Abstract: This study attempts to investigate the relationship
between internal CSR practices and organizational commitment
based on the social exchange theory (SET). Specifically, we examine
the impact of five dimensions of internal CSR practices on
organizational commitment: health and safety, human rights, training
and education, work life balance and workplace diversity. The
proposed model was tested on a sample of 336 frontline employees
within the banking sector in Jordan. Results showed that all internal
CSR dimensions are significantly and positively related to affective
and normative commitment. In addition, the findings of this study
indicate that all internal CSR dimensions did not have a significant
relationship with continuance commitment. Limitations of the study,
directions for future research, and implications of the findings are
discussed.
Abstract: The contribution is dealing with the influence of high speed parameters on the quality of machined surface. In general the principle of high speed cutting lies in achieving faster machine times with concurrent increase in accuracy and quality of the machined areas in largely irregular, mathematically hard to define shapes. High speed machining is a highly effective method of machining with the following goals: increasing of machining productivity, increasing of quality of the machined surface, improving of machining economy, improving of ecological aspects of machining. This article is based on an experiment performed by the Department of Machining and Assembly of the Faculty of Mechanical Engineering of VŠBTechnical University of Ostrava.
Abstract: Load managing method on road became necessary
since overloaded vehicles occur damage on road facilities and existing
systems for preventing this damage still show many
problems.Accordingly, efficient managing system for preventing
overloaded vehicles could be organized by using the road itself as a
scale by applying genetic algorithm to analyze the load and the drive
information of vehicles.Therefore, this paper organized Ubiquitous
sensor network system for development of intelligent overload vehicle
regulation system, also in this study, to use the behavior of road, the
transformation was measured by installing underground box type
indoor model and indoor experiment was held using genetic algorithm.
And we examined wireless possibility of overloaded vehicle
regulation system through experiment of the transmission and
reception distance.If this system will apply to road and bridge, might
be effective for economy and convenience through establishment of
U-IT system..
Abstract: The migration-environment nexus has gained increased interest from the social research field over the last years. While straightly connected to human security issues, this theme has pervaded through the media to the public sphere. Therefore, it is important to observe how did the discussions over environmentally induced migrations develop from the scientific basis to the media attention, passing through some political voices, and in which ways might these messages be interpreted within the broader public discourses. To achieve this purpose, the analysis of the press entries between 2004 and 2010 in three of the main Portuguese newspapers shall be presented, specially reflecting upon the events, protagonists, topics, geographical attributions and terms/expressions used to define those who migrate due to environmental degradation or disasters.
Abstract: A large section of the society in Urban India is unable
to afford a basic dwelling unit. Housing shortage due to the rising unafforability makes it logical to consider alternative technologies more seriously for their application How far do these alternative
technologies match up with the conventional techniques? How do these integrate with the present-day need for urban amenities and
facilities? Are the owners of bamboo dwellings, for instance, a part of
the mainstream housing sector, having the same rights and privileges
as those enjoyed by other property owners? Will they have access to loans for building, improving, renovating or repairing their
dwellings? Why do we still hesitate to build a bamboo house for ourselves? Is our policy framework and political resolve in place, to
welcome such alternative technologies? It is time we found these answers, in order to explore the reasons for large-scale nonacceptance,
of a technology proven for its worthiness.
Abstract: Horizontal continuous casting is widely used to
produce semi-finished non-Ferrous products. Homogeneity in the
metallurgical characteristics and mechanical properties for this
product is vital for industrial application. In the present work, the
microstructure and mechanical properties of a horizontal continuous
cast two-phase brass billet have been studied. Impact strength and
hardness variations were examined and the phase composition and
porosity studied with image analysis software. Distinct differences in
mechanical properties were observed between the upper, middle and
lower parts of the billet, which are explained in terms of the
morphology and size of the phase in the microstructure. Hardness
variation in the length of billet is higher in upper area but impact
strength is higher in lower areas.
Abstract: The paper presents the results of a series of
experiments conducted on physical models of Quarter-circle
breakwater (QBW) in a two dimensional monochromatic wave
flume. The purpose of the experiments was to evaluate the reflection
coefficient Kr of QBW models of different radii (R) for different
submergence ratios (d/hc), where d is the depth of water and hc is the
height of the breakwater crest from the sea bed. The radii of the
breakwater models studied were 20cm, 22.5cm, 25cm, 27.5cm and
submergence ratios used varied from 1.067 to 1.667. The wave
climate off the Mangalore coast was used for arriving at the various
model wave parameters. The incident wave heights (Hi) used in the
flume varied from 3 to 18cm, and wave periods (T) ranged from 1.2 s
to 2.2 s. The water depths (d) of 40cm, 45cm and 50cm were used in
the experiments. The data collected was analyzed to compute
variation of reflection coefficient Kr=Hr/Hi (where Hr=reflected wave
height) with the wave steepness Hi/gT2 for various R/Hi
(R=breakwater radius) values. It was found that the reflection
coefficient increased as incident wave steepness increased. Also as
wave height decreases reflection coefficient decreases and as
structure radius R increased Kr decreased slightly.
Abstract: Detecting object in video sequence is a challenging
mission for identifying, tracking moving objects. Background
removal considered as a basic step in detected moving objects tasks.
Dual static cameras placed in front and rear moving platform
gathered information which is used to detect objects. Background
change regarding with speed and direction moving platform, so
moving objects distinguished become complicated. In this paper, we
propose framework allows detection moving object with variety of
speed and direction dynamically. Object detection technique built on
two levels the first level apply background removal and edge
detection to generate moving areas. The second level apply Moving
Areas Filter (MAF) then calculate Correlation Score (CS) for
adjusted moving area. Merging moving areas with closer CS and
marked as moving object. Experiment result is prepared on real scene
acquired by dual static cameras without overlap in sense. Results
showing accuracy in detecting objects compared with optical flow
and Mixture Module Gaussian (MMG), Accurate ratio produced to
measure accurate detection moving object.
Abstract: There have been many games developing simulation
of soccer games. Many of these games have been designed with
highly realistic features to attract more users. Many have also
incorporated better artificial intelligent (AI) similar to that in a real
soccer game. One of the challenging issues in a soccer game is the
cooperation, coordination and negotiation among distributed agents
in a multi-agent system. This paper focuses on the incorporation of
multi-agent technique in a soccer game domain. The better the
cooperation of a multi-agent team, the more intelligent the game will
be. Thus, past studies were done on the robotic soccer game because
of the better multi-agent system implementation. From this study, a
better approach and technique of multi-agent behavior could be
select to improve the author-s 2D online soccer game.
Abstract: This study discusses the effect of uncertainty on
production levels of a petrochemical complex. Uncertainly or
variations in some model parameters, such as prices, supply and
demand of materials, can affect the optimality or the efficiency of any
chemical process. For any petrochemical complex with many plants,
there are many sources of uncertainty and frequent variations which
require more attention. Many optimization approaches are proposed
in the literature to incorporate uncertainty within the model in order
to obtain a robust solution. In this work, a stability analysis approach
is applied to a deterministic LP model of a petrochemical complex
consists of ten plants to investigate the effect of such variations on
the obtained optimal production levels. The proposed approach can
determinate the allowable variation ranges of some parameters,
mainly objective or RHS coefficients, before the system lose its
optimality. Parameters with relatively narrow range of variations, i.e.
stability limits, are classified as sensitive parameters or constraints
that need accurate estimate or intensive monitoring. These stability
limits offer easy-to-use information to the decision maker and help in
understanding the interaction between some model parameters and
deciding when the system need to be re-optimize. The study shows
that maximum production of ethylene and the prices of intermediate
products are the most sensitive factors that affect the stability of the
optimum solution
Abstract: The effect of streamwise conduction on the thermal
characteristics of forced convection for nanofluidic flow in
rectangular microchannel heat sinks under isothermal wall has been
investigated. By applying the fin approach, models with and without
streamwise conduction term in the energy equation were developed
for hydrodynamically and thermally fully-developed flow. These two
models were solved to obtain closed form analytical solutions for the
nanofluid and solid wall temperature distributions and the analysis
emphasized details of the variations induced by the streamwise
conduction on the nanofluid heat transport characteristics. The effects
of the Peclet number, nanoparticle volume fraction, thermal
conductivity ratio on the thermal characteristics of forced convection
in microchannel heat sinks are analyzed. Due to the anomalous
increase in the effective thermal conductivity of nanofluid compared
to its base fluid, the effect of streamwise conduction is expected to be
more significant. This study reveals the significance of the effect of
streamwise conduction under certain conditions of which the
streamwise conduction should not be neglected in the forced
convective heat transfer analysis of microchannel heat sinks.
Abstract: Recurrence of aneurysm rupture can be attributed to
coil migration and compaction. In order to verify the effects of
hemodynamics on coil compaction and migration, we analyze the
forces and displacements on the coil bundle using a computational
method. Lateral aneurysms partially filled coils are modeled, and
blood flow fields and coil deformations are simulated considering
fluid and solid interaction. Effects of aneurysm neck size and parent
vessel geometry are also investigated. The results showed that coil
deformation was larger in the aneurysms with a wider neck. Parent
vessel geometry and aneurysm neck size also affected mean pressure
force profiles on the coil surface. Pressure forces were higher in wide
neck models with curved parent vessel geometry. Simulation results
showed that coils in the wide neck aneurysm with a curved parent
vessel may be displaced and compacted more easily.
Abstract: Message Passing Interface is widely used for Parallel
and Distributed Computing. MPICH and LAM are popular open
source MPIs available to the parallel computing community also
there are commercial MPIs, which performs better than MPICH etc.
In this paper, we discuss a commercial Message Passing Interface, CMPI
(C-DAC Message Passing Interface). C-MPI is an optimized
MPI for CLUMPS. It is found to be faster and more robust compared
to MPICH. We have compared performance of C-MPI and MPICH
on Gigabit Ethernet network.
Abstract: This article deals to describe the simulation
investigation of the digital phase locked loop implemented in
software (SDPLL). SDPLL has been developed for speed drives of an
induction motor in scalar strategy. A drive was implemented and
simulation results are presented to verify the robustness against motor
parameter variation and regulation speed.
Abstract: Friction Stir Welding (FSW) is a solid state welding
process invented and patented by The Welding Institute (TWI) in the
United Kingdom in 1991 for butt and lap welding of metals and plastics. This paper highlights the benefits of friction stir welding
process as an energy efficient and a green technology process in the
field of welding. Compared to the other conventional welding processes, its benefits, typical applications and its use in joining
similar and dissimilar materials are also presented.
Abstract: The purpose of this research study is to investigate the manner in which various loads affect the mechanical properties of the formed mild steel plates. The investigation focuses on examining the cross-sectional area of the metal plate at the centre of the formed mild steel plate. Six mild steel plates were deformed with different loads. The loads applied on the plates had a magnitude of 5 kg, 10 kg, 15 kg, 20 kg, 25 kg and 30 kg. The radius of the punching die was 120 mm and the loads were applied at room temperature. The investigations established that the applied load causes the Vickers microhardness at the cross-sectional area of the plate to increase due to strain hardening. Hence, the percentage increase of the hardness due to the load was found to be directly proportional to the increase in the load. Furthermore, the tensile test results for the parent material showed that the average Ultimate Tensile Strength (UTS) for the three samples was 308 MPa while the average Yield Strength and Percentage Elongation were 227 MPa and 38 % respectively. Similarly, the UTS of the formed components increased after the deformation of the plate, as such it can be concluded that the forming loads alter the mechanical properties of the materials by improving and strengthening the material properties.
Abstract: In the present paper, we present a modification of the
New Iterative Method (NIM) proposed by Daftardar-Gejji and Jafari
[J. Math. Anal. Appl. 2006;316:753–763] and use it for solving
systems of nonlinear functional equations. This modification yields
a series with faster convergence. Illustrative examples are presented
to demonstrate the method.
Abstract: This paper discusses a qualitative simulator QRiOM
that uses Qualitative Reasoning (QR) technique, and a process-based
ontology to model, simulate and explain the behaviour of selected
organic reactions. Learning organic reactions requires the application
of domain knowledge at intuitive level, which is difficult to be
programmed using traditional approach. The main objective of
QRiOM is to help learners gain a better understanding of the
fundamental organic reaction concepts, and to improve their
conceptual comprehension on the subject by analyzing the multiple
forms of explanation generated by the software. This paper focuses
on the generation of explanation based on causal theories to explicate
various phenomena in the chemistry subject. QRiOM has been tested
with three classes problems related to organic chemistry, with
encouraging results. This paper also presents the results of
preliminary evaluation of QRiOM that reveal its explanation
capability and usefulness.
Abstract: The objective of the present research manuscript is to
perform parametric, nonparametric, and decision tree analysis to
evaluate two treatments that are being used for breast cancer patients.
Our study is based on utilizing real data which was initially used in
“Tamoxifen with or without breast irradiation in women of 50 years
of age or older with early breast cancer" [1], and the data is supplied
to us by N.A. Ibrahim “Decision tree for competing risks survival
probability in breast cancer study" [2]. We agree upon certain aspects
of our findings with the published results. However, in this
manuscript, we focus on relapse time of breast cancer patients instead
of survival time and parametric analysis instead of semi-parametric
decision tree analysis is applied to provide more precise
recommendations of effectiveness of the two treatments with respect
to reoccurrence of breast cancer.
Abstract: Implementing Information Technology/ Information
System (IT/IS) is critical for every industry as its potential benefits
have been to motivate many industries including the Malaysian
construction industry to invest in it. To successfully implement IT/IS
has become the major concern for every organisation. Identifying the
critical success factors (CSFs) has become the main agenda for
researchers, academicians and practitioners due to the wide number
of failures reported. This research paper seeks to identify the CSFs
that influence the successful implementation of IT/IS in construction
industry in Malaysia. Limited factors relating to people issue will be
highlighted here to showcase some as it becomes one of the major
contributing factors to the failure. Three (3) organisations have
participated in this study. Semi-structured interviews are employed as
they offer sufficient flexibility to ensure that all relevant factors are
covered. Several key issues contributing to successful
implementations of IT/IS are identified. The results of this study
reveal that top management support, communication, user
involvement, IT staff roles and responsibility, training/skills, leader/
IT Leader, organisation culture, knowledge/ experience, motivation,
awareness, focus and ambition, satisfaction, teamwork/ collaboration,
willingness to change, attitude, commitment, management style,
interest in IT, employee behaviour towards collaborative
environment, trust, interpersonal relationship, personal characteristic
and competencies are significantly associated with the successful
implementations of IT/IS. It is anticipated that this study will create
awareness and contribute to a better understanding amongst
construction industry players and will assist them to successfully
implement IT/IS.