Rosli - Journal Author

Ecological Risk Assessment of Polycyclic Aromatic Hydrocarbons in the Northwest of the Persian Gulf

Year: 2013 Volume: 7 Issue: 3 167 - 170 Pages

Abstract: This study investigated the presence of polycyclic aromatic hydrocarbons (PAHs) in the sediments of the Musa Bay (around the PETZONE coastal area) from Feb 2010 to Jun 2010. Concentrations of PAHs recorded in the Musa Bay sediments ranged from 537.89 to 26,659.06 ng/g dry weight with a mean value of 3990.74 ng/g. the highest concentration of PAHs was observed at station 4, which is located near the aromatic outlet of Imam Khomeini petrochemical company (station 4: BI-PC Aromatic effluent outlet) in which its concentration level was more than the NOAA sediment quality guideline value (ERL= 4022 ng/g dry weight). Owing to the concentration of PAHs in the study area, its concentration level was still meet the NOAA sediment quality guideline value (ERL: 4022 ng/g dry weight); however, according to the PELq factor, slightly adverse biological effects are associated with the exposure to PAHs levels in the study area (0.1< PELq= 0.24 > 0.5).

Keywords:
Musa Bay
PAHs
PETZONE
NOAA
PELq.

Thermal Analysis of Open-Cycle Regenerator Gas-Turbine Power-Plant

Year: 2010 Volume: 4 Issue: 8 696 - 701 Pages

Abstract: Regenerative gas turbine engine cycle is presented that yields higher cycle efficiencies than simple cycle operating under the same conditions. The power output, efficiency and specific fuel consumption are simulated with respect to operating conditions. The analytical formulae about the relation to determine the thermal efficiency are derived taking into account the effected operation conditions (ambient temperature, compression ratio, regenerator effectiveness, compressor efficiency, turbine efficiency and turbine inlet temperature). Model calculations for a wide range of parameters are presented, as are comparisons with simple gas turbine cycle. The power output and thermal efficiency are found to be increasing with the regenerative effectiveness, and the compressor and turbine efficiencies. The efficiency increased with increase the compression ratio to 5, then efficiency decreased with increased compression ratio, but in simple cycle the thermal efficiency always increase with increased in compression ratio. The increased in ambient temperature caused decreased thermal efficiency, but the increased in turbine inlet temperature increase thermal efficiency.

Unsteady Boundary Layer Flow over a Stretching Sheet in a Micropolar Fluid

Year: 2008 Volume: 2 Issue: 2 136 - 140 Pages

Abstract: Unsteady boundary layer flow of an incompressible micropolar fluid over a stretching sheet when the sheet is stretched in its own plane is studied in this paper. The stretching velocity is assumed to vary linearly with the distance along the sheet. Two equal and opposite forces are impulsively applied along the x-axis so that the sheet is stretched, keeping the origin fixed in a micropolar fluid. The transformed unsteady boundary layer equations are solved numerically using the Keller-box method for the whole transient from the initial state to final steady-state flow. Numerical results are obtained for the velocity and microrotation distributions as well as the skin friction coefficient for various values of the material parameter K. It is found that there is a smooth transition from the small-time solution to the large-time solution.

Pleurotus sajor-caju (PSC) Improves Nutrient Contents and Maintains Sensory Properties of Carbohydrate-based Products

Year: 2012 Volume: 6 Issue: 3 93 - 95 Pages

Abstract: The grey oyster mushroom, Pleurotus sajor-caju (PSC), is a common edible mushroom and is now grown commercially around the world for food. This fungus has been broadly used as food or food ingredients in various food products for a long time. To enhance the nutritional quality and sensory attributes of bakery-based products, PSC powder is used in the present study to partially replace wheat flour in baked product formulations. The nutrient content and sensory properties of rice-porridge and unleavened bread (paratha) incorporated with various levels of PSC powder were studied. These food items were formulated with either 0%, 2%, 4% or 6% of PSC powder. Results show PSC powder recorded β-glucan at 3.57g/100g. In sensory evaluation, consumers gave higher score to both rice-porridge and paratha bread containing 2-4% PSC compared to those that are not added with PSC powder. The paratha containing 4% PSC powder can be formulated with the intention in improving overall acceptability of paratha bread. Meanwhile, for rice-porridge, consumers prefer the formulated product added with 4% PSC powder. In conclusion, the addition of PSC powder to partially wheat flour can be recommended for the purpose of enhancing nutritional composition and maintaining the acceptability of carbohydrate-based products.

A New Approach to ECG Biometric Systems: A Comparitive Study between LPC and WPD Systems

Year: 2010 Volume: 4 Issue: 8 338 - 343 Pages

Abstract: In this paper, a novel method for a biometric system based on the ECG signal is proposed, using spectral coefficients computed through linear predictive coding (LPC). ECG biometric systems have traditionally incorporated characteristics of fiducial points of the ECG signal as the feature set. These systems have been shown to contain loopholes and thus a non-fiducial system allows for tighter security. In the proposed system, incorporating non-fiducial features from the LPC spectrum produced a segment and subject recognition rate of 99.52% and 100% respectively. The recognition rates outperformed the biometric system that is based on the wavelet packet decomposition (WPD) algorithm in terms of recognition rates and computation time. This allows for LPC to be used in a practical ECG biometric system that requires fast, stringent and accurate recognition.

Computational Method for Annotation of Protein Sequence According to Gene Ontology Terms

Year: 2007 Volume: 1 Issue: 1 16 - 29 Pages

Abstract: Annotation of a protein sequence is pivotal for the understanding of its function. Accuracy of manual annotation provided by curators is still questionable by having lesser evidence strength and yet a hard task and time consuming. A number of computational methods including tools have been developed to tackle this challenging task. However, they require high-cost hardware, are difficult to be setup by the bioscientists, or depend on time intensive and blind sequence similarity search like Basic Local Alignment Search Tool. This paper introduces a new method of assigning highly correlated Gene Ontology terms of annotated protein sequences to partially annotated or newly discovered protein sequences. This method is fully based on Gene Ontology data and annotations. Two problems had been identified to achieve this method. The first problem relates to splitting the single monolithic Gene Ontology RDF/XML file into a set of smaller files that can be easy to assess and process. Thus, these files can be enriched with protein sequences and Inferred from Electronic Annotation evidence associations. The second problem involves searching for a set of semantically similar Gene Ontology terms to a given query. The details of macro and micro problems involved and their solutions including objective of this study are described. This paper also describes the protein sequence annotation and the Gene Ontology. The methodology of this study and Gene Ontology based protein sequence annotation tool namely extended UTMGO is presented. Furthermore, its basic version which is a Gene Ontology browser that is based on semantic similarity search is also introduced.

Comparison of MFCC and Cepstral Coefficients as a Feature Set for PCG Biometric Systems

Year: 2010 Volume: 4 Issue: 8 333 - 337 Pages

Abstract: Heart sound is an acoustic signal and many techniques used nowadays for human recognition tasks borrow speech recognition techniques. One popular choice for feature extraction of accoustic signals is the Mel Frequency Cepstral Coefficients (MFCC) which maps the signal onto a non-linear Mel-Scale that mimics the human hearing. However the Mel-Scale is almost linear in the frequency region of heart sounds and thus should produce similar results with the standard cepstral coefficients (CC). In this paper, MFCC is investigated to see if it produces superior results for PCG based human identification system compared to CC. Results show that the MFCC system is still superior to CC despite linear filter-banks in the lower frequency range, giving up to 95% correct recognition rate for MFCC and 90% for CC. Further experiments show that the high recognition rate is due to the implementation of filter-banks and not from Mel-Scaling.

Advanced Neural Network Learning Applied to Pulping Modeling

Year: 2007 Volume: 1 Issue: 7 320 - 323 Pages

Abstract: This paper reports work done to improve the modeling of complex processes when only small experimental data sets are available. Neural networks are used to capture the nonlinear underlying phenomena contained in the data set and to partly eliminate the burden of having to specify completely the structure of the model. Two different types of neural networks were used for the application of pulping problem. A three layer feed forward neural networks, using the Preconditioned Conjugate Gradient (PCG) methods were used in this investigation. Preconditioning is a method to improve convergence by lowering the condition number and increasing the eigenvalues clustering. The idea is to solve the modified odified problem M-1 Ax= M-1b where M is a positive-definite preconditioner that is closely related to A. We mainly focused on Preconditioned Conjugate Gradient- based training methods which originated from optimization theory, namely Preconditioned Conjugate Gradient with Fletcher-Reeves Update (PCGF), Preconditioned Conjugate Gradient with Polak-Ribiere Update (PCGP) and Preconditioned Conjugate Gradient with Powell-Beale Restarts (PCGB). The behavior of the PCG methods in the simulations proved to be robust against phenomenon such as oscillations due to large step size.

Automatic Clustering of Gene Ontology by Genetic Algorithm

Year: 2007 Volume: 1 Issue: 7 2053 - 2062 Pages

Abstract: Nowadays, Gene Ontology has been used widely by many researchers for biological data mining and information retrieval, integration of biological databases, finding genes, and incorporating knowledge in the Gene Ontology for gene clustering. However, the increase in size of the Gene Ontology has caused problems in maintaining and processing them. One way to obtain their accessibility is by clustering them into fragmented groups. Clustering the Gene Ontology is a difficult combinatorial problem and can be modeled as a graph partitioning problem. Additionally, deciding the number k of clusters to use is not easily perceived and is a hard algorithmic problem. Therefore, an approach for solving the automatic clustering of the Gene Ontology is proposed by incorporating cohesion-and-coupling metric into a hybrid algorithm consisting of a genetic algorithm and a split-and-merge algorithm. Experimental results and an example of modularized Gene Ontology in RDF/XML format are given to illustrate the effectiveness of the algorithm.

Effects of Xylanase and Cellulase Production during Composting of EFB and POME using Fungi

Year: 2012 Volume: 6 Issue: 8 594 - 597 Pages

Abstract: Empty Fruit Bunches (EFB) and Palm Oil Mill Effluent (POME) are two main wastes from oil palm industries which contain rich lignocellulose. Degradation of EFB and POME by microorganisms will produce hydrolytic enzyme which will degrade cellulose and hemicellulose during composting process. However, normal composting takes about four to six months to reach maturity. Hence, application of fungi into compost can shorten the period of composting. This study identifies the effect of xylanase and cellulase produced by Aspergillus niger and Trichoderma virens on composting process using EFB and POME. The degradation of EFB and POME indicates the lignocellulolytic capacity of Aspergillus niger and Trichoderma virens with more than 7% decrease in hemicellulose and more than 25% decrease in cellulose for both inoculated compost. Inoculation of Aspergillus niger and Trichoderma virens also increased the enzyme activities during the composting period compared to the control compost by 21% for both xylanase and cellulase. Rapid rise in the activities of cellulase and xylanase was observed by Aspergillus niger with the highest activities of 14.41 FPU/mg and 3.89 IU/mg, respectively. Increased activities of cellulase and xylanase also occurred in inoculation of Trichoderma virens with the highest activities obtained at 13.21 FPU/mg and 4.43 IU/mg, respectively. Therefore, it is evident that the inoculation of fungi can increase the enzyme activities hence effectively degrading the EFB and POME.

Keywords:
EFB
cellulase
POME
xylanase

Modeling of Material Removal on Machining of Ti-6Al-4V through EDM using Copper Tungsten Electrode and Positive Polarity

Year: 2010 Volume: 4 Issue: 11 1213 - 1218 Pages

Abstract: This paper deals optimized model to investigate the effects of peak current, pulse on time and pulse off time in EDM performance on material removal rate of titanium alloy utilizing copper tungsten as electrode and positive polarity of the electrode. The experiments are carried out on Ti6Al4V. Experiments were conducted by varying the peak current, pulse on time and pulse off time. A mathematical model is developed to correlate the influences of these variables and material removal rate of workpiece. Design of experiments (DOE) method and response surface methodology (RSM) techniques are implemented. The validity test of the fit and adequacy of the proposed models has been carried out through analysis of variance (ANOVA). The obtained results evidence that as the material removal rate increases as peak current and pulse on time increases. The effect of pulse off time on MRR changes with peak ampere. The optimum machining conditions in favor of material removal rate are verified and compared. The optimum machining conditions in favor of material removal rate are estimated and verified with proposed optimized results. It is observed that the developed model is within the limits of the agreeable error (about 4%) when compared to experimental results. This result leads to desirable material removal rate and economical industrial machining to optimize the input parameters.

Physical Evaluation of Selected Malaysian National Rugby Players

Year: 2011 Volume: 5 Issue: 2 158 - 162 Pages

Abstract: Currently, there is no database or local norms for the physical performance of Malaysian rugby players. This database or norms are vital for Malaysian-s sports development as programs can be setup to improve the current status. This pilot study was conducted to evaluate the status of our semi professional rugby players. The rugby players were randomly selected from the Malaysian National team and several clubs in the Klang valley, Kuala Lumpur Malaysia. 54 male rugby players (Age: 24.41 ± 4.06 years) were selected for this pilot study. Height, bodyweight, percentage body fat and body mass index (BMI) and several other physical tests were performed. Results from the BLEEP test revealed an average of level 9, shuttle 2 for the players. Interestingly, forwards were taller, heavier, and had lower maximal aerobic power than backs in the same team. In conclusion, the physical characteristics of the rugby players were much lower when compared to international players from other countries. From this pilot study, the physical performance of the Malaysian team must be improved in order to further develop the sports.

UTMGO: A Tool for Searching a Group of Semantically Related Gene Ontology Terms and Application to Annotation of Anonymous Protein Sequence

Year: 2007 Volume: 1 Issue: 3 1 - 9 Pages

Abstract: Gene Ontology terms have been actively used to annotate various protein sets. SWISS-PROT, TrEMBL, and InterPro are protein databases that are annotated according to the Gene Ontology terms. However, direct implementation of the Gene Ontology terms for annotation of anonymous protein sequences is not easy, especially for species not commonly represented in biological databases. UTMGO is developed as a tool that allows the user to quickly and easily search for a group of semantically related Gene Ontology terms. The applicability of the UTMGO is demonstrated by applying it to annotation of anonymous protein sequence. The extended UTMGO uses the Gene Ontology terms together with protein sequences associated with the terms to perform the annotation task. GOPET, GOtcha, GoFigure, and JAFA are used to compare the performance of the extended UTMGO.

Maydis stigma Improves Physical Traits and Unchanged Sensory Properties of Beef and Chicken Patties

Year: 2010 Volume: 4 Issue: 8 567 - 571 Pages

Abstract: The proximate composition, physical traits and sensory properties of beef and chicken patties incorporated with various level of dried cornsilk (Maydis stigma) were studied. The beef and chicken patties were formulated with either 2%, 4% or 6% of cornsilk. Both cooked beef and chicken patties incorporated with 6% cornsilk recorded the highest protein concentration at 23.3% and 28.42%, respectively. Both cooked beef and chicken patties containing 6% cornsilk significantly recorded the lowest concentration of fat at 11.4% and 14.60%, respectively. Beef and chicken patties formulated with 6% cornsilk recorded the highest cooking yield at 80.13% and 83.03% compared to other treatments. The inclusion of cornsilk did not change the sensory properties and consumer acceptability of cornsilk-based beef and chicken patties. Cornsilk fibre has been effective in improving cooking yield, moisture and fat retention of beef and chicken patties

Marangoni Convection in a Fluid Saturated Porous Layer with a Deformable Free Surface

Year: 2009 Volume: 3 Issue: 2 99 - 104 Pages

Abstract: The stability analysis of Marangoni convection in porous media with a deformable upper free surface is investigated. The linear stability theory and the normal mode analysis are applied and the resulting eigenvalue problem is solved exactly. The Darcy law and the Brinkman model are used to describe the flow in the porous medium heated from below. The effect of the Crispation number, Bond number and the Biot number are analyzed for the stability of the system. It is found that a decrease in the Crispation number and an increase in the Bond number delay the onset of convection in porous media. In addition, the system becomes more stable when the Biot number is increases and the Daeff number is decreases.

Artificial Intelligence Model to Predict Surface Roughness of Ti-15-3 Alloy in EDM Process

Year: 2011 Volume: 5 Issue: 2 357 - 361 Pages

Abstract: Conventionally the selection of parameters depends intensely on the operator-s experience or conservative technological data provided by the EDM equipment manufacturers that assign inconsistent machining performance. The parameter settings given by the manufacturers are only relevant with common steel grades. A single parameter change influences the process in a complex way. Hence, the present research proposes artificial neural network (ANN) models for the prediction of surface roughness on first commenced Ti-15-3 alloy in electrical discharge machining (EDM) process. The proposed models use peak current, pulse on time, pulse off time and servo voltage as input parameters. Multilayer perceptron (MLP) with three hidden layer feedforward networks are applied. An assessment is carried out with the models of distinct hidden layer. Training of the models is performed with data from an extensive series of experiments utilizing copper electrode as positive polarity. The predictions based on the above developed models have been verified with another set of experiments and are found to be in good agreement with the experimental results. Beside this they can be exercised as precious tools for the process planning for EDM.

Modeling of Pulping of Sugar Maple Using Advanced Neural Network Learning

Year: 2007 Volume: 1 Issue: 1 43 - 46 Pages

Abstract: This paper reports work done to improve the modeling of complex processes when only small experimental data sets are available. Neural networks are used to capture the nonlinear underlying phenomena contained in the data set and to partly eliminate the burden of having to specify completely the structure of the model. Two different types of neural networks were used for the application of Pulping of Sugar Maple problem. A three layer feed forward neural networks, using the Preconditioned Conjugate Gradient (PCG) methods were used in this investigation. Preconditioning is a method to improve convergence by lowering the condition number and increasing the eigenvalues clustering. The idea is to solve the modified problem where M is a positive-definite preconditioner that is closely related to A. We mainly focused on Preconditioned Conjugate Gradient- based training methods which originated from optimization theory, namely Preconditioned Conjugate Gradient with Fletcher-Reeves Update (PCGF), Preconditioned Conjugate Gradient with Polak-Ribiere Update (PCGP) and Preconditioned Conjugate Gradient with Powell-Beale Restarts (PCGB). The behavior of the PCG methods in the simulations proved to be robust against phenomenon such as oscillations due to large step size.

Demulsification of Water-in-Oil Emulsions by Microwave Heating Technology

Year: 2010 Volume: 4 Issue: 2 166 - 171 Pages

Abstract: The mechanism of microwave heating is essentially that of dielectric heating. After exposing the emulsion to the microwave Electromagnetic (EM) field, molecular rotation and ionic conduction due to the penetration of (EM) into the emulsion are responsible for the internal heating. To determine the capability of microwave technology in demulsification of crude oil emulsions, microwave demulsification method was applied in a 50-50 % and 20- 80 % water-in-oil emulsions with microwave exposure time varied from 20-180 sec. Transient temperature profiles of water-in-oil emulsions inside a cylindrical container were measured. The temperature rise at a given location was almost horizontal (linear). The average rates of temperature increase of 50-50 % and 20-80 % water-in-oil emulsions are 0.351 and 0.437 oC/sec, respectively. The rate of temperature increase of emulsions decreased at higher temperature due to decreasing dielectric loss of water. These results indicate that microwave demulsification of water-in-oil emulsions does not require chemical additions. Microwave has the potential to be used as an alternative way in the demulsification process.

Histopathological and Morphological Defects in the Mice Prenatally Exposed to Low EMF

Year: 2010 Volume: 4 Issue: 1 16 - 19 Pages

Abstract: This research was carried out to determine the possible effects of low electromagnetic field (EMF) exposure to the developing mice fetuses. Pregnant mice were exposed to EMF exposure at 0mT (sham) and 1.2 mT for six hours per session, carried out on gestation day 3, 6, 9, 12 and 15. Samples from the stillborn offspring were observed for morphological defects. The heart didn-t show progressive cellular damage, the lungs were congested and emphysemics. The bones were in advance stage of hypertrophy. Spectrums of morphological defects were observed over 70% of the surviving offspring. These results indicate that even at lower exposure to low EMF, is enough to induce morphological defects in prenatal mice.

Authenticity Issues of Social Media: Credibility, Quality and Reality

Year: 2013 Volume: 7 Issue: 2 338 - 345 Pages

Abstract: Social media has led to paradigm shifts in ways people work and do business, interact and socialize, learn and obtain knowledge. So much so that social media has established itself as an important spatial extension of this nation-s historicity and challenges. Regardless of the enabling reputation and recommendation features through social networks embedded in the social media system, the overflow of broadcasted and publicized media contents turns the table around from engendering trust to doubting the trust system. When the trust is at doubt, the effects include deactivation of accounts and creation of multiple profiles, which lead to the overflow of 'ghost' contents (i.e. “the abundance of abandoned ships"). In most literature, the study of trust can be related to culture; hence the difference between Western-s “openness" and Eastern-s “blue-chip" concepts in networking and relationships. From a survey on issues and challenges among Malaysian social media users, 'authenticity' emerges as one of the main factors that causes and is caused by other factors. The other issue that has surfaced is credibility either in terms of message/content and source. Another is the quality of the knowledge that is shared. This paper explores the terrains of this critical space which in recent years has been dominated increasingly by, arguably, social networks embedded in the social media system, the overflow of broadcasted and publicized media content.

Top Journal

SUGGEST A JOURNAL