Abstract: This paper introduces a method to optimal design of a
hybrid Wind/Photovoltaic/Fuel cell generation system for a typical
domestic load that is not located near the electricity grid. In this
configuration the combination of a battery, an electrolyser, and a
hydrogen storage tank are used as the energy storage system. The aim
of this design is minimization of overall cost of generation scheme
over 20 years of operation. The Matlab/Simulink is applied for
choosing the appropriate structure and the optimization of system
sizing. A teaching learning based optimization is used to optimize the
cost function. An overall power management strategy is designed for
the proposed system to manage power flows among the different
energy sources and the storage unit in the system. The results have
been analyzed in terms of technical and economic. The simulation
results indicate that the proposed hybrid system would be a feasible
solution for stand-alone applications at remote locations.
Abstract: Graphene was dispersed using a tip sonicator and the
effect of surfactants were analysed. Sodium Dodecyl Sulphate (SDS)
and Polyvinyl Alcohol (PVA) were compared to observe whether or
not they had any effect on any de-wrinkling, and secondly whether
they aided to achieve better dispersions. There is a huge demand for
wrinkle free graphene as this will greatly increase its usefulness in
various engineering applications. A comprehensive literature on dewrinkling
graphene has been discussed. Low magnification Scanning
Electronic Microscopy (SEM) was conducted to assess the quality of
graphene de-wrinkling. The utilization of the PVA has significant
effect on de-wrinkling whereas SDS had minimal effect on the dewrinkling
of graphene.
Abstract: The primary objective of this work was to study the
effect of resin chemistry, pH and molarity of binding and elution
buffer on aggregate removal using Cation Exchange Chromatography
and find the optimum conditions which can give efficient aggregate
removal with minimum loss of yield. Four different resins were used
for carrying out the experiments: Fractogel EMD SO3
-(S), Fractogel EMD COO-(M), Capto SP ImpRes and S Ceramic HyperD. Runs
were carried out on the AKTA Avant system. Design of Experiments
(DOE) was used for analysis using the JMP software. The
dependence of the yield obtained using different resins on the
operating conditions was studied. Success has been achieved in
obtaining yield greater than 90% using Capto SP ImpRes and
Fractogel EMD COO-(M) resins. It has also been found that a change
in the operating conditions generally has different effects on the
yields obtained using different resins.
Abstract: The access to relevant information that is adapted to
user’s needs, preferences and environment is a challenge in many
applications running. That causes an appearance of context-aware
systems. To facilitate the development of this class of applications, it
is necessary that these applications share a common context
metamodel. In this article, we will present our context metamodel
that is defined using the OMG Meta Object facility (MOF).This
metamodel is based on the analysis and synthesis of context concepts
proposed in literature.
Abstract: Mobile Ad Hoc Networks (MANETs) is a collection
of mobile devices forming a communication network without
infrastructure. MANET is vulnerable to security threats due to
network’s limited security, dynamic topology, scalability and the lack
of central management. The Quality of Service (QoS) routing in such
networks is limited by network breakage caused by node mobility or
nodes energy depletions. The impact of node mobility on trust
establishment is considered and its use to propagate trust through a
network is investigated in this paper. This work proposes an
enhanced Associativity Based Routing (ABR) with Fuzzy based
Trust (Fuzzy- ABR) routing protocol for MANET to improve QoS
and to mitigate network attacks.
Abstract: This research paper presents the current practices of
teacher professional development, perceived as beneficial by teachers
themselves, in a private secondary school in Brunei Darussalam. This
is part of the findings of a larger qualitative study on teacher
empowerment, using ethnographic methods for data collection, i.e.
participant observation, interviews and document analysis. The field
work was carried out over a period of six months in 2013. An
analysis of the field data revealed multiple pathways of teacher
professional development existing in the school. The results indicate
that school leaders, the teacher community in the school, students,
and the teachers themselves were the agents in a school that
facilitated teacher empowerment. Besides contributing to the
knowledge base on teacher professional development, the results of
this study provide directions for educational policy makers in their
efforts to enhance professional development in secondary schools of
similar characteristics. For school leaders and the teacher community,
these findings offer guidelines for maximizing the opportunities for
these professional development practices, by strengthening
collegiality and by using the existing structures optimally for the
benefit of all concerned.
Abstract: In this research, thorium dioxide mesoporous
nanocrystalline powder was synthesized through the sol-gel method
using hydrated thorium nitrate and ammonium hydroxide as starting
materials and Triton X100 as surfactant. ThO2 gel was characterized
by thermogravimetric (TGA), and prepared ThO2 powder was
subjected to scanning electron microscopy (SEM), X-ray diffraction
(XRD), and Brunauer-Emett-Teller (BET) analyses studies. Detailed
analyses show that prepared powder consisted of phase with the
space group Fm3m of thoria and its crystalline size was 12.6 nm. The
thoria possesses 16.7 m2/g surface area and the pore volume and size
calculated to be 0.0423 cc/g and 1.947 nm, respectively.
Abstract: Useful lifetime evaluation of chevron rubber spring
was very important in design procedure to assure the safety and
reliability. It is, therefore, necessary to establish a suitable criterion
for the replacement period of chevron rubber spring. In this study, we
performed characteristic analysis and useful lifetime prediction of
chevron rubber spring. Rubber material coefficient was obtained by
curve fittings of uniaxial tension equibiaxial tension and pure shear
test. Computer simulation was executed to predict and evaluate the
load capacity and stiffness for chevron rubber spring. In order to
useful lifetime prediction of rubber material, we carried out the
compression set with heat aging test in an oven at the temperature
ranging from 50°C to 100°C during a period 180 days. By using the
Arrhenius plot, several useful lifetime prediction equations for rubber
material was proposed.
Abstract: Computer aided diagnosis systems provide vital
opinion to radiologists in the detection of early signs of breast cancer
from mammogram images. Architectural distortions, masses and
microcalcifications are the major abnormalities. In this paper, a
computer aided diagnosis system has been proposed for
distinguishing abnormal mammograms with architectural distortion
from normal mammogram. Four types of texture features GLCM
texture, GLRLM texture, fractal texture and spectral texture features
for the regions of suspicion are extracted. Support vector machine
has been used as classifier in this study. The proposed system yielded
an overall sensitivity of 96.47% and an accuracy of 96% for
mammogram images collected from digital database for screening
mammography database.
Abstract: This study aims to investigate the mixing behaviors of
deionized (DI) water and carboxymethyl cellulose (CMC) solutions in
C-shaped serpentine micromixers over a wide range of flow
conditions. The flow of CMC solutions exhibits shear-thinning
behaviors. Numerical simulations are performed to investigate the
effects of the mean flow speed, fluid properties and geometry
parameters on flow and mixing in the micromixers with the serpentine
channel of the same overall channel length. From the results, we can
find the following trends. When convection dominates fluid mixing,
the curvature-induced vortices enhance fluid mixing effectively. The
mixing efficiency of a micromixer consisting of semicircular C-shaped
repeating units with a smaller centerline radius is better than that of a
micromixer consisting of major segment repeating units with a larger
centerline radius. The viscosity of DI water is less than the overall
average apparent viscosity of CMC solutions, and so the effect of
curvature-induced vortices on fluid mixing in DI water is larger than
that in CMC solutions for the cases with the same mean flow speed.
Abstract: Barley (Hordeum vulgare L.), vetch (Vicia villosa),
and grass pea (Lathyrus sativus L.) monocultures as well as mixtures
of barley with each of the above legumes, in three seeding ratios (i.e.,
barley: legume 75:25, 50:50 and 25:75, based on seed numbers) were
used to investigated forage yield and competition indices. The results
showed that intercropping reduced the dry matter yield of the three
component plants, compared with their respective monocrops. The
greatest value of total dry matter yield was obtained from barley25-
grasspea75 (5.44 t ha-1) mixture, followed by grass pea sole crop (4.99
t ha-1). The total actual yield loss (AYL) values were positive and
greater than 0 in all mixtures, indicating an advantage from
intercropping over sole crops. Intercropped barley had a higher
relative crowding coefficient (K=1.64) than intercropped legumes
(K=1.20), indicating that barley was more competitive than legumes
in mixtures. Furthermore, grass pea was more competitive than vetch
in mixtures with barley. The highest land equivalent ratio (LER),
system productivity index (SPI) and monetary advantage index
(MAI) were obtained when barley was mixed at a rate of 25% with
75% seed rate of grass pea. It is concluded that intercropping of
barley with grass pea has a good potential to improve the
performance of forage with high land-use efficiency.
Abstract: Over the past few years, a lot of research has been
conducted to bring Automatic Speech Recognition (ASR) into various
areas of Air Traffic Control (ATC), such as air traffic control
simulation and training, monitoring live operators for with the aim
of safety improvements, air traffic controller workload measurement
and conducting analysis on large quantities controller-pilot speech.
Due to the high accuracy requirements of the ATC context and its
unique challenges, automatic speech recognition has not been widely
adopted in this field. With the aim of providing a good starting
point for researchers who are interested bringing automatic speech
recognition into ATC, this paper gives an overview of possibilities
and challenges of applying automatic speech recognition in air traffic
control. To provide this overview, we present an updated literature
review of speech recognition technologies in general, as well as
specific approaches relevant to the ATC context. Based on this
literature review, criteria for selecting speech recognition approaches
for the ATC domain are presented, and remaining challenges and
possible solutions are discussed.
Abstract: The present study applies the inverse method and
three-dimensional CFD commercial software in conjunction with the
experimental temperature data to investigate the heat transfer and fluid
flow characteristics of the plate-fin heat sink in a rectangular closed
enclosure. The inverse method with the finite difference method and
the experimental temperature data is applied to determine the
approximate heat transfer coefficient. Later, based on the obtained
results, the zero-equation turbulence model is used to obtain the heat
transfer and fluid flow characteristics between two fins. T0 validate
the accuracy of the results obtained, the comparison of the heat transfer
coefficient is made. The obtained temperature at selected
measurement locations of the fin is also compared with experimental
data. The effect of the height of the rectangular enclosure on the
obtained results is discussed.
Abstract: An approach was evaluated for the retrieval of soil
moisture of bare soil surface using bistatic scatterometer data in the
angular range of 200 to 700 at VV- and HH- polarization. The
microwave data was acquired by specially designed X-band (10
GHz) bistatic scatterometer. The linear regression analysis was done
between scattering coefficients and soil moisture content to select the
suitable incidence angle for retrieval of soil moisture content. The 250
incidence angle was found more suitable. The support vector
regression analysis was used to approximate the function described
by the input output relationship between the scattering coefficient and
corresponding measured values of the soil moisture content. The
performance of support vector regression algorithm was evaluated by
comparing the observed and the estimated soil moisture content by
statistical performance indices %Bias, root mean squared error
(RMSE) and Nash-Sutcliffe Efficiency (NSE). The values of %Bias,
root mean squared error (RMSE) and Nash-Sutcliffe Efficiency
(NSE) were found 2.9451, 1.0986 and 0.9214 respectively at HHpolarization.
At VV- polarization, the values of %Bias, root mean
squared error (RMSE) and Nash-Sutcliffe Efficiency (NSE) were
found 3.6186, 0.9373 and 0.9428 respectively.
Abstract: The Northeast China (NEC) was the most important
agriculture areas and known as the Golden-Maize-Belt. Based on
observed crop data and crop model, we design four simulating
experiments and separate relative impacts and contribution under
climate change, planting date shift, and varieties change as well
change of varieties and planting date. Without planting date and
varieties change, maize yields had no significant change trend at
Hailun station located in the north of NEC, and presented significant
decrease by 0.2 - 0.4 t/10a at two stations, which located in the middle
and the south of NEC. With planting date change, yields showed a
significant increase by 0.09 - 0.47 t/10a. With varieties change, maize
yields had significant increase by 1.8~ 1.9 t/10a at Hailun and Huadian
stations, but a non-significant and low increase by 0.2t /10a at Benxi
located in the south of NEC. With change of varieties and planting
date, yields presented a significant increasing by 0.53- 2.0 t/10a. Their
contribution to yields was -25% ~ -55% for climate change, 15% ~
35% for planting date change, and 20% ~110% for varieties change as
well 30% ~135% for varieties with planting date shift. It found that
change in varieties and planting date were highest yields and were
responsible for significant increases in maize yields, varieties was
secondly, and planting date was thirdly. It found that adaptation in
varieties and planting date greatly improved maize yields, and
increased yields annual variability. The increase of contribution with
planting date and varieties change in 2000s was lower than in 1990s.
Yields with the varieties change and yields with planting date and
varieties change all showed a decreasing trend at Huadian and Benxi
since 2002 or so. It indicated that maize yields increasing trend
stagnated in the middle and south of NEC, and continued in the north
of NEC.
Abstract: Studying on the response of vegetation phenology to
climate change at different temporal and spatial scales is important for
understanding and predicting future terrestrial ecosystem dynamics
and the adaptation of ecosystems to global change. In this study, the
Moderate Resolution Imaging Spectroradiometer (MODIS)
Normalized Difference Vegetation Index (NDVI) dataset and climate
data were used to analyze the dynamics of grassland phenology as well
as their correlation with climatic factors in different eco-geographic
regions and elevation units across the Tibetan Plateau. The results
showed that during 2003–2012, the start of the grassland greening
season (SOS) appeared later while the end of the growing season
(EOS) appeared earlier following the plateau’s precipitation and heat
gradients from southeast to northwest. The multi-year mean value of
SOS showed differences between various eco-geographic regions and
was significantly impacted by average elevation and regional average
precipitation during spring. Regional mean differences for EOS were
mainly regulated by mean temperature during autumn. Changes in
trends of SOS in the central and eastern eco-geographic regions were
coupled to the mean temperature during spring, advancing by about
7d/°C. However, in the two southwestern eco-geographic regions,
SOS was delayed significantly due to the impact of spring
precipitation. The results also showed that the SOS occurred later with
increasing elevation, as expected, with a delay rate of 0.66 d/100m.
For 2003–2012, SOS showed an advancing trend in low-elevation
areas, but a delayed trend in high-elevation areas, while EOS was
delayed in low-elevation areas, but advanced in high-elevation areas.
Grassland SOS and EOS changes may be influenced by a variety of
other environmental factors in each eco-geographic region.
Abstract: Because current wireless communication requires high
reliability in a limited bandwidth environment, this paper proposes
the variable modulation scheme based on the codebook. The variable
modulation scheme adjusts transmission power using the codebook in
accordance with channel state. Also, if the codebook is composed of
many bits, the reliability is more improved by the proposed scheme.
The simulation results show that the performance of proposed scheme
has better reliability than the the performance of conventional scheme.
Abstract: In this study, a multi objective optimization for end
milling of Al 6061 alloy has been presented to provide better
surface quality and higher Material Removal Rate (MRR). The input
parameters considered for the analysis are spindle speed, depth of cut
and feed. The experiments were planned as per Taguchis design of
experiment, with L27 orthogonal array. The Grey Relational Analysis
(GRA) has been used for transforming multiple quality responses
into a single response and the weights of the each performance
characteristics are determined by employing the Principal Component
Analysis (PCA), so that their relative importance can be properly and
objectively described. The results reveal that Taguchi based G-PCA
can effectively acquire the optimal combination of cutting parameters.
Abstract: Tannase (tannin acyl hydrolase, E.C.3.1.1.20) is an
important hydrolysable enzyme with innumerable applications and
industrial potential. In the present study, a kinetic model has been
developed for the batch fermentation used for the production of
tannase by A.flavus MTCC 3783. Maximum tannase activity of
143.30 U/ml was obtained at 96 hours under optimum operating
conditions at 35oC, an initial pH of 5.5 and with an inducer tannic
acid concentration of 3% (w/v) for a fermentation period of 120
hours. The biomass concentration reaches a maximum of 6.62 g/l at
96 hours and further there was no increase in biomass concentration
till the end of the fermentation. Various unstructured kinetic models
were analyzed to simulate the experimental values of microbial
growth, tannase activity and substrate concentration. The Logistic
model for microbial growth , Luedeking - Piret model for production
of tannase and Substrate utilization kinetic model for utilization of
substrate were capable of predicting the fermentation profile with
high coefficient of determination (R2) values of 0.980, 0.942 and
0.983 respectively. The results indicated that the unstructured models
were able to describe the fermentation kinetics more effectively.
Abstract: Workflow scheduling is an important part of cloud
computing and based on different criteria it decides cost, execution
time, and performances. A cloud workflow system is a platform
service facilitating automation of distributed applications based on
new cloud infrastructure. An aspect which differentiates cloud
workflow system from others is market-oriented business model, an
innovation which challenges conventional workflow scheduling
strategies. Time and Cost optimization algorithm for scheduling
Hybrid Clouds (TCHC) algorithm decides which resource should be
chartered from public providers is combined with a new De-De
algorithm considering that every instance of single and multiple
workflows work without deadlocks. To offset this, two new concepts
- De-De Dodging Algorithm and Priority Based Decisive Algorithm -
combine with conventional deadlock avoidance issues by proposing
one algorithm that maximizes active (not just allocated) resource use
and reduces Makespan.