Abstract: The theatre-auditorium under investigation following
the highly reflective characteristics of materials used in it (marble,
painted wood, smooth plaster, etc), architectural and structural
features of the Protocol and its intended use (very multifunctional:
Auditorium, theatre, cinema, musicals, conference room) from the
analysis of the statement of fact made by the acoustic simulation
software Ramsete and supported by data obtained through a
campaign of acoustic measurements of the state of fact made on the
spot by a Fonomet Svantek model SVAN 957, appears to be
acoustically inadequate. After the completion of the 3D model
according to the specifications necessary software used forecast in
order to be recognized by him, have made three simulations, acoustic
simulation of the state of and acoustic simulation of two design
solutions.
Improved noise characteristics found in the first design solution,
compared to the state in fact consists therefore in lowering
Reverberation Time that you turn most desirable value, while the
Indicators of Clarity, the Baricentric Time, the Lateral Efficiency,
Ratio of Low Tmedia BR and defined the Speech Intelligibility
improved significantly. Improved noise characteristics found instead
in the second design solution, as compared to first design solution, is
finally mostly in a more uniform distribution of Leq and in lowering
Reverberation Time that you turn the optimum values. Indicators of
Clarity, and the Lateral Efficiency improve further but at the expense
of a value slightly worse than the BR. Slightly vary the remaining
indices.
Abstract: In order to answer the general question: “What does a simple agent with a limited life-time require for constructing a useful representation of the environment?" we propose a robot platform including the simplest probabilistic sensory and motor layers. Then we use the platform as a test-bed for evaluation of the navigational capabilities of the robot with different “brains". We claim that a protocognitive behavior is not a consequence of highly sophisticated sensory–motor organs but instead emerges through an increment of the internal complexity and reutilization of the minimal sensory information. We show that the most fundamental robot element, the short-time memory, is essential in obstacle avoidance. However, in the simplest conditions of no obstacles the straightforward memoryless robot is usually superior. We also demonstrate how a low level action planning, involving essentially nonlinear dynamics, provides a considerable gain to the robot performance dynamically changing the robot strategy. Still, however, for very short life time the brainless robot is superior. Accordingly we suggest that small organisms (or agents) with short life-time does not require complex brains and even can benefit from simple brain-like (reflex) structures. To some extend this may mean that controlling blocks of modern robots are too complicated comparative to their life-time and mechanical abilities.
Abstract: Performance of vehicle depends on driving patterns
and vehicle drive train configuration. Driving patterns depends on
traffic condition, road condition and driver behavior. HEV design is
carried out under certain constrain like vehicle operating range,
acceleration, decelerations, maximum speed and road grades which
are directly related to the driving patterns. Therefore the detailed
study on HEV performance over a different drive cycle is required
for selection and sizing of HEV components. A simple hardware is
design to measured velocity v/s time profile of the vehicle by
operating vehicle on Indian roads under real traffic conditions. To
size the HEV components, a detailed dynamic model of the vehicle is
developed considering the effect of inertia of rotating components
like wheels, drive chain, engine and electric motor. Using vehicle
model and different Indian drive cycles data, total tractive power
demanded by vehicle and power supplied by individual components
has been calculated.Using above information selection and estimation
of component sizing for HEV is carried out so that HEV performs
efficiently under hostile driving condition. Complete analysis is
carried out in LABVIEW.
Abstract: With increasing data in medical databases, medical
data retrieval is growing in popularity. Some of this analysis
including inducing propositional rules from databases using many
soft techniques, and then using these rules in an expert system.
Diagnostic rules and information on features are extracted from
clinical databases on diseases of congenital anomaly. This paper
explain the latest soft computing techniques and some of the
adaptive techniques encompasses an extensive group of methods
that have been applied in the medical domain and that are used for
the discovery of data dependencies, importance of features,
patterns in sample data, and feature space dimensionality
reduction. These approaches pave the way for new and interesting
avenues of research in medical imaging and represent an important
challenge for researchers.
Abstract: Epstein-Barr virus (EBV) is implicated in the pathogenesis of the endemic Burkitt-s lymphoma (BL). The EBVpositive BL-derived cell lines initially maintain the original tumor phenotype of EBV infection (latency I, LatI), but most of them drift toward a lymphoblast phenotype of EBV latency III (LatIII) during in vitro culturing. The aim of the present work was to characterize the B-cell subsets in EBV-positive BL cell lines and to verify whether a particular cell subset correlates with the type of EBV infection. The phenotype analysis of two EBV-negative and eleven EBV-positive (three of LatI and eight of LatIII) BL cell lines was performed by polychromatic flow cytomery, based on expression pattern of CD19, CD10, CD38, CD27, and CD5 markers. Two cell subsets, CD19+CD10+ and CD19+CD10-, were defined in LatIII BL cell lines. In both subsets, the CD27 and CD5 cell surface expression was detected in a proportion of the cells.
Abstract: Voltage stability has become an important issue to many power systems around the world due to the weak systems and long line on power system networks. In this paper, MATLAB load flow program is applied to obtain the weak points in the system combined with finding the voltage stability limit. The maximum permissible loading of a system, within the voltage stability limit, is usually determined. The methods for varying tap ratio (using tap changing transformer) and applying different values of shunt capacitor injection to improve the voltage stability within the limit are also provided.
Abstract: In this work, effects of catalysts (TiO2, and Nb2O5) were investigated on the hydrogen desorption of Mg(BH4)2. LiBH4 and MgCl2 with 2:1 molar ratio were mixed by using ball milling to prepare Mg(BH4)2. The desorption behaviors were measured by thermo-volumetric apparatus. The hydrogen desorption capacity of the mixed sample milled for 2 h was 4.78 wt% with a 2-step released. The first step occurred at 214 °C and the second step appeared at 374 °C. The addition of 16 wt% Nb2O5 decreased the desorption temperature in the second step about 66 °C and increased the hydrogen desorption capacity to 4.86 wt% hydrogen. The addition of TiO2 also improved the desorption temperature in the second step and the hydrogen desorption capacity. It decreased the desorption temperature about 71°C and showed a high amount of hydrogen, 5.27 wt%, released from the mixed sample. The hydrogen absorption after desorption of Mg(BH4)2 was also studied under 9.5 MPa and 350 °C for 12 h.
Abstract: A set of Artificial Neural Network (ANN) based methods
for the design of an effective system of speech recognition of
numerals of Assamese language captured under varied recording
conditions and moods is presented here. The work is related to
the formulation of several ANN models configured to use Linear
Predictive Code (LPC), Principal Component Analysis (PCA) and
other features to tackle mood and gender variations uttering numbers
as part of an Automatic Speech Recognition (ASR) system in
Assamese. The ANN models are designed using a combination of
Self Organizing Map (SOM) and Multi Layer Perceptron (MLP)
constituting a Learning Vector Quantization (LVQ) block trained in a
cooperative environment to handle male and female speech samples
of numerals of Assamese- a language spoken by a sizable population
in the North-Eastern part of India. The work provides a comparative
evaluation of several such combinations while subjected to handle
speech samples with gender based differences captured by a microphone
in four different conditions viz. noiseless, noise mixed, stressed
and stress-free.
Abstract: Process planning and production scheduling play
important roles in manufacturing systems. In this paper a multiobjective
mixed integer linear programming model is presented for
the integrated planning and scheduling of multi-product. The aim is
to find a set of high-quality trade-off solutions. This is a
combinatorial optimization problem with substantially large solution
space, suggesting that it is highly difficult to find the best solutions
with the exact search method. To account for it, a PSO-based
algorithm is proposed by fully utilizing the capability of the
exploration search and fast convergence. To fit the continuous PSO
in the discrete modeled problem, a solution representation is used in
the algorithm. The numerical experiments have been performed to
demonstrate the effectiveness of the proposed algorithm.
Abstract: Airbag deployment has been known to be responsible
for huge death, incidental injuries and broken bones due to low crash
severity and wrong deployment decisions. Therefore, the authorities
and industries have been looking for more innovative and intelligent
products to be realized for future enhancements in the vehicle safety
systems (VSSs). Although the VSSs technologies have advanced
considerably, they still face challenges such as how to avoid
unnecessary and untimely airbag deployments that can be hazardous
and fatal. Currently, most of the existing airbag systems deploy
without regard to occupant size and position. As such, this paper will
focus on the occupant and crash sensing performances due to frontal
collisions for the new breed of so called smart airbag systems. It
intends to provide a thorough discussion relating to the occupancy
detection, occupant size classification, occupant off-position
detection to determine safe distance zone for airbag deployment,
crash-severity analysis and airbag decision algorithms via a computer
modeling. The proposed system model consists of three main
modules namely, occupant sensing, crash severity analysis and
decision fusion. The occupant sensing system module utilizes the
weight sensor to determine occupancy, classify the occupant size,
and determine occupant off-position condition to compute safe
distance for airbag deployment. The crash severity analysis module is
used to generate relevant information pertinent to airbag deployment
decision. Outputs from these two modules are fused to the decision
module for correct and efficient airbag deployment action. Computer
modeling work is carried out using Simulink, Stateflow,
SimMechanics and Virtual Reality toolboxes.
Abstract: The purpose of this research was to study the
influence of learning efficiency on local accountants’ job
performance effectiveness. This paper drew upon the survey data
collected from 335 local accountants survey conducted at Nakhon
Ratchasima province, Thailand. The statistics utilized in this paper
included percentage, mean, standard deviation, and regression
analysis. The findings revealed that the majority of samples were
between 31-40 years old, married, held an undergraduate degree, and
had an average income between 10,000-15,000 baht. The majority of
respondents had less than five years of accounting experience and
worked for local administrations. The overall learning efficiency
score was in the highest level while the local accountants’ job
performance effectiveness score was also in the high level. The
hypothesis testing’s result disclosed that learning efficiency factors
which were knowledge, Skill, and Attitude had an influence on local
accountants’ job the performance effectiveness.
Abstract: The increments of aromatic structures are widely used to monitor the degree of humification. Compost derived from mix manures mixed with agricultural wastes was studied. The compost collected at day 0, 7, 14, 21, 28, 35, 49, 77, 91, 105, and 119 was divided into 3 stages, initial stage at day 0, thermophilic stage during day 1-48, and mature stage during day 49-119. The change of highest absorptions at wavelength range between 210-235 nm during day 0- 49 implied that small molecules such as nitrates and carboxylic occurred faster than the aromatic molecules that were found at wavelength around 280 nm. The ratio of electron-transfer band at wavelength 253 nm by the benzonoid band at wavelength 230 nm (E253/E230) also gradually increased during the fermenting period indicating the presence of O-containing functional groups. This was in agreement with the shift change from aliphatic to aromatic structures as shown by the relationship with C/N and H/C ratios (r = - 0.631 and -0.717, p< 0.05) since both were decreasing. Although the amounts of humic acid (HA) were not different much during the humification process, the UV spectral deconvolution showed better qualitative characteristics to help in determining the compost quality. From this study, the compost should be used at day 49 and should not be kept longer than 3 months otherwise the quality of HA would decline regardless of the amounts of HA that might be rising. This implied that other processes, such as mineralization had an influence on the humification process changing HA-s structure and its qualities.
Abstract: The paper describes a self supervised parallel self organizing neural network (PSONN) architecture for true color image segmentation. The proposed architecture is a parallel extension of the standard single self organizing neural network architecture (SONN) and comprises an input (source) layer of image information, three single self organizing neural network architectures for segmentation of the different primary color components in a color image scene and one final output (sink) layer for fusion of the segmented color component images. Responses to the different shades of color components are induced in each of the three single network architectures (meant for component level processing) by applying a multilevel version of the characteristic activation function, which maps the input color information into different shades of color components, thereby yielding a processed component color image segmented on the basis of the different shades of component colors. The number of target classes in the segmented image corresponds to the number of levels in the multilevel activation function. Since the multilevel version of the activation function exhibits several subnormal responses to the input color image scene information, the system errors of the three component network architectures are computed from some subnormal linear index of fuzziness of the component color image scenes at the individual level. Several multilevel activation functions are employed for segmentation of the input color image scene using the proposed network architecture. Results of the application of the multilevel activation functions to the PSONN architecture are reported on three real life true color images. The results are substantiated empirically with the correlation coefficients between the segmented images and the original images.
Abstract: This paper presents the generation of bipolar square
wave pulses with characteristics that are suitable for liquid food
sterilization using a Cascaded H-bridge Multilevel Inverter (CHMI).
Bipolar square waves pulses have been reported as stable for a
longer time during the sterilization process with minimum heat
emission and increased efficiency. The CHMI allows the system to
produce bipolar square wave pulses and yielding high output voltage
without using a transformer while fulfilling the pulse requirements
for effective liquid food sterilization. This in turn can reduce power
consumption and cost of the overall liquid food sterilization system.
The simulation results have shown that pulses with peak output
voltage of 2.4 kV, pulse width of between 1 2s and 1 ms at
frequencies of 50 Hz and 100 Hz can be generated by a 7-level
CHMI. Results from the experimental set-up based on a 5-level
CHMI has indicated the potential of the proposed circuit in
producing bipolar square wave output pulses with peak values that
depends on the DC source level supplied to the CHMI modules,
pulse width of between 12.5 2s and 1 ms at frequencies of 50 Hz
and 100 Hz.
Abstract: In the hardening energy context, the transport sector
which constitutes a large worldwide energy demand has to be
improving for decrease energy demand and global warming impacts.
In a controversial situation where subsists an increasing demand for
long-distance and high-speed travels, high-speed trains offer many
advantages, as consuming significantly less energy than road or air
transports.
At the project phase of new rail infrastructures, it is nowadays
important to characterize accurately the energy that will be induced
by its operation phase, in addition to other more classical criteria as
construction costs and travel time.
Current literature consumption models used to estimate railways
operation phase are obsolete or not enough accurate for taking into
account the newest train or railways technologies.
In this paper, an updated model of consumption for high-speed is
proposed, based on experimental data obtained from full-scale tests
performed on a new high-speed line. The assessment of the model
is achieved by identifying train parameters and measured power
consumptions for more than one hundred train routes. Perspectives
are then discussed to use this updated model for accurately assess
the energy impact of future railway infrastructures.
Abstract: Recently, much research has been conducted for
security for wireless sensor networks and ubiquitous computing.
Security issues such as authentication and data integrity are major
requirements to construct sensor network systems. Advanced
Encryption Standard (AES) is considered as one of candidate
algorithms for data encryption in wireless sensor networks. In this
paper, we will present the hardware architecture to implement low
power AES crypto module. Our low power AES crypto module has
optimized architecture of data encryption unit and key schedule unit
which could be applicable to wireless sensor networks. We also details
low power design methods used to design our low power AES crypto
module.
Abstract: Cognitive Infocommunications (CogInfoCom) is a new
research direction which has emerged as the synergic convergence
of infocommunications and the cognitive sciences. In this paper,
we provide the definition of CogInfoCom, and propose an architectural
framework for the interaction-oriented design of CogInfoCom
systems. We provide the outlines of an application example of
the interaction-oriented architecture, and briefly discuss its main
characteristics.
Abstract: The present work deals with optimization of cascade refrigeration system using eco friendly refrigerants pair R507A and R23. R507A is azeotropic mixture composed of HFC refrigerants R125/R143a (50%/50% by wt.). R23 is a single component HFC refrigerant used as replacement to CFC refrigerant R13 in low temperature applications. These refrigerants have zero ozone depletion potential and are non-flammable. Optimization of R507AR23 cascade refrigeration system performance parameters such as minimum work required, refrigeration effect, coefficient of performance and exergetic efficiency was carried out in terms of eight operating parameters- combinations using Genetic Algorithm tool. The eight operating parameters include (1) low side evaporator temperature (2) high side condenser temperature (3) temperature difference in the cascade heat exchanger (4) low side condenser temperature (5) low side degree of subcooling (6) high side degree of subcooling (7) low side degree of superheating (8) high side degree of superheating. Results show that for minimum work system should operate at high temperature in low side evaporator, low temperature in high side condenser, low temperature difference in cascade condenser, high temperature in low side condenser and low degree of subcooling and superheating in both side. For maximum refrigeration effect system should operate at high temperature in low side evaporator, high temperature in high side condenser, high temperature difference in cascade condenser, low temperature in low side condenser and higher degree of subcooling in LT and HT side. For maximum coefficient of performance and exergetic efficiency, system should operate at high temperature in low side evaporator, low temperature in high side condenser, low temperature difference in cascade condenser, high temperature in low side condenser and higher degree of subcooling and superheating in low side of the system.
Abstract: Tuberculosis (TB) is a bacterial infectious disease caused by the obligate human pathogen, Mycobacterium tuberculosis. Multidrug-resistant tuberculosis (MDR-TB) is a global reality that threatens tuberculosis control. Resistance to antibiotic Rifampicin, occurs in 95% of cases through nucleotide substitutions in an 81-bp core region of the rpoB i.e; beta subunit of DNA dependant RNA polymerase. In this paper, we studied the Rifampicin-rpoB receptor interactions In silico. First, homology modeling was performed to obtain the three dimensional structure of Mycobacterium rpoB. Sixty analogs of Rifampicin were prepared using Marvin sketch software. Both original Rifampicin and the analogs were docked with rpoB and energy values were obtained. Out of sixty analogs, 43 analogs had lesser energy values than conventional Rifampicin and hence are predicted to have greater binding affinity to rpoB. Thus, this study offers a route for the development of Rifampicin analogs against multi drug resistant Mycobacterium rpoB.
Abstract: Surface currents play a major role in the distribution
of contaminants, the connectivity of marine populations, and can
influence the vertical and horizontal distribution of nutrients within
the water column. This paper aims to determine the effects of sea
breeze-wind patterns on the climatology of the surface currents on the
continental shelf surrounding Rottnest Island, WA Australia. The
alternating wind patterns allow for full cyclic rotations of wind
direction, permitting the interpretation of the effect of the wind on the
surface currents. It was found that the surface currents only clearly
follow the northbound Capes Current in times when the Fremantle
Doctor sets in. Surface currents react within an hour to a change of
direction of the wind, allowing southerly currents to dominate during
strong northerly sea breezes, often followed by mixed currents
dominated by eddies in the inter-lying times.