Abstract: This paper gives a study about forging solution to
deploy the fixed wireless access (FWA) in the band 3300-3400MHz
instead of 3400-3600MHz to eschew the harmful interference
between from the FWA towards fixed satellite services receiver
presented in this band. The impact of FWA services toward the FSS
and the boundaries of spectrum emission mask had been considered
to calculate the possible Guard band required in this case. In
addition, supplementary separation distance added to improve the
coexistence between the two adjacent bands. Simulation had been
done using Matlab software base on ITU models reliance on the most
popular specification used for the tropical weather countries. Review
the current problem of interference between two systems and some
mitigation techniques which adopted in Malaysia as a case study is a
part of this research.
Abstract: The effects of global warming on India vary from the
submergence of low-lying islands and coastal lands to the melting of
glaciers in the Indian Himalayas, threatening the volumetric flow rate
of many of the most important rivers of India and South Asia. In
India, such effects are projected to impact millions of lives. As a
result of ongoing climate change, the climate of India has become
increasingly volatile over the past several decades; this trend is
expected to continue.
Climate change is one of the most important global environmental
challenges, with implications for food production, water supply,
health, energy, etc. Addressing climate change requires a good
scientific understanding as well as coordinated action at national and
global level. The climate change issue is part of the larger challenge
of sustainable development. As a result, climate policies can be more
effective when consistently embedded within broader strategies
designed to make national and regional development paths more
sustainable. The impact of climate variability and change, climate
policy responses, and associated socio-economic development will
affect the ability of countries to achieve sustainable development
goals.
A very well calibrated Soil and Water Assessment Tool (R2 =
0.9968, NSE = 0.91) was exercised over the Khatra sub basin of the
Kangsabati River watershed in Bankura district of West Bengal,
India, in order to evaluate projected parameters for agricultural
activities. Evapotranspiration, Transmission Losses, Potential
Evapotranspiration and Lateral Flow to reach are evaluated from the
years 2041-2050 in order to generate a picture for sustainable
development of the river basin and its inhabitants.
India has a significant stake in scientific advancement as well as
an international understanding to promote mitigation and adaptation.
This requires improved scientific understanding, capacity building,
networking and broad consultation processes. This paper is a
commitment towards the planning, management and development of
the water resources of the Kangsabati River by presenting detailed
future scenarios of the Kangsabati river basin, Khatra sub basin, over
the mentioned time period.
India-s economy and societal infrastructures are finely tuned to the
remarkable stability of the Indian monsoon, with the consequence
that vulnerability to small changes in monsoon rainfall is very high.
In 2002 the monsoon rains failed during July, causing profound loss
of agricultural production with a drop of over 3% in India-s GDP.
Neither the prolonged break in the monsoon nor the seasonal rainfall
deficit was predicted. While the general features of monsoon
variability and change are fairly well-documented, the causal
mechanisms and the role of regional ecosystems in modulating the
changes are still not clear. Current climate models are very poor at
modelling the Asian monsoon: this is a challenging and critical
region where the ocean, atmosphere, land surface and mountains all
interact. The impact of climate change on regional ecosystems is
likewise unknown. The potential for the monsoon to become more
volatile has major implications for India itself and for economies
worldwide. Knowledge of future variability of the monsoon system,
particularly in the context of global climate change, is of great
concern for regional water and food security.
The major findings of this paper were that of all the chosen
projected parameters, transmission losses, soil water content,
potential evapotranspiration, evapotranspiration and lateral flow to
reach, display an increasing trend over the time period of years 2041-
2050.
Abstract: Cost contribution arrangements (CCAs) and Cost
sharing agreements (CCAs) belong to the tools of modern finance
management. Costs spend by associated enterprises on developing
producing or obtaining assets, services or rights (in general -
benefits) are used for tax optimizing too. The main purpose of joint
research and development, producing or obtaining benefits is to
lower these costs as much as possible or to maximize the benefits. In
this article is mentioned the problematic of transfer pricing and arm's
length principle with connection of CCAs, CSAs. Next, there is
mentioned how to settle participation shares of the total cost and
benefits contributions with respect to the OECD Transfer pricing for
MNEs Guidelines and with respect to other significant regulations.
Abstract: Most neural network (NN) models of human category learning use a gradient-based learning method, which assumes that locally-optimal changes are made to model parameters on each learning trial. This method tends to under predict variability in individual-level cognitive processes. In addition many recent models of human category learning have been criticized for not being able to replicate rapid changes in categorization accuracy and attention processes observed in empirical studies. In this paper we introduce stochastic learning algorithms for NN models of human category learning and show that use of the algorithms can result in (a) rapid changes in accuracy and attention allocation, and (b) different learning trajectories and more realistic variability at the individual-level.
Abstract: This paper investigates the relationship between different dimensions of customer relationship management and innovation capabilities in Melli Bank of Iran. Five dimensions of CRM include information sharing, customer involvement, long-term partnership, joint problem solving and technology-based CRM are selected to measure their relationship with innovation capabilities including innovation in product, innovation in process, innovation in administrative affairs, innovation in marketing, and finally innovation in services. Research findings indicate that there is significant relationship between CRM dimensions and innovation capabilities in Melli bank of Iran.
Abstract: We deal with the numerical solution of time-dependent convection-diffusion-reaction equations. We combine the local projection stabilization method for the space discretization with two different time discretization schemes: the continuous Galerkin-Petrov (cGP) method and the discontinuous Galerkin (dG) method of polynomial of degree k. We establish the optimal error estimates and present numerical results which shows that the cGP(k) and dG(k)- methods are accurate of order k +1, respectively, in the whole time interval. Moreover, the cGP(k)-method is superconvergent of order 2k and dG(k)-method is of order 2k +1 at the discrete time points. Furthermore, the dependence of the results on the choice of the stabilization parameter are discussed and compared.
Abstract: Chitosan is a biopolymer composed of glucosamine
and N-acetyl glucosamine. Solubility and viscosity pose problems in
some applications. These problems can be overcome with unique
modifications. In this study, firstly, chitosan was modified by caffeic
acid and thioglycolic acid, separately. Then, growing effects of these
modified polymers was observed in U937 cell line. Caffeic acid is a
phenolic compound and its modifications act carcinogenic inhibitors
in drugs. Thiolated chitosans are commonly being used for drugdelivery
systems in various routes, because of enhancing
mucoadhesiveness property. U937 cell line was used model cell for
leukaemia. Modifications were achieved by 1 – 15 % binding range.
Increasing binding ratios showed higher radical-scavenging activity
and reducing cell growth, in compared to native chitosan. Caffeic
acid modifications showed higher radical-scavenging activity than
thiolated chitosans at the same concentrations. Caffeic acid and
thioglycolic acid modifications inhibited growth of U937, effectively.
Abstract: The flow and heat transfer characteristics for natural
convection along an inclined plate in a saturated porous medium with
an applied magnetic field have been studied. The fluid viscosity has
been assumed to be an inverse function of temperature. Assuming
temperature vary as a power function of distance. The transformed
ordinary differential equations have solved by numerical integration
using Runge-Kutta method. The velocity and temperature profile
components on the plate are computed and discussed in detail for
various values of the variable viscosity parameter, inclination angle,
magnetic field parameter, and real constant (λ). The results have also
been interpreted with the aid of tables and graphs. The numerical
values of Nusselt number have been calculated for the mentioned
parameters.
Abstract: An experiment of vented gas explosions involving two
different cylinder vessel volumes (0.2 and 0.0065 m3) was reported,
with equivalence ratio (Φ) ranged from 0.3 to 1.6. Both vessels were
closed at the rear end and fitted at the other side with a circular
orifice plate that gives a constant vent coefficient (K =Av/V2/3) of
16.4. It was shown that end ignition gives higher overpressures than
central ignition, even though most of the published work on venting
uses central ignition. For propane and ethylene, it is found that rich
mixtures gave the highest overpressures and these mixtures are not
considered in current vent design guidance; which the guideline is
based on mixtures giving the maximum flame temperature. A strong
influence of the vessel volume at constant K was found for methane,
propane, ethylene and hydrogen-air explosions. It can be concluded
that self- acceleration of the flame, which is dependent on the
distance of a flame from the ignition and the ‘suction’ at the vent
opening are significant factors affecting the vent flow during
explosion development in vented gas explosion. This additional
volume influence on vented explosions is not taken into account in
the current vent design guidance.
Abstract: In this paper methodology to exploit creeping wave
for body area network BAN communication reliability are described.
Creeping wave propagation effects are visualized & analyzed.
During this work Dipole, IA antennas various antennas were
redesigned using existing designs and their propagation
characteristics were verified for optimum performance when used on
BANs. These antennas were then applied on body shapes-including
rectangular, spherical and cylindrical so that all the effects of actual
human body can be taken nearly into account. Parametric simulation
scheme was devised so that on Body channel characterization can be
visualized at front, curved and back region. In the next phase
multiple inputs multiple output MIMO scheme was introduced where
virtual antennas were used in order to diminish the effects of
antennas on the propagation of waves. Results were, extracted and
analyzed at different heights. Finally based on comparative
measurement and analysis it was concluded that on body propagation
can be exploited to gain spatial diversity.
Abstract: This paper reports an experimental study on a sleeping
thermal manikin in a room equipped with a mixing ventilation
system. In the experimental work, heat loss from the sleeping thermal
manikin was measured under different conditions. The supply air
temperature was in a range of 17°C to 27°C. Apart from the heat loss
of the sleeping thermal manikin, the velocity distributions and
temperature distributions were also measured in the experiments for
subsequent analysis.
Abstract: The aim of the present investigation was to compare
sex differences in thyroid gland structure of rabbits. Five adult male
and five adult female (3.1-3.5 kg body weight) New Zealand white
rabbits were used in the experiment. Results showed that at light
microscopic level, there was no sex difference in microscopic
appearance of the thyroid glands. At electron microscopic level,
however, the mitochondria and the microvilli of the follicular cells
are more numerous and the Golgi complex is also more extensive in
male rabbits in comparison to females. Results obtained from
micrometric measurements showed that the volume density of the
follicles is higher in males than in females, but the differences are not
statistically significant .The volume density of epithelium and the
height of follicular cells are significantly greater in males than in
females and reverse is true about the volume density of interstitium
(p
Abstract: The current speech interfaces in many military
applications may be adequate for native speakers. However,
the recognition rate drops quite a lot for non-native speakers
(people with foreign accents). This is mainly because the nonnative
speakers have large temporal and intra-phoneme
variations when they pronounce the same words. This
problem is also complicated by the presence of large
environmental noise such as tank noise, helicopter noise, etc.
In this paper, we proposed a novel continuous acoustic feature
adaptation algorithm for on-line accent and environmental
adaptation. Implemented by incremental singular value
decomposition (SVD), the algorithm captures local acoustic
variation and runs in real-time. This feature-based adaptation
method is then integrated with conventional model-based
maximum likelihood linear regression (MLLR) algorithm.
Extensive experiments have been performed on the NATO
non-native speech corpus with baseline acoustic model trained
on native American English. The proposed feature-based
adaptation algorithm improved the average recognition
accuracy by 15%, while the MLLR model based adaptation
achieved 11% improvement. The corresponding word error
rate (WER) reduction was 25.8% and 2.73%, as compared to
that without adaptation. The combined adaptation achieved
overall recognition accuracy improvement of 29.5%, and
WER reduction of 31.8%, as compared to that without
adaptation.
Abstract: Circular tubes have been widely used as structural
members in engineering application. Therefore, its collapse behavior
has been studied for many decades, focusing on its energy absorption
characteristics. In order to predict the collapse behavior of members,
one could rely on the use of finite element codes or experiments.
These tools are helpful and high accuracy but costly and require
extensive running time. Therefore, an approximating model of tubes
collapse mechanism is an alternative for early step of design. This
paper is also aimed to develop a closed-form solution of thin-walled
circular tube subjected to bending. It has extended the Elchalakani et
al.-s model (Int. J. Mech. Sci.2002; 44:1117-1143) to include the
rate of energy dissipation of rolling hinge in the circumferential
direction. The 3-D geometrical collapse mechanism was analyzed by
adding the oblique hinge lines along the longitudinal tube within the
length of plastically deforming zone. The model was based on the
principal of energy rate conservation. Therefore, the rates of internal
energy dissipation were calculated for each hinge lines which are
defined in term of velocity field. Inextensional deformation and
perfect plastic material behavior was assumed in the derivation of
deformation energy rate. The analytical result was compared with
experimental result. The experiment was conducted with a number of
tubes having various D/t ratios. Good agreement between analytical
and experiment was achieved.
Abstract: The present work describes an experimental
investigation concerning the determination of viscosity behavior with
shear rate and temperature of edible oils: canola; sunflower; corn;
soybean and the no edible oil: Jatropha curcas. Besides these, it was
tested a blend of canola, corn and sunflower oils as well as sunflower
and soybean biodiesel. Based on experiments, it was obtained shear
stress and viscosity at different shear rates of each sample at 40ºC, as
well as viscosity of each sample at various temperatures in the range
of 24 to 85ºC. Furthermore, it was compared the curves obtained for
the viscosity versus temperature with the curves obtained by
modeling the viscosity dependency on temperature using the Vogel
equation. Also a test in a stationary engine was performed in order to
study the energy generation using blends of soybean oil and soybean
biodiesel with diesel.
Abstract: This paper explores the use of project work in a
content-based instruction in a Rajabhat University, a teacher college,
where student teachers are instructed to perform teaching roles
mainly in basic education level. Its aim is to link theory to practice,
and to help language teachers maximize the full potential of project
work for genuine communication and give real meaning to writing
activity. Two research questions are formulated to guide this study:
a) What is the academic achievement of the students- writing skill
against the 70% attainment target after the use of project to enhance
the skill? and b) To what degree is the development of the students-
writing skills during the course of project to enhance the skill? The
sample of the study comprised of 38 fourth-year English major
students. The data was collected by means of achievement test,
student writing works, and project diary. The scores in the summative
achievement test were analyzed by mean score, standard deviation,
and t-test. Project diary serves as students- record of the language
acquired during the project. List of structures and vocabulary noted in
the diary has shown students- ability to attend to, recognize, and
focus on meaningful patterns of language forms.
Abstract: Congestion control is one of the fundamental issues in computer networks. Without proper congestion control mechanisms there is the possibility of inefficient utilization of resources, ultimately leading to network collapse. Hence congestion control is an effort to adapt the performance of a network to changes in the traffic load without adversely affecting users perceived utilities. AIMD (Additive Increase Multiplicative Decrease) is the best algorithm among the set of liner algorithms because it reflects good efficiency as well as good fairness. Our control model is based on the assumption of the original AIMD algorithm; we show that both efficiency and fairness of AIMD can be improved. We call our approach is New AIMD. We present experimental results with TCP that match the expectation of our theoretical analysis.
Abstract: This study investigated climatic factors associated
with influenza cases in Southern Thailand. The main aim for use
regression analysis to investigate possible causual relationship of
climatic factors and variability between the border of the Andaman
Sea and the Gulf of Thailand. Southern Thailand had the highest
Influenza incidences among four regions (i.e. north, northeast, central
and southern Thailand). In this study, there were 14 climatic factors:
mean relative humidity, maximum relative humidity, minimum
relative humidity, rainfall, rainy days, daily maximum rainfall,
pressure, maximum wind speed, mean wind speed, sunshine duration,
mean temperature, maximum temperature, minimum temperature,
and temperature difference (i.e. maximum – minimum temperature).
Multiple stepwise regression technique was used to fit the statistical
model. The results indicated that the mean wind speed and the
minimum relative humidity were positively associated with the
number of influenza cases on the Andaman Sea side. The maximum
wind speed was positively associated with the number of influenza
cases on the Gulf of Thailand side.
Abstract: In recent years, the underground water sources in
southern Taiwan have become salinized because of saltwater
intrusions. This study explores the adsorption characteristics of
activated carbon on salinizing inorganic salts using isothermal
adsorption experiments and provides a model analysis. The
temperature range for the isothermal adsorption experiments ranged
between 5 to 45 ℃, and the amount adsorbed varied between 28.21 to
33.87 mg/g. All experimental data of adsorption can be fitted to both
the Langmuir and the Freundlich models. The thermodynamic
parameters for per chlorate onto granular activated carbon were
calculated as -0.99 to -1.11 kcal/mol for DG°, -0.6 kcal/mol for DH°,
and 1.21 to 1.84 kcal/mol for DS°. This shows that the adsorption
process of granular activated carbon is spontaneously exothermic. The
observation of adsorption behaviors under low ionic strength, low pH
values, and low temperatures is beneficial to the adsorption removal of
perchlorate with granular activated carbon.
Abstract: The product development process (PDP) in the
Technology group plays a very important role in the launch of any
product. While a manufacturing process encourages the use of certain
measures to reduce health, safety and environmental (HSE) risks on
the shop floor, the PDP concentrates on the use of Geometric
Dimensioning and Tolerancing (GD&T) to develop a flawless design.
Furthermore, PDP distributes and coordinates activities between
different departments such as marketing, purchasing, and
manufacturing. However, it is seldom realized that PDP makes a
significant contribution to developing a product that reduces HSE
risks by encouraging the Technology group to use effective GD&T.
The GD&T is a precise communication tool that uses a set of
symbols, rules, and definitions to mathematically define parts to be
manufactured. It is a quality assurance method widely used in the oil
and gas sector. Traditionally it is used to ensure the
interchangeability of a part without affecting its form, fit, and
function. Parts that do not meet these requirements are rejected
during quality audits.
This paper discusses how the Technology group integrates this
quality assurance tool into the PDP and how the tool plays a major
role in helping the HSE department in its goal towards eliminating
HSE incidents. The PDP involves a thorough risk assessment and
establishes a method to address those risks during the design stage.
An illustration shows how GD&T helped reduce safety risks by
ergonomically improving assembling operations. A brief discussion
explains how tolerances provided on a part help prevent finger injury.
This tool has equipped Technology to produce fixtures, which are
used daily in operations as well as manufacturing. By applying
GD&T to create good fits, HSE risks are mitigated for operating
personnel. Both customers and service providers benefit from
reduced safety risks.