Abstract: A 15-storey RC building, studied in this paper, is
representative of modern building type constructed in Madina City in
Saudi Arabia before 10 years ago. These buildings are almost
consisting of reinforced concrete skeleton i.e. columns, beams and
flat slab as well as shear walls in the stairs and elevator areas
arranged in the way to have a resistance system for lateral loads
(wind – earthquake loads). In this study, the dynamic properties of
the 15-storey RC building were identified using ambient motions
recorded at several, spatially-distributed locations within each
building. Three dimensional pushover analysis (Nonlinear static
analysis) was carried out using SAP2000 software incorporating
inelastic material properties for concrete, infill and steel. The effect
of modeling the building with and without infill walls, on the
performance point as well as capacity and demand spectra due to EQ
design spectrum function in Madina area has been investigated. ATC-
40 capacity and demand spectra are utilized to get the modification
factor (R) for the studied building. The purpose of this analysis is to
evaluate the expected performance of structural systems by
estimating, strength and deformation demands in design, and
comparing these demands to available capacities at the performance
levels of interest. The results are summarized and discussed.
Abstract: Creativity is marked by the ability or power, to
produce through imaginative skill and create something anew. The
University is one of the great places to improve the talent in
imaginative skill. The purpose of this study was to identify a
creativity of the student in presentation product development. Two
hundred seventeen Technical and Vocational Education (TVE)
students in Universiti Tun Hussein Onn had chosen as a respondent.
This study is to survey the level of creativity which is focused on
knowledge, skills, presentation style, and character of creative
personnel. The level of creativity was measured based on the scale at
low, medium and high followed by mean score level. The data
collected by questionnaire, then analyzed using SPSS version
20.0.The result of the study indicated that the students showed a
higher of creativity (mean score in Knowledge = 4.12 and Skills=
4.02). In conjunction with the findings, implications and
recommendations were suggested forward like to ensconce the
research and improve with a more creativity concept in presentation
product of development for learning and teaching process.
Abstract: Orthogonal Frequency Division Multiplexing
(OFDM) has been used in many advanced wireless communication
systems due to its high spectral efficiency and robustness to
frequency selective fading channels. However, the major concern
with OFDM system is the high peak-to-average power ratio (PAPR)
of the transmitted signal. Some of the popular techniques used for
PAPR reduction in OFDM system are conventional partial transmit
sequences (CPTS) and clipping. In this paper, a parallel
combination/hybrid scheme of PAPR reduction using clipping and
CPTS algorithms is proposed. The proposed method intelligently
applies both the algorithms in order to reduce both PAPR as well as
computational complexity. The proposed scheme slightly degrades
bit error rate (BER) performance due to clipping operation and it can
be reduced by selecting an appropriate value of the clipping ratio
(CR). The simulation results show that the proposed algorithm
achieves significant PAPR reduction with much reduced
computational complexity.
Abstract: With the increasing number of people reviewing
products online in recent years, opinion sharing websites has become
the most important source of customers’ opinions. Unfortunately,
spammers generate and post fake reviews in order to promote or
demote brands and mislead potential customers. These are notably
destructive not only for potential customers, but also for business
holders and manufacturers. However, research in this area is not
adequate, and many critical problems related to spam detection have
not been solved to date. To provide green researchers in the domain
with a great aid, in this paper, we have attempted to create a highquality
framework to make a clear vision on review spam-detection
methods. In addition, this report contains a comprehensive collection
of detection metrics used in proposed spam-detection approaches.
These metrics are extremely applicable for developing novel
detection methods.
Abstract: The beginning of 21st century has witnessed new
advancements in the design and use of new materials for biosensing
applications, from nano to macro, protein to tissue. Traditional
analytical methods lack a complete toolset to describe the
complexities introduced by living systems, pathological relations,
discrete hierarchical materials, cross-phase interactions, and
structure-property dependencies. Materiomics – via systematic
molecular dynamics (MD) simulation – can provide structureprocess-
property relations by using a materials science approach
linking mechanisms across scales and enables oriented biosensor
design. With this approach, DNA biosensors can be utilized to detect
disease biomarkers present in individuals’ breath such as acetone for
diabetes. Our wireless sensor array based on single-stranded DNA
(ssDNA)-decorated single-walled carbon nanotubes (SWNT) has
successfully detected trace amount of various chemicals in vapor
differentiated by pattern recognition. Here, we present how MD
simulation can revolutionize the way of design and screening of DNA
aptamers for targeting biomarkers related to oral diseases and oral
health monitoring. It demonstrates great potential to be utilized to
build a library of DNDA sequences for reliable detection of several
biomarkers of one specific disease, and as well provides a new
methodology of creating, designing, and applying of biosensors.
Abstract: An Energetic and exergetic analysis is conducted on a
Steam Turbine Power Plant of an existing Phosphoric Acid Factory.
The heat recovery systems used in different parts of the plant are also
considered in the analysis. Mass, thermal and exergy balances are
established on the main compounds of the factory. A numerical code
is established using EES software to perform the calculations
required for the thermal and exergy plant analysis. The effects of the
key operating parameters such as steam pressure and temperature,
mass flow rate as well as seawater temperature, on the cycle
performances are investigated. A maximum Exergy Loss Rate of about 72% is obtained for the
melters, followed by the condensers, heat exchangers and the pumps.
The heat exchangers used in the phosphoric acid unit present
exergetic efficiencies around 33% while 60% to 72% are obtained for
steam turbines and blower. For the explored ranges of HP steam
temperature and pressure, the exergy efficiencies of steam turbine
generators STGI and STGII increase of about 2.5% and 5.4%
respectively. In the same way optimum HP steam flow rate values,
leading to the maximum exergy efficiencies are defined.
Abstract: Ambient Computing or Ambient Intelligence (AmI) is
emerging area in computer science aiming to create intelligently
connected environments and Internet of Things. In this paper, we
propose communication middleware architecture for AmI. This
middleware architecture addresses problems of communication,
networking, and abstraction of applications, although there are other
aspects (e.g. HCI and Security) within general AmI framework.
Within this middleware architecture, any application developer might
address HCI and Security issues with extensibility features of this
platform.
Abstract: Teaching of mathematics to engineering students is an
open ended problem in education. The main goal of mathematics
learning for engineering students is the ability of applying a wide
range of mathematical techniques and skills in their engineering
classes and later in their professional work. Most of the
undergraduate engineering students and faculties feels that no efforts
and attempts are made to demonstrate the applicability of various
topics of mathematics that are taught thus making mathematics
unavoidable for some engineering faculty and their students. The lack
of understanding of concepts in engineering mathematics may hinder
the understanding of other concepts or even subjects. However, for
most undergraduate engineering students, mathematics is one of the
most difficult courses in their field of study. Most of the engineering students never understood mathematics or
they never liked it because it was too abstract for them and they could
never relate to it. A right balance of application and concept based
teaching can only fulfill the objectives of teaching mathematics to
engineering students. It will surely improve and enhance their
problem solving and creative thinking skills. In this paper, some practical (informal) ways of making
mathematics-teaching application based for the engineering students
is discussed. An attempt is made to understand the present state of
teaching mathematics in engineering colleges. The weaknesses and
strengths of the current teaching approach are elaborated. Some of
the causes of unpopularity of mathematics subject are analyzed and a
few pragmatic suggestions have been made. Faculty in mathematics
courses should spend more time discussing the applications as well as
the conceptual underpinnings rather than focus solely on strategies
and techniques to solve problems. They should also introduce more
‘word’ problems as these problems are commonly encountered in
engineering courses. Overspecialization in engineering education
should not occur at the expense of (or by diluting) mathematics and
basic sciences. The role of engineering education is to provide the
fundamental (basic) knowledge and to teach the students simple
methodology of self-learning and self-development. All these issues
would be better addressed if mathematics and engineering faculty
join hands together to plan and design the learning experiences for
the students who take their classes. When faculties stop competing
against each other and start competing against the situation, they will
perform better. Without creating any administrative hassles these
suggestions can be used by any young inexperienced faculty of
mathematics to inspire engineering students to learn engineering
mathematics effectively.
Abstract: Concrete is an essential building material which is
widely used in construction industry all over the world due to its
compressible strength. Curing of concrete plays a vital role in
durability and other performance necessities. Improper curing can
affect the concrete performance and durability easily. When areas
like scarcity of water, structures is not accessible by humans external
curing cannot be performed, so we opt for internal curing. Internal
curing (or) self curing plays a major role in developing the concrete
pore structure and microstructure. The concept of internal curing is to
enhance the hydration process to maintain the temperature uniformly.
The evaporation of water in the concrete is reduced by self curing
agent (Super Absorbing Polymer – SAP) there by increasing the
water retention capacity of the concrete. The research work was
carried out to reduce water, which is prime material used for concrete
in the construction industry. Concrete curing plays a major role in
developing hydration process. Concept of self curing will reduce the
evaporation of water from concrete. Self curing will increase water
retention capacity as compared to the conventional concrete. Proper
self curing (or) internal curing increases the strength, durability and
performance of concrete. Super absorbing Polymer (SAP) used as
internal curing agent. In this study 0.2% to 0.4% of SAP was varied
in different grade of high strength concrete. In the experiment
replacement of cement by silica fumes with 5%, 10% and 15% are
studied. It is found that replacement of silica fumes by 10 % gives
more strength and durability when compared to others.
Abstract: In this current contribution, authors are dedicated to
investigate influence of the crystal lamellae orientation on
electromechanical behaviors of relaxor ferroelectric Poly
(vinylidene fluoride –trifluoroethylene -chlorotrifluoroethylene)
(P(VDF-TrFE-CTFE)) films by control of polymer microstructure,
aiming to picture the full map of structure-property relationship. In
order to define their crystal orientation films, terpolymer films were
fabricated by solution-casting, stretching and hot-pressing process.
Differential scanning calorimetry, impedance analyzer, and tensile
strength techniques were employed to characterize crystallographic
parameters, dielectric permittivity, and elastic Young’s modulus
respectively. In addition, large electrical induced out-of-plane
electrostrictive strain was obtained by cantilever beam mode.
Consequently, as-casted pristine films exhibited surprisingly high
electrostrictive strain 0.1774% due to considerably small value of
elastic Young’s modulus although relatively low dielectric
permittivity. Such reasons contributed to large mechanical elastic
energy density. Instead, due to 2 folds increase of elastic Young’s
modulus and less than 50% augmentation of dielectric constant, fullycrystallized
film showed weak electrostrictive behavior and
mechanical energy density as well. And subjected to mechanical
stretching process, Film C exhibited stronger dielectric constant and
out-performed electrostrictive strain over Film B because edge-on
crystal lamellae orientation induced by uniaxially mechanical stretch.
Hot-press films were compared in term of cooling rate. Rather large
electrostrictive strain of 0.2788% for hot-pressed Film D in
quenching process was observed although its dielectric permittivity
equivalent to that of pristine as-casted Film A, showing highest
mechanical elastic energy density value of 359.5 J/m3. In hot-press
cooling process, dielectric permittivity of Film E saw values at 48.8
concomitant with ca.100% increase of Young’s modulus. Films with
intermediate mechanical energy density were obtained.
Abstract: Visibility problems are central to many computational geometry applications. One of the typical visibility problems is computing the view from a given point. In this paper, a linear time procedure is proposed to compute the visibility subsets from a corner of a rectangular prism in an orthogonal polyhedron. The proposed algorithm could be useful to solve classic 3D problems.
Abstract: The construction of most coastal infrastructure developments around the world are usually made considering wave height, current velocities and river discharges; however, little effort has been paid to surveying sediment transport during dredging or the modification to currents outside the ports or marinas during and after the construction. This study shows a complete survey during the construction of one of the largest ports of the Gulf of Mexico. An anchored Acoustic Doppler Current Velocity profiler (ADCP), a towed ADCP and a combination of model outputs were used at the Veracruz port construction in order to describe the hourly sediment transport and current modifications in and out of the new port. Owing to the stability of the system the new port was construction inside Vergara Bay, a low wave energy system with a tidal range of up to 0.40 m. The results show a two-current system pattern within the bay. The north side of the bay has an anticyclonic gyre, while the southern part of the bay shows a cyclonic gyre. Sediment transport trajectories were made every hour using the anchored ADCP, a numerical model and the weekly data obtained from the towed ADCP within the entire bay. The sediment transport trajectories were carefully tracked since the bay is surrounded by coral reef structures which are sensitive to sedimentation rate and water turbidity. The survey shows that during dredging and rock input used to build the wave breaker sediments were locally added (< 2500 m2) and local currents disperse it in less than 4 h. While the river input located in the middle of the bay and the sewer system plant may add more than 10 times this amount during a rainy day or during the tourist season. Finally, the coastal line obtained seasonally with a drone suggests that the southern part of the bay has not been modified by the construction of the new port located in the northern part of the bay, owing to the two subsystem division of the bay.
Abstract: Excessive vibration means increased wear, increased
repair efforts, bad product selection & quality and high energy
consumption. This may be sometimes experienced by cavitation or
suction/discharge recirculation which could occur only when net
positive suction head available NPSHA drops below the net positive
suction head required NPSHR. Cavitation can cause axial surging, if it
is excessive, will damage mechanical seals, bearings, possibly other
pump components frequently, and shorten the life of the impeller.
Efforts have been made to explain Suction Energy (SE), Specific
Speed (Ns), Suction Specific Speed (Nss), NPSHA, NPSHR & their
significance, possible reasons of cavitation /internal recirculation, its
diagnostics and remedial measures to arrest and prevent cavitation in
this paper. A case study is presented by the author highlighting that
the root cause of unwanted noise and vibration is due to cavitation,
caused by high specific speeds or inadequate net- positive suction
head available which results in damages to material surfaces of
impeller & suction bells and degradation of machine performance, its
capacity and efficiency too. Author strongly recommends revisiting
the technical specifications of CW pumps to provide sufficient NPSH
margin ratios >1.5, for future projects and Nss be limited to 8500 -
9000 for cavitation free operation.
Abstract: The most crucial aspect that is closely related to vocabulary and the one that needs to be emphasized and investigated more than it has been up until now, is the ability to combine words that co-occur frequently in the language. Pedagogically, collocation is one of the error-provoking aspects in foreign language learning. This is indicative of the dire need to provide L2 learners with tools to help them improve their collocational knowledge. This paper pinpoints the role that collocations play in the English language. Furthermore, it presents pedagogical implications for ESL/EFL learners.
Abstract: The simulation in wind tunnel is used thoroughly to model real situations of drainages of air. Besides the automotive industry, a great number of applications can be numbered: dispersion of pollutant, studies of pedestrians’ comfort, and dispersion of particles. This work had the objective of visualizing the characteristics aerodynamics of two automobiles in different ways. To accomplish that drainage of air a fan that generated a speed exists (measured with anemometer of hot thread) of 4,1m/s and 4,95m/s. To visualize the path of the air through the cars, in the wind tunnel, smoke was used, obtained with it burns of vegetable oil. For “to do smoke” vegetable oil was used, that was burned for a tension of 20V generated by a thread of 2,5mm. The cars were placed inside of the wind tunnel with the drainage of “air-smoke” and photographed, registering like this the path lines around them, in the 3 different speeds.
Abstract: A combined heat and power (CHP) system is an efficient and clean way to generate power (electricity). Heat produced by the CHP system can be used for water and space heating. The CHP system which uses hydrogen as fuel produces zero carbon emission. Its’ efficiency can reach more than 80% whereas that of a traditional power station can only reach up to 50% because much of the thermal energy is wasted. The other advantages of CHP systems include that they can decentralize energy generation, improve energy security and sustainability, and significantly reduce the energy cost to the users. This paper presents the economic benefits of using a CHP system in the domestic environment. For this analysis, natural gas is considered as potential fuel as the hydrogen fuel cell based CHP systems are rarely used. UK government incentives for CHP systems are also considered as the added benefit. Results show that CHP requires a significant initial investment in returns it can reduce the annual energy bill significantly. Results show that an investment may be paid back in 7 years. After the back period, CHP can run for about 3 years as most of the CHP manufacturers provide 10 year warranty.
Abstract: The paper presents an additive manufacturing process for the production of metal and composite parts. It is termed as composite metal foil manufacturing and is a combination of laminated object manufacturing and brazing techniques. The process has been described in detail and is being used to produce dissimilar aluminum to copper foil single lap joints. A three dimensional finite element model has been developed to study the thermo-mechanical characteristics of the dissimilar Al/Cu single lap joint. The effects of thermal stress and strain have been analyzed by carrying out transient thermal analysis on the heated plates used to join the two 0.1mm thin metal foils. Tensile test has been carried out on the foils before joining and after the single Al/Cu lap joints are made, they are subjected to tensile lap-shear test to analyze the effect of heat on the foils. The analyses are designed to assess the mechanical integrity of the foils after the brazing process and understand whether or not the heat treatment has an effect on the fracture modes of the produced specimens.
Abstract: Electro-osmosis in clayey soils and sediments, for
purposes of clay consolidation, dewatering, or cleanup, and electro
injection in porous media is widespread recent decades. It is
experimentally found that the chemical properties of porous media
especially PH change the characteristics of media. Electro-osmotic
conductivity is a function of soil and grout material chemistry,
altering with time. Many numerical approaches exist to simulate the
of electro kinetic flow rate considering chemical changes. This paper
presents a simplified analytical solution for constant flow rate based
on varying electro osmotic conductivity and time dependent viscosity
for injection of colloidal silica.
Abstract: Nanotechnology in pristine sense refers to building of
structures at atomic and molecular scale. Meticulously
nanotechnology encompasses the nanomaterials with at least one
dimension size ranging from 1 to 100 nanometres. Unlike the literal
meaning of its name, nanotechnology is a massive concept beyond
imagination. This paper predominantly deals with relevance of
nanotechnology in automotive industries. New generation of
automotives looks at nanotechnology as an emerging trend of
manufacturing revolution. Intricate shapes can be made out of fairly
inexpensive raw materials instead of conventional fabrication
process. Though the current era have enough technology to face
competition, nanotechnology can give futuristic implications to pick
up the modern pace. Nanotechnology intends to bridge the gap
between automotives with superior technical performance and their
cost fluctuation. Preliminarily, it is an area of great scientific interest
and a major shaper of many new technologies. Nanotechnology can
be an ideal building block for automotive industries, under constant
evolution offering a very wide scope of activity. It possesses huge
potential and is still in the embryonic form of research and
development.
Abstract: In order to study the Mutual effect of genotype ×
environment for the percent of oil index in sunflower items, an
experiment was accomplished form complete random block designs
in four iteration and was four diverse researching station comprising
Esfahan, Birjand, Sari, and Karaj. Complex variance analysis showed
that there is an important diversity between the items under
investigation. The results relevant the coefficient variation of items
Azargol and Vidoc has respectively allocated the minimum
coefficient of variations. According to the results extrapolated from
Shokla stability variance, the Items Brocar, Allison and Fabiola, are
among the stable genotypes for oil percent respectively. In the biplot
GGE, the location under investigations divided in two superenvironments,
first one comprised of locations naming Esfahan,
Karaj, and Birjand, and second one were such a location as Sari. By
this point of view, in the first super-environment, the Item Fabiola
and in the second Almanzor item was among the best items and
crops.