inverter (VSI). No PI regulators to tune and
carrier and modulating waves are required to produce switching
sequence. Instead, the operational model of VSI is used to synthesize
sinusoidal current and track the reference. Model is validated using a
three kW PV system at the input of UI-SPI in Matlab/Simulink.
Implementation and results demonstrate simplicity and accuracy, as
well as reliability of the model.
Abstract: The effect of particle size on shear strength of
granular materials are investigated using direct shear tests. Small
direct shear test (60 mm by 60 mm by 24 mm deep) were conducted
for particles passing the sieves with opening size of 2.36 mm.
Meanwhile, particles passing the standard 20 mm sieves were tested
using large direct shear test (300 mm by 300 mm by 200 mm deep).
The large direct shear tests and the small direct shear tests carried out
using the same shearing rate of 0.09 mm/min and similar normal
stresses of 100, 200 and 300 kPa. The results show that the peak and
residual shear strength increases as particle size increases.
Abstract: This paper focuses on the presentation of results
which were obtained as a part of the project FR-TI 3/742: “System of
Lightweight Materials for Finishing of Buildings with Waste Raw
Materials”. Attention was paid to the light weighting of polymermodified
mortars applicable as adhesives, screeds and repair mortars.
In terms of repair mortars, they were ones intended for the sanitation
of aerated concrete.
Abstract: One- and two-dimensional carbon nanostructures with
sp2 hybridization of carbon atoms (single walled carbon nanotubes
and graphene) are promising materials in future electronic and
spintronics devices due to specific character of their electronic
structure. In this paper we present a comparative study of graphene
and single-wall carbon nanotubes by Raman spectro-microscopy in
strong magnetic field. This unique method allows to study changes in
electronic band structure of the two types of carbon nanostructures
induced by a strong magnetic field.
Abstract: WiMAX is a telecommunications technology and it is
specified by the Institute of Electrical and Electronics Engineers Inc.,
as the IEEE 802.16 standard. The goal of this technology is to
provide a wireless data over long distances in a variety of ways. IEEE
802.16 is a recent standard for mobile communication. In this paper,
we provide an overview of various key management algorithms to
provide security for WiMAX.
Abstract: This paper presents a hybrid three phase rectifier for
high power factor application. This rectifier is composed by zero
voltage transition (ZVT) and zero current transition (ZCT) boost
converter with three phase diode bridge rectifier, in parallel with a six
pulse three phase pulse width modulation (PWM) controlled rectifier.
The proposed topology is capable of high power factor with DC
output voltage regulation by providing sinusoidal input. Also, it
increases the overall efficiency of the new hybrid rectifier to 94.56%
and the total harmonic distortion of the hybrid structure varies from
0% to 16% at nominal output power. This topology was simulated in
MATLAB/SIMULINK environment and the output waveforms
presented with experimental result.