Abstract: The bean (Phaseolus vulgaris L.) is one of the best
known of the legumes, and it has a long cultivation tradition in Italy.
The territory of “Subappennino Dauno” (southern Italy) is at around
700 m a.s.l. and is predominantly grown with cereals, olive trees and
grapevines. Ecotypes of white beans to eat dry (such as cannellini
beans) are also grown, which are sought for their palatability, high
digestibility, and ease of cooking. However, these are not easy to find
on the market due to their low production in relatively small areas
and on small family farms that use seeds handed down from
generation to generation. The introduction of these ecotypes in plain
areas of the Puglia region would provide an opportunity to promote
the diffusion of this type of bean. To investigate the adaptability of
these ecotypes in plain environments (Cerignola, in southern Italy) a
comparative trial was carried out between three ‘Monti Dauni’
ecotypes (E1, E2, E3) that are native to mountain areas and the
similar commercial variety, ‘Cannellini’. The data provide useful
information about the quantitative and qualitative characteristics of
these ecotypes when grown in lowland environments. Ecotype E3
provided the greatest bean production (2.34 t ha-1) compared to
‘Cannellini’ (1.28 t ha-1) and the other ecotypes (0.55 and 0.40 t ha-1,
for E1 and E2, respectively), due to its greater plant growth and the
larger size of the seed (and thickness, in particular). Finally, ecotype
E2 provided the greatest protein content (31.2%), although not
significantly different from the commercial cultivar ‘Cannellini’
(32.1%).
Abstract: In this study we present the effect of elevated
temperatures from 300K to 400K on the electrical properties of
copper Phthalocyanine (CuPc) based organic field effect transistors
(OFET). Thin films of organic semiconductor CuPc (40nm) and
semitransparent Al (20nm) were deposited in sequence, by vacuum
evaporation on a glass substrate with previously deposited Ag source
and drain electrodes with a gap of 40 μm. Under resistive mode of
operation, where gate was suspended it was observed that drain
current of this organic field effect transistor (OFET) show an
increase with temperature. While in grounded gate condition metal
(aluminum) – semiconductor (Copper Phthalocyanine) Schottky
junction dominated the output characteristics and device showed
switching effect from low to high conduction states like Zener diode
at higher bias voltages. This threshold voltage for switching effect
has been found to be inversely proportional to temperature and shows
an abrupt decrease after knee temperature of 360K. Change in
dynamic resistance (Rd = dV/dI) with respect to temperature was
observed to be -1%/K.
Abstract: In this note first we define the notions of intuitionistic
fuzzy dual positive implicative hyper K-ideals of types
1,2,3,4 and intuitionistic fuzzy dual hyper K-ideals. Then we
give some classifications about these notions according to the
level subsets. Also by given some examples we show that these
notions are not equivalent, however we prove some theorems
which show that there are some relationships between these
notions. Finally we define the notions of product and antiproduct
of two fuzzy subsets and then give some theorems
about the relationships between the intuitionistic fuzzy dual
positive implicative hyper K-ideal of types 1,2,3,4 and their
(anti-)products, in particular we give a main decomposition
theorem.
Abstract: In this article, the design of a Supply Chain Network
(SCN) consisting of several suppliers, production plants, distribution
centers and retailers, is considered. Demands of retailers are
considered stochastic parameters, so we generate amounts of data via
simulation to extract a few demand scenarios. Then a mixed integer
two-stage programming model is developed to optimize
simultaneously two objectives: (1) minimization the fixed and
variable cost, (2) maximization the service level. A weighting method
is utilized to solve this two objective problem and a numerical
example is made to show the performance of the model.
Abstract: Ammonia nitrogen is one of the most hazardous
water pollutants, discharging into water receptors through industrial
effluents. Negative environmental impacts of such chemical species
in hydrosphere include accelerated eutrophication, water toxicity and
harming the aquatics. Natural zeolite clinoptilolite has very high
selectivity & capacity for ammonium cation sorption. It occurs in
high abundances and rich mines of this zeolite exist in different parts
of Iran and thus are available more cheaply and with different sizing.
The aim of this study is to investigate ammonia nitrogen removal
over this natural sorbent from real samples of high polluted
wastewater discharging from a fertilizer producing plant. The
experimental results showed that this natural sorbent without even
any pre treatment system & with the same particle size available in
Iranian markets has still high capability & selectivity in ammonia
nitrogen removal both in batch and continuous tests.
Abstract: Since the admission of Islam onto the Malay World in
16th century, the Malay culture began to grow in line with the
teachings of Islam as a guide of life. Mosque become a symbol of
Muslim communities, as well as the cultural values that have been
adapted represent the maturity and readiness of Malay Muslim in
manifest a lifestyle tradition into the community. Refinement of
ornament that used to take from Hindu-Buddhist beliefs before were
adopted and refined to the Islamic values based on the teachings of
al-Quran and as-Sunnah delivered a certain message to convey a
meaning to the observer. The main purpose of this paper is to analyze
the typology and classification of ornaments in Malaysia-s traditional
mosque as a channel to the community towards understanding of the
identity and also the framework of design thinking in ornaments
particularly to the urban mosques in Malaysia.
Abstract: Speeded-Up Robust Feature (SURF) is commonly used for feature matching in stereovision because of their robustness towards scale changes and rotational changes. However, SURF feature cannot cope with large viewpoint changes or skew distortion. This paper introduces a method which can help to improve the wide baseline-s matching performance in term of accuracy by rectifying the image using two vanishing points. Simplified orientation correction was used to remove the false matching..
Abstract: This paper aims to study decomposition behavior in
pyrolytic environment of four lignocellulosic biomass (oil palm shell,
oil palm frond, rice husk and paddy straw), and two commercial
components of biomass (pure cellulose and lignin), performed in a
thermogravimetry analyzer (TGA). The unit which consists of a
microbalance and a furnace flowed with 100 cc (STP) min-1 Nitrogen,
N2 as inert. Heating rate was set at 20⁰C min-1 and temperature
started from 50 to 900⁰C. Hydrogen gas production during the
pyrolysis was observed using Agilent Gas Chromatography Analyzer
7890A. Oil palm shell, oil palm frond, paddy straw and rice husk
were found to be reactive enough in a pyrolytic environment of up to
900°C since pyrolysis of these biomass starts at temperature as low as
200°C and maximum value of weight loss is achieved at about
500°C. Since there was not much different in the cellulose,
hemicelluloses and lignin fractions between oil palm shell, oil palm
frond, paddy straw and rice husk, the T-50 and R-50 values obtained
are almost similar. H2 productions started rapidly at this temperature
as well due to the decompositions of biomass inside the TGA.
Biomass with more lignin content such as oil palm shell was found to
have longer duration of H2 production compared to materials of high
cellulose and hemicelluloses contents.
Abstract: As the fossil fuels kept on depleting, intense research in developing hydrogen (H2) as the alternative fuel has been done to cater our tremendous demand for fuel. The potential of H2 as the ultimate clean fuel differs with the fossil fuel that releases significant amounts of carbon dioxide (CO2) into the surrounding and leads to the global warming. The experimental work was carried out to study the production of H2 from palm kernel shell steam gasification at different variables such as heating rate, steam to biomass ratio and adsorbent to biomass ratio. Maximum H2 composition which is 61% (volume basis) was obtained at heating rate of 100oCmin-1, steam/biomass of 2:1 ratio, and adsorbent/biomass of 1:1 ratio. The commercial adsorbent had been modified by utilizing the alcoholwater mixture. Characteristics of both adsorbents were investigated and it is concluded that flowability and floodability of modified CaO is significantly improved.
Abstract: The modeling of sound radiation is of fundamental importance for understanding the propagation of acoustic waves and, consequently, develop mechanisms for reducing acoustic noise. The propagation of acoustic waves, are involved in various phenomena such as radiation, absorption, transmission and reflection. The radiation is studied through the linear equation of the acoustic wave that is obtained through the equation for the Conservation of Momentum, equation of State and Continuity. From these equations, is the Helmholtz differential equation that describes the problem of acoustic radiation. In this paper we obtained the solution of the Helmholtz differential equation for an infinite cylinder in a pulsating through free and homogeneous. The analytical solution is implemented and the results are compared with the literature. A numerical formulation for this problem is obtained using the Boundary Element Method (BEM). This method has great power for solving certain acoustical problems in open field, compared to differential methods. BEM reduces the size of the problem, thereby simplifying the input data to be worked and reducing the computational time used.
Abstract: Cutting fluids, usually in the form of a liquid, are
applied to the chip formation zone in order to improve the cutting
conditions. Cutting fluid can be expensive and represents a biological
and environmental hazard that requires proper recycling and
disposal, thus adding to the cost of the machining operation. For
these reasons dry cutting or dry machining has become an
increasingly important approach; in dry machining no coolant or
lubricant is used. This paper discussed the effect of the dry cutting on
cutting force and tool life when machining aerospace materials
(Haynes 242) with using two different coated carbide cutting tools
(TiAlN and TiN/MT-TiCN/TiN). Response surface method (RSM)
was used to minimize the number of experiments. ParTiAlN Swarm
Optimisation (PSO) models were developed to optimize the
machining parameters (cutting speed, federate and axial depth) and
obtain the optimum cutting force and tool life. It observed that
carbide cutting tool coated with TiAlN performed better in dry
cutting compared with TiN/MT-TiCN/TiN. On other hand, TiAlN
performed more superior with using of 100 % water soluble coolant.
Due to the high temperature produced by aerospace materials, the
cutting tool still required lubricant to sustain the heat transfer from
the workpiece.
Abstract: In this paper by using the port-controlled Hamiltonian
(PCH) systems theory, a full-order nonlinear controlled model is first
developed. Then a nonlinear passivity-based robust adaptive control
(PBRAC) of switched reluctance motor in the presence of external
disturbances for the purpose of torque ripple reduction and
characteristic improvement is presented. The proposed controller
design is separated into the inner loop and the outer loop controller.
In the inner loop, passivity-based control is employed by using
energy shaping techniques to produce the proper switching function.
The outer loop control is employed by robust adaptive controller to
determine the appropriate Torque command. It can also overcome the
inherent nonlinear characteristics of the system and make the whole
system robust to uncertainties and bounded disturbances. A 4KW 8/6
SRM with experimental characteristics that takes magnetic saturation
into account is modeled, simulation results show that the proposed
scheme has good performance and practical application prospects.
Abstract: Determination of wellbore problems during a
production/injection process might be evaluated thorough
temperature log analysis. Other applications of this kind of log
analysis may also include evaluation of fluid distribution analysis
along the wellbore and identification of anomalies encountered
during production/injection process. While the accuracy of such
prediction is paramount, the common method of determination of a
wellbore temperature log includes use of steady-state energy balance
equations, which hardly describe the real conditions as observed in
typical oil and gas flowing wells during production operation; and
thus increase level of uncertainties. In this study, a practical method
has been proposed through development of a simplified semianalytical
model to apply for predicting temperature profile along the
wellbore. The developed model includes an overall heat transfer
coefficient accounting all modes of heat transferring mechanism,
which has been focused on the prediction of a temperature profile as
a function of depth for the injection/production wells. The model has
been validated with the results obtained from numerical simulation.
Abstract: The mechanical and tribological properties in WC-Co
coatings are strongly affected by hardness and elasticity
specifications. The results revealed the effect of spraying distance on
microhardness and elasticity modulus of coatings. The metallurgical
studies have been made on coated samples using optical microscopy,
scanning electron microscopy (SEM).
Abstract: Recently electric vehicles are becoming popular as an
alternative of conventional fossil fuel vehicles. Conventional Internal
Combustion Engine (ICE) vehicle uses fossil fuel which contributing
a major part of overall carbon emission in the environment. Carbon
and other green house gas emission are responsible for global
warming and resulting climate change. It becomes vital to evaluate
performance of vehicle based on emission. In this paper an effort has
been made to depict the picture of emission caused by vehicle and
scenario of Australia has taken into account. Effort has been made to
compare the fossil based vehicle with electric vehicle in phases. The
study also evaluates advancement in electric vehicle technology,
required infrastructure for sustainability and future scope of
developments. This paper also includes the evaluation of electric
vehicle concept for pollution control and sustainable transport
systems in future. This study can be a benchmark for development of
electric vehicle as low carbon emission alternative for the cities of
tomorrow.
Abstract: The purpose of the present study is the investigation
of the relationship between knowledge management and enabling
managers based on achieving proper function. This research is
descriptive and investigative. The sample includes all male and
female high school managers of first and second regions of Urmia
including 98 school and accordingly 98 managers. The instrument
applied was a questionnaire. To sum up, there is a statistically
significant relationship between knowledge management and
empowering managers. In the end, several suggestions are provided.
Abstract: A rigorous two-dimensional model is developed for simulating the operation of a less-investigated type steam reformer having a considerably lower operating Reynolds number, higher tube diameter, and non-availability of extra steam in the feed compared with conventional steam reformers. Simulation results show that reasonable predictions can only be achieved when certain correlations for wall to fluid heat transfer equations are applied. Due to severe operating conditions, in all cases, strong radial temperature gradients inside the reformer tubes have been found. Furthermore, the results show how a certain catalyst loading profile will affect the operation of the reformer.
Abstract: Socioeconomic stability and development of a
country, can be describe by housing affordability. It is aimed to
ensure the housing provided as one of the key factors that is
affordable by every income earner group whether low-income,
middle income and high income group. This research carried out is to
find out affordability of home ownership level for first medium cost
landed-house by the middle-income group in Selangor, Malaysia. It is
also hope that it could be seen as able to contribute to the knowledge
and understanding on housing affordability level for the middleincome
group and variables that influenced the medium income
group-s ability to own first medium-cost houses.
Abstract: In this research, the laminar heat transfer of natural convection on vertical surfaces has been investigated. Most of the studies on natural convection have been considered constantly whereas velocity and temperature domain, do not change with time, transient one are used a lot. Governing equations are solved using a finite volume approach. The convective terms are discretized using the power-law scheme, whereas for diffusive terms the central difference is employed. Coupling between the velocity and pressure is made with SIMPLE algorithm. The resultant system of discretized linear algebraic equations is solved with an alternating direction implicit scheme. Then a configuration of rectangular fins is put in different ways on the surface and heat transfer of natural convection on these surfaces without sliding is studied and finally optimization is done.
Abstract: Evaluation of contact pressure, surface and
subsurface contact stresses are essential to know the functional
response of surface coatings and the contact behavior mainly depends
on surface roughness, material property, thickness of layer and the
manner of loading. Contact parameter evaluation of real rough
surface contacts mostly relies on statistical single asperity contact
approaches. In this work, a three dimensional layered solid rough
surface in contact with a rigid flat is modeled and analyzed using
finite element method. The rough surface of layered solid is
generated by FFT approach. The generated rough surface is exported
to a finite element method based ANSYS package through which the
bottom up solid modeling is employed to create a deformable solid
model with a layered solid rough surface on top. The discretization
and contact analysis are carried by using the same ANSYS package.
The elastic, elastoplastic and plastic deformations are continuous in
the present finite element method unlike many other contact models.
The Young-s modulus to yield strength ratio of layer is varied in the
present work to observe the contact parameters effect while keeping
the surface roughness and substrate material properties as constant.
The contacting asperities attain elastic, elastoplastic and plastic states
with their continuity and asperity interaction phenomena is inherently
included. The resultant contact parameters show that neighboring
asperity interaction and the Young-s modulus to yield strength ratio
of layer influence the bulk deformation consequently affect the
interface strength.