Abstract: Ren et al. presented an efficient carrier frequency offset
(CFO) estimation method for orthogonal frequency division multiplexing
(OFDM), which has an estimation range as large as the
bandwidth of the OFDM signal and achieves high accuracy without
any constraint on the structure of the training sequence. However,
its detection probability of the integer frequency offset (IFO) rapidly
varies according to the fractional frequency offset (FFO) change. In
this paper, we first analyze the Ren-s method and define two criteria
suitable for detection of IFO. Then, we propose a novel method for
the IFO estimation based on the maximum-likelihood (ML) principle
and the detection criteria defined in this paper. The simulation results
demonstrate that the proposed method outperforms the Ren-s method
in terms of the IFO detection probability irrespective of a value of
the FFO.
Abstract: An ultrasound-assisted activation method for
electroless silver plating is presented in this study. When the
ultrasound was applied during the activation step, the amount of the Pd
species adsorbed on substrate surfaces was higher than that of sample
pretreated with a conventional activation process without ultrasound
irradiation. With this activation method, it was also shown that the
adsorbed Pd species with a size of about 5 nm were uniformly
distributed on the surfaces, thus a smooth and uniform coating on the
surfaces was obtained by subsequent electroless silver plating. The
samples after each step were characterized by AFM, XPS, FIB, and
SEM.
Abstract: NFκB activation plays a crucial role in anti-apoptotic responses in response to the apoptotic signaling during tumor necrosis factor (TNFa) stimulation in Multiple Myeloma (MM). Although several drugs have been found effective for the treatment of MM by mainly inhibiting NFκB pathway, there are no any quantitative or qualitative results of comparison assessment on inhibition effect between different single drugs or drug combinations. Computational modeling is becoming increasingly indispensable for applied biological research mainly because it can provide strong quantitative predicting power. In this study, a novel computational pathway modeling approach is employed to comparably assess the inhibition effects of specific single drugs and drug combinations on the NFκB pathway in MM, especially the prediction of synergistic drug combinations.
Abstract: Weather disaster events were frequent and caused loss
of lives and property in Taiwan recently. Excessive concentration of
population and lacking of integrated planning led to Taiwanese coastal
zone face the impacts of climate change directly. Comparing to many
countries which have already set up legislation, competent authorities
and national adaptation strategies, the ability of coastal management
adapting to climate change is still insufficient in Taiwan. Therefore, it
is necessary to establish a complete institutional arrangement for
coastal management due to climate change in order to protect
environment and sustain socio-economic development. This paper
firstly reviews the impact of climate change on Taiwanese coastal
zone. Secondly, development of Taiwanese institutional arrangement
of coastal management is introduced. Followed is the analysis of four
dimensions of legal basis, competent authority, scientific and financial
support and international cooperations of institutional arrangement.
The results show that Taiwanese government shall: 1) integrate climate
change issue into Coastal Act, Wetland Act and territorial planning
Act and pass them; 2) establish the high level competent authority for
coastal management; 3) set up the climate change disaster coordinate
platform; 4) link scientific information and decision markers; 5)
establish the climate change adjustment fund; 6) participate in
international climate change organizations and meetings actively; 7)
cooperate with near countries to exchange experiences.
Abstract: This research was conducted for the first time at the
southeastern coasts of the Caspian Sea in order to evaluate the
performance of osteichthyes cooperatives through production (catch)
function. Using one of the indirect valuation methods in this research,
contributory factors in catch were identified and were inserted into
the function as independent variables. In order to carry out this
research, the performance of 25 Osteichthyes catching cooperatives
in the utilization year of 2009 which were involved in fishing in
Miankale wildlife refuge region. The contributory factors in catch
were divided into groups of economic, ecological and biological
factors. In the mentioned function, catch rate of the cooperative were
inserted into as the dependant variable and fourteen partial variables
in terms of nine general variables as independent variables. Finally,
after function estimation, seven variables were rendered significant at
99 percent reliably level. The results of the function estimation
indicated that human resource (fisherman quantity) had the greatest
positive effect on catch rate with an influence coefficient of 1.7 while
weather conditions had the greatest negative effect on the catch rate
of cooperatives with an influence coefficient of -2.07. Moreover,
factors like member's share, experience and fisherman training and
fishing effort played the main roles in the catch rate of cooperative
with influence coefficients of 0.81, 0.5 and 0.21, respectively.
Abstract: The increased number of automobiles in recent years
has resulted in great demand for fossil fuel. This has led to the
development of automobile by using alternative fuels which include
gaseous fuels, biofuels and vegetables oils as fuel. Energy from
biomass and more specific bio-diesel is one of the opportunities that
could cover the future demand of fossil fuel shortage. Biomass in the
form of cashew nut shell represents a new energy source and
abundant source of energy in India. The bio-fuel is derived from
cashew nut shell oil and its blend with diesel are promising
alternative fuel for diesel engine. In this work the pyrolysis Cashew
Nut Shell Liquid (CNSL)-Diesel Blends (CDB) was used to run the
Direct Injection (DI) diesel engine. The experiments were conducted
with various blends of CNSL and Diesel namely B20, B40, B60, B80
and B100. The results are compared with neat diesel operation. The
brake thermal efficiency was decreased for blends of CNSL and
Diesel except the lower blends of B20. The brake thermal efficiency
of B20 is nearly closer to that of diesel fuel. Also the emission level
of the all CNSL and Diesel blends was increased compared to neat
diesel. The higher viscosity and lower volatility of CNSL leads to
poor mixture formation and hence lower brake thermal efficiency and
higher emission levels. The higher emission level can be reduced by
adding suitable additives and oxygenates with CNSL and Diesel
blends.
Abstract: Reliability is one of the most important quality attributes of software. Based on the approach of Reussner and the approach of Cheung, we proposed the reliability prediction model of component-based software architectures. Also, the value of the model is shown through the experimental evaluation on a web server system.
Abstract: In the current research, neuro-fuzzy model and regression model was developed to predict Material Removal Rate in Electrical Discharge Machining process for AISI D2 tool steel with copper electrode. Extensive experiments were conducted with various levels of discharge current, pulse duration and duty cycle. The experimental data are split into two sets, one for training and the other for validation of the model. The training data were used to develop the above models and the test data, which was not used earlier to develop these models were used for validation the models. Subsequently, the models are compared. It was found that the predicted and experimental results were in good agreement and the coefficients of correlation were found to be 0.999 and 0.974 for neuro fuzzy and regression model respectively
Abstract: Soil washing process with a surfactant solution is a potential technology for the rapid removal of hydrophobic organic compound (HOC) from soil. However, large amount of washed water would be produced during operation and this should be treated effectively by proper methods. The soil washed water for complex contaminated site with HOC and heavy metals might contain high amount of pollutants such as HOC and heavy metals as well as used surfactant. The heavy metals in the soil washed water have toxic effects on microbial activities thus these should be removed from the washed water before proceeding to a biological waste-water treatment system. Moreover, the used surfactant solutions are necessary to be recovered for reducing the soil washing operation cost. In order to simultaneously remove the heavy metals and HOC from soil-washed water, activated carbon (AC) was used in the present study. In an anionic-nonionic surfactant mixed solution, the Cd(II) and phenanthrene (PHE) were effectively removed by adsorption on activated carbon. The removal efficiency for Cd(II) was increased from 0.027 mmol-Cd/g-AC to 0.142 mmol-Cd/g-AC as the mole ratio of SDS increased in the presence of PHE. The adsorptive capacity of PHE was also increased according to the SDS mole ratio due to the decrement of molar solubilization ratios (MSR) for PHE in an anionic-nonionic surfactant mixture. The simultaneous adsorption of HOC and cationic heavy metals using activated carbon could be a useful method for surfactant recovery and the reduction of heavy metal toxicity in a surfactant-enhanced soil washing process.
Abstract: In an assessment of the extractability of metals in
green liquor dregs from the chemical recovery circuit of semichemical
pulp mill, extractable concentrations of heavy metals in
artificial gastric fluid were between 10 (Ni) and 717 (Zn) times
higher than those in artificial sweat fluid. Only Al (6.7 mg/kg; d.w.),
Ni (1.2 mg/kg; d.w.) and Zn (1.8 mg/kg; d.w.) showed extractability
in the artificial sweat fluid, whereas Al (730 mg/kg; d.w.), Ba (770
mg/kg; d.w.) and Zn (1290 mg/kg; d.w.) showed clear extractability
in the artificial gastric fluid. As certain heavy metals were clearly
soluble in the artificial gastric fluid, the careful handling of this
residue is recommended in order to prevent the penetration of green
liquor dregs across the human gastrointestinal tract.
Abstract: Analytical expression for maximum power transfer
through a transmission line limited by voltage stability has been
formulated using exact representation of transmission line with
ABCD parameters. The expression has been used for plotting PV
curve at different power factors of a radial transmission line.
Limiting values of reactive power have been obtained.
Abstract: The adsorption properties of CO and H2 on iron-based
catalyst with addition of Zr and Ni were investigated using
temperature programmed desorption process. It was found that on the
carburized iron-based catalysts, molecular state and dissociative state
CO existed together. The addition of Zr was preferential for the
molecular state adsorption of CO on iron-based catalyst and the
presence of Ni was beneficial to the dissociative adsorption of CO. On
H2 reduced catalysts, hydrogen mainly adsorbs on the surface iron
sites and surface oxide sites. On CO reduced catalysts, hydrogen
probably existed as the most stable CH and OH species. The addition
of Zr was not benefit to the dissociative adsorption of hydrogen on
iron-based catalyst and the presence of Ni was preferential for the
dissociative adsorption of hydrogen.
Abstract: This investigation examines the effect of the sintering
temperature curve in manufactured nickel powder capillary structure
(wick) for a loop heat pipe (LHP). The sintering temperature curve is
composed of a region of increasing temperature; a region of constant
temperature and a region of declining temperature. The most important
region is that in which the temperature increases, as an index in the
stage in which the temperature increases. The wick of nickel powder is
manufactured in the stage of fixed sintering temperature and the time
between the stage of constant temperature and the stage of falling
temperature. When the slope of the curve in the region of increasing
temperature is unity (equivalent to 10 °C/min), the structure of the
wick is complete and the heat transfer performance is optimal. The
result of experiment test demonstrates that the heat transfer
performance is optimal at 320W; the minimal total thermal resistance
is approximately 0.18°C/W, and the heat flux is 17W/cm2; the internal
parameters of the wick are an effective pore radius of 3.1 μm, a
permeability of 3.25×10-13m2 and a porosity of 71%.
Abstract: A 2-Degrees of freedom powered prosthetic wrist
actuator has been proposed that can provide the Abduction/Adduction
& Flexion/Extension movements of the human wrist. The basic
structure of the actuator is a Ball and Socket joint and the force is
transmitted from the DC geared servo motors to the joint through the
Bowden cables. The proposed design is capable of providing the
required DOF in both axes i.e. 85° & 90° in flexion extension axis.
The size and weight of the actuator lies within the ranges of an
average human being-s wrist.
Abstract: This paper mainly about the study on one of the
widely used error correcting codes that is Low parity check Codes
(LDPC). In this paper, the Regular LDPC code has been discussed
The LDPC codes explained in this paper is about the Regular Binary
LDPC codes or the Gallager.
Abstract: Silver nano-particles have been used for antibacterial
purpose and it is also believed to have removal of odorous compounds,
oxidation capacity as a metal catalyst. In this study, silver
nano-particles in nano sizes (5-30 nm) were prepared on the surface of
NaHCO3, the supporting material, using a sputtering method that
provided high silver content and minimized conglomerating problems
observed in the common AgNO3 photo-deposition method. The silver
nano-particles were dispersed by dissolving Ag-NaHCO3 into water,
and the dispersed silver nano-particles in the aqueous phase were
applied to remove inorganic odor compounds, H2S, in a scrubbing
reactor. Hydrogen sulfide in the gas phase was rapidly removed by the
silver nano-particles, and the concentration of sulfate (SO4
2-) ion
increased with time due to the oxidation reaction by silver as a
catalyst. Consequently, the experimental results demonstrated that the
silver nano-particles in the aqueous solution can be successfully
applied to remove odorous compounds without adding additional
energy sources and producing any harmful byproducts
Abstract: With today's fast lifestyles and busy schedule, nuclear
families are becoming popular. Thus, the elderly members of these
families are often neglected. This has lead to the popularity of the
concept of Community living for the aged. The elders reside at a
centre, which is controlled by the MANAGER. The manager takes
responsibility of the functioning of the centre which includes taking
care of 'residents' at the centre along with managing the daily chores
of the centre, which he accomplishes with the help of a number of
staff members and volunteers Often the Manager is not an employee
but a volunteer. In such cases especially, time is an important
constraint. A system, which provides an easy and efficient manner of
managing the working of an old age home in detail, will prove to be
of great benefit. We have developed a P.C. based organizer used to
monitor the various activities of an old age home. It is an effective
and easy-to-use system which will enable the manager to keep an
account of all the residents, their accounts, staff members, volunteers,
the centre-s logistic requirements etc. It is thus, a comprehensive
'Organizer' for Old Age Homes.
Abstract: In image processing and visualization, comparing two
bitmapped images needs to be compared from their pixels by matching
pixel-by-pixel. Consequently, it takes a lot of computational time
while the comparison of two vector-based images is significantly
faster. Sometimes these raster graphics images can be approximately
converted into the vector-based images by various techniques. After
conversion, the problem of comparing two raster graphics images
can be reduced to the problem of comparing vector graphics images.
Hence, the problem of comparing pixel-by-pixel can be reduced to
the problem of polynomial comparisons. In computer aided geometric
design (CAGD), the vector graphics images are the composition of
curves and surfaces. Curves are defined by a sequence of control
points and their polynomials. In this paper, the control points will be
considerably used to compare curves. The same curves after relocated
or rotated are treated to be equivalent while two curves after different
scaled are considered to be similar curves. This paper proposed an
algorithm for comparing the polynomial curves by using the control
points for equivalence and similarity. In addition, the geometric
object-oriented database used to keep the curve information has also
been defined in XML format for further used in curve comparisons.
Abstract: β-Glucosidase is an important enzyme for production
of ethanol from lignocellulose. With hydrolytic activity on
cellooligosaccharides, especially cellobiose, β-glucosidase removes
product inhibitory effect on cellulases and forms fermentable sugars.
In this study, β-glucosidase encoding gene (BGL1) from traditional
starter yeast Saccharomycosis fibuligera BMQ908 was cloned and
expressed in Pichia pastoris. BGL1 of S. fibuligera BMQ 908 shared
98% nucleotide homology with the closest GenBank sequence
(M22475) but identity in amino-acid sequences of catalytic domains.
Recombinant plasmid pPICZαA/BGL1 containing the sequence
encoding BGL1 mature protein and α-factor secretion signal was
constructed and transformed into methylotrophic yeast P. pastoris by
electroporation. The recombinant strain produced single extracellular
protein with molecular weight of 120 kDa and cellobiase activity of
60 IU/ml. The optimum pH of the recombinant β-glucosidase was 5.0
and the optimum temperature was 50°C.