Abstract: This paper presents comparative emission study of
newly introduced gasoline/LPG bifuel automotive engine in Indian
market. Emissions were tested as per LPG-Bharat stage III driving
cycle. Emission tests were carried out for urban cycle and extra urban
cycle. Total time for urban and extra urban cycle was 1180 sec.
Engine was run in LPG mode by using conversion system. Emissions
were tested as per standard procedure and were compared. Corrected
emissions were computed by deducting ambient reading from sample
reading. Paper describes detail emission test procedure and results
obtained. CO emissions were in the range of38.9 to 111.3 ppm. HC
emissions were in the range of 18.2 to 62.6 ppm. Nox emissions were
08 to 3.9 ppm and CO2 emissions were from 6719.2 to 8051 ppm.
Paper throws light on emission results of LPG vehicles recently
introduced in Indian automobile market. Objectives of this
experimental study were to measure emissions of engines in gasoline
& LPG mode and compare them.
Abstract: We report the results of an lattice Boltzmann
simulation of magnetohydrodynamic damping of sidewall convection
in a rectangular enclosure filled with a porous medium. In particular
we investigate the suppression of convection when a steady magnetic
field is applied in the vertical direction. The left and right vertical
walls of the cavity are kept at constant but different temperatures
while both the top and bottom horizontal walls are insulated. The
effects of the controlling parameters involved in the heat transfer and
hydrodynamic characteristics are studied in detail. The heat and mass
transfer mechanisms and the flow characteristics inside the enclosure
depended strongly on the strength of the magnetic field and Darcy
number. The average Nusselt number decreases with rising values of
the Hartmann number while this increases with increasing values of
the Darcy number.
Abstract: Several methods have been proposed for color image
compression but the reconstructed image had very low signal to noise
ratio which made it inefficient. This paper describes a lossy
compression technique for color images which overcomes the
drawbacks. The technique works on spatial domain where the pixel
values of RGB planes of the input color image is mapped onto two
dimensional planes. The proposed technique produced better results
than JPEG2000, 2DPCA and a comparative study is reported based
on the image quality measures such as PSNR and MSE.Experiments
on real time images are shown that compare this methodology with
previous ones and demonstrate its advantages.
Abstract: Isobaric vapor-liquid equilibrium measurements are
reported for binary mixture of 2-Methyltetrahydrofuran and Cumene
at 97.3 kPa. The data were obtained using a vapor recirculating type
(modified Othmer's) equilibrium still. The mixture shows slight
negative deviation from ideality. The system does not form an
azeotrope. The experimental data obtained in this study are
thermodynamically consistent according to the Herington test. The
activity coefficients have been satisfactorily correlated by means of
the Margules, and NRTL equations. Excess Gibbs free energy has
been calculated from the experimental data. The values of activity
coefficients have also been obtained by the UNIFAC group
contribution method.
Abstract: Water is the main component of biological processes.
Water management is important to obtain higher productivity. In this
study, some of the yield components were investigated together with
different drought levels. Four chickpea genotypes (CDC Frontier,
CDC Luna, Sawyer and Sierra) were grown in pots with 3 different
irrigation levels (a dose of 17.5 ml, 35 ml and 70 ml for each pot per
day) after three weeks from sowing. In the research, flowering, pod
set, pod per plant, fertile pod, double seed/pod, stem diameter, plant
weight, seed per plant, 1000 seed weight, seed diameter, vegetation
length and weekly plant height were measured. Consequently,
significant differences were observed on all the investigated
characteristics owing to genotypes (except double seed/pod and stem
diameter), water levels (except first pod, seed weight and height on
3rd week) and genotype x water level interaction (except first pod,
double seed/pod, seed weight and height).
Abstract: This paper presents the possibilities of using Weibull statistical distribution in modeling the distribution of defects in ERP systems. There follows a case study, which examines helpdesk records of defects that were reported as the result of one ERP subsystem upgrade. The result of the applied modeling is in modeling the reliability of the ERP system from a user perspective with estimated parameters like expected maximum number of defects in one day or predicted minimum of defects between two upgrades. Applied measurement-based analysis framework is proved to be suitable in predicting future states of the reliability of the observed ERP subsystems.
Abstract: The combustion of liquid fuel in the porous burner
(PB) was experimented to investigate evaporation mechanism and
combustion behavior. The diesel oil was used as fuel and the pebbles
carefully chosen in the same size like the solid sphere homogeneously
was adopted as the porous media. Two structures of the liquid porous
burner, i.e. the PB without and with installation of porous emitter
(PE), were performed. PE was installed by lower than PB with
distance of 20 cm. The pebbles having porosity (φ) of 0.45 and 0.52
were, respectively, used in PB and PE. The fuel was supplied dropwise
from the top through the PB and the combustion was occurred between
PB and PE. Axial profiles of temperature along the burner length were
measured to clarify the evaporation and combustion phenomena. The
pollutant emission characteristics were monitored at the burner exit.
From the experiment, it was found that the temperature profiles of both
structures decreased with the three ways swirling air flows (QA)
increasing. On the other hand, the temperature profiles increased with
fuel heat input (QF). Obviously, the profile of the porous burner
installed with PE was higher than that of the porous burner without
PE
Abstract: Employees commitments of vision and mission of
organization is effected due to manager’s executes by approach of
leadership The leaders who have attributions like vision, confidence
and correctitude, sharing and participation, creativeness, progressive
learning –improvement and responsibility are effective to increase
organizational commitment if they are sensitive to expectation and
requirement of employees in an organization. Studies about
organizational commitment appear results that employees who have
strong organizational commitment have the most contribution. In this
study, “Leadership” and “Organizational Commitment” conduct
surveys to 31 employees of Ahmet Özdemir Nak. Tic. San. A.Ş.
which has operations in road and railway transportation sector. It is
analyzed the effects of leadership approach to organizational
commitment deals with result of survey.
Abstract: Direction of Arrival estimation refers to defining a mathematical function called a pseudospectrum that gives an indication of the angle a signal is impinging on the antenna array. This estimation is an efficient method of improving the quality of service in a communication system by focusing the reception and transmission only in the estimated direction thereby increasing fidelity with a provision to suppress interferers. This improvement is largely dependent on the performance of the algorithm employed in the estimation. Many DOA algorithms exists amongst which are MUSIC, Root-MUSIC and ESPRIT. In this paper, performance of these three algorithms is analyzed in terms of complexity, accuracy as assessed and characterized by the CRLB and memory requirements in various environments and array sizes. It is found that the three algorithms are high resolution and dependent on the operating environment and the array size.
Abstract: Magnesium alloys have gained increased attention in recent years in automotive, electronics, and medical industry. This because of magnesium alloys have better properties than aluminum alloys and steels in respects of their low density and high strength to weight ratio. However, the main problems of magnesium alloy welding are the crack formation and the appearance of porosity during the solidification. This paper proposes a unique technique to weld two thin sheets of AZ31B magnesium alloy using a paste containing Ag nanoparticles. The paste containing Ag nanoparticles of 5 nm in average diameter and an organic solvent was used to coat the surface of AZ31B thin sheet. The coated sheet was heated at 100 °C for 60 s to evaporate the solvent. The dried sheet was set as a lower AZ31B sheet on the jig, and then lap fillet welding was carried out by using a pulsed Nd:YAG laser in a closed box filled with argon gas. The characteristics of the microstructure and the corrosion behavior of the joints were analyzed by opticalmicroscopy (OM), energy dispersive spectrometry (EDS), electron probe micro-analyzer (EPMA), scanning electron microscopy (SEM), and immersion corrosion test. The experimental results show that the wrought AZ31B magnesium alloy can be joined successfully using Ag nanoparticles. Ag nanoparticles insert promote grain refinement, narrower the HAZ width and wider bond width compared to weld without and insert. Corrosion rate of welded AZ31B with Ag nanoparticles reduced up to 44 % compared to base metal. The improvement of corrosion resistance of welded AZ31B with Ag nanoparticles due to finer grains and large grain boundaries area which consist of high Al content. β-phase Mg17Al12 could serve as effective barrier and suppressed further propagation of corrosion. Furthermore, Ag distribution in fusion zone provide much more finer grains and may stabilize the magnesium solid solution making it less soluble or less anodic in aqueous
Abstract: In the given article the creative arts is being
investigated in the modern era and from the aspect of the artistic
interrelationship, having created by the character of his personality
and as the viewer. A study in the identity formation terms, the
definition of its being unique, unity and similarity as a global issue of
the XXI century has been conducted by the analyzing the definitions
which characterize the human nature in the arts. Spiritual universality
and human existence have been considered in the art system as a
human who is a creator, as the man hero and as the character who is
the recipient as well as the analyses which have been conducted
along with the worldwide cultural and historical processes.
Abstract: This study developed a high efficient and combined
biological and chemical filter treatment process. This process used
PAC (Powder Activated Carbon), Alum and attached growth
treatment process. The system removals of total nitrogen and total
phosphorus ratio of two were as high as 70% and 73%, moreover, the
effluent water was suitable to urban and agricultural water. Also the
advantages of this process are not only occupies small place but is
simple, economic and easy operating. Besides, our developed process
can keep stable process efficiency even in relative low load level.
Therefore, this study judges that use of the high efficient and
combined biological and chemical filter treatment process, it is
expected that the effluent water in this system can be reused as urban
and agricultural water.
Abstract: In this paper, various algorithms for designing quadrature mirror filter are reviewed and a new algorithm is presented for the design of near perfect reconstruction quadrature mirror filter bank. In the proposed algorithm, objective function is formulated using the perfect reconstruction condition or magnitude response condition of prototype filter at frequency (ω = 0.5π) in ideal condition. The cutoff frequency is iteratively changed to adjust the filters coefficients using optimization algorithm. The performances of the proposed algorithm are evaluated in term of computation time, reconstruction error and number of iterations. The design examples illustrate that the proposed algorithm is superior in term of peak reconstruction error, computation time, and number of iterations. The proposed algorithm is simple, easy to implement, and linear in nature.
Abstract: The general global behavior of particle S a non-linear (Q - xy)2 potential cannot be revealed a Poincare surface of section method (PSS) because inost trajectories take practically infinitely long time to integrate numerically before they come back to the surface. In this study as an alternative to PSS, a multiple scale perturbation is applied to analyze global adiabatic, non-adiabatic and chaotic behavior of particles in this potential. It was found that the results can be summarized as a form of a Fermi-like map. Additionally, this method gives a variation of global stochasticity criteria with Q.
Abstract: Zeolite A and MCM-41 have extensive applications in basic science, petrochemical science, energy conservation/storage, medicine, chemical sensor, air purification, environmentally benign composite structure and waste remediation. However, the use of zeolite A and MCM-41 in these areas, especially environmental remediation, are restricted due to prohibitive production cost. Efficient recycling of and resource recovery from coal fly ash has been a major topic of current international research interest, aimed at achieving sustainable development of human society from the viewpoints of energy, economy, and environmental strategy. This project reported an original, novel, green and fast methods to produce nano-porous zeolite A and MCM-41 materials from coal fly ash. For zeolite A, this novel production method allows a reduction by half of the total production time while maintaining a high degree of crystallinity of zeolite A which exists in a narrower particle size distribution. For MCM-41, this remarkably green approach, being an environmentally friendly process and reducing generation of toxic waste, can produce pure and long-range ordered MCM-41 materials from coal fly ash. This approach took 24 h at 25 oC to produce 9 g of MCM-41 materials from 30 g of the coal fly ash, which is the shortest time and lowest reaction temperature required to produce pure and ordered MCM-41 materials (having the largest internal surface area) compared to the values reported in the literature. Performance evaluation of the produced zeolite A and MCM-41 materials in wastewater treatment and air pollution control were reported. The residual fly ash was also converted to zeolite Na-P1 which showed good performance in removal of multi-metal ions in wastewater. In wastewater treatment, compared to commercial-grade zeolite A, adsorbents produced from coal fly ash were effective in removing multi heavy metal ions in water and could be an alternative material for treatment of wastewater. In methane emission abatement, the zeolite A (produced from coal fly ash) achieved similar methane removal efficiency compared to the zeolite A prepared from pure chemicals. This report provides the guidance for production of zeolite A and MCM-41 from coal fly ash by a cost-effective approach which opens potential applications of these materials in environmental industry. Finally, environmental and economic aspects of production of zeolite A and MCM-41 from coal fly ash were discussed.
Abstract: The crystalline quality of the AlGaN/GaN high electron mobility transistor (HEMT) structure grown on a 200 mm silicon substrate has been investigated using UV-visible micro- Raman scattering and photoluminescence (PL). The visible Raman scattering probes the whole nitride stack with the Si substrate and shows the presence of a small component of residual in-plane stress in the thick GaN buffer resulting from a wafer bowing, while the UV micro-Raman indicates a tensile interfacial stress induced at the top GaN/AlGaN/AlN layers. PL shows a good crystal quality GaN channel where the yellow band intensity is very low compared to that of the near-band-edge transition. The uniformity of this sample is shown by measurements from several points across the epiwafer.
Abstract: Falling has been one of the major concerns and threats
to the independence of the elderly in their daily lives. With the
worldwide significant growth of the aging population, it is essential
to have a promising solution of fall detection which is able to operate
at high accuracy in real-time and supports large scale implementation
using multiple cameras. Field Programmable Gate Array (FPGA) is a
highly promising tool to be used as a hardware accelerator in many
emerging embedded vision based system. Thus, it is the main
objective of this paper to present an FPGA-based solution of visual
based fall detection to meet stringent real-time requirements with
high accuracy. The hardware architecture of visual based fall
detection which utilizes the pixel locality to reduce memory accesses
is proposed. By exploiting the parallel and pipeline architecture of
FPGA, our hardware implementation of visual based fall detection
using FGPA is able to achieve a performance of 60fps for a series of
video analytical functions at VGA resolutions (640x480). The results
of this work show that FPGA has great potentials and impacts in
enabling large scale vision system in the future healthcare industry
due to its flexibility and scalability.
Abstract: In this paper, a novel contrast enhancement technique
for contrast enhancement of a low-contrast satellite image has been
proposed based on the singular value decomposition (SVD) and
discrete cosine transform (DCT). The singular value matrix
represents the intensity information of the given image and any
change on the singular values change the intensity of the input image.
The proposed technique converts the image into the SVD-DCT
domain and after normalizing the singular value matrix; the enhanced
image is reconstructed by using inverse DCT. The visual and
quantitative results suggest that the proposed SVD-DCT method
clearly shows the increased efficiency and flexibility of the proposed
method over the exiting methods such as Linear Contrast Stretching
technique, GHE technique, DWT-SVD technique, DWT technique,
Decorrelation Stretching technique, Gamma Correction method
based techniques.
Abstract: Partitioning is a critical area of VLSI CAD. In order to build complex digital logic circuits its often essential to sub-divide multi -million transistor design into manageable Pieces. This paper looks at the various partitioning techniques aspects of VLSI CAD, targeted at various applications. We proposed an evolutionary time-series model and a statistical glitch prediction system using a neural network with selection of global feature by making use of clustering method model, for partitioning a circuit. For evolutionary time-series model, we made use of genetic, memetic & neuro-memetic techniques. Our work focused in use of clustering methods - K-means & EM methodology. A comparative study is provided for all techniques to solve the problem of circuit partitioning pertaining to VLSI design. The performance of all approaches is compared using benchmark data provided by MCNC standard cell placement benchmark net lists. Analysis of the investigational results proved that the Neuro-memetic model achieves greater performance then other model in recognizing sub-circuits with minimum amount of interconnections between them.
Abstract: Water is the key of national development. Wherever a spring has been dried out or a river has changed its course, the area-s people have migrated and have been scattered and the area-s civilization has lost its brilliance. Today, air pollution, global warming and ozone layer damage are as the problems of countries, but certainly in the next decade the shortage and pollution of waters will be important issues of the world. The polluted waters are more dangerous in when they are used in agriculture. Because they infect plants and these plants are used in human and livestock consumption in food chain. With the increasing population growth and after that, the increase need to facilities and raw materials, human beings has started to do haste actions and wanted or unwanted destroyed his life basin. They try to overuse and capture his environment extremely, instead of having futurism approach in sustainable use of nature. This process includes Zayanderood recession, and caused its pollution after the transition from industrial and urban areas. Zayandehrood River in Isfahan is a vital artery of a living ecosystem. Now is the location of disposal waste water of many cities, villages and existing industries. The central area of the province is an important industrial place, and its environmental situation has reached a critical stage. Not only a large number of pollution-generating industries are active in the city limits, but outside of the city and adjacent districts Zayandehrood River, heavy industries like steel, Mobarakeh Steel and other tens great units pollute wild life. This article tries to study contaminant sources of Zayanderood and their severity, and determine and discuss the share of each of these resources by major industrial centers located in areas. At the end, we represent suitable strategy.