Abstract: Modern applications realized onto FPGAs exhibit high connectivity demands. Throughout this paper we study the routing constraints of Virtex devices and we propose a systematic methodology for designing a novel general-purpose interconnection network targeting to reconfigurable architectures. This network consists of multiple segment wires and SB patterns, appropriately selected and assigned across the device. The goal of our proposed methodology is to maximize the hardware utilization of fabricated routing resources. The derived interconnection scheme is integrated on a Virtex style FPGA. This device is characterized both for its high-performance, as well as for its low-energy requirements. Due to this, the design criterion that guides our architecture selections was the minimal Energy×Delay Product (EDP). The methodology is fully-supported by three new software tools, which belong to MEANDER Design Framework. Using a typical set of MCNC benchmarks, extensive comparison study in terms of several critical parameters proves the effectiveness of the derived interconnection network. More specifically, we achieve average Energy×Delay Product reduction by 63%, performance increase by 26%, reduction in leakage power by 21%, reduction in total energy consumption by 11%, at the expense of increase of channel width by 20%.
Abstract: This article considers the main features of party
construction in the course of political modernization of Kazakhstan.
Along with consideration of party construction author analyzed how
the transformation of the party system was fulfilled in Kazakhstan.
Besides the basic stages in the course of party construction were
explained by the author. The statistical data is cited.
Abstract: In this paper we propose a new criterion for solving
the problem of channel shortening in multi-carrier systems. In a
discrete multitone receiver, a time-domain equalizer (TEQ) reduces
intersymbol interference (ISI) by shortening the effective duration of
the channel impulse response. Minimum mean square error (MMSE)
method for TEQ does not give satisfactory results. In [1] a new
criterion for partially equalizing severe ISI channels to reduce the
cyclic prefix overhead of the discrete multitone transceiver (DMT),
assuming a fixed transmission bandwidth, is introduced. Due to
specific constrained (unit morm constraint on the target impulse
response (TIR)) in their method, the freedom to choose optimum
vector (TIR) is reduced. Better results can be obtained by avoiding
the unit norm constraint on the target impulse response (TIR). In
this paper we change the cost function proposed in [1] to the cost
function of determining the maximum of a determinant subject to
linear matrix inequality (LMI) and quadratic constraint and solve the
resulting optimization problem. Usefulness of the proposed method
is shown with the help of simulations.
Abstract: A color image edge detection algorithm is proposed in
this paper using Pseudo-complement and matrix rotation operations.
First, pseudo-complement method is applied on the image for each
channel. Then, matrix operations are applied on the output image of
the first stage. Dominant pixels are obtained by image differencing
between the pseudo-complement image and the matrix operated
image. Median filtering is carried out to smoothen the image thereby
removing the isolated pixels. Finally, the dominant or core pixels
occurring in at least two channels are selected. On plotting the
selected edge pixels, the final edge map of the given color image is
obtained. The algorithm is also tested in HSV and YCbCr color
spaces. Experimental results on both synthetic and real world images
show that the accuracy of the proposed method is comparable to
other color edge detectors. All the proposed procedures can be
applied to any image domain and runs in polynomial time.
Abstract: In order to upgrade the seismic resistibility of structures and enhance the functionality of an isolator, a new base isolator called the multiple trench friction pendulum system (MTFPS) is proposed in this study. The proposed MTFPS isolator is composed of a trench concave surface and several intermediate sliding plates in two orthogonal directions. Mathematical formulations have been derived to examine the characteristics of the proposed MTFPS isolator possessing multiple intermediate sliding plates. By means of mathematical formulations, it can be inferred that the natural period and damping effect of the MTFPS isolator with several intermediate sliding plates can be altered continually and controllably during earthquakes. Furthermore, results obtained from shaking table tests demonstrate that the proposed isolator provides good protection to structures for prevention of damage from strong earthquakes.
Abstract: Certain tRNA synthetases have developed highly accurate molecular machinery to discriminate their cognate amino acids. Those aaRSs achieve their goal via editing reaction in the Connective Polypeptide 1 (CP1). Recently mutagenesis studies have revealed the critical importance of residues in the CP1 domain for editing activity and X-ray structures have shown binding mode of noncognate amino acids in the editing domain. To pursue molecular mechanism for amino acid discrimination, molecular modeling studies were performed. Our results suggest that aaRS bind the noncognate amino acid more tightly than the cognate one. Finally, by comparing binding conformations of the amino acids in three systems, the amino acid binding mode was elucidated and a discrimination mechanism proposed. The results strongly reveal that the conserved threonines are responsible for amino acid discrimination. This is achieved through side chain interactions between T252 and T247/T248 as well as between those threonines and the incoming amino acids.
Abstract: This paper mainly studies the analyses of parameters
in the intersection collision avoidance (ICA) system based on the radar
sensors. The parameters include the positioning errors, the repeat
period of the radar sensor, the conditions of potential collisions of two
cross-path vehicles, etc. The analyses of the parameters can provide
the requirements, limitations, or specifications of this ICA system. In
these analyses, the positioning errors will be increased as the measured
vehicle approach the intersection. In addition, it is not necessary to
implement the radar sensor in higher position since the positioning
sensitivities become serious as the height of the radar sensor increases.
A concept of the safety buffer distances for front and rear of the
measured vehicle is also proposed. The conditions for potential
collisions of two cross-path vehicles are also presented to facilitate the
computation algorithm.
Abstract: In this paper, low end Digital Signal Processors (DSPs)
are applied to accelerate integer neural networks. The use of DSPs
to accelerate neural networks has been a topic of study for some
time, and has demonstrated significant performance improvements.
Recently, work has been done on integer only neural networks, which
greatly reduces hardware requirements, and thus allows for cheaper
hardware implementation. DSPs with Arithmetic Logic Units (ALUs)
that support floating or fixed point arithmetic are generally more
expensive than their integer only counterparts due to increased circuit
complexity. However if the need for floating or fixed point math
operation can be removed, then simpler, lower cost DSPs can be
used. To achieve this, an integer only neural network is created in
this paper, which is then accelerated by using DSP instructions to
improve performance.
Abstract: Recently, several designs of single fed circularly
polarized microstrip antennas have been studied. Relatively, a few
designs for achieving circular polarization using triangular microstrip
antenna are available. Typically existing design of single fed
circularly polarized triangular microstrip antennas include the use of
equilateral triangular patch with a slit or a horizontal slot on the patch
or addition a narrow band stub on the edge or a vertex of triangular
patch.
In other word, with using a narrow band tune stub on middle of an
edge of triangle causes of facility to compensate the possible
fabrication error and substrate materials with easier adjusting the
tuner stub length. Even though disadvantages of this method is very
long of stub (approximate 1/3 length of triangle edge). In this paper,
instead of narrow band stub, a wide band stub has been applied,
therefore the length of stub by this method has been decreased
around 1/10 edge of triangle in addition changing the aperture angle
of stub, provides more facility for designing and producing circular
polarization wave.
Abstract: Global Software Development (GSD) projects are
passing through different boundaries of a company, country and even
in other continents where time zone differs between both sites.
Beside many benefits of such development, research declared plenty
of negative impacts on these GSD projects. It is important to
understand problems which may lie during the execution of GSD
project with different time zones. This research project discussed and
provided different issues related to time delays in GSD projects. In
this paper, authors investigated some of the time delay factors which
usually lie in GSD projects with different time zones. This
investigation is done through systematic review of literature.
Furthermore, the practices to overcome these delay factors which
have already been reported in literature and GSD organizations are
also explored through literature survey and case studies.
Abstract: The main purpose of the dam is to control the surface
streams and rivers across the country. Dam construction and
formation of river and big water reservoirs and resources happen in
the glen is a big incident which would change its surrounding area
considerably. In fact, constructing a dam the glen width is close and
fishes don't migrate from upstream to downstream and ultimately it
would led to their death. To resolve this, it seems necessity to create a
passage for fishes during the construction of dam. It is provided
establishing a set of stepped pools overlooking each other as a fish
way or fish ladder a proper pathway for moving fishes. In this article
we first examine the surrounding environment and then Ghazal Ozon
River and preserving the aquatics.
Abstract: We have defined two suites of metrics, which cover
static and dynamic aspects of component assembly. The static
metrics measure complexity and criticality of component assembly,
wherein complexity is measured using Component Packing Density
and Component Interaction Density metrics. Further, four criticality
conditions namely, Link, Bridge, Inheritance and Size criticalities
have been identified and quantified. The complexity and criticality
metrics are combined to form a Triangular Metric, which can be used
to classify the type and nature of applications. Dynamic metrics are
collected during the runtime of a complete application. Dynamic
metrics are useful to identify super-component and to evaluate the
degree of utilisation of various components. In this paper both static
and dynamic metrics are evaluated using Weyuker-s set of properties.
The result shows that the metrics provide a valid means to measure
issues in component assembly. We relate our metrics suite with
McCall-s Quality Model and illustrate their impact on product
quality and to the management of component-based product
development.
Abstract: Based on the homotopy perturbation method (HPM)
and Padé approximants (PA), approximate and exact solutions are
obtained for cubic Boussinesq and modified Boussinesq equations.
The obtained solutions contain solitary waves, rational solutions.
HPM is used for analytic treatment to those equations and PA for
increasing the convergence region of the HPM analytical solution.
The results reveal that the HPM with the enhancement of PA is a
very effective, convenient and quite accurate to such types of partial
differential equations.
Abstract: Collaborative working environments for distance
education can be considered as a more generic form of contemporary
remote labs. At present, the majority of existing real laboratories are
not constructed to allow the involved participants to collaborate in
real time. To make this revolutionary learning environment possible
we must allow the different users to carry out an experiment
simultaneously. In recent times, multi-user environments are
successfully applied in many applications such as air traffic control
systems, team-oriented military systems, chat-text tools, multi-player
games etc. Thus, understanding the ideas and techniques behind these
systems could be of great importance in the contribution of ideas to
our e-learning environment for collaborative working. In this
investigation, collaborative working environments from theoretical
and practical perspectives are considered in order to build an
effective collaborative real laboratory, which allows two students or
more to conduct remote experiments at the same time as a team. In
order to achieve this goal, we have implemented distributed system
architecture, enabling students to obtain an automated help by either
a human tutor or a rule-based e-tutor.
Abstract: We present our ongoing work on the development
of a new quadrotor aerial vehicle which has a tilt-wing
mechanism. The vehicle is capable of take-off/landing in vertical flight mode (VTOL) and flying over long distances in horizontal flight mode. Full dynamic model of the vehicle is derived using
Newton-Euler formulation. Linear and nonlinear controllers for
the stabilization of attitude of the vehicle and control of its
altitude have been designed and implemented via simulations. In particular, an LQR controller has been shown to be quite
effective in the vertical flight mode for all possible yaw angles. A sliding mode controller (SMC) with recursive nature has also
been proposed to stabilize the vehicle-s attitude and altitude. Simulation results show that proposed controllers provide
satisfactory performance in achieving desired maneuvers.
Abstract: Partial discharge (PD) detection is an important
method to evaluate the insulation condition of metal-clad apparatus.
Non-intrusive sensors which are easy to install and have no
interruptions on operation are preferred in onsite PD detection.
However, it often lacks of accuracy due to the interferences in PD
signals. In this paper a novel PD extraction method that uses frequency
analysis and entropy based time-frequency (TF) analysis is introduced.
The repetitive pulses from convertor are first removed via frequency
analysis. Then, the relative entropy and relative peak-frequency of
each pulse (i.e. time-indexed vector TF spectrum) are calculated and
all pulses with similar parameters are grouped. According to the
characteristics of non-intrusive sensor and the frequency distribution
of PDs, the pulses of PD and interferences are separated. Finally the
PD signal and interferences are recovered via inverse TF transform.
The de-noised result of noisy PD data demonstrates that the
combination of frequency and time-frequency techniques can
discriminate PDs from interferences with various frequency
distributions.
Abstract: Ontology is widely being used as a tool for organizing
information, creating the relation between the subjects within the
defined knowledge domain area. Various fields such as Civil,
Biology, and Management have successful integrated ontology in
decision support systems for managing domain knowledge and to
assist their decision makers. Gross pollutant traps (GPT) are devices
used in trapping and preventing large items or hazardous particles in
polluting and entering our waterways. However choosing and
determining GPT is a challenge in Malaysia as there are inadequate
GPT data repositories being captured and shared. Hence ontology is
needed to capture, organize and represent this knowledge into
meaningful information which can be contributed to the efficiency of
GPT selection in Malaysia urbanization. A GPT Ontology framework
is therefore built as the first step to capture GPT knowledge which
will then be integrated into the decision support system. This paper
will provide several examples of the GPT ontology, and explain how
it is constructed by using the Protégé tool.
Abstract: The complexity of today-s software systems makes
collaborative development necessary to accomplish tasks.
Frameworks are necessary to allow developers perform their tasks
independently yet collaboratively. Similarity detection is one of the
major issues to consider when developing such frameworks. It allows
developers to mine existing repositories when developing their own
views of a software artifact, and it is necessary for identifying the
correspondences between the views to allow merging them and
checking their consistency. Due to the importance of the
requirements specification stage in software development, this paper
proposes a framework for collaborative development of Object-
Oriented formal specifications along with a similarity detection
approach to support the creation, merging and consistency checking
of specifications. The paper also explores the impact of using
additional concepts on improving the matching results. Finally, the
proposed approach is empirically evaluated.
Abstract: Personal computers draw non-sinusoidal current
with odd harmonics more significantly. Power Quality of
distribution networks is severely affected due to the flow of these
generated harmonics during the operation of electronic loads. In
this paper, mathematical modeling of odd harmonics in current like
3rd, 5th, 7th and 9th influencing the power quality has been presented.
Live signals have been captured with the help of power quality
analyzer for analysis purpose. The interesting feature is that Total
Harmonic Distortion (THD) in current decreases with the increase
of nonlinear loads has been verified theoretically. The results
obtained using mathematical expressions have been compared with
the practical results and exciting results have been found.
Abstract: Tofurther advance research on immune-related genes
from T. molitor, we constructed acDNA library and analyzed
expressed sequence taq (EST) sequences from 1,056 clones. After
removing vector sequence and quality checkingthrough thePhred
program (trim_alt 0.05 (P-score>20), 1039 sequences were generated.
The average length of insert was 792 bp. In addition, we identified 162
clusters, 167 contigs and 391 contigs after clustering and assembling
process using a TGICL package. EST sequences were searchedagainst
NCBI nr database by local BLAST (blastx, E