Abstract: This study analyzed the effect of area variables and
economic variables on the length of each period of the project in order
to analyze the effect of agreement rate on project implementation in
housing renewal projects. In conclusion, as can be seen from these
results, a low agreement rate may not translate into project promotion,
and a higher agreement rate may not translate into project delay. The
expectation of the policy is that the lower the agreement rate, the more
projects would be promoted, but that is not the actual effect. From a
policy consistency viewpoint, changing the agreement rate frequently,
depending on the decision of the public, is not reasonable. The policy
of using agreement rate as a necessary condition for project
implementation should be reconsidered.
Abstract: This study was carried out for an underground subway station at Seoul Metro, Korea. The optimal set-points of the ventilation control system are determined every 3 hours, then, the ventilation controller adjusts the ventilation fan speed according to the optimal set-point changes. Compared to manual ventilation system which is operated irrespective of the OAQ, the IDP-based ventilation control system saves 3.7% of the energy consumption. Compared to the fixed set-point controller which is operated irrespective of the IAQ diurnal variation, the IDP-based controller shows better performance with a 2% decrease in energy consumption, maintaining the comfortable IAQ range inside the station.
Abstract: Because current wireless communication requires high
reliability in a limited bandwidth environment, this paper proposes
the variable modulation scheme based on the codebook. The variable
modulation scheme adjusts transmission power using the codebook in
accordance with channel state. Also, if the codebook is composed of
many bits, the reliability is more improved by the proposed scheme.
The simulation results show that the performance of proposed scheme
has better reliability than the the performance of conventional scheme.
Abstract: This study identifies factors underlying the digital
divide that is faced by the disabled. The results of its analysis showed
that the digital divide in PC use is affected by age, number of years of
education, employment status, and household income of more than
KRW 3 million. The digital divide in smart device use is affected by
sex, age, number of years of education, time when disability struck,
and household income of more than KRW 3 million. Based on these
results, this study proposes methods for bridging the digital divide
faced by the disabled.
Abstract: The purpose of this study is to determine the
relationship of anxiety level between male and female undergraduates
at a private university in Malaysia. Convenient sampling method used
in this study in which the students were selected based on the
grouping assigned by the faculty. There were 214 undergraduates
who registered the probability courses had participated in this study.
Mathematics Anxiety Rating Scale (MARS) was the instrument used
in study which used to determine students’ anxiety level towards
probability. Reliability and validity of instrument was done before the
major study was conducted. In the major study, students were given
briefing about the study conducted. Participation of this study was
voluntary. Students were given consent form to determine whether
they agree to participate in the study. Duration of two weeks was
given for students to complete the given online questionnaire. The
data collected will be analyzed using Statistical Package for the
Social Sciences (SPSS) to determine the level of anxiety. There were
three anxiety level, i.e., low, average and high. Students’ anxiety
level was determined based on their scores obtained compared with
the mean and standard deviation. If the scores obtained were below
mean and standard deviation, the anxiety level was low. If the scores
were at below and above the mean and between one standard
deviation, the anxiety level was average. If the scores were above the
mean and greater than one standard deviation, the anxiety level was
high. Results showed that both of genders were having average
anxiety level. Among low, average and high anxiety level, frequency
of males were found to be higher as compared to females. Hence, the
mean values obtained for males (M = 3.62) was higher than females
(M = 3.42). In order to be significant of anxiety level among the
gender, the p-value should be less than .05. The p-value obtained in
this study was .117. However, this value was greater than .05. Thus,
there was no significant difference of anxiety level among the gender.
In other words, there was no relationship of anxiety level with the
gender.
Abstract: Currently there are many use of threaded reinforcing
bars in construction fields because those do not need additional screw
processing when connecting reinforcing bar by threaded coupler. In
this study, reinforced concrete bridge piers using threaded rebar
coupler system at the plastic hinge area were tested to evaluate seismic
performance. The test results showed that threads of the threaded rebar
coupler system could be loosened while under tension-compression
cyclic loading because tolerance and rib face angle of a threaded rebar
coupler system are greater than that of a conventional ribbed rebar
coupler system. As a result, cracks were concentrated just outside of
the mechanical coupler and stiffness of reinforced concrete bridge pier
decreased. Therefore, it is recommended that connection ratio of
mechanical couplers in one section shall be below 50% in order that
cracks are not concentrated just outside of the mechanical coupler.
Also, reduced stiffness of the specimen should be considered when
using the threaded rebar coupler system.
Abstract: In recent years, fire accidents have been steadily
increased and the amount of property damage caused by the accidents
has gradually raised. Damaging building structure, fire incidents bring
about not only such property damage but also strength degradation and
member deformation. As a result, the building structure undermines its
structural ability. Examining the degradation and the deformation is
very important because reusing the building is more economical than
reconstruction. Therefore, engineers need to investigate the strength
degradation and member deformation well, and make sure that they
apply right rehabilitation methods. This study aims at evaluating
deformation characteristics of fire damaged and rehabilitated normal
strength concrete beams through both experiments and finite element
analyses. For the experiments, control beams, fire damaged beams and
rehabilitated beams are tested to examine deformation characteristics.
Ten test beam specimens with compressive strength of 21MPa are
fabricated and main test variables are selected as cover thickness of
40mm and 50mm and fire exposure time of 1 hour or 2 hours. After
heating, fire damaged beams are air-recurred for 2 months and
rehabilitated beams are repaired with polymeric cement mortar after
being removed the fire damaged concrete cover. All beam specimens
are tested under four points loading. FE analyses are executed to
investigate the effects of main parameters applied to experimental
study. Test results show that both maximum load and stiffness of the
rehabilitated beams are higher than those of the fire damaged beams.
In addition, predicted structural behaviors from the analyses also show
good rehabilitation effect and the predicted load-deflection curves are
similar to the experimental results. For the further, the proposed
analytical method can be used to predict deformation characteristics of
fire damaged and rehabilitated concrete beams without suffering from
time and cost consuming of experimental process.
Abstract: In the cooperative transmission scheme, both the
cellular system and broadcasting system are composed. Two cellular
base stations (CBSs) communicating with a user in the cell edge use
cooperative transmission scheme in the conventional scheme. In the
case that the distance between two CBSs and the user is distant, the
conventional scheme does not guarantee the quality of the
communication because the channel condition is bad. Therefore, if the
distance between CBSs and a user is distant, the performance of the
conventional scheme is decreased. Also, the bad channel condition has
bad effects on the performance. The proposed scheme uses two relays
to communicate well with CBSs when the channel condition between
CBSs and the user is poor. Using the relay in the high attenuation
environment can obtain both advantages of the high bit error rate
(BER) and throughput performance.
Abstract: Single angle connections, which are bolted to the beam
web and the column flange, are studied to investigate their
moment-rotation behavior. Elastic–perfectly plastic material behavior
is assumed. ABAQUS software is used to analyze the nonlinear
behavior of a single angle connection. The identical geometric and
material conditions with Lipson’s test are used for verifying finite
element models. Since Kishi and Chen’s Power model and Lee and
Moon’s Log model are accurate only for a limited range of mechanism,
simpler and more accurate hyperbolic function models are proposed.
Abstract: This study suggests the estimation method of stress
distribution for the beam structures based on TLS (Terrestrial Laser
Scanning). The main components of method are the creation of the
lattices of raw data from TLS to satisfy the suitable condition and
application of CSSI (Cubic Smoothing Spline Interpolation) for
estimating stress distribution. Estimation of stress distribution for the
structural member or the whole structure is one of the important
factors for safety evaluation of the structure. Existing sensors which
include ESG (Electric strain gauge) and LVDT (Linear Variable
Differential Transformer) can be categorized as contact type sensor
which should be installed on the structural members and also there are
various limitations such as the need of separate space where the
network cables are installed and the difficulty of access for sensor
installation in real buildings. To overcome these problems inherent in
the contact type sensors, TLS system of LiDAR (light detection and
ranging), which can measure the displacement of a target in a long
range without the influence of surrounding environment and also get
the whole shape of the structure, has been applied to the field of
structural health monitoring. The important characteristic of TLS
measuring is a formation of point clouds which has many points
including the local coordinate. Point clouds are not linear distribution
but dispersed shape. Thus, to analyze point clouds, the interpolation is
needed vitally. Through formation of averaged lattices and CSSI for
the raw data, the method which can estimate the displacement of
simple beam was developed. Also, the developed method can be
extended to calculate the strain and finally applicable to estimate a
stress distribution of a structural member. To verify the validity of the
method, the loading test on a simple beam was conducted and TLS
measured it. Through a comparison of the estimated stress and
reference stress, the validity of the method is confirmed.
Abstract: In this paper, improved performance scheme for
joint transmission (JT) is proposed in downlink (DL) coordinated
multi-point (CoMP) in case of the constraint transmission power.
This scheme is that a serving transmission point (TP) requests the
JT to an inter-TP and it selects a precoding technique according
to the channel state information (CSI) from user equipment (UE).
The simulation results show that the bit error rate (BER) and the
throughput performances of the proposed scheme provide the high
spectral efficiency and the reliable data at the cell edge.
Abstract: The conventional Wi-Fi backscatter system can only
process one-to-one communication between the Wi-Fi reader and the
Wi-Fi tag. For improvement of throughput of the conventional system,
this paper proposes the multi-to-multi communication system. In the
proposed system, the interference by the multi-to-multi
communication is effectively cancelled by the orthogonal multiple
access based on the identification code of the tag. Although the
overhead is generated by the procedure for the multi-to-multi
communication, because the procedure is processed by the Wi-Fi
protocol, the overhead is insignificant for the entire communication
procedure. From the numerical results, it is confirmed that the
proposed system has nearly proportional increased throughput in
according to the number of the tag that simultaneously participates in
communication.
Abstract: Aging infrastructures became a serious social problem.
This brought out the increased need for the legislation of a new strict
guideline for infrastructure management. Although existing guidelines
provided basics of how to evaluate and manage the condition of
infrastructures, they needed improvements for their evaluation
procedures. Most guidelines mainly focused on the structural
condition of infrastructures and did not properly reflect service aspects
of infrastructures such as performance, public demand, capacity, etc.,
which were significantly valuable to public. Regardless of the
importance, these factors were often neglected in infrastructure
evaluations, because they were quite subjective and difficult to
quantify in rational manner. Thus, this study proposed a framework to
properly identify and evaluate the service indicators. This study
showed that service indicators could be grouped into two categories
and properly evaluated using AHP and Fuzzy. Overall, proposed
framework is expected to assist governmental agency in establishing
effective investment strategies for infrastructure improvements.
Abstract: The aim of this research was to reveal the link
between mental variables, such as spatial abilities, memory, intellect
and professional experience of drivers.
Participants were allocated to four groups: no experience,
inexperienced, skilled and professionals (total 85 participants). The
level of ability for spatial navigation and indicator of nonverbal
memory grow along the process of accumulation of driving
experience. At high levels of driving experience, this tendency is
especially noticeable. The professionals having personal
achievements in driving (racing) differ from skilled drivers in better
feeling of direction, which is specific for them not just in a short-term
situation of an experimental task, but also in life-size perspective.
The level of ability of mental rotation does not grow with the growth
of driving experience, which confirms the multiple intelligence
theory according to which spatial abilities represent specific, other
than logical intelligence type of intellect. The link between spatial
abilities, memory, intellect and professional experience of drivers
seems to be different relating spatial navigation or mental rotation as
different kinds of spatial abilities.
Abstract: In this paper, the actuality of the study, and the role of
subjective well-being problem in modern psychology and the
comprehending of subjective well-being by current students is
defined. The purpose of this research is to educe peculiarities of
comprehending of subjective well-being by students with various
levels of emotional intelligence. Methods of research are adapted
Russian-Language questionnaire of K. Riff 'The scales of
psychological well-being'; emotional intelligence questionnaire of D.
V. Lusin. The research involved 72 students from different
universities and disciplines aged between 18 and 24. Analyzing the
results of the studies, it can be concluded that the understanding of
happiness in different groups of students with high and low levels of
overall emotional intelligence is different, as well as differentiated by
gender. Students with a higher level of happiness possess more
capacity and higher need to control their emotions, to cause and
maintain the desired emotions and control something undesirable.
Abstract: In this paper, we proposed a novel SCR (Silicon Controlled
Rectifier) - based ESD (Electrostatic Discharge) protection device for I/O
and power clamp. The proposed device has a higher holding voltage
characteristic than conventional SCR. These characteristics enable to have
latch-up immunity under normal operating conditions as well as superior full
chip ESD protection. The proposed device was analyzed to figure out
electrical characteristics and tolerance robustness in term of individual
design parameters (D1, D2, D3). They are investigated by using the
Synopsys TCAD simulator. As a result of simulation, holding voltage
increased with different design parameters. The holding voltage of the
proposed device changes from 3.3V to 7.9V. Also, N-Stack structure ESD
device with the high holding voltage is proposed. In the simulation results,
2-stack has holding voltage of 6.8V and 3-stack has holding voltage of
10.5V. The simulation results show that holding voltage of stacking
structure can be larger than the operation voltage of high-voltage
application.
Abstract: An experiment was conducted to elucidate the effects of turmeric powder supplementation on egg production performance of old laying hens (80 weeks of age). There were 40 hens of Hysex Brown strain used in the study. They were caged individually, and randomly divided into 4 treatment groups of diet containing 0 (control), 1, 2 and 4 % oven dried turmeric powder for 3 periods of 4 weeks; Egg production (% hen day) and feed intake of the 4 treatment groups at the commencement of the experiment were not significantly different. In addition to egg production performance (% and egg weight), feed and water intakes were measured daily, and cholesterol content of the whole egg was determined. The results indicated that feed intakes of the hen were significantly lowered when 4% turmeric powder supplemented, while there were no significant changes in water intakes. Egg production were significantly increased and maintained at a higher level by turmeric powder supplementation up to 4% compared with the control, while the weight of eggs were not significantly affected. The research markedly demonstrated that supplementation of turmeric powder up to 4% could improve and maintain egg production performance of the old laying hen at a higher level with a lower cholesterol content.
Abstract: This study will examine how the therapeutic factors
(therapeutic catharsis-seeking and game-efficacy of the game player)
and self-construal factors (independent and interdependent
self-construal of the game player) as well as social capital factors
(bonding and bridging social capital of the game player) affect
aggression in the game. Results show that both therapeutic
catharsis-seeking and game self-efficacy are particularly important to
the players since they cause the game players’ aggressive tendencies to
be greatly diminished. Independent self-construal reduces the level of
the players’ aggression. Interestingly enough, the bonding social
capital enhances the level of the players’ aggression, while individuals
with bridging social capital did not show any significant effects. The
results and implications will be discussed herein.
Abstract: Methicillin/multiple-resistant Staphylococcus aureus
(MRSA) are infectious bacteria that are resistant to common
antibiotics. A previous in silico study in our group has identified a
hypothetical protein SAV1226 as one of the potential drug targets. In
this study, we reported the bioinformatics characterization, as well as
cloning, expression, purification and kinetic assays of hypothetical
protein SAV1226 from methicillin/vancomycin-resistant
Staphylococcus aureus Mu50 strain. MALDI-TOF/MS analysis
revealed a low degree of structural similarity with known proteins.
Kinetic assays demonstrated that hypothetical protein SAV1226 is
neither a domain of an ATP dependent dihydroxyacetone kinase nor
of a phosphotransferase system (PTS) dihydroxyacetone kinase,
suggesting that the function of hypothetical protein SAV1226 might
be misannotated on public databases such as UniProt and
InterProScan 5.
Abstract: This study is aiming at establishing the relationship
between the optical signal of flame and an equivalent ratio of flame. In
this experiment, flame optical signal in a furnace is measured using
photodiode. The combustion system is composed of metal fiber burner
and vertical furnace, and flame chemiluminescence is measured at
various experimental conditions. In this study, the flame
chemiluminescence of laminar premixed flame is measured using
commercially available photodiode. It is experimentally investigated
the relationship between equivalent ratio and photodiode signal. In
addition, the strategy of combustion control method is proposed using
the optical signal and fuel pressure.
The results showed that certain relationship between optical data of
photodiode and equivalence ratio exists, and this leads to the
successful application of this system for instantaneous measurement of
equivalence ration of the combustion system.