Abstract: Pressure wave velocity in a hydraulic system was
determined using piezo pressure sensors without removing fluid from
the system. The measurements were carried out in a low pressure
range (0.2 – 6 bar) and the results were compared with the results of
other studies. This method is not as accurate as measurement with
separate measurement equipment, but the fluid is in the actual
machine the whole time and the effect of air is taken into
consideration if air is present in the system. The amount of air is
estimated by calculations and comparisons between other studies.
This measurement equipment can also be installed in an existing
machine and it can be programmed so that it measures in real time.
Thus, it could be used e.g. to control dampers.
Abstract: A two-parameter fatigue model explicitly accounting for the cyclic as well as the mean stress was used to fit static and fatigue data available in literature concerning carbon fiber reinforced composite laminates subjected tension-tension fatigue. The model confirms the strength–life equal rank assumption and predicts reasonably the probability of failure under cyclic loading. The model parameters were found by best fitting procedures and required a minimum of experimental tests.
Abstract: The springs located in urban areas are the outpouring
of surface water, which can serve as water supply, effluent receptors
and important local macro-drainage elements. With unplanned
occupation, non-compliance with environmental legislation and the
importance of these water bodies, it is vital to analyze the springs
within urban areas, considering the Brazilian forest code. This paper
submits an analysis and discussion methodology proposal of
environmental compliance functions of urban springs, by means of
G.I.S. - Geographic Information System analysis - and in situ
analysis. The case study included two springs which exhibit a history
of occupation along its length, with different degrees of impact. The
proposed method is effective and easy to apply, representing a
powerful tool for analyzing the environmental conditions of springs
in urban areas.
Abstract: In this paper back-propagation artificial neural
network (BPANN) is employed to predict the limiting drawing ratio
(LDR) of the deep drawing process. To prepare a training set for
BPANN, some finite element simulations were carried out. die and
punch radius, die arc radius, friction coefficient, thickness, yield
strength of sheet and strain hardening exponent were used as the
input data and the LDR as the specified output used in the training of
neural network. As a result of the specified parameters, the program
will be able to estimate the LDR for any new given condition.
Comparing FEM and BPANN results, an acceptable correlation was
found.
Abstract: In this paper, a simple microfluidic device for monitoring algal cell behavior is proposed. An array of algal microwells is fabricated by PDMS soft-lithography using X-ray LIGA mold, placed on a glass substrate. Two layers of replicated PDMS and substrate are attached by oxygen plasma bonding, creating a microchannel for the microfluidic system. Algal cell are loaded into the microfluidic device, which provides positive charge on the bottom surface of wells. Algal cells, which are negative charged, can be attracted to the bottom of the wells via electrostatic interaction. By varying the concentration of algal cells in the loading suspension, it is possible to obtain wells with a single cell. Liquid medium for cells monitoring are flown continuously over the wells, providing nutrient and waste exchange between the well and the main flow. This device could lead to the uncovering of the quantitative biology of the algae, which is a key to effective and extensive algal utilizations in the field of biotechnology, food industry and bioenergy research and developments.
Abstract: Cross layer optimization based on utility functions has
been recently studied extensively, meanwhile, numerous types of
utility functions have been examined in the corresponding literature.
However, a major drawback is that most utility functions take a fixed
mathematical form or are based on simple combining, which can
not fully exploit available information. In this paper, we formulate a
framework of cross layer optimization based on Adaptively Weighted
Utility Functions (AWUF) for fairness balancing in OFDMA networks.
Under this framework, a two-step allocation algorithm is
provided as a sub-optimal solution, whose control parameters can be
updated in real-time to accommodate instantaneous QoS constrains.
The simulation results show that the proposed algorithm achieves
high throughput while balancing the fairness among multiple users.
Abstract: In this manuscript, we discuss the problem of determining the optimum stratification of a study (or main) variable based on the auxiliary variable that follows a uniform distribution. If the stratification of survey variable is made using the auxiliary variable it may lead to substantial gains in precision of the estimates. This problem is formulated as a Nonlinear Programming Problem (NLPP), which turn out to multistage decision problem and is solved using dynamic programming technique.
Abstract: Gas flaring is one of the most GHG emitting sources in the oil and gas industries. It is also a major way for wasting such an energy that could be better utilized and even generates revenue. Minimize flaring is an effective approach for reducing GHG emissions and also conserving energy in flaring systems. Integrating waste and flared gases into the fuel gas networks (FGN) of refineries is an efficient tool. A fuel gas network collects fuel gases from various source streams and mixes them in an optimal manner, and supplies them to different fuel sinks such as furnaces, boilers, turbines, etc. In this article we use fuel gas network model proposed by Hasan et al. as a base model and modify some of its features and add constraints on emission pollution by gas flaring to reduce GHG emissions as possible. Results for a refinery case study showed that integration of flare gas stream with waste and natural gas streams to construct an optimal FGN can significantly reduce total annualized cost and flaring emissions.
Abstract: There are several approaches in trying to solve the
Quantitative 1Structure-Activity Relationship (QSAR) problem.
These approaches are based either on statistical methods or on
predictive data mining. Among the statistical methods, one should
consider regression analysis, pattern recognition (such as cluster
analysis, factor analysis and principal components analysis) or partial
least squares. Predictive data mining techniques use either neural
networks, or genetic programming, or neuro-fuzzy knowledge. These
approaches have a low explanatory capability or non at all. This
paper attempts to establish a new approach in solving QSAR
problems using descriptive data mining. This way, the relationship
between the chemical properties and the activity of a substance
would be comprehensibly modeled.
Abstract: Many real-world data sets consist of a very high dimensional feature space. Most clustering techniques use the distance or similarity between objects as a measure to build clusters. But in high dimensional spaces, distances between points become relatively uniform. In such cases, density based approaches may give better results. Subspace Clustering algorithms automatically identify lower dimensional subspaces of the higher dimensional feature space in which clusters exist. In this paper, we propose a new clustering algorithm, ISC – Intelligent Subspace Clustering, which tries to overcome three major limitations of the existing state-of-art techniques. ISC determines the input parameter such as є – distance at various levels of Subspace Clustering which helps in finding meaningful clusters. The uniform parameters approach is not suitable for different kind of databases. ISC implements dynamic and adaptive determination of Meaningful clustering parameters based on hierarchical filtering approach. Third and most important feature of ISC is the ability of incremental learning and dynamic inclusion and exclusions of subspaces which lead to better cluster formation.
Abstract: The paper deals with the possibilities of modelling
vapour propagation of explosive substances in the FLUENT
software. With regard to very low tensions of explosive substance
vapours the experiment has been verified as exemplified by
mononitrotoluene. Either constant or time variable meteorological
conditions have been used for calculation. Further, it has been
verified that the eluent source may be time-dependent and may reflect
a real situation or the liberation rate may be constant. The execution
of the experiment as well as evaluation were clear and it could also
be used for modelling vapour and aerosol propagation of selected
explosive substances in the atmospheric boundary layer.
Abstract: In this paper we present our results on the performance analysis of a multi-product manufacturing line. We study the influence of external perturbations, intermediate buffer content and the number of manufacturing stages on the production tracking error of each machine in the multi-product line operated under a surplusbased production control policy. Starting by the analysis of a single machine with multiple production stages (one for each product type), we provide bounds on the production error of each stage. Then, we extend our analysis to a line of multi-stage machines, where similarly, bounds on each production tracking error for each product type, as well as buffer content are obtained. Details on performance of the closed-loop flow line model are illustrated in numerical simulations.
Abstract: This paper describes a new algorithm of arrangement
in parallel, based on Odd-Even Mergesort, called division and
concurrent mixes. The main idea of the algorithm is to achieve that
each processor uses a sequential algorithm for ordering a part of the
vector, and after that, for making the processors work in pairs in
order to mix two of these sections ordered in a greater one, also
ordered; after several iterations, the vector will be completely
ordered. The paper describes the implementation of the new
algorithm on a Message Passing environment (such as MPI). Besides,
it compares the obtained experimental results with the quicksort
sequential algorithm and with the parallel implementations (also on
MPI) of the algorithms quicksort and bitonic sort. The comparison
has been realized in an 8 processors cluster under GNU/Linux which
is running on a unique PC processor.
Abstract: This paper introduces our first efforts of developing a
new team for RoboCup Middle Size Competition. In our robots we
have applied omni directional based mobile system with omnidirectional
vision system and fuzzy control algorithm to navigate
robots. The control architecture of MRL middle-size robots is a three
layered architecture, Planning, Sequencing, and Executing. It also
uses Blackboard system to achieve coordination among agents.
Moreover, the architecture should have minimum dependency on low
level structure and have a uniform protocol to interact with real
robot.
Abstract: Low power consumption is a major constraint for battery-powered system like computer notebook or PDA. In the past, specialists usually designed both specific optimized equipments and codes to relief this concern. Doing like this could work for quite a long time, however, in this era, there is another significant restraint, the time to market. To be able to serve along the power constraint while can launch products in shorter production period, objectoriented programming (OOP) has stepped in to this field. Though everyone knows that OOP has quite much more overhead than assembly and procedural languages, development trend still heads to this new world, which contradicts with the target of low power consumption. Most of the prior power related software researches reported that OOP consumed much resource, however, as industry had to accept it due to business reasons, up to now, no papers yet had mentioned about how to choose the best OOP practice in this power limited boundary. This article is the pioneer that tries to specify and propose the optimized strategy in writing OOP software under energy concerned environment, based on quantitative real results. The language chosen for studying is C# based on .NET Framework 2.0 which is one of the trendy OOP development environments. The recommendation gotten from this research would be a good roadmap that can help developers in coding that well balances between time to market and time of battery.
Abstract: Paper deals with environmental metrics and assessment systems devoted to Small and Medium Sized Enterprises. Authors are presenting proposed assessment model which has an ability to discover current environmental strengths and weaknesses of Small and Middle Sized Enterprise. Suggested model has also an ambition to become a Sustainability Decision Tool. Model is able to identify "best environmental devision" in the company, and to quantify how this decision contributed into overall environmental improvement. Authors understand environmental improvements as environmental innovations (product, process and organizational). Suggested model is based on its own concept; however, authors are also utilizing already existing environmental assessment tools.
Abstract: This paper explores the changing trend in citizenship
norms among young citizens from various ethnic groups in Malaysia
and the extent to which it influences the participation of young
citizens in political and civil issues. Embedded in democratic
constitutions are the rights and freedoms that accompany citizenship,
and these rights and freedoms include participation. Participation in
democracies should go beyond voting; it should include taking part in
the governance process. The political process is not at risk even
though politics does not work as it did in the past. A national sample
of 1697 respondents between the ages of 21 and 40 years were
interviewed in January 2011. The findings show that respondents
embrace an engaged-citizenship norm more than they do the
traditional duty-citizen norm. Among the ethnic groups, the Chinese
show lower means in both citizenship norms compared with other
ethnic groups, namely, the Malays and the Indians. The duty-citizen
norm correlates higher with political participation than with civic
participation. On the other hand, the engaged-citizen norm correlates
higher with civic participation than with political participation.
Abstract: In order to encourage the construction of green homes
(GH) in Malaysia, a simple and attainable framework for designing
and building GHs is needed. This can be achieved by aligning GH
principles against Cole-s 'Sustainable Building Criteria' (SBC). This
set of considerations was used to categorize the GH features of three
case studies from Malaysia. Although the categorization of building
features is useful at exploring the presence of sustainability
inclinations of each house, the overall impact of building features in
each of the five SBCs are unknown. Therefore, this paper explored
the possibility of quantifying the impact of building features
categorized in SBC1 – “Buildings will have to adapt to the new
environment and restore damaged ecology while mitigating resource
use" based on existing GH assessment tools and methods and other
literature. This process as reported in this paper could lead to a new
dimension in green home rating and assessment methods.
Abstract: Restoration of endodontically treated teeth is a
common problem in dentistry, related to the fractures occurring in
such teeth and to concentration of forces little information regarding
variation of basic preparation guidelines in stress distribution has
been available. To date, there is still no agreement in the literature
about which material or technique can optimally restore
endodontically treated teeth. The aim of the present study was to
evaluate the influence of the core height and restoration materials on
corono-radicular restored upper first premolar. The first step of the
study was to achieve 3D models in order to analyze teeth, dowel and
core restorations and overlying full ceramic crowns. The FEM model
was obtained by importing the solid model into ANSYS finite
element analysis software. An occlusal load of 100 N was conducted,
and stresses occurring in the restorations, and teeth structures were
calculated. Numerical simulations provide a biomechanical
explanation for stress distribution in prosthetic restored teeth. Within
the limitations of the present study, it was found that the core height
has no important influence on the stress generated in coronoradicular
restored premolars. It can be drawn that the cervical regions
of the teeth and restorations were subjected to the highest stress
concentrations.
Abstract: Waiting times and queues are a daily problem for theme parks. Fast lines or priority queues appear as a solution for a specific segment of customers, that is, tourists who are willing to pay to avoid waiting. This paper analyzes the fast line system and explores the factors that affect the decision to purchase a fast line pass. A greater understanding of these factors may help companies to design appropriate products and services. This conceptual paper was based on a literature review in marketing and consumer behavior. Additional research was identified in related disciplines such as leisure studies, psychology, and sociology. A conceptual framework of the factors influencing the decision to purchase a fast line pass is presented.