Abstract: Geosynthetics have proved to be suitable for
reinforced soil retaining walls. Based on the increasing uses of
geosynthetic reinforced soil systems in the regions, which bear
frequent earthquakes, the study of dynamic behavior of structures
seems necessary. Determining the reinforcement forces is; therefore,
one of the most important and main points of discussions in
designing retaining walls, by which we prevent from conservative
planning. Thus, this paper intended to investigate the effects of such
parameters as wall height, acceleration type, vertical spacing of
reinforcement, type of reinforcement and soil type on forces and
deformation through numerical modeling of the geosynthetic
reinforced soil retaining walls (GRSRW) under dynamic loading with
finite difference method by using FLAC. The findings indicate rather
positive results with each parameter.
Abstract: In this study, a three-dimensional haptotaxis model to simulate the migration of a population of cancer cells has been proposed. The invasion of cancer cells is related with the hapto-attractant and the effect of the interface energies between the cells and the ECM. The diffuse interface model, which incorporates the haptotaxis mechanism and interface energies, is employed. The semi-implicit Fourier spectral scheme is adopted for efficient evaluation of the simulation. The simulation results thoroughly reveal the dynamics of cancer-cell migration.
Abstract: This paper proposes a neural network weights and
topology optimization using genetic evolution and the
backpropagation training algorithm. The proposed crossover and
mutation operators aims to adapt the networks architectures and
weights during the evolution process. Through a specific inheritance
procedure, the weights are transmitted from the parents to their
offsprings, which allows re-exploitation of the already trained
networks and hence the acceleration of the global convergence of the
algorithm. In the preprocessing phase, a new feature extraction
method is proposed based on Legendre moments with the Maximum
entropy principle MEP as a selection criterion. This allows a global
search space reduction in the design of the networks. The proposed
method has been applied and tested on the well known MNIST
database of handwritten digits.
Abstract: This work provides a practical method for the
development of rural road networks in rural areas of developing
countries. The proposed methodology enables to determine
obligatory points in the rural road network maximizing the number of
settlements that have access to basic services within a given
maximum distance. The proposed methodology is simple and
practical, hence, highly applicable to real-world scenarios, as
demonstrated in the definition of the road network for the rural areas
of Nepal.
Abstract: Mobile ad hoc network is a collection of mobile
nodes communicating through wireless channels without any
existing network infrastructure or centralized administration.
Because of the limited transmission range of wireless network
interfaces, multiple "hops" may be needed to exchange data
across the network. Consequently, many routing algorithms
have come into existence to satisfy the needs of
communications in such networks. Researchers have
conducted many simulations comparing the performance of
these routing protocols under various conditions and
constraints. One question that arises is whether speed of nodes
affects the relative performance of routing protocols being
studied. This paper addresses the question by simulating two
routing protocols AODV and DSDV. Protocols were
simulated using the ns-2 and were compared in terms of
packet delivery fraction, normalized routing load and average
delay, while varying number of nodes, and speed.
Abstract: This paper was aimed to survey the level of awareness
of traditional grocery stores in Bangkok in these categories: location,
service quality, risk, shopping, worthwhile, shopping satisfaction, and
future shopping intention. The paper was also aimed to survey factors
influencing the decision to shop at traditional grocery stores in
Bangkok in the future. The findings revealed that consumers had a
high level of awareness of traditional grocery stores in Bangkok.
Consumers were aware that the price was higher and it was riskier to
buy goods and services at traditional grocery stores but they still had
a high level of preference to patronage traditional grocery stores. This
was due to the reasons that there was a high level of satisfaction from
the factors of the friendliness of the owner, the ability to negotiate the
price, the ability to buy on credit, free delivery, and the enjoyment to
meet with other customers in the same neighborhood.
Abstract: The sonochemical decolorization and degradation of azo dye Methyl violet using Fenton-s reagent in the presence of a high-frequency acoustic field has been investigated. Dyeing and textile effluents are the major sources of azo dyes, and are most troublesome among industrial wastewaters, causing imbalance in the eco-system. The effect of various operating conditions (initial concentration of dye, liquid-phase temperature, ultrasonic power and frequency and process time) on sonochemical degradation was investigated. Conversion was found to increase with increase in initial concentration, temperature, power level and frequency. Both horntype and tank-type sonicators were used, at various power levels (250W, 400W and 500W) for frequencies ranging from 20 kHz - 1000 kHz. A 'Process Intensification' parameter PI, was defined to quantify the enhancement of the degradation reaction by ultrasound when compared to control (i.e., without ultrasound). The present work clearly demonstrates that a high-frequency ultrasonic bath can be used to achieve higher process throughput and energy efficiency at a larger scale of operation.
Abstract: Based on the combined shape feature and texture
feature, a fast object detection method with rotation invariant features
is proposed in this paper. A quick template matching scheme based
online learning designed for online applications is also introduced in
this paper. The experimental results have shown that the proposed
approach has the features of lower computation complexity and
higher detection rate, while keeping almost the same performance
compared to the HOG-based method, and can be more suitable for
run time applications.
Abstract: This paper describes topic of computer simulation with regard to the ground movement above an underground mine. Simulation made with software package ADINA for nonlinear elastic-plastic analysis with finite elements method. The one of representative profiles from Mine 'Stara Jama' in Zenica has been investigated. A collection and selection of both geo-mechanical data and geometric parameters of the mine was necessary for performing these simulations. Results of estimation have been compared with measured values (vertical displacement of surface), and then simulation performed with assumed dynamic and dimensions of excavation, over a period of time. Results are presented with bitmaps and charts.
Abstract: This paper studies mechanical buckling of
functionally graded beams subjected to axial compressive load that is
simply supported at both ends lies on a continuous elastic foundation.
The displacement field of beam is assumed based on Engesser-Timoshenko beam theory. Applying the Hamilton's principle, the
equilibrium equation is established. The influences of dimensionless geometrical parameter, functionally graded index and foundation
coefficient on the critical buckling load of beam are presented. To investigate the accuracy of the present analysis, a compression study
is carried out with a known data.
Abstract: In this work, we study elliptic divisibility sequences
over finite fields. Morgan Ward in [14], [15] gave arithmetic theory
of elliptic divisibility sequences and formulas for elliptic divisibility
sequences with rank two over finite field Fp. We study elliptic
divisibility sequences with rank three, four and five over a finite field
Fp, where p > 3 is a prime and give general terms of these sequences
and then we determine elliptic and singular curves associated with
these sequences.
Abstract: Design of a constant chord propeller is presented in
this paper in order to reduce propeller-s design procedure-s costs. The
design process was based on Lock and Goldstein-s techniques of
propeller design and analysis. In order to calculate optimum chord of
propeller, chord of a referential element is generalized as whole
blades chord. The design outcome which named CS-X-1 is modeled
& analyzed by CFD methods using K-ε: R.N.G turbulence model.
Convergence of results of two codes proved that outcome results of
design process are reliable. Design result is a two-blade propeller
with a total diameter of 1.1 meter, radial velocity of 3000 R.P.M,
efficiency above .75 and power coefficient near 1.05.
Abstract: The work describes the use of a synthetic transmit
aperture (STA) with a single element transmitting and all elements
receiving in medical ultrasound imaging. STA technique is a novel
approach to today-s commercial systems, where an image is acquired
sequentially one image line at a time that puts a strict limit on the
frame rate and the amount of data needed for high image quality. The
STA imaging allows to acquire data simultaneously from all
directions over a number of emissions, and the full image can be
reconstructed.
In experiments a 32-element linear transducer array with 0.48 mm
inter-element spacing was used. Single element transmission aperture
was used to generate a spherical wave covering the full image region.
The 2D ultrasound images of wire phantom are presented obtained
using the STA and commercial ultrasound scanner Antares to
demonstrate the benefits of the SA imaging.
Abstract: A two-dimensional thin-walled capsule of a flexible
semi-permeable membrane is adhered onto a rigid planar substrate
under adhesive forces (derived from a potential function) in the
presence of osmosis across the membrane. The capsule is immersed
in a hypotonic and diluted binary solution of a non-electrolyte
solute. The Stokes flow problem is solved by the immersed interface
method (IIM) with equal viscosities for the enclosed and
surrounding fluid of the capsule. The numerical results obtained are
verified against two simplified theoretical solutions and the
agreements are good. The osmotic inflation of the adhered capsule is
studied as a function of the solute concentration field, hydraulic
conductivity, and the initial capsule shape. Our findings indicate that
the contact length shrinks in dimension as capsule inflates in the
hypotonic medium, and the equilibrium contact length does not
depend on the hydraulic conductivity of the membrane and the
initial shape of the capsule.
Abstract: With the fast progression of data exchange in electronic way, information security is becoming more important in data storage and transmission. Because of widely using images in industrial process, it is important to protect the confidential image data from unauthorized access. In this paper, we analyzed current image encryption algorithms and compression is added for two of them (Mirror-like image encryption and Visual Cryptography). Implementations of these two algorithms have been realized for experimental purposes. The results of analysis are given in this paper.
Abstract: In this paper, we investigate multihop polling and data gathering schemes in layered sensor networks in order to extend the life time of the networks. A network consists of three layers. The lowest layer contains sensors. The middle layer contains so called super nodes with higher computational power, energy supply and longer transmission range than sensor nodes. The top layer contains a sink node. A node in each layer controls a number of nodes in lower layer by polling mechanism to gather data. We will present four types of data gathering schemes: intermediate nodes do not queue data packet, queue single packet, queue multiple packets and aggregate data, to see which data gathering scheme is more energy efficient for multihop polling in layered sensor networks.
Abstract: In recent years, there have been attempts to store
natural gas in adsorptive form. This is called adsorptive natural gas,
or ANG. The problem with this technology is the low sorption
capacity. The purpose is to achieve compressed natural gas (CNG)
capacity of 230 V/V. Further research is required to achieve such
target. Several research studies have been performed with this target;
through either the modification or development of new sorbents or
the optimization of the operation sorption process itself. In this work,
storage of methane on molecular sieves 5A and 13X was studied on
dry basis, and on wet basis to certain extent. The temperature and the
pressure dynamics were investigated. The results indicated that
regardless of the charge pressure, the time for the peak temperature
during the methane charge process is always the same. This can be
used as a characteristic of the adsorbent. The total achieved
deliveries using molecular sieves were much lower than that of
activated carbons; 53.0 V/V for the case of 13X molecular sieves and
43 V/V for the case of 5A molecular sieves, both at 2oC and 4 MPa
(580 psi). Investigation of charge pressure dynamic using wet
molecular sieves at 2oC and a mass ratio of 0.5, revealed slowness of
the process and unexpected behavior.
Abstract: In order to apply partially filled steel grid composite deck as the horizontal supporting structure of various kinds of infrastructures, the variation of its flexural strength according to design parameters such as cross and longitudinal bars constituting the steel grid and the type of shear connection is evaluated and compared experimentally. The result shows that the design sensitivity of the deck to the spacing of the cross bars is insignificant in the case of structure with low risk of punching failure or without load distribution problem. By means of shear connection composed by transverse rebar and longitudinal bar without additional shear stud bolts, the complete interaction between steel grid and concrete slab is able to be achieved and the composite deck can develop its bending resistance capacity.
Abstract: Classification of Persian printed numeral characters
has been considered and a proposed system has been introduced. In
representation stage, for the first time in Persian optical character
recognition, extended moment invariants has been utilized as
characters image descriptor. In classification stage, four different
classifiers namely minimum mean distance, nearest neighbor rule,
multi layer perceptron, and fuzzy min-max neural network has been
used, which first and second are traditional nonparametric statistical
classifier. Third is a well-known neural network and forth is a kind of
fuzzy neural network that is based on utilizing hyperbox fuzzy sets.
Set of different experiments has been done and variety of results has
been presented. The results showed that extended moment invariants
are qualified as features to classify Persian printed numeral
characters.
Abstract: It has been shown that a load discontinuity at the end of
an impulse will result in an extra impulse and hence an extra amplitude
distortion if a step-by-step integration method is employed to yield the
shock response. In order to overcome this difficulty, three remedies
are proposed to reduce the extra amplitude distortion. The first remedy
is to solve the momentum equation of motion instead of the force
equation of motion in the step-by-step solution of the shock response,
where an external momentum is used in the solution of the momentum
equation of motion. Since the external momentum is a resultant of the
time integration of external force, the problem of load discontinuity
will automatically disappear. The second remedy is to perform a single
small time step immediately upon termination of the applied impulse
while the other time steps can still be conducted by using the time step
determined from general considerations. This is because that the extra
impulse caused by a load discontinuity at the end of an impulse is
almost linearly proportional to the step size. Finally, the third remedy
is to use the average value of the two different values at the integration
point of the load discontinuity to replace the use of one of them for
loading input. The basic motivation of this remedy originates from the
concept of no loading input error associated with the integration point
of load discontinuity. The feasibility of the three remedies are
analytically explained and numerically illustrated.